The number of spare Tx blocks must be changed when the GEM cipher is
engaged. Track set_key() operations to see if this is the case and
change the Tx HW spare block count accordingly. Set the number of spare
blocks for each operating mode from the low level driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Each chip family can have a different amount of Tx descriptors. These
are set on init.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

This storage is allocated in wlcore_alloc_hw and freed in free_hw. The
size of the storage is determined by the low-level driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

ELP is a very complicated process in the firmware.  Due to its
complexity, in some early firmware revisions, the ELP feature is
disabled.  To support this cases, this patch adds a quirk that
disables ELP mode.

When ELP is not supported, do not attempt to enter ELP when requested by
the driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

We were reading the even mailbox address three times, which was
completely unnecessary and complicated things regarding partition
selection.  Remove the unnecessry reads and set the address for
mailbox 1 and 2 after the first read.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Instead of checking the chip ID directly in the wlcore code to decide
whether to use the new or the old NVS format, we now use a quirk that
should be set by the low level driver to say that it needs to use the
old format.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Different chips may use different bits in the interrupt trigger
register.  Add operations to handle these differences.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Different chip families have the factory MAC address written in
different places.  Add a new hardware operation to read the MAC
address, if available.
Signed-off-by: Luciano Coelho <coelho@ti.com>

The top registers initialization is very specific to the actual
hardware used, even the way in which we read from and write to the top
registers varies from chip to chip.  This patch moves all top
registers initialization to wl12xx.  Also add a boot op for the wlcore
module to call at the right time and a few callbacks with the common
called to be called from the lower drivers boot operations.
Signed-off-by: Luciano Coelho <coelho@ti.com>

The PG version depends on the actual hardware.  This commit moves the
code used to read the PG version to the lower driver, by adding the
get_pg_ver hardware operation.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Move the code that identifies the chip ID and selects the appropriate
firmware to an operation implemented by the lower driver.  Also move
the quirks definitions into wlcore.h and rename to WLCORE_QUIRK_*.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Add register tables support in wlcore, add some new IO functions to
read and write to chip-specific register and data addresses.  Move
some common register values from wl12xx to wlcore and add the
registers table to wl12xx.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Add partition tables to wlcore, move and reorganize partition setting
functions.  Move wl12xx partition table to use the wlcore partition
table instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>

In order to add chip-specific operations and prepare for future
elements that need to be set by the lower driver, move the wl1271
structure to the wlcore.h file and add an empty placeholder for the
operations structure.
Signed-off-by: Luciano Coelho <coelho@ti.com>

We need to set some parameters (eg. partition and register tables)
during probe of the lower driver, so split the probe function, leaving
most of it in wlcore, but moving the hw struct allocation to the lower
driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Create a new small wl12xx module that only contains the probe
functions and depends entirely on wlcore otherwise.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Rename the wl12xx driver directory to wlcore as an initial step
towards the split of the driver into wlcore and wl12xx.  We just
rename the directory first to keep git blame happy.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Move wl12xx and wl1251 modules into a new drivers/net/wireless/ti
directory.  Add a TI WLAN Kconfig option and Makefile to support this
change.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Cc: John W. Linville <linville@tuxdriver.com>

In certain scenarios involving sched scan + normal scan + COEX
scan could take longer than 10s and this triggers a recovery
where it shouldn't. Increase the timeout to avoid that.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Set the dwell times for sched scan according to the number
of probe requests which are going to be transmitted.
This should fix the too short dwell time problem which
prevented some of the probe requests from being transmitted
in cases of high number of SSIDs (10+) to be actively sched scanned.
However, in the common case of having up to 1-2 SSIDs that
require active scan, the dwell time would be kept to a minimum
which should conserve power. This is important as sched scan
also runs periodically while the host is suspended and there's
great importance to keep power consumption as low as possible.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
[fixed a couple of new strict checkpatch warnings]
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlvif->probereq is zeroed when adding an interface but
the skb pointed to isn't freed when the interface is removed.
This would lead to a mem leak on every recovery.
Fix it by freeing the skb when removing the interface.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

The ap keys should be freed only when removing
ap role (otherwise, some arbitrary data might
get freed).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

On the PandaBoard (omap_hsmmc + wl12xx_sdio) with DMA_API_DEBUG:

 WARNING: at lib/dma-debug.c:930 check_for_stack.part.8+0x7c/0xe0()
 omap_hsmmc omap_hsmmc.4: DMA-API: device driver maps memory fromstack
Signed-off-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

The iteration on the wlvif list in wl1271_op_resume/suspend was
perfomed before locking wl->mutex which would lead to a kernel
panic in case a recovery was queued at the same time
and would delete the wlvifs from the list.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Channel switch complete event wasn't handled
properly in station mode, as we checked wrong
CS flag.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx sets the do_join flag (which later starts the
sta role) when the bssid was changed and the sta is
associated. However, this no longer happens after
the "mac80211: remove spurious BSSID change flag"
patch.

Fix it by setting the do_join flag on BSS_CHANGED_ASSOC
(for IBSS, do_join is already set on BSS_CHANGED_IBSS)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Move the POWER_PMI to the op_mode where it is changed.  The trans needs
to check it frequently, so shadow the status in the trans and update it
in trans when it infrequently changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The op_mode should check for FW_ERROR before calling send_cmd.  This
removes the need to test for FW_ERROR in the trans layer.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With error logging now completely handled in
the op_mode, the transport layer does not
need to know information about the loaded
firmware.

Remove this state information from the
iwl_shared data structure.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl_get_single_channel_number is used only in
iwl-scan.c, move it there and mark it static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl_full_rxon_required is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl_check_rxon_cmd is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl_set_rxon_hwcrypto is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl_send_rxon_timing is used only in
iwl-agn-rxon.c, move it there and mark it
static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is used only in one file, move it there
and make it static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This variable holds the ucode currently
running on the device; which is determined by
op_mode, so move this parameter there.

Also, the name of the variable is a bit
misleading, so rename it to cur_ucode.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Error log reporting does not belong to the
transport layer, but to the op_mode loading
the ucode, as it is the entity which knows
about the ucode loaded, and what the error
information means.

Move device logging pointers from the
transport layer to op_mode.

With this change, transport layer only
reports an error to the op_mode, which will
figure out what to do with the error. This
causes the driver to now dump out error logs
when the command queue is stuck as well.

Also, move the debugfs entry for event logs
out of the transport layer and into op_mode.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl_nic_error is used in iwl-agn.c only, move
it there and make it static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the process, make iwlagn_fw_error
a non-static function, as it is used
by more than one file.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No other component is accessing it any more,
so it can move to the correct place in priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>