When configuring the MDIO subsystem it is also necessary to configure
the TBI register. Make sure the TBI is contained within the mapped
register range in order to:
a) make sure the address is computed correctly
b) make users aware that we're actually accessing that register

In case of error, print a message but continue anyway.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Timur Tabi <timur@tabi.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

RTA_ALIGNTO is currently define as 4. It has to be 4U to prevent warning
for RTA_ALIGN and RTA_DATA expansions when -Wconversion gcc option is
enabled.
This follows NLMSG_ALIGNTO definition in <include/uapi/linux/netlink.h>.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a clone of commit 2ab95749 ("ip_forward: Drop frames with
attached skb->sk") for ipv6.

This commit has exactly the same reasons as the above mentioned commit,
namely to prevent panics during netfilter reload or a misconfigured stack.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

GRE point-to-point interfaces should also support ipv6 multicast. Setting
up default multicast routes on interface creation was forgotten. Add it.

Bugzilla: <https://bugzilla.kernel.org/show_bug.cgi?id=103231>
Cc: Julien Muchembled <jm@jmuchemb.eu>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dumazet <ndumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Configuring 4-tuple RSS hsahing for UDP
[E.g., by using `ethtool -N <interface> rx-flow-hash udp4 sdfn']
on a 57710/57711 adapter would cause it to assert as HW does not
support such a configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: couple of fixes

Just a couple of small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When calculating the shift needed in order to access a bit array element
in a byte, we should multiply the index by the element size and not
assume it is fixed at 2-bits.

Fixes: 93c1edb2 ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 31557f0f ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to commit c0afd9ce ("fq_codel: fix return value of fq_codel_drop()")
->drop() is supposed to return the number of bytes it dropped,
but hhf_drop () returns the id of the bucket where it drops
a packet from.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Terry Lam <vtlam@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
Mellanox driver update to 4.3-rc4

Small set of fixes for net, which includes Carol's patches, a fix
from Achiad to have the right behaviour for mlx5 Eth devices w.r.t
VLANs in promiscuous mode, a good-bye patch from Ido who left Mellanox
and the 1st patch from Jiri to our NIC drivers (I love one-liners)...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove Ido Shamay as co-maintainer for the mlx4 Ethernet driver,
as he no longer works for Mellanox.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the device was set to promiscuous mode, we didn't disable
VLAN filtering, which is wrong behaviour, fix that.

Now when the device is set to promiscuous mode RX packets
sent over any VLAN (or no VLAN tag at all) will be accepted.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We used the wrong register name for querying the PVLC register

Fixes: a124d13e ('net/mlx5_core: Add more query port helpers')
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test interrupts fails if not all completion vectors called
request_irq. This case happens if only mlx4_en is loaded and
we have more completion vectors than rx rings.

Fixes: c66fa19c ('net/mlx4: Add EQ pool')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we get MAX_MSIX interrupts would like to have each receive ring
with his own msix interrupt line. Do not need the shared_ports
variable at mlx4_enable_msix

Fixes: 9293267a ('net/mlx4_core: Capping number of requested MSIXs to MAX_MSIX')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"Y" was the right answer for MDIO_OCTEON when this option was only
available on CAVIUM_OCTEON_SOC. But now that the option is visible on
all (64-bit) systems, this piece of advice no longer makes sense. This
helper module is selected automatically by drivers which need it
anyway.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: a6d67864 ("net: mdio-octeon: Modify driver to work on both ThunderX and Octeon")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recently added mlxsw driver produces warnings in ARM
allmodconfig:

drivers/net/ethernet/mellanox/mlxsw/pci.c: In function 'mlxsw_pci_cmd_exec':
drivers/net/ethernet/mellanox/mlxsw/pci.c:1585:59: warning: right shift count >= width of type [-Wshift-count-overflow]
linux/byteorder/big_endian.h:38:51: note: in definition of macro '__cpu_to_be32'
drivers/net/ethernet/mellanox/mlxsw/pci.c:76:2: note: in expansion of macro 'iowrite32be'

This uses upper_32_bits() to extract the bits while avoiding that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Fixes: eda6500a "mlxsw: Add PCI bus implementation"
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to commit c29390c6 ("xps: must clear sender_cpu before forwarding")
the skb->sender_cpu needs to be cleared before xmit.

Fixes: 3896d655 ("bpf: introduce bpf_clone_redirect() helper")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to commit c29390c6 ("xps: must clear sender_cpu before forwarding")
the skb->sender_cpu needs to be cleared when moving from Rx
Tx, otherwise kernel could crash.

Fixes: 2bd82484 ("xps: fix xps for stacked devices")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make unix_sk() just like inet[6]_sk() by constify'ing the sock
parameter.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joe Stringer says:

====================
OVS conntrack fixes for net

The userspace side of the Open vSwitch conntrack changes is currently
undergoing review, which has highlighted some minor bugs in the existing
conntrack implementation in the kernel, as well as pointing out some
future-proofing that can be done on the interface to reduce the need for
additional compatibility code in future.

The biggest changes here are to the userspace API for the ct_state match
field and the CT action. This series proposes to firstly extend the ct_state
match field to 32 bits, ensuring to reject any currently unsupported bits.
Secondly, rather than representing CT action flags within a 32-bit field,
simply use a netlink attribute as presence of the single flag that is
defined today. This also serves to reject unsupported ct action flag bits.

v4: Use 12-character abbreviated hashes in commit messages.
v3: Fully acked.
v2: Address minor style feedback, add acks.
v1: Initial post.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, the CT_ATTR_FLAGS attribute, when nested under the
OVS_ACTION_ATTR_CT, encoded a 32-bit bitmask of flags that modify the
semantics of the ct action. It's more extensible to just represent each
flag as a nested attribute, and this requires no additional error
checking to reject flags that aren't currently supported.
Suggested-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ct_state field was initially added as an 8-bit field, however six of
the bits are already being used and use cases are already starting to
appear that may push the limits of this field. This patch extends the
field to 32 bits while retaining the internal representation of 8 bits.
This should cover forward compatibility of the ABI for the foreseeable
future.

This patch also reorders the OVS_CS_F_* bits to be sequential.
Suggested-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, if userspace specified ct_state bits in the flow key which
are currently undefined (and therefore unsupported), then they would be
ignored. This could cause unexpected behaviour in future if userspace is
extended to support additional bits but attempts to communicate with the
current version of the kernel. This patch rectifies the situation by
rejecting such ct_state bits.

Fixes: 7f8a436e "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ct action uses parts of the flow key, so we need to ensure that it
is valid before executing that action.

Fixes: 7f8a436e "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If ovs_fragment() was unable to fragment the skb due to an L2 header
that exceeds the supported length, skbs would be leaked. Fix the bug.

Fixes: 7f8a436e "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These comments hadn't caught up to their implementations, fix them.

Fixes: 7f8a436e "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Neil Armstrong says:

====================
net: dsa: complete and fix the dsa unbinding

In order to cleanly unbind the dsa core, either as a module removal,
or a platform device unbind, switch the allocation the their devm_
counterparts and complete the destroy functions.

First, the missing kfree were added, the remove function were
completed then kfree were removed in favor to devm_ calls.

The last patch is an way to cleanly exit the probe when no
switch is found in the discover process.

The patches are based on the current net.

v3:
 - make checkpatch happy with 1/5 & 5/5
 - fix 5/5 exit path with a goto
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If no switch were found in dsa_setup_dst, return -ENODEV and
exit the dsa_probe cleanly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now the kfree calls exists in the the remove functions, remove them in all
places except the of_probe functions and replace allocation calls
with their devm_ counterparts.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When unbinding dsa, complete the dsa_switch_destroy to unregister the
fixed link phy then cleanly unregister and destroy the net devices.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To prevent memory leakage on unbinding, add missing mdiobus unregister
and unallocation calls.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To prevent memory leakage on unbinding, add missing kfree calls.
Includes minor cosmetic change to make patch clean.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It occurred to me yesterday that 741a11d9 ("net: ipv6: Add
RT6_LOOKUP_F_IFACE flag if oif is set") means that xfrm6_dst_lookup
needs the FLOWI_FLAG_SKIP_NH_OIF flag set. This latest commit causes
the oif to be considered in lookups which is known to break vti. This
explains why 58189ca7 did not the IPv6 change at the time it was
submitted.

Fixes: 42a7b32b ("xfrm: Add oif to dst lookups")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The standard way to check if the AQ is enabled is to look at the
count field. So we should only set this field after we have
successfully allocated memory. To do otherwise is to incite
panic among the populace.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kasprintf function can return NULL if the allocation fails. Check for
successful allocation before attempting to use the returned buffer.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not every device has dev->tstats set. So when OVS tries to calculate
vport stats it causes kernel panic. Following patch fixes it by
using standard API to get net-device stats.

---8<---
Unable to handle kernel paging request at virtual address 766b4008
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: vport_vxlan vxlan ip6_udp_tunnel udp_tunnel tun bridge stp llc openvswitch ipv6
CPU: 7 PID: 1108 Comm: ovs-vswitchd Not tainted 4.3.0-rc3+ #82
PC is at ovs_vport_get_stats+0x150/0x1f8 [openvswitch]
<snip>
Call trace:
 [<ffffffbffc0859f8>] ovs_vport_get_stats+0x150/0x1f8 [openvswitch]
 [<ffffffbffc07cdb0>] ovs_vport_cmd_fill_info+0x140/0x1e0 [openvswitch]
 [<ffffffbffc07cf0c>] ovs_vport_cmd_dump+0xbc/0x138 [openvswitch]
 [<ffffffc00045a5ac>] netlink_dump+0xb8/0x258
 [<ffffffc00045ace0>] __netlink_dump_start+0x120/0x178
 [<ffffffc00045dd9c>] genl_family_rcv_msg+0x2d4/0x308
 [<ffffffc00045de58>] genl_rcv_msg+0x88/0xc4
 [<ffffffc00045cf24>] netlink_rcv_skb+0xd4/0x100
 [<ffffffc00045dab0>] genl_rcv+0x30/0x48
 [<ffffffc00045c830>] netlink_unicast+0x154/0x200
 [<ffffffc00045cc9c>] netlink_sendmsg+0x308/0x364
 [<ffffffc00041e10c>] sock_sendmsg+0x14/0x2c
 [<ffffffc000420d58>] SyS_sendto+0xbc/0xf0
Code: aa1603e1 f94037a4 aa1303e2 aa1703e0 (f9400465)
Reported-by: Tomasz Sawicki <tomasz.sawicki@objectiveintegration.uk>
Fixes: 8c876639 ("openvswitch: Remove vport stats.")
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without this patch, if the only instructions using r_X are of the
BPF_LD | BPF_IND type, r_X would not be reset to 0, using whatever
value was there when entering the jited code. With this patch, r_X
will be correctly marked as used so it will be reset to 0 in the
prologue code.

This fix also makes the test "LD_IND byte default X" pass in the
test_bpf module when the ARM JIT is enabled.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

When openvswitch tries allocate memory from offline numa node 0:
stats = kmem_cache_alloc_node(flow_stats_cache, GFP_KERNEL | __GFP_ZERO, 0)
It catches VM_BUG_ON(nid < 0 || nid >= MAX_NUMNODES || !node_online(nid))
[ replaced with VM_WARN_ON(!node_online(nid)) recently ] in linux/gfp.h
This patch disables numa affinity in this case.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When sockets have a native eBPF program attached through
setsockopt(sk, SOL_SOCKET, SO_ATTACH_BPF, ...), and then try to
dump these over getsockopt(sk, SOL_SOCKET, SO_GET_FILTER, ...),
the following panic appears:

  [49904.178642] BUG: unable to handle kernel NULL pointer dereference at (null)
  [49904.178762] IP: [<ffffffff81610fd9>] sk_get_filter+0x39/0x90
  [49904.182000] PGD 86fc9067 PUD 531a1067 PMD 0
  [49904.185196] Oops: 0000 [#1] SMP
  [...]
  [49904.224677] Call Trace:
  [49904.226090]  [<ffffffff815e3d49>] sock_getsockopt+0x319/0x740
  [49904.227535]  [<ffffffff812f59e3>] ? sock_has_perm+0x63/0x70
  [49904.228953]  [<ffffffff815e2fc8>] ? release_sock+0x108/0x150
  [49904.230380]  [<ffffffff812f5a43>] ? selinux_socket_getsockopt+0x23/0x30
  [49904.231788]  [<ffffffff815dff36>] SyS_getsockopt+0xa6/0xc0
  [49904.233267]  [<ffffffff8171b9ae>] entry_SYSCALL_64_fastpath+0x12/0x71

The underlying issue is the very same as in commit b382c086
("sock, diag: fix panic in sock_diag_put_filterinfo"), that is,
native eBPF programs don't store an original program since this
is only needed in cBPF ones.

However, sk_get_filter() wasn't updated to test for this at the
time when eBPF could be attached. Just throw an error to the user
to indicate that eBPF cannot be dumped over this interface.
That way, it can also be known that a program _is_ attached (as
opposed to just return 0), and a different (future) method needs
to be consulted for a dump.

Fixes: 89aa0758 ("net: sock: allow eBPF programs to be attached to sockets")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>