- 16 Nov, 2012 24 commits
-
-
Arend van Spriel authored
The IF event need special care. It can be either an ADD, DEL, or CHANGE. For an ADD we need to call brcmf_add_if() before the event handler call. Upon a DEL we need to call brcmf_del_if() after the event handler call. CHANGE does not require special attention. Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
Franky Lin <frankyl@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
Firmware fires IF event to add the primary interface but that is already created in the driver. Reviewed-by:
-
Arend van Spriel authored
Replaced <linux/unaligned/access_ok.h> by <asm/unaligned.h> to make it work on ARM and other architectures. Reviewed-by:
-
Hante Meuleman authored
brcmf_fweh_detach can be called while ifp is already NULL, due to init error. Fix NULL pointer access by checking ifp. Reviewed-by:
-
Arend van Spriel authored
The mac_addr field in ifp object is always valid so no need to validate. Reviewed-by:
-
Arend van Spriel authored
The function brcmf_add_if() is called with mac address set to NULL for the primary interface. When handling IF ADD events the firmware provides a address mask in the event to derive its mac address from the primary mac address. Rename the parameter and use it as a mask. Reviewed-by:
-
Arend van Spriel authored
Testing revealed the IF ADD event contains the interface index of the new interface. This would result in a NULL pointer access when handling the event. Reviewed-by:
-
Arend van Spriel authored
virtual netdevice interface like P2P client and GO need different callbacks for .open and .down. This patch adds those. Reviewed-by:
-
Arend van Spriel authored
The brcmf_add_if() function had a struct device as parameter to accomodate the bus specific code to use this function. The driver has been reworked so the bus specific code does not need this function. Better replace the parameter with a more specific driver object, ie. struct brcmf_pub. Reviewed-by:
-
Hante Meuleman authored
Add support for usb suspend/resume. Reviewed-by:
-
Hante Meuleman authored
Clean code related to firmware download routines. Remove obsolete delay and increase delay after reset command. Reviewed-by:
-
Arend van Spriel authored
Handling of firmware event has been reworked into a seperate code file. The change is needed as firmware event can be received in interrupt context. Decoupling of the event handling has been lowered to allow event processing to sleep. Reviewed-by:
-
Dan Carpenter authored
'|' has higher precedence than ?:. Since AR5K_PHY_TURBO_MODE is 0x1 and "AR5K_PHY_TURBO_MODE | (ah->ah_radio == AR5K_RF2425)" is true then we always set turbo to zero. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Syam Sidhardhan authored
Simplify the code by make use of module_platform_driver macro. Signed-off-by:
Syam Sidhardhan <s.syam@samsung.com> Signed-off-by:
-
Sujith Manoharan authored
The workaround for ASPM/L0s is needed only for AR9485 1.0, which was never sold and is not supported by ath9k. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Rajkumar Manoharan authored
An issue is reported in AR9462 & AR9565 that NF_cal_not_done is not observed when HW peak detector calibration is disabled. At that state, the HW is stuck at NF calibration which prevents tx output. The root cause is wrong peak detector offset calibrated by HW. To resolve this issue, peak detector calibration is done manually by SW for AR9462 and AR9565. Signed-off-by:
Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by:
-
Yogesh Ashok Powar authored
The firmware supports 8 macid's corresponding to 8 BSS that can be created in an MBSS environment. Currently, BASTREAM commands were always sent with macid 0. This macid is used to configure the hardware ampdu registers with appropriate BSS address in an MBSS environment. This mac address is used by the hardware for various ampdu related requirements e.g. source address in BAR generation, BA interpretation e.t.c. Using invalid macid results in this mac address not getting appropriately configured in the hardware which results in issues during ampdu traffic. Fix this by sending the BASTREAM commands with appropriate macid. Signed-off-by:
Nishant Sarmukadam <nishants@marvell.com> Signed-off-by:
Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by:
-
Piotr Haber authored
Offset for temperature compensation values is wrong in ssb SPROMv8 map. Reviewed-by:
Piotr Haber <phaber@broadcom.com> Signed-off-by:
-
Zefir Kurtisi authored
Add 5% width tolerance for radar patterns defined by ETSI. Signed-off-by:
Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by:
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-nextJohn W. Linville authored
Conflicts: drivers/net/wireless/iwlwifi/pcie/trans.c
-
-
Kalle Valo authored
As ath6kl firmware can't do intersections the driver should only listen to regdom changes from cellular base stations, all other requests need to be refused. Signed-off-by:Kalle Valo <kvalo@qca.qualcomm.com>
-
- 14 Nov, 2012 16 commits
-
-
Nishant Sarmukadam authored
Set tx packet timestamp to 0 in following scenarios:- - All packets in STA mode - Mgmt packets in AP mode - Eapol packets in AP mode In STA mode, this field is unused in the firmware. In AP mode, we should not be expiring mgmt and eapol frames. Setting timestamp to 0 will ensure that. Signed-off-by:
-
Nishant Sarmukadam authored
This can cause issues when clients try to connect when the traffic is heavy Signed-off-by:
-
Nishant Sarmukadam authored
We should unmap the DMA address in the error path, else it causes resource leaks. Fix this. Signed-off-by:
-
Yogesh Ashok Powar authored
We have 6.5 Mbps is minimum rate of the link as the criterion for creation of BA. Although we check this before creating the BA stream, by the time amdpu_action is called from the workqueue, the link can get affected in the meantime. Hence, add an additional check in amdpu_action. Signed-off-by:
-
Yogesh Ashok Powar authored
AP mode support upto 8 interfaces. Defining it using iface_combinations Signed-off-by:
-
Bing Zhao authored
ksdioirqd has higher priority than kworker. Process RX packets in SDIO IRQ thread (ksdioirqd/mmcX) directly instead of deferring the work to kworker to avoid the extra latency. This improves TCP throughput 15~20% on an ARM platform with SDIO 2.0 controller. Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Arend van Spriel authored
Firmware events are passed to wl_cfg80211 module associated with the primary net device. With virtual interface support events can be received for different interfaces, ie. struct brcmf_if instances. Pass it in the event to determine appropriate net device associated with the event. Reviewed-by:
-
Hante Meuleman authored
Add USB log level and update and add log messages in usb module. Reviewed-by:
-
Hante Meuleman authored
brcmf_netdev_stop shall first check bus_if status before bringing down cfg80211. brcmf_detach shall first check if driver is allocated. Reviewed-by:
-
Hante Meuleman authored
brcmf_netdev_start_xmit and brcmf_fil_cmd_data are checking bus state for down. These functions should check for data state. Reviewed-by:
-
Hante Meuleman authored
when brcmf_cfg80211_del_key was called with out of range key index then firmware would return error. Checking was added to brcmf_cfg80211_del_key to immediately return error. Reviewed-by:
-
Arend van Spriel authored
This fixes a build regression for x86_64 target that showed up in 3.7-rc1 due to: commit 1a873342 Author: Hante Meuleman <meuleman@broadcom.com> Date: Thu Sep 27 14:17:54 2012 +0200 brcmfmac: add hostap supoort. Reported-by:
Yuanhan Liu <yuanhan.liu@intel.com> Reported-by:
Geert Uytterhoeven <geert@linux-m68k.org> Reported-by:
Randy Dunlap <rdunlap@infradead.org> Reviewed-by:
-
Franky Lin authored
Use int instead of bool as the return type of function brcmf_sdio_hdparser to explicitly describe error returns. Signed-off-by:
-
Franky Lin authored
brcmf_sdbrcm_wait_for_event is now a one line function and only used by brcmf_sdbrcm_bus_txctl. Intergrate the function call wait_event_interruptible_timeout into brcmf_sdbrcm_bus_txctl. Signed-off-by:
-
Franky Lin authored
Semaphore sdsem is used to protect consecutive memory access through SDIO bus. Same functionality is provided by sdio_claim_host/ sdio_release_host interface as well. Replace sdsem with sdio_claim_host. Signed-off-by:
-
Franky Lin authored
Semaphore sdsem which protects consecutive SDIO bus access is used to lock down unnecessary wide range. Decrease the locking range provides the capability of parallel processing. Signed-off-by:
-
