A HWMON device is only registered is the SFP module supports the
diagnostic page and is complient to SFF8472. Don't unconditionally
unregister the hwmon device when the SFP module is remove, otherwise
we access data structures which don't exist.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 1323061a ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clang warns when one enumerated type is implicitly converted to another.

drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1713:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
                cm_info->ip_version = TCP_IPV4;
                                    ~ ^~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1733:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
                cm_info->ip_version = TCP_IPV6;
                                    ~ ^~~~~~~~
2 warnings generated.

Use the appropriate values from the expected type, qed_tcp_ip_version:

TCP_IPV4 = QED_TCP_IPV4 = 0
TCP_IPV6 = QED_TCP_IPV6 = 1

Link: https://github.com/ClangBuiltLinux/linux/issues/125Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clang warns when a constant is used in a boolean context as it thinks a
bitwise operation may have been intended.

drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: warning: use of logical
'&&' with constant operand [-Wconstant-logical-operand]
        if (!p_iov->b_pre_fp_hsi &&
                                 ^
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: use '&' for a
bitwise operation
        if (!p_iov->b_pre_fp_hsi &&
                                 ^~
                                 &
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: remove constant
to silence this warning
        if (!p_iov->b_pre_fp_hsi &&
                                ~^~
1 warning generated.

This has been here since commit 1fe614d1 ("qed: Relax VF firmware
requirements") and I am not entirely sure why since 0 isn't a special
case. Just remove the statement causing Clang to warn since it isn't
required.

Link: https://github.com/ClangBuiltLinux/linux/issues/126Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzkaller reported this on a slightly older kernel but it's still
applicable to the current kernel -

======================================================
WARNING: possible circular locking dependency detected
4.18.0-next-20180823+ #46 Not tainted
------------------------------------------------------
syz-executor4/26841 is trying to acquire lock:
00000000dd41ef48 ((wq_completion)bond_dev->name){+.+.}, at: flush_workqueue+0x2db/0x1e10 kernel/workqueue.c:2652

but task is already holding lock:
00000000768ab431 (rtnl_mutex){+.+.}, at: rtnl_lock net/core/rtnetlink.c:77 [inline]
00000000768ab431 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x412/0xc30 net/core/rtnetlink.c:4708

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (rtnl_mutex){+.+.}:
       __mutex_lock_common kernel/locking/mutex.c:925 [inline]
       __mutex_lock+0x171/0x1700 kernel/locking/mutex.c:1073
       mutex_lock_nested+0x16/0x20 kernel/locking/mutex.c:1088
       rtnl_lock+0x17/0x20 net/core/rtnetlink.c:77
       bond_netdev_notify drivers/net/bonding/bond_main.c:1310 [inline]
       bond_netdev_notify_work+0x44/0xd0 drivers/net/bonding/bond_main.c:1320
       process_one_work+0xc73/0x1aa0 kernel/workqueue.c:2153
       worker_thread+0x189/0x13c0 kernel/workqueue.c:2296
       kthread+0x35a/0x420 kernel/kthread.c:246
       ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415

-> #1 ((work_completion)(&(&nnw->work)->work)){+.+.}:
       process_one_work+0xc0b/0x1aa0 kernel/workqueue.c:2129
       worker_thread+0x189/0x13c0 kernel/workqueue.c:2296
       kthread+0x35a/0x420 kernel/kthread.c:246
       ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415

-> #0 ((wq_completion)bond_dev->name){+.+.}:
       lock_acquire+0x1e4/0x4f0 kernel/locking/lockdep.c:3901
       flush_workqueue+0x30a/0x1e10 kernel/workqueue.c:2655
       drain_workqueue+0x2a9/0x640 kernel/workqueue.c:2820
       destroy_workqueue+0xc6/0x9d0 kernel/workqueue.c:4155
       __alloc_workqueue_key+0xef9/0x1190 kernel/workqueue.c:4138
       bond_init+0x269/0x940 drivers/net/bonding/bond_main.c:4734
       register_netdevice+0x337/0x1100 net/core/dev.c:8410
       bond_newlink+0x49/0xa0 drivers/net/bonding/bond_netlink.c:453
       rtnl_newlink+0xef4/0x1d50 net/core/rtnetlink.c:3099
       rtnetlink_rcv_msg+0x46e/0xc30 net/core/rtnetlink.c:4711
       netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2454
       rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4729
       netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
       netlink_unicast+0x5a0/0x760 net/netlink/af_netlink.c:1343
       netlink_sendmsg+0xa18/0xfc0 net/netlink/af_netlink.c:1908
       sock_sendmsg_nosec net/socket.c:622 [inline]
       sock_sendmsg+0xd5/0x120 net/socket.c:632
       ___sys_sendmsg+0x7fd/0x930 net/socket.c:2115
       __sys_sendmsg+0x11d/0x290 net/socket.c:2153
       __do_sys_sendmsg net/socket.c:2162 [inline]
       __se_sys_sendmsg net/socket.c:2160 [inline]
       __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2160
       do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
       entry_SYSCALL_64_after_hwframe+0x49/0xbe

other info that might help us debug this:

Chain exists of:
  (wq_completion)bond_dev->name --> (work_completion)(&(&nnw->work)->work) --> rtnl_mutex

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(rtnl_mutex);
                               lock((work_completion)(&(&nnw->work)->work));
                               lock(rtnl_mutex);
  lock((wq_completion)bond_dev->name);

 *** DEADLOCK ***

1 lock held by syz-executor4/26841:

stack backtrace:
CPU: 1 PID: 26841 Comm: syz-executor4 Not tainted 4.18.0-next-20180823+ #46
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
 print_circular_bug.isra.34.cold.55+0x1bd/0x27d kernel/locking/lockdep.c:1222
 check_prev_add kernel/locking/lockdep.c:1862 [inline]
 check_prevs_add kernel/locking/lockdep.c:1975 [inline]
 validate_chain kernel/locking/lockdep.c:2416 [inline]
 __lock_acquire+0x3449/0x5020 kernel/locking/lockdep.c:3412
 lock_acquire+0x1e4/0x4f0 kernel/locking/lockdep.c:3901
 flush_workqueue+0x30a/0x1e10 kernel/workqueue.c:2655
 drain_workqueue+0x2a9/0x640 kernel/workqueue.c:2820
 destroy_workqueue+0xc6/0x9d0 kernel/workqueue.c:4155
 __alloc_workqueue_key+0xef9/0x1190 kernel/workqueue.c:4138
 bond_init+0x269/0x940 drivers/net/bonding/bond_main.c:4734
 register_netdevice+0x337/0x1100 net/core/dev.c:8410
 bond_newlink+0x49/0xa0 drivers/net/bonding/bond_netlink.c:453
 rtnl_newlink+0xef4/0x1d50 net/core/rtnetlink.c:3099
 rtnetlink_rcv_msg+0x46e/0xc30 net/core/rtnetlink.c:4711
 netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2454
 rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4729
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x5a0/0x760 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0xa18/0xfc0 net/netlink/af_netlink.c:1908
 sock_sendmsg_nosec net/socket.c:622 [inline]
 sock_sendmsg+0xd5/0x120 net/socket.c:632
 ___sys_sendmsg+0x7fd/0x930 net/socket.c:2115
 __sys_sendmsg+0x11d/0x290 net/socket.c:2153
 __do_sys_sendmsg net/socket.c:2162 [inline]
 __se_sys_sendmsg net/socket.c:2160 [inline]
 __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2160
 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457089
Code: fd b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f2df20a5c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f2df20a66d4 RCX: 0000000000457089
RDX: 0000000000000000 RSI: 0000000020000180 RDI: 0000000000000003
RBP: 0000000000930140 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000004d40b8 R14: 00000000004c8ad8 R15: 0000000000000001
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b89f04c6 ("bonding: deliver link-local packets with
skb->dev set to link that packets arrived on") changed the behavior
of how link-local-multicast packets are processed. The change in
the behavior broke some legacy use cases where these packets are
expected to arrive on bonding master device also.

This patch passes the packet to the stack with the link it arrived
on as well as passes to the bonding-master device to preserve the
legacy use case.

Fixes: b89f04c6 ("bonding: deliver link-local packets with skb->dev set to link that packets arrived on")
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clang warns when one enumerated type is implicitly converted to another.

drivers/net/ethernet/qlogic/qed/qed_roce.c:153:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
                flavor = ROCE_V2_IPV6;
                       ~ ^~~~~~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_roce.c:156:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
                flavor = MAX_ROCE_MODE;
                       ~ ^~~~~~~~~~~~~
2 warnings generated.

Use the appropriate values from the expected type, roce_flavor:

ROCE_V2_IPV6 = RROCE_IPV6 = 2
MAX_ROCE_MODE = MAX_ROCE_FLAVOR = 3

While we're add it, ditch the local variable flavor, we can just return
the value directly from the switch statement.

Link: https://github.com/ClangBuiltLinux/linux/issues/125Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clang complains when one enumerated type is implicitly converted to
another.

drivers/net/ethernet/qlogic/qed/qed_vf.c:686:6: warning: implicit
conversion from enumeration type 'enum qed_tunn_mode' to different
enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
                                 QED_MODE_L2GENEVE_TUNN,
                                 ^~~~~~~~~~~~~~~~~~~~~~

Update mask's parameter to expect qed_tunn_mode, which is what was
intended.

Link: https://github.com/ClangBuiltLinux/linux/issues/125Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clang warns when one enumerated type is implicitly converted to another.

drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:163:25: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
        p_tun->vxlan.tun_cls = type;
                             ~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:165:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
        p_tun->l2_gre.tun_cls = type;
                              ~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:167:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
        p_tun->ip_gre.tun_cls = type;
                              ~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:169:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
        p_tun->l2_geneve.tun_cls = type;
                                 ~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:171:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
        p_tun->ip_geneve.tun_cls = type;
                                 ~ ^~~~
5 warnings generated.

Avoid this by changing type to an int.

Link: https://github.com/ClangBuiltLinux/linux/issues/125Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in ms_to_errno array of error messages
and remove confusing "not" from the error text since the error code
refers to an uninitialized error code.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in DP_VERBOSE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: fix WoL handling when suspending the PHY

phy_suspend doesn't always recognize that WoL is enabled and therefore
suspends the PHY when it should not. First idea to address the issue
was to reuse checks used in mdio_bus_phy_may_suspend which check
whether relevant devices are wakeup-enabled.
Florian raised some concerns because drivers may enable wakeup even if
WoL isn't enabled (e.g. certain USB network drivers).

The new approach focuses on reducing the risk to break existing stuff.
We add a flag wol_enabled to struct net_device which is set in
ethtool_set_wol(). Then this flag is checked in phy_suspend().
This doesn't cover 100% of the cases yet (e.g. if WoL is enabled w/o
explicit configuration), but it covers the most relevant cases with
very little risk of regressions.

v2:
- Fix a typo
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Core of the problem is that phy_suspend() suspends the PHY when it
should not because of WoL. phy_suspend() checks for WoL already, but
this works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.

This patch uses new member wol_enabled of struct net_device as
additional criteria in the check when not to suspend the PHY because
of WoL.

Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.

Fixes: f1e911d5 ("r8169: add basic phylib support")
Fixes: e8cfd9d6 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add flag wol_enabled to struct net_device indicating whether
Wake-on-LAN is enabled. As first user phy_suspend() will use it to
decide whether PHY can be suspended or not.

Fixes: f1e911d5 ("r8169: add basic phylib support")
Fixes: e8cfd9d6 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit e0511f6c.

I commited the wrong version of these changes.
Signed-off-by: David S. Miller <davem@davemloft.net>

Actually there's nothing wrong with the two changes marked as "Fixes",
they just revealed a problem which has been existing before.
After having switched r8169 to phylib it was reported that WoL from
shutdown doesn't work any longer (WoL from suspend isn't affected).
Reason is that during shutdown phy_disconnect()->phy_detach()->
phy_suspend() is called.
A similar issue occurs when the phylib state machine calls
phy_suspend() when handling state PHY_HALTED.

Core of the problem is that phy_suspend() suspends the PHY when it
should not due to WoL. phy_suspend() checks for WoL already, but this
works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.

phylib knows about this and handles it in mdio_bus_phy_may_suspend(),
but that's used only when suspending the system, not in other cases
like shutdown.

Therefore factor out the relevant check from
mdio_bus_phy_may_suspend() to a new function phy_may_suspend() and
use it in phy_suspend().

Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.

Fixes: f1e911d5 ("r8169: add basic phylib support")
Fixes: e8cfd9d6 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The change to move metrics from the dst to rt6_info moved the call
to ip6_convert_metrics from ip6_route_add to ip6_route_info_create. In
doing so it makes the call in ip6_route_info_append redundant and
actually leaks the metrics installed as part of the ip6_route_info_create.
Remove the now unnecessary call.

Fixes: d4ead6b3 ("net/ipv6: move metrics from dst to rt6_info")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In tipc_link_reset() we copy the wakeup queue to input queue using
skb_queue_splice_init(link->wakeupq, link->inputq).
This is performed without holding any locks. The lists might be
simultaneously be accessed by other cpu threads in tipc_sk_rcv(),
something leading to to random missing packets.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we detect that under lying carrier detects errors and goes down,
we reset the bearer.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case of implicit connect message with data > 1K, the flow
control accounting is incorrect. At this state, the socket does not
know the peer nodes capability and falls back to legacy flow control
by return 1, however the receiver of this message will perform the
new block accounting. This leads to a slack and eventually traffic
disturbance.

In this commit, we perform tipc_node_get_capabilities() at implicit
connect and perform accounting based on the peer's capability.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If SMMU is on, there is more likely that skb_shinfo(skb)->frags[i]
can not send by a single BD. when this happen, the
hns_nic_net_xmit_hw function map the whole data in a frags using
skb_frag_dma_map, but unmap each BD' data individually when tx is
done, which causes problem when SMMU is on.

This patch fixes this problem by ummapping the whole data in a
frags when tx is done.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jan Beulich says:

====================
xen-netback: hash mapping handling adjustments

First and foremost the fix for XSA-270. On top of that further changes
which looked desirable to me while investigating that XSA.

1: fix input validation in xenvif_set_hash_mapping()
2: validate queue numbers in xenvif_set_hash_mapping()
3: handle page straddling in xenvif_set_hash_mapping()
====================
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no guarantee that the mapping array doesn't cross a page
boundary. Use a second grant copy operation if necessary.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Checking them before the grant copy means nothing as to the validity of
the incoming request. As we shouldn't make the new data live before
having validated it, introduce a second instance of the mapping array.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both len and off are frontend specified values, so we need to make
sure there's no overflow when adding the two for the bounds check. We
also want to avoid undefined behavior and hence use off to index into
->hash.mapping[] only after bounds checking. This at the same time
allows to take care of not applying off twice for the bounds checking
against vif->num_queues.

It is also insufficient to bounds check copy_op.len, as this is len
truncated to 16 bits.

This is XSA-270 / CVE-2018-15471.
Reported-by: Felix Wilhelm <fwilhelm@google.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Tested-by: Paul Durrant <paul.durrant@citrix.com>
Cc: stable@vger.kernel.org [4.7 onwards]
Signed-off-by: David S. Miller <davem@davemloft.net>

Clear ADDR64 dma bit in DMACFG register in case that HW_DMA_CAP_64B is
not detected on 64bit system.
The issue was observed when bootloader(u-boot) does not check macb
feature at DCFG6 register (DAW64_OFFSET) and enabling 64bit dma support
by default. Then macb driver is reading DMACFG register back and only
adding 64bit dma configuration but not cleaning it out.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

James writes:
  "SCSI fixes on 20180925

   Nine obvious bug fixes mostly in individual drivers.  The target fix
   is of particular importance because it's CVE related."

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: sd: don't crash the host on invalid commands
  scsi: ipr: System hung while dlpar adding primary ipr adapter back
  scsi: target: iscsi: Use bin2hex instead of a re-implementation
  scsi: target: iscsi: Use hex2bin instead of a re-implementation
  scsi: lpfc: Synchronize access to remoteport via rport
  scsi: ufs: Disable blk-mq for now
  scsi: sd: Contribute to randomness when running rotational device
  scsi: ibmvscsis: Ensure partition name is properly NUL terminated
  scsi: ibmvscsis: Fix a stringop-overflow warning

I wrote:
  "USB fixes for 4.19-rc6

   Here are some small USB core and driver fixes for reported issues for
   4.19-rc6.

   The most visible is the oops fix for when the USB core is built into the
   kernel that is present in 4.18.  Turns out not many people actually do
   that so it went unnoticed for a while.  The rest is some tiny typec,
   musb, and other core fixes.

   All have been in linux-next with no reported issues."

* tag 'usb-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: mux: Take care of driver module reference counting
  usb: core: safely deal with the dynamic quirk lists
  usb: roles: Take care of driver module reference counting
  USB: handle NULL config in usb_find_alt_setting()
  USB: fix error handling in usb_driver_claim_interface()
  USB: remove LPM management from usb_driver_claim_interface()
  USB: usbdevfs: restore warning for nonsensical flags
  USB: usbdevfs: sanitize flags more
  Revert "usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()"
  usb: musb: dsps: do not disable CPPI41 irq in driver teardown

I wrote:
  "TTY/Serial driver fixes for 4.19-rc6

   Here are a number of small tty and serial driver fixes for reported
   issues for 4.19-rc6.

   One should hopefully resolve a much-reported issue that syzbot has found
   in the tty layer.  Although there are still more issues there, getting
   this fixed is nice to see finally happen.

   All of these have been in linux-next for a while with no reported
   issues."

* tag 'tty-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: imx: restore handshaking irq for imx1
  tty: vt_ioctl: fix potential Spectre v1
  tty: Drop tty->count on tty_reopen() failure
  serial: cpm_uart: return immediately from console poll
  tty: serial: lpuart: avoid leaking struct tty_struct
  serial: mvebu-uart: Fix reporting of effective CSIZE to userspace

Greg (well I), wrote:
  "Char/Misc driver fixes for 4.19-rc6

   Here are some soundwire and intel_th (tracing) driver fixes for some
   reported issues.

   All of these have been in linux-next for a week with no reported issues."

* tag 'char-misc-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  intel_th: pci: Add Ice Lake PCH support
  intel_th: Fix resource handling for ACPI glue layer
  intel_th: Fix device removal logic
  soundwire: Fix acquiring bus lock twice during master release
  soundwire: Fix incorrect exit after configuring stream
  soundwire: Fix duplicate stream state assignment

This changes UAPI, breaking iwd and libell:

  ell/key.c: In function 'kernel_dh_compute':
  ell/key.c:205:38: error: 'struct keyctl_dh_params' has no member named 'private'; did you mean 'dh_private'?
    struct keyctl_dh_params params = { .private = private,
                                        ^~~~~~~
                                        dh_private

This reverts commit 8a2336e5.

Fixes: 8a2336e5 ("uapi/linux/keyctl.h: don't use C++ reserved keyword as a struct member name")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Randy Dunlap <rdunlap@infradead.org>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Stephan Mueller <smueller@chronox.de>
cc: James Morris <jmorris@namei.org>
cc: "Serge E. Hallyn" <serge@hallyn.com>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: Linus Torvalds <torvalds@linux-foundation.org>
cc: <stable@vger.kernel.org>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Dave writes:
  "Networking fixes:

  1) Fix multiqueue handling of coalesce timer in stmmac, from Jose
     Abreu.

   2) Fix memory corruption in NFC, from Suren Baghdasaryan.

   3) Don't write reserved bits in ravb driver, from Kazuya Mizuguchi.

   4) SMC bug fixes from Karsten Graul, YueHaibing, and Ursula Braun.

   5) Fix TX done race in mvpp2, from Antoine Tenart.

   6) ipv6 metrics leak, from Wei Wang.

   7) Adjust firmware version requirements in mlxsw, from Petr Machata.

   8) Fix autonegotiation on resume in r8169, from Heiner Kallweit.

   9) Fixed missing entries when dumping /proc/net/if_inet6, from Jeff
      Barnhill.

   10) Fix double free in devlink, from Dan Carpenter.

   11) Fix ethtool regression from UFO feature removal, from Maciej
       Żenczykowski.

   12) Fix drivers that have a ndo_poll_controller() that captures the
       cpu entirely on loaded hosts by trying to drain all rx and tx
       queues, from Eric Dumazet.

   13) Fix memory corruption with jumbo frames in aquantia driver, from
       Friedemann Gerold."

* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (79 commits)
  net: mvneta: fix the remaining Rx descriptor unmapping issues
  ip_tunnel: be careful when accessing the inner header
  mpls: allow routes on ip6gre devices
  net: aquantia: memory corruption on jumbo frames
  tun: remove ndo_poll_controller
  nfp: remove ndo_poll_controller
  bnxt: remove ndo_poll_controller
  bnx2x: remove ndo_poll_controller
  mlx5: remove ndo_poll_controller
  mlx4: remove ndo_poll_controller
  i40evf: remove ndo_poll_controller
  ice: remove ndo_poll_controller
  igb: remove ndo_poll_controller
  ixgb: remove ndo_poll_controller
  fm10k: remove ndo_poll_controller
  ixgbevf: remove ndo_poll_controller
  ixgbe: remove ndo_poll_controller
  bonding: use netpoll_poll_dev() helper
  netpoll: make ndo_poll_controller() optional
  rds: Fix build regression.
  ...

With CONFIG_DMA_API_DEBUG enabled we get DMA unmapping warning in
various places of the mvneta driver, for example when putting down an
interface while traffic is passing through.

The issue is when using s/w buffer management, the Rx buffers are mapped
using dma_map_page but unmapped with dma_unmap_single. This patch fixes
this by using the right unmapping function.

Fixes: 562e2f46 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cong noted that we need the same checks introduced by commit 76c0ddd8
("ip6_tunnel: be careful when accessing the inner header")
even for ipv4 tunnels.

Fixes: c5441932 ("GRE: Refactor GRE tunneling code.")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Summary:

This appears to be necessary and sufficient change to enable `MPLS` on
`ip6gre` tunnels (RFC4023).

This diff allows IP6GRE devices to be recognized by MPLS kernel module
and hence user can configure interface to accept packets with mpls
headers as well setup mpls routes on them.

Test Plan:

Test plan consists of multiple containers connected via GRE-V6 tunnel.
Then carrying out testing steps as below.

- Carry out necessary sysctl settings on all containers

```
sysctl -w net.mpls.platform_labels=65536
sysctl -w net.mpls.ip_ttl_propagate=1
sysctl -w net.mpls.conf.lo.input=1
```

- Establish IP6GRE tunnels

```
ip -6 tunnel add name if_1_2_1 mode ip6gre \
  local 2401:db00:21:6048:feed:0::1 \
  remote 2401:db00:21:6048:feed:0::2 key 1
ip link set dev if_1_2_1 up
sysctl -w net.mpls.conf.if_1_2_1.input=1
ip -4 addr add 169.254.0.2/31 dev if_1_2_1 scope link

ip -6 tunnel add name if_1_3_1 mode ip6gre \
  local 2401:db00:21:6048:feed:0::1 \
  remote 2401:db00:21:6048:feed:0::3 key 1
ip link set dev if_1_3_1 up
sysctl -w net.mpls.conf.if_1_3_1.input=1
ip -4 addr add 169.254.0.4/31 dev if_1_3_1 scope link
```

- Install MPLS encap rules on node-1 towards node-2

```
ip route add 192.168.0.11/32 nexthop encap mpls 32/64 \
  via inet 169.254.0.3 dev if_1_2_1
```

- Install MPLS forwarding rules on node-2 and node-3
```
// node2
ip -f mpls route add 32 via inet 169.254.0.7 dev if_2_4_1

// node3
ip -f mpls route add 64 via inet 169.254.0.12 dev if_4_3_1
```

- Ping 192.168.0.11 (node4) from 192.168.0.1 (node1) (where routing
  towards 192.168.0.1 is via IP route directly towards node1 from node4)
```
ping 192.168.0.11
```

- tcpdump on interface to capture ping packets wrapped within MPLS
  header which inturn wrapped within IP6GRE header

```
16:43:41.121073 IP6
  2401:db00:21:6048:feed::1 > 2401:db00:21:6048:feed::2:
  DSTOPT GREv0, key=0x1, length 100:
  MPLS (label 32, exp 0, ttl 255) (label 64, exp 0, [S], ttl 255)
  IP 192.168.0.1 > 192.168.0.11:
  ICMP echo request, id 1208, seq 45, length 64

0x0000:  6000 2cdb 006c 3c3f 2401 db00 0021 6048  `.,..l<?$....!`H
0x0010:  feed 0000 0000 0001 2401 db00 0021 6048  ........$....!`H
0x0020:  feed 0000 0000 0002 2f00 0401 0401 0100  ......../.......
0x0030:  2000 8847 0000 0001 0002 00ff 0004 01ff  ...G............
0x0040:  4500 0054 3280 4000 ff01 c7cb c0a8 0001  E..T2.@.........
0x0050:  c0a8 000b 0800 a8d7 04b8 002d 2d3c a05b  ...........--<.[
0x0060:  0000 0000 bcd8 0100 0000 0000 1011 1213  ................
0x0070:  1415 1617 1819 1a1b 1c1d 1e1f 2021 2223  .............!"#
0x0080:  2425 2627 2829 2a2b 2c2d 2e2f 3031 3233  $%&'()*+,-./0123
0x0090:  3435 3637                                4567
```
Signed-off-by: Saif Hasan <has@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-09-24

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Several fixes for BPF sockmap to only allow sockets being attached in
   ESTABLISHED state, from John.

2) Fix up the license to LGPL/BSD for the libc compat header which contains
   fallback helpers that libbpf and bpftool is using, from Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Mauro briefly writes:
  "media fixes for v4.19-rc5

   some drivers and Kbuild fixes"

* tag 'media/v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  media: platform: fix cros-ec-cec build error
  media: staging/media/mt9t031/Kconfig: remove bogus entry
  media: i2c: mt9v111: Fix v4l2-ctrl error handling
  media: camss: add missing includes
  media: camss: Use managed memory allocations
  media: camss: mark PM functions as __maybe_unused
  media: af9035: prevent buffer overflow on write
  media: video_function_calls.rst: drop obsolete video-set-attributes reference

This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.

Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.

In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.

The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:

    sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
          / Raw(RandString(size=(4096-40))), iface="enp1s0")

Fixes: 018423e9 ("net: ethernet: aquantia: Add ring support code")
Reported-by: Friedemann Gerold <f.gerold@b-c-s.de>
Reported-by: Michael Rauch <michael@rauch.be>
Signed-off-by: Friedemann Gerold <f.gerold@b-c-s.de>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
netpoll: avoid capture effects for NAPI drivers

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC).

This capture, showing one ksoftirqd eating all cycles
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller() :

Most NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev()
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.

This patch series take care of the first round, we will
handle other drivers in future rounds.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

tun uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

nfp uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>