When the GMBUS based i2c transfer times out, we try to fall back to
bit-banging and retry the operation that way. However if the bit-banging
attempt also fails, we should probably go back to the GMBUS method for
the next attempt. Maybe there simply wasn't anyone one the bus at this
time.

There's also a bit of a mess going on with the force_bit handling.
It's supposed to be a ref count actually, and it is as far as
intel_gmbus_force_bit() is concerned. But it's treated as just a
flag by the timeout based bit-banging fallback. I suppose that's
fine since we should never end up in the timeout fallback case
if force_bit was already non-zero. However now that we want to restore
things back to where they were after the bit-banging attempt failed,
we're going to have to do things a bit differently to avoid clobbering
the force_bit count as set up by intel_gmbus_force_bit(). So let's
dedicate the high bit as a flag for the low level timeout based fallback
and treat the rest of the bits as a ref count just as before.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457366220-29409-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: Jani Nikula <jani.nikula@intel.com>

Extend the protection of gmbus_mutex around the force_bit
RMW in intel_gmbus_force_bit(), in case someone gets the
idea of calling it from a separate thread while there's
other stuff happening on the same bus.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457366220-29409-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: Jani Nikula <jani.nikula@intel.com>

Since we only ever use the drm_i915_private from the stored
i915_mm_struct->dev, save some electrons by storing the right
backpointer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-3-git-send-email-chris@chris-wilson.co.uk

Holding a reference to the containing task_struct is not sufficient to
prevent the mm_struct from being reaped under memory pressure. If this
happens whilst we are calling get_user_pages(), explosions erupt -
sometimes an immediate GPF, sometimes page flag corruption. To prevent
the target mm from being reaped as we are reading from it, acquire a
reference before we begin.

Testcase: igt/gem_shrink/*userptr
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-2-git-send-email-chris@chris-wilson.co.uk

In order to ensure that all invalidations are completed before the
operation returns to userspace (i.e. before the munmap() syscall returns)
we need to wait upon the outstanding operations.

We are allowed to block inside the invalidate_range_start callback, and
as struct_mutex is the inner lock with mmap_sem we can wait upon the
struct_mutex without provoking lockdep into warning about a deadlock.
However, we don't actually want to wait upon outstanding rendering
whilst holding the struct_mutex if we can help it otherwise we also
block other processes from submitting work to the GPU. So first we do a
wait without the lock and then when we reacquire the lock, we double
check that everything is ready for removing the invalidated pages.

Finally to wait upon the outstanding unpinning tasks, we create a
private workqueue as a means to conveniently wait upon all at once. The
drawback is that this workqueue is per-mm, so any threads concurrently
invalidating objects will wait upon each other. The advantage of using
the workqueue is that we can wait in parallel for completion of
rendering and unpinning of several objects (of particular importance if
the process terminates with a whole mm full of objects).

v2: Apply a cup of tea to the changelog.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94699
Testcase: igt/gem_userptr_blits/sync-unmap-cycles
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-1-git-send-email-chris@chris-wilson.co.ukReviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Linux 4.6-rc3

Backmerge requested by Chris Wilson to make his patches apply cleanly.
Tiny conflict in vmalloc.c with the (properly acked and all) patch in
drm-intel-next:

commit 4da56b99
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Mon Apr 4 14:46:42 2016 +0100

    mm/vmap: Add a notifier for when we run out of vmap address space

and Linus' tree.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

If we want a contiguous mapping of a single page sized object, we can
forgo using vmap() and just use a regular kmap(). Note that this is only
suitable if the desired pgprot_t is compatible.

v2: Use is_vmalloc_addr()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-7-git-send-email-chris@chris-wilson.co.ukReviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>

I have instances where I want to use drm_malloc_ab() but with a custom
gfp mask. And with those, where I want a temporary allocation, I want to
try a high-order kmalloc() before using a vmalloc().

So refactor my usage into drm_malloc_gfp().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-6-git-send-email-chris@chris-wilson.co.uk

When called because we have run out of vmap address space, we only need
to recover objects that have vmappings and not all.

v2: Start using is_vmalloc_addr()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-5-git-send-email-chris@chris-wilson.co.ukReviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>

We now have two implementations for vmapping a whole object, one for
dma-buf and one for the ringbuffer. If we couple the mapping into the
obj->pages lifetime, then we can reuse an obj->mapping for both and at
the same time couple it into the shrinker. There is a third vmapping
routine in the cmdparser that maps only a range within the object, for
the time being that is left alone, but will eventually use these routines
in order to cache the mapping between invocations.

v2: Mark the failable kmalloc() as __GFP_NOWARN (vsyrjala)
v3: Call unpin_vmap from the right dmabuf unmapper

v4: Rename vmap to map as we don't wish to imply the type of mapping
involved, just that it contiguously maps the object into kernel space.
Add kerneldoc and lockdep annotations
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-4-git-send-email-chris@chris-wilson.co.ukReviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>

After we pin the ringbuffer into the GGTT, all error paths need to unpin
it again. Move this common step into one block, and make the unable to
iomap error code consistent (i.e. treat it as out of memory to avoid
confusing it with a invalid argument).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-3-git-send-email-chris@chris-wilson.co.uk

We only need the struct_mutex to manipulate the pages_pin_count on the
object, we do not need to hold our BKL when freeing the exported
scatterlist.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-2-git-send-email-chris@chris-wilson.co.uk

This is to fix a GPU hang seen with mid thread pre-emption
and pooled EUs.

v2. Use IS_BXT_REVID instead of IS_BROXTON and INTEL_REVID

v3. And use correct type for register addresses
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458571049-854-1-git-send-email-tim.gore@intel.com

For BXT, description of polarities of PORT_PLL_REF_SEL
has been reversed for newer Gen9LP steppings according to the
recent update in Bspec. This bit now should be set for
"Non-SSC" mode for all Gen9LP starting from B0 stepping.

v2: Only B0 and newer stepping should be affected by this
change.
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94866Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458176773-26925-1-git-send-email-dongwon.kim@intel.com

Check functions are used by atomic to see if the new state will
be allowed. There's also a hw state checker which checks afterwards
that the committed state is correct. Rename it to hw state verifier
to reduce some confusion.
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56FB8785.8020506@linux.intel.comReviewed-by: Matt Roper <matthew.d.roper@intel.com>

The modeset state verifier no longer has full access to the hardware,
instead it should only verify affected crtc's.

Looking for disabled stuff can be verified immediately after all crtc
disables have completed, while each enabled crtc can be verified right
after being enabled.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458741487-23801-3-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mlankhorst: check -> verify]

This will make it easier to keep the crtc checker when atomic
commit is reworked for asynchronous commits. This prevents checking
crtc's that were not part of the state. It's safe to verify disabled
encoders, connectors and dpll's that are not part of the state,
because during modeset connection_mutex is held.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458741487-23801-2-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mlankhorst: Extend commit message and rename check to verify.]

Pull ARM fixes from Russell King:
 "A couple of small fixes, and wiring up the new syscalls which appeared
  during the merge window"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8550/1: protect idiv patching against undefined gcc behavior
  ARM: wire up preadv2 and pwritev2 syscalls
  ARM: SMP enable of cache maintanence broadcast

Pull MMC fixes from Ulf Hansson:
 "Here are a couple of mmc fixes intended for v4.6 rc3:

  MMC host:
   - sdhci: Fix regression setting power on Trats2 board
   - sdhci-pci: Add support and PCI IDs for more Broxton host controllers"

* tag 'mmc-v4.6-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: sdhci-pci: Add support and PCI IDs for more Broxton host controllers
  mmc: sdhci: Fix regression setting power on Trats2 board

Pull i2c fixes from Wolfram Sang:
 "Some bugfixes from I2C:

   - fix a uevent triggered boot problem by removing a useless debug
     print

   - fix sysfs-attributes of the new i2c-demux-pinctrl driver to follow
     standard kernel behaviour

   - fix a potential division-by-zero error (needed two takes)"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: jz4780: really prevent potential division by zero
  Revert "i2c: jz4780: prevent potential division by zero"
  i2c: jz4780: prevent potential division by zero
  i2c: mux: demux-pinctrl: Update docs to new sysfs-attributes
  i2c: mux: demux-pinctrl: Clean up sysfs attributes
  i2c: prevent endless uevent loop with CONFIG_I2C_DEBUG_CORE

This reverts commit 1028b55b.

It's broken: it makes ext4 return an error at an invalid point, causing
the readdir wrappers to write the the position of the last successful
directory entry into the position field, which means that the next
readdir will now return that last successful entry _again_.

You can only return fatal errors (that terminate the readdir directory
walk) from within the filesystem readdir functions, the "normal" errors
(that happen when the readdir buffer fills up, for example) happen in
the iterorator where we know the position of the actual failing entry.

I do have a very different patch that does the "signal_pending()"
handling inside the iterator function where it is allowable, but while
that one passes all the sanity checks, I screwed up something like four
times while emailing it out, so I'm not going to commit it today.

So my track record is not good enough, and the stars will have to align
better before that one gets committed.  And it would be good to get some
review too, of course, since celestial alignments are always an iffy
debugging model.

IOW, let's just revert the commit that caused the problem for now.
Reported-by: Greg Thelen <gthelen@google.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull parisc fixes from Helge Deller:
 "Since commit 0de79858 ("parisc: Use generic extable search and
  sort routines") module loading is boken on parisc, because the parisc
  module loader wasn't prepared for the new R_PARISC_PCREL32 relocations.

  In addition, due to that breakage, Mikulas Patocka noticed that
  handling exceptions from modules probably never worked on parisc.  It
  was just masked by the fact that exceptions from modules don't happen
  during normal use.

  This patch series fixes those issues and survives the tests of the
  lib/test_user_copy kernel module test.  Some patches are tagged for
  stable"

* 'parisc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Update comment regarding relative extable support
  parisc: Unbreak handling exceptions from kernel modules
  parisc: Fix kernel crash with reversed copy_from_user()
  parisc: Avoid function pointers for kernel exception routines
  parisc: Handle R_PARISC_PCREL32 relocations in kernel modules

Pull libnvdimm fixes from Dan Williams:
 "Three fixes, the first two are tagged for -stable:

   - The ndctl utility/library gained expanded unit tests illuminating a
     long standing bug in the libnvdimm SMART data retrieval
     implementation.

     It has been broken since its initial implementation, now fixed.

   - Another one line fix for the detection of stale info blocks.

     Without this change userspace can get into a situation where it is
     unable to reconfigure a namespace.

   - Fix the badblock initialization path in the presence of the new (in
     v4.6-rc1) section alignment workarounds.

     Without this change badblocks will be reported at the wrong offset.

  These have received a build success report from the kbuild robot and
  have appeared in -next with no reported issues"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm, pfn: fix nvdimm_namespace_add_poison() vs section alignment
  libnvdimm, pfn: fix uuid validation
  libnvdimm: fix smart data retrieval

Pull GPIO fixes from Linus Walleij:
 "Here is a set of four GPIO fixes.  The two fixes to the core are
  serious as they are regressing minor architectures.

  Core fixes:

   - Defer GPIO device setup until after gpiolib is initialized.

     It turns out that a few very tightly integrated GPIO platform
     drivers initialize so early (befor core_initcall()) so that the
     gpiolib isn't even initialized itself.  That limits what the
     library can do, and we cannot reference uninitialized fields until
     later.

     Defer some of the initialization until right after the gpiolib is
     initialized in these (rare) cases.

   - As a consequence: do not use devm_* resources when allocating the
     states in the initial set-up of the gpiochip.

  Driver fixes:

   - In ACPI retrieveal: ignore GpioInt when looking for output GPIOs.

   - Fix legacy builds on the PXA without a backing pin controller.

   - Use correct datatype on pca953x register writes"

* tag 'gpio-v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: pca953x: Use correct u16 value for register word write
  gpiolib: Defer gpio device setup until after gpiolib initialization
  gpiolib: Do not use devm functions when registering gpio chip
  gpio: pxa: fix legacy non pinctrl aware builds
  gpio / ACPI: ignore GpioInt() GPIOs when requesting GPIO_OUT_*

Pull tty fixes from Greg KH:
 "Here are two tty fixes for issues found.

  One was due to a merge error in 4.6-rc1, and the other a regression
  fix for UML consoles that broke in 4.6-rc1.

  Both have been in linux-next for a while"

* tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix merge of "tty: Refactor tty_open()"
  tty: Fix UML console breakage

Pull USB fixes from Greg KH:
 "Here are some USB fixes and new device ids for 4.6-rc3.

  Nothing major, the normal USB gadget fixes and usb-serial driver ids,
  along with some other fixes mixed in.  All except the USB serial ids
  have been tested in linux-next, the id additions should be fine as
  they are 'trivial'"

* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  USB: option: add "D-Link DWM-221 B1" device id
  USB: serial: cp210x: Adding GE Healthcare Device ID
  USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
  usb: dwc3: keystone: drop dma_mask configuration
  usb: gadget: udc-core: remove manual dma configuration
  usb: dwc3: pci: add ID for one more Intel Broxton platform
  usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
  usb: dwc2: do not override forced dr_mode in gadget setup
  usb: gadget: f_midi: unlock on error
  USB: digi_acceleport: do sanity checking for the number of ports
  USB: cypress_m8: add endpoint sanity check
  USB: mct_u232: add sanity checking in probe
  usb: fix regression in SuperSpeed endpoint descriptor parsing
  USB: usbip: fix potential out-of-bounds write
  usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
  usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
  usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
  usb: phy: qcom-8x16: fix regulator API abuse
  usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
  usb: gadget: composite: Access SSP Dev Cap fields properly
  ...

Pull staging and IIO driver fixes from Greg KH:
 "Here are some IIO driver fixes, along with two staging driver fixes
  for 4.6-rc3.

  One staging driver patch reverts the deletion of a driver that
  happened in 4.6-rc1.  We thought that laptop.org was dead, but it's
  still alive and kicking, and has users that were mad we broke their
  hardware by deleting a driver for their machines.  So that driver is
  added back and everyone is happy again.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert "Staging: olpc_dcon: Remove obsolete driver"
  staging/rdma/hfi1: select CRC32
  iio: gyro: bmg160: fix buffer read values
  iio: gyro: bmg160: fix endianness when reading axes
  iio: accel: bmc150: fix endianness when reading axes
  iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
  iio: fix config watermark initial value
  iio: health: max30100: correct FIFO check condition
  iio: imu: Fix inv_mpu6050 dependencies
  iio: adc: Fix build error of missing devm_ioremap_resource on UM
  iio: light: apds9960: correct FIFO check condition
  iio: adc: max1363: correct reference voltage
  iio: adc: max1363: add missing adc to max1363_id

Pull SCSI fixes from James Bottomley:
 "This is a set of eight fixes.

  Two are trivial gcc-6 updates (brace additions and unused variable
  removal).  There's a couple of cxlflash regressions, a correction for
  sd being overly chatty on revalidation (causing excess log increases).
  A VPD issue which could crash USB devices because they seem very
  intolerant to VPD inquiries, an ALUA deadlock fix and a mpt3sas buffer
  overrun fix"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: Do not attach VPD to devices that don't support it
  sd: Fix excessive capacity printing on devices with blocks bigger than 512 bytes
  scsi_dh_alua: Fix a recently introduced deadlock
  scsi: Declare local symbols static
  cxlflash: Move to exponential back-off when cmd_room is not available
  cxlflash: Fix regression issue with re-ordering patch
  mpt3sas: Don't overreach ioc->reply_post[] during initialization
  aacraid: add missing curly braces

Pull MD fixes from Shaohua Li:
 "This update mainly fixes bugs:

   - fix error handling (Guoqing)
   - fix a crash when a disk is hotremoved (me)
   - fix a dead loop (Wei Fang)"

* tag 'md/4.6-rc2-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/bitmap: clear bitmap if bitmap_create failed
  MD: add rdev reference for super write
  md: fix a trivial typo in comments
  md:raid1: fix a dead loop when read from a WriteMostly disk

Pull power management and ACPI fixes from Rafael Wysocki:
 "Fixes for some issues discovered after recent changes and for some
  that have just been found lately regardless of those changes
  (intel_pstate, intel_idle, PM core, mailbox/pcc, turbostat) plus
  support for some new CPU models (intel_idle, Intel RAPL driver,
  turbostat) and documentation updates (intel_pstate, PM core).

  Specifics:

   - intel_pstate fixes for two issues exposed by the recent switch over
     from using timers and for one issue introduced during the 4.4 cycle
     plus new comments describing data structures used by the driver
     (Rafael Wysocki, Srinivas Pandruvada).

   - intel_idle fixes related to CPU offline/online (Richard Cochran).

   - intel_idle support (new CPU IDs and state definitions mostly) for
     Skylake-X and Kabylake processors (Len Brown).

   - PCC mailbox driver fix for an out-of-bounds memory access that may
     cause the kernel to panic() (Shanker Donthineni).

   - New (missing) CPU ID for one apparently overlooked Haswell model in
     the Intel RAPL power capping driver (Srinivas Pandruvada).

   - Fix for the PM core's wakeup IRQs framework to make it work after
     wakeup settings reconfiguration from sysfs (Grygorii Strashko).

   - Runtime PM documentation update to make it describe what needs to
     be done during device removal more precisely (Krzysztof Kozlowski).

   - Stale comment removal cleanup in the cpufreq-dt driver (Viresh
     Kumar).

   - turbostat utility fixes and support for Broxton, Skylake-X and
     Kabylake processors (Len Brown)"

* tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
  PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
  tools/power turbostat: work around RC6 counter wrap
  tools/power turbostat: initial KBL support
  tools/power turbostat: initial SKX support
  tools/power turbostat: decode BXT TSC frequency via CPUID
  tools/power turbostat: initial BXT support
  tools/power turbostat: print IRTL MSRs
  tools/power turbostat: SGX state should print only if --debug
  intel_idle: Add KBL support
  intel_idle: Add SKX support
  intel_idle: Clean up all registered devices on exit.
  intel_idle: Propagate hot plug errors.
  intel_idle: Don't overreact to a cpuidle registration failure.
  intel_idle: Setup the timer broadcast only on successful driver load.
  intel_idle: Avoid a double free of the per-CPU data.
  intel_idle: Fix dangling registration on error path.
  intel_idle: Fix deallocation order on the driver exit path.
  intel_idle: Remove redundant initialization calls.
  intel_idle: Fix a helper function's return value.
  intel_idle: remove useless return from void function.
  ...

Pull networking fixes from David Miller:

 1) Stale SKB data pointer access across pskb_may_pull() calls in L2TP,
    from Haishuang Yan.

 2) Fix multicast frame handling in mac80211 AP code, from Felix
    Fietkau.

 3) mac80211 station hashtable insert errors not handled properly, fix
    from Johannes Berg.

 4) Fix TX descriptor count limit handling in e1000, from Alexander
    Duyck.

 5) Revert a buggy netdev refcount fix in netpoll, from Bjorn Helgaas.

 6) Must assign rtnl_link_ops of the device before registering it, fix
    in ip6_tunnel from Thadeu Lima de Souza Cascardo.

 7) Memory leak fix in tc action net exit, from WANG Cong.

 8) Add missing AF_KCM entries to name tables, from Dexuan Cui.

 9) Fix regression in GRE handling of csums wrt.  FOU, from Alexander
    Duyck.

10) Fix memory allocation alignment and congestion map corruption in
    RDS, from Shamir Rabinovitch.

11) Fix default qdisc regression in tuntap driver, from Jason Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  bridge, netem: mark mailing lists as moderated
  tuntap: restore default qdisc
  mpls: find_outdev: check for err ptr in addition to NULL check
  ipv6: Count in extension headers in skb->network_header
  RDS: fix congestion map corruption for PAGE_SIZE > 4k
  RDS: memory allocated must be align to 8
  GRE: Disable segmentation offloads w/ CSUM and we are encapsulated via FOU
  net: add the AF_KCM entries to family name tables
  MAINTAINERS: intel-wired-lan list is moderated
  lib/test_bpf: Add additional BPF_ADD tests
  lib/test_bpf: Add test to check for result of 32-bit add that overflows
  lib/test_bpf: Add tests for unsigned BPF_JGT
  lib/test_bpf: Fix JMP_JSET tests
  VSOCK: Detach QP check should filter out non matching QPs.
  stmmac: fix adjust link call in case of a switch is attached
  af_packet: tone down the Tx-ring unsupported spew.
  net_sched: fix a memory leak in tc action
  samples/bpf: Enable powerpc support
  samples/bpf: Use llc in PATH, rather than a hardcoded value
  samples/bpf: Fix build breakage with map_perf_test_user.c
  ...

Pull btrfs fixes from Chris Mason:
 "These are bug fixes, including a really old fsync bug, and a few trace
  points to help us track down problems in the quota code"

* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix file/data loss caused by fsync after rename and new inode
  btrfs: Reset IO error counters before start of device replacing
  btrfs: Add qgroup tracing
  Btrfs: don't use src fd for printk
  btrfs: fallback to vmalloc in btrfs_compare_tree
  btrfs: handle non-fatal errors in btrfs_qgroup_inherit()
  btrfs: Output more info for enospc_debug mount option
  Btrfs: fix invalid reference in replace_path
  Btrfs: Improve FL_KEEP_SIZE handling in fallocate

Pull orangefs fixes from Mike Marshall:
 "Orangefs cleanups and a strncpy vulnerability fix.

  Cleanups:
   - remove an unused variable from orangefs_readdir.
   - clean up printk wrapper used for ofs "gossip" debugging.
   - clean up truncate ctime and mtime setting in inode.c
   - remove a useless null check found by coccinelle.
   - optimize some memcpy/memset boilerplate code.
   - remove some useless sanity checks from xattr.c

  Fix:
   - fix a potential strncpy vulnerability"

* tag 'for-linus-4.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
  orangefs: remove unused variable
  orangefs: Add KERN_<LEVEL> to gossip_<level> macros
  orangefs: strncpy -> strscpy
  orangefs: clean up truncate ctime and mtime setting
  Orangefs: fix ifnullfree.cocci warnings
  Orangefs: optimize boilerplate code.
  Orangefs: xattr.c cleanup

Pull IOMMU fixes from Joerg Roedel:

 - compile-time fixes (warnings and failures)

 - a bug in iommu core code which could cause the group->domain pointer
   to be falsly cleared

 - fix in scatterlist handling of the ARM common DMA-API code

 - stall detection fix for the Rockchip IOMMU driver

* tag 'iommu-fixes-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/vt-d: Silence an uninitialized variable warning
  iommu/rockchip: Fix "is stall active" check
  iommu: Don't overwrite domain pointer when there is no default_domain
  iommu/dma: Restore scatterlist offsets correctly
  iommu: provide of_xlate pointer unconditionally

When reading from the HWS page, we use barrier() to prevent the compiler
optimising away the read from the volatile (may be updated by the GPU)
memory address. This is more suited to READ_ONCE(); make it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-5-git-send-email-chris@chris-wilson.co.uk

Rather than call a function to compute the matching cachelines and
clflush them, just call the clflush *instruction* directly. We also know
that we can use the unpatched plain clflush rather than the clflushopt
alternative.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-4-git-send-email-chris@chris-wilson.co.uk

Only declare a missed interrupt if we find that the GPU is idle with
waiters and a hangcheck interval has passed in which no new user
interrupts have been raised.

v2: Clear the stuck interrupt marker between successful batches
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-3-git-send-email-chris@chris-wilson.co.uk

In order to simplify future patches, extract the
lazy_coherency optimisation our of the engine->get_seqno() vfunc into
its own callback.

v2: Rename the barrier to engine->irq_seqno_barrier to try and better
reflect that the barrier is only required after the user interrupt before
reading the seqno (to ensure that the seqno update lands in time as we
do not have strict seqno-irq ordering on all platforms).

Reviewed-by: Dave Gordon <david.s.gordon@intel.com> [#v2]

v3: Comments for hangcheck paranoia. Mika wanted to keep the extra
barrier inside the hangcheck, just in case. I can argue that it doesn't
provide a barrier against anything, but the side-effects of applying the
barrier may prevent a false declaration of a hung GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-2-git-send-email-chris@chris-wilson.co.uk