- 13 Mar, 2019 40 commits
-
-
Martin Blumenstingl authored
[ Upstream commit 8615f559 ] After commit 89a5e15b ("gpio/mmc/of: Respect polarity in the device tree") SD cards are not detected anymore. The CD GPIO is "active low" on the MXIII-Plus. The MMC dt-bindings specify: "[...] using the "cd-inverted" property means, that the CD line is active high, i.e. it is high, when a card is inserted". Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and drop the "cd-inverted" property. This makes the definition consistent with the existing dt-bindings and fixes the check whether an SD card is inserted. Fixes: 35ee52be ("ARM: dts: meson8m2: add support for the Tronsmart MXIII Plus") Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Martin Blumenstingl authored
[ Upstream commit 3fb348e0 ] After commit 89a5e15b ("gpio/mmc/of: Respect polarity in the device tree") SD cards are not detected anymore. The CD GPIO is "active low" on Odroid-C1. The MMC dt-bindings specify: "[...] using the "cd-inverted" property means, that the CD line is active high, i.e. it is high, when a card is inserted". Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and drop the "cd-inverted" property. This makes the definition consistent with the existing dt-bindings and fixes the check whether an SD card is inserted. Fixes: e03efbce ("ARM: dts: meson8b-odroidc1: add microSD support") Signed-off-by:
Anand Moon <linux.amoon@gmail.com> Signed-off-by:
-
Carlo Caione authored
[ Upstream commit e35e26b2 ] A long running stress test on a custom board shipping an AXG SoCs and a Realtek RTL8211F PHY revealed that after a few hours the connection speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time the 'macirq' (eth0) IRQ would stop being triggered at all and as consequence the GMAC IRQs never ACKed. After a painful investigation the problem seemed to be due to a wrong defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of EDGE_RISING. The change in the macirq IRQ type also solved another long standing issue affecting this SoC/PHY where EEE was causing the network connection to die after stressing it with iperf3 (even though much sooner). It's now possible to remove the 'eee-broken-1000t' quirk as well. Fixes: 9c15795a ("ARM: dts: meson8b-odroidc1: ethernet support") Signed-off-by:
Carlo Caione <ccaione@baylibre.com> Reviewed-by:
-
Jernej Skrabec authored
[ Upstream commit cc4bddad ] Because "ethernet0" alias is missing, U-Boot doesn't generate board specific MAC address. Effect of this is random MAC address every boot and thus new IP address is assigned to the board. Fix this by adding alias. Fixes: 7389172f ("ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2") Signed-off-by:
Jernej Skrabec <jernej.skrabec@siol.net> [Maxime: Removed unneeded comment] Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit ef4a55b9 ] We're now getting the following error: genirq: Setting trigger mode 1 for irq 230 failed (regmap_irq_set_type+0x0/0x15c) cpcap-usb-phy cpcap-usb-phy.0: could not get irq dp: -524 Cc: Sebastian Reichel <sre@kernel.org> Reported-by:
Pavel Machek <pavel@ucw.cz> Tested-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Aaro Koskinen authored
[ Upstream commit 8443e484 ] Commit a758f50f ("mtd: onenand: omap2: Configure driver from DT") started using DT specified timings for GPMC, and as a result the OneNAND stopped working on N950/N9 as we had wrong values in the DT. Fix by updating the values to bootloader timings that have been tested to be working on both Nokia N950 and N9. Fixes: a758f50f ("mtd: onenand: omap2: Configure driver from DT") Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
-
Michal Hocko authored
[ Upstream commit 891cb2a7 ] Rong Chen has reported the following boot crash: PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 1 PID: 239 Comm: udevd Not tainted 5.0.0-rc4-00149-gefad4e47 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014 RIP: 0010:page_mapping+0x12/0x80 Code: 5d c3 48 89 df e8 0e ad 02 00 85 c0 75 da 89 e8 5b 5d c3 0f 1f 44 00 00 53 48 89 fb 48 8b 43 08 48 8d 50 ff a8 01 48 0f 45 da <48> 8b 53 08 48 8d 42 ff 83 e2 01 48 0f 44 c3 48 83 38 ff 74 2f 48 RSP: 0018:ffff88801fa87cd8 EFLAGS: 00010202 RAX: ffffffffffffffff RBX: fffffffffffffffe RCX: 000000000000000a RDX: fffffffffffffffe RSI: ffffffff820b9a20 RDI: ffff88801e5c0000 RBP: 6db6db6db6db6db7 R08: ffff88801e8bb000 R09: 0000000001b64d13 R10: ffff88801fa87cf8 R11: 0000000000000001 R12: ffff88801e640000 R13: ffffffff820b9a20 R14: ffff88801f145258 R15: 0000000000000001 FS: 00007fb2079817c0(0000) GS:ffff88801dd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000006 CR3: 000000001fa82000 CR4: 00000000000006a0 Call Trace: __dump_page+0x14/0x2c0 is_mem_section_removable+0x24c/0x2c0 removable_show+0x87/0xa0 dev_attr_show+0x25/0x60 sysfs_kf_seq_show+0xba/0x110 seq_read+0x196/0x3f0 __vfs_read+0x34/0x180 vfs_read+0xa0/0x150 ksys_read+0x44/0xb0 do_syscall_64+0x5e/0x4a0 entry_SYSCALL_64_after_hwframe+0x49/0xbe and bisected it down to commit efad4e47 ("mm, memory_hotplug: is_mem_section_removable do not pass the end of a zone"). The reason for the crash is that the mapping is garbage for poisoned (uninitialized) page. This shouldn't happen as all pages in the zone's boundary should be initialized. Later debugging revealed that the actual problem is an off-by-one when evaluating the end_page. 'start_pfn + nr_pages' resp 'zone_end_pfn' refers to a pfn after the range and as such it might belong to a differen memory section. This along with CONFIG_SPARSEMEM then makes the loop condition completely bogus because a pointer arithmetic doesn't work for pages from two different sections in that memory model. Fix the issue by reworking is_pageblock_removable to be pfn based and only use struct page where necessary. This makes the code slightly easier to follow and we will remove the problematic pointer arithmetic completely. Link: http://lkml.kernel.org/r/20190218181544.14616-1-mhocko@kernel.org Fixes: efad4e47 ("mm, memory_hotplug: is_mem_section_removable do not pass the end of a zone") Signed-off-by:
Michal Hocko <mhocko@suse.com> Reported-by: <rong.a.chen@intel.com> Tested-by: <rong.a.chen@intel.com> Acked-by:
Mike Rapoport <rppt@linux.ibm.com> Reviewed-by:
Oscar Salvador <osalvador@suse.de> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Ian Kent authored
[ Upstream commit f585b283 ] In autofs_fill_super() on error of get inode/make root dentry the return should be ENOMEM as this is the only failure case of the called functions. Link: http://lkml.kernel.org/r/154725123240.11260.796773942606871359.stgit@pluto-themaw-netSigned-off-by:
Ian Kent <raven@themaw.net> Signed-off-by:
-
Pan Bian authored
[ Upstream commit 63ce5f55 ] autofs_expire_run() calls dput(dentry) to drop the reference count of dentry. However, dentry is read via autofs_dentry_ino(dentry) after that. This may result in a use-free-bug. The patch drops the reference count of dentry only when it is never used. Link: http://lkml.kernel.org/r/154725122396.11260.16053424107144453867.stgit@pluto-themaw-netSigned-off-by:
Pan Bian <bianpan2016@163.com> Signed-off-by:
-
Jan Kara authored
[ Upstream commit c27d82f5 ] When superblock has lots of inodes without any pagecache (like is the case for /proc), drop_pagecache_sb() will iterate through all of them without dropping sb->s_inode_list_lock which can lead to softlockups (one of our customers hit this). Fix the problem by going to the slow path and doing cond_resched() in case the process needs rescheduling. Link: http://lkml.kernel.org/r/20190114085343.15011-1-jack@suse.czSigned-off-by:
Jan Kara <jack@suse.cz> Acked-by:
-
Dan Carpenter authored
[ Upstream commit db7ddeab ] There is a copy and paste bug so we set "config->test_driver" to NULL twice instead of setting "config->test_fs". Smatch complains that it leads to a double free: lib/test_kmod.c:840 __kmod_config_init() warn: 'config->test_fs' double freed Link: http://lkml.kernel.org/r/20190121140011.GA14283@kadam Fixes: d9c6a72d ("kmod: add test driver to stress test the module loader") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
-
Mikhail Zaslonko authored
[ Upstream commit 24feb47c ] If memory end is not aligned with the sparse memory section boundary, the mapping of such a section is only partly initialized. This may lead to VM_BUG_ON due to uninitialized struct pages access from test_pages_in_a_zone() function triggered by memory_hotplug sysfs handlers. Here are the the panic examples: CONFIG_DEBUG_VM_PGFLAGS=y kernel parameter mem=2050M -------------------------- page:000003d082008000 is uninitialized and poisoned page dumped because: VM_BUG_ON_PAGE(PagePoisoned(p)) Call Trace: test_pages_in_a_zone+0xde/0x160 show_valid_zones+0x5c/0x190 dev_attr_show+0x34/0x70 sysfs_kf_seq_show+0xc8/0x148 seq_read+0x204/0x480 __vfs_read+0x32/0x178 vfs_read+0x82/0x138 ksys_read+0x5a/0xb0 system_call+0xdc/0x2d8 Last Breaking-Event-Address: test_pages_in_a_zone+0xde/0x160 Kernel panic - not syncing: Fatal exception: panic_on_oops Fix this by checking whether the pfn to check is within the zone. [mhocko@suse.com: separated this change from http://lkml.kernel.org/r/20181105150401.97287-2-zaslonko@linux.ibm.com] Link: http://lkml.kernel.org/r/20190128144506.15603-3-mhocko@kernel.org [mhocko@suse.com: separated this change from http://lkml.kernel.org/r/20181105150401.97287-2-zaslonko@linux.ibm.com] Signed-off-by:
Mikhail Zaslonko <zaslonko@linux.ibm.com> Tested-by:
Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com> Reviewed-by:
Gerald Schaefer <gerald.schaefer@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Signed-off-by:
-
Michal Hocko authored
[ Upstream commit efad4e47 ] Patch series "mm, memory_hotplug: fix uninitialized pages fallouts", v2. Mikhail Zaslonko has posted fixes for the two bugs quite some time ago [1]. I have pushed back on those fixes because I believed that it is much better to plug the problem at the initialization time rather than play whack-a-mole all over the hotplug code and find all the places which expect the full memory section to be initialized. We have ended up with commit 2830bf6f ("mm, memory_hotplug: initialize struct pages for the full memory section") merged and cause a regression [2][3]. The reason is that there might be memory layouts when two NUMA nodes share the same memory section so the merged fix is simply incorrect. In order to plug this hole we really have to be zone range aware in those handlers. I have split up the original patch into two. One is unchanged (patch 2) and I took a different approach for `removable' crash. [1] http://lkml.kernel.org/r/20181105150401.97287-2-zaslonko@linux.ibm.com [2] https://bugzilla.redhat.com/show_bug.cgi?id=1666948 [3] http://lkml.kernel.org/r/20190125163938.GA20411@dhcp22.suse.cz This patch (of 2): Mikhail has reported the following VM_BUG_ON triggered when reading sysfs removable state of a memory block: page:000003d08300c000 is uninitialized and poisoned page dumped because: VM_BUG_ON_PAGE(PagePoisoned(p)) Call Trace: is_mem_section_removable+0xb4/0x190 show_mem_removable+0x9a/0xd8 dev_attr_show+0x34/0x70 sysfs_kf_seq_show+0xc8/0x148 seq_read+0x204/0x480 __vfs_read+0x32/0x178 vfs_read+0x82/0x138 ksys_read+0x5a/0xb0 system_call+0xdc/0x2d8 Last Breaking-Event-Address: is_mem_section_removable+0xb4/0x190 Kernel panic - not syncing: Fatal exception: panic_on_oops The reason is that the memory block spans the zone boundary and we are stumbling over an unitialized struct page. Fix this by enforcing zone range in is_mem_section_removable so that we never run away from a zone. Link: http://lkml.kernel.org/r/20190128144506.15603-2-mhocko@kernel.orgSigned-off-by:
-
Qian Cai authored
[ Upstream commit a8e911d1 ] If the kernel is configured with KASAN_EXTRA, the stack size is increasted significantly because this option sets "-fstack-reuse" to "none" in GCC [1]. As a result, it triggers stack overrun quite often with 32k stack size compiled using GCC 8. For example, this reproducer https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/syscalls/madvise/madvise06.c triggers a "corrupted stack end detected inside scheduler" very reliably with CONFIG_SCHED_STACK_END_CHECK enabled. There are just too many functions that could have a large stack with KASAN_EXTRA due to large local variables that have been called over and over again without being able to reuse the stacks. Some noticiable ones are size 7648 shrink_page_list 3584 xfs_rmap_convert 3312 migrate_page_move_mapping 3312 dev_ethtool 3200 migrate_misplaced_transhuge_page 3168 copy_process There are other 49 functions are over 2k in size while compiling kernel with "-Wframe-larger-than=" even with a related minimal config on this machine. Hence, it is too much work to change Makefiles for each object to compile without "-fsanitize-address-use-after-scope" individually. [1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715#c23 Although there is a patch in GCC 9 to help the situation, GCC 9 probably won't be released in a few months and then it probably take another 6-month to 1-year for all major distros to include it as a default. Hence, the stack usage with KASAN_EXTRA can be revisited again in 2020 when GCC 9 is everywhere. Until then, this patch will help users avoid stack overrun. This has already been fixed for arm64 for the same reason via 6e883067 ("arm64: kasan: Increase stack size for KASAN_EXTRA"). Link: http://lkml.kernel.org/r/20190109215209.2903-1-cai@lca.pwSigned-off-by:
Qian Cai <cai@lca.pw> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Alexey Dobriyan authored
[ Upstream commit 1fde6f21 ] /proc entries under /proc/net/* can't be cached into dcache because setns(2) can change current net namespace. [akpm@linux-foundation.org: coding-style fixes] [akpm@linux-foundation.org: avoid vim miscolorization] [adobriyan@gmail.com: write test, add dummy ->d_revalidate hook: necessary if /proc/net/* is pinned at setns time] Link: http://lkml.kernel.org/r/20190108192350.GA12034@avx2 Link: http://lkml.kernel.org/r/20190107162336.GA9239@avx2 Fixes: 1da4d377 ("proc: revalidate misc dentries") Signed-off-by:
Alexey Dobriyan <adobriyan@gmail.com> Reported-by:
Mateusz Stępień <mateusz.stepien@netrounds.com> Reported-by:
Ahmad Fatoum <a.fatoum@pengutronix.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Kairui Song authored
[ Upstream commit 2aa958c9 ] Kexec-ing a kernel with "efi=noruntime" on the first kernel's command line causes the following null pointer dereference: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] Call Trace: efi_runtime_map_copy+0x28/0x30 bzImage64_load+0x688/0x872 arch_kexec_kernel_image_load+0x6d/0x70 kimage_file_alloc_init+0x13e/0x220 __x64_sys_kexec_file_load+0x144/0x290 do_syscall_64+0x55/0x1a0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Just skip the EFI info setup if EFI runtime services are not enabled. [ bp: Massage commit message. ] Suggested-by:
Dave Young <dyoung@redhat.com> Signed-off-by:
Kairui Song <kasong@redhat.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Acked-by:
-
John Johansen authored
[ Upstream commit d6d478ae ] aa_label_merge() can return NULL for memory allocations failures make sure to handle and set the correct error in this case. Reported-by:
Peng Hao <peng.hao2@zte.com.cn> Signed-off-by:
John Johansen <john.johansen@canonical.com> Signed-off-by:
-
James Morse authored
[ Upstream commit f2b3d856 ] On systems with VHE the kernel and KVM's world-switch code run at the same exception level. Code that is only used on a VHE system does not need to be annotated as __hyp_text as it can reside anywhere in the kernel text. __hyp_text was also used to prevent kprobes from patching breakpoint instructions into this region, as this code runs at a different exception level. While this is no longer true with VHE, KVM still switches VBAR_EL1, meaning a kprobe's breakpoint executed in the world-switch code will cause a hyp-panic. Move the __hyp_text check in the kprobes blacklist so it applies on VHE systems too, to cover the common code and guest enter/exit assembly. Fixes: 888b3c87 ("arm64: Treat all entry code as non-kprobe-able") Reviewed-by:
Christoffer Dall <christoffer.dall@arm.com> Signed-off-by:
James Morse <james.morse@arm.com> Acked-by:
Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Thomas Lendacky authored
[ Upstream commit 912139cf ] The load_microcode_amd() function searches for microcode patches and attempts to apply a microcode patch if it is of different level than the currently installed level. While the processor won't actually load a level that is less than what is already installed, the logic wrongly returns UCODE_NEW thus signaling to its caller reload_store() that a late loading should be attempted. If the file-system contains an older microcode revision than what is currently running, such a late microcode reload can result in these misleading messages: x86/CPU: CPU features have changed after loading microcode, but might not take effect. x86/CPU: Please consider either early loading through initrd/built-in or a potential BIOS update. These messages were issued on a system where SME/SEV are not enabled by the BIOS (MSR C001_0010[23] = 0b) because during boot, early_detect_mem_encrypt() is called and cleared the SME and SEV features in this case. However, after the wrong late load attempt, get_cpu_cap() is called and reloads the SME and SEV feature bits, resulting in the messages. Update the microcode level check to not attempt microcode loading if the current level is greater than(!) and not only equal to the current patch level. [ bp: massage commit message. ] Fixes: 2613f36e ("x86/microcode: Attempt late loading only when new microcode is present") Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
-
Ronnie Sahlberg authored
[ Upstream commit 58d15ed1 ] The size of the fixed part of the create response is 88 bytes not 56. Signed-off-by:
Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Reviewed-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
-
Wei Huang authored
[ Upstream commit b677dfae ] In some old AMD KVM implementation, guest's EFER.LME bit is cleared by KVM when the hypervsior detects that the guest sets CR0.PG to 0. This causes the guest OS to reboot when it tries to return from 32-bit trampoline code because the CPU is in incorrect state: CR4.PAE=1, CR0.PG=1, CS.L=1, but EFER.LME=0. As a precaution, set EFER.LME=1 as part of long mode activation procedure. This extra step won't cause any harm when Linux is booted on a bare-metal machine. Signed-off-by:
Wei Huang <wei@redhat.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: bp@alien8.de Cc: hpa@zytor.com Link: https://lkml.kernel.org/r/20190104054411.12489-1-wei@redhat.comSigned-off-by:
-
Harini Katakam authored
[ Upstream commit e501070e ] The interrupt handler contains a workaround for RX hang applicable to Zynq and AT91RM9200 only. Subsequent versions do not need this workaround. This workaround unnecessarily resets RX whenever RX used bit read is observed, which can be often under heavy traffic. There is no other action performed on RX UBR interrupt. Hence introduce a CAPS mask; enable this interrupt and workaround only on affected versions. Signed-off-by:
Harini Katakam <harini.katakam@xilinx.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Sinan Kaya authored
[ Upstream commit 0ee4b5f8 ] Add BACKLIGHT_LCD_SUPPORT for SAMSUNG_Q10 to fix the warning: unmet direct dependencies detected for BACKLIGHT_CLASS_DEVICE. SAMSUNG_Q10 selects BACKLIGHT_CLASS_DEVICE but BACKLIGHT_CLASS_DEVICE depends on BACKLIGHT_LCD_SUPPORT. Copy BACKLIGHT_LCD_SUPPORT dependency into SAMSUNG_Q10 to fix: WARNING: unmet direct dependencies detected for BACKLIGHT_CLASS_DEVICE Depends on [n]: HAS_IOMEM [=y] && BACKLIGHT_LCD_SUPPORT [=n] Selected by [y]: - SAMSUNG_Q10 [=y] && X86 [=y] && X86_PLATFORM_DEVICES [=y] && ACPI [=y] Signed-off-by:
Sinan Kaya <okaya@kernel.org> Acked-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Sinan Kaya authored
[ Upstream commit d58bf90a ] Add BACKLIGHT_LCD_SUPPORT for ACPI_CMPC to fix the warning: unmet direct dependencies detected for BACKLIGHT_CLASS_DEVICE. ACPI_CMPC selects BACKLIGHT_CLASS_DEVICE but BACKLIGHT_CLASS_DEVICE depends on BACKLIGHT_LCD_SUPPORT. Copy BACKLIGHT_LCD_SUPPORT dependency into ACPI_CMPC to fix WARNING: unmet direct dependencies detected for BACKLIGHT_CLASS_DEVICE Depends on [n]: HAS_IOMEM [=y] && BACKLIGHT_LCD_SUPPORT [=n] Selected by [y]: - ACPI_CMPC [=y] && X86 [=y] && X86_PLATFORM_DEVICES [=y] && ACPI [=y] && INPUT [=y] && (RFKILL [=n] || RFKILL [=n]=n) Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 8437fcf1 ] The "hostdata->dev" pointer is NULL here. We set "hostdata->dev = dev;" later in the function and we also use "hostdata->dev" when we call dma_free_attrs() in NCR_700_release(). This bug predates git version control. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit b2d3492f ] There are two issues here. First if cmgr->hba is not set early enough then it leads to a NULL dereference. Second if we don't completely initialize cmgr->io_bdt_pool[] then we end up dereferencing uninitialized pointers. Fixes: 853e2bd2 ("[SCSI] bnx2fc: Broadcom FCoE offload driver") Signed-off-by:
-
Douglas Gilbert authored
[ Upstream commit 40d07b52 ] The WRITE SAME(10) and (16) implementations didn't take account of the buffer wrap required when the virtual_gb parameter is greater than 0. Fix that and rename the fake_store() function to lba2fake_store() to lessen confusion with the global fake_storep pointer. Bump version date. Signed-off-by:
Douglas Gilbert <dgilbert@interlog.com> Reported-by:
Bart Van Assche <bvanassche@acm.org> Tested by: Bart Van Assche <bvanassche@acm.org> Signed-off-by:
-
Ming Lu authored
[ Upstream commit 5d8fc4a9 ] The issue to be fixed in this commit is when libfc found it received a invalid FLOGI response from FC switch, it would return without freeing the fc frame, which is just the skb data. This would cause memory leak if FC switch keeps sending invalid FLOGI responses. This fix is just to make it execute `fc_frame_free(fp)` before returning from function `fc_lport_flogi_resp`. Signed-off-by:
Ming Lu <ming.lu@citrix.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Manish Chopra authored
[ Upstream commit ffb057f9 ] KASAN reported following bug in qed_init_qm_get_idx_from_flags due to inappropriate casting of "pq_flags". Fix the type of "pq_flags". [ 196.624707] BUG: KASAN: stack-out-of-bounds in qed_init_qm_get_idx_from_flags+0x1a4/0x1b8 [qed] [ 196.624712] Read of size 8 at addr ffff809b00bc7360 by task kworker/0:9/1712 [ 196.624714] [ 196.624720] CPU: 0 PID: 1712 Comm: kworker/0:9 Not tainted 4.18.0-60.el8.aarch64+debug #1 [ 196.624723] Hardware name: To be filled by O.E.M. Saber/Saber, BIOS 0ACKL024 09/26/2018 [ 196.624733] Workqueue: events work_for_cpu_fn [ 196.624738] Call trace: [ 196.624742] dump_backtrace+0x0/0x2f8 [ 196.624745] show_stack+0x24/0x30 [ 196.624749] dump_stack+0xe0/0x11c [ 196.624755] print_address_description+0x68/0x260 [ 196.624759] kasan_report+0x178/0x340 [ 196.624762] __asan_report_load_n_noabort+0x38/0x48 [ 196.624786] qed_init_qm_get_idx_from_flags+0x1a4/0x1b8 [qed] [ 196.624808] qed_init_qm_info+0xec0/0x2200 [qed] [ 196.624830] qed_resc_alloc+0x284/0x7e8 [qed] [ 196.624853] qed_slowpath_start+0x6cc/0x1ae8 [qed] [ 196.624864] __qede_probe.isra.10+0x1cc/0x12c0 [qede] [ 196.624874] qede_probe+0x78/0xf0 [qede] [ 196.624879] local_pci_probe+0xc4/0x180 [ 196.624882] work_for_cpu_fn+0x54/0x98 [ 196.624885] process_one_work+0x758/0x1900 [ 196.624888] worker_thread+0x4e0/0xd18 [ 196.624892] kthread+0x2c8/0x350 [ 196.624897] ret_from_fork+0x10/0x18 [ 196.624899] [ 196.624902] Allocated by task 2: [ 196.624906] kasan_kmalloc.part.1+0x40/0x108 [ 196.624909] kasan_kmalloc+0xb4/0xc8 [ 196.624913] kasan_slab_alloc+0x14/0x20 [ 196.624916] kmem_cache_alloc_node+0x1dc/0x480 [ 196.624921] copy_process.isra.1.part.2+0x1d8/0x4a98 [ 196.624924] _do_fork+0x150/0xfa0 [ 196.624926] kernel_thread+0x48/0x58 [ 196.624930] kthreadd+0x3a4/0x5a0 [ 196.624932] ret_from_fork+0x10/0x18 [ 196.624934] [ 196.624937] Freed by task 0: [ 196.624938] (stack is not available) [ 196.624940] [ 196.624943] The buggy address belongs to the object at ffff809b00bc0000 [ 196.624943] which belongs to the cache thread_stack of size 32768 [ 196.624946] The buggy address is located 29536 bytes inside of [ 196.624946] 32768-byte region [ffff809b00bc0000, ffff809b00bc8000) [ 196.624948] The buggy address belongs to the page: [ 196.624952] page:ffff7fe026c02e00 count:1 mapcount:0 mapping:ffff809b4001c000 index:0x0 compound_mapcount: 0 [ 196.624960] flags: 0xfffff8000008100(slab|head) [ 196.624967] raw: 0fffff8000008100 dead000000000100 dead000000000200 ffff809b4001c000 [ 196.624970] raw: 0000000000000000 0000000000080008 00000001ffffffff 0000000000000000 [ 196.624973] page dumped because: kasan: bad access detected [ 196.624974] [ 196.624976] Memory state around the buggy address: [ 196.624980] ffff809b00bc7200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 196.624983] ffff809b00bc7280: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 196.624985] >ffff809b00bc7300: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 04 f2 f2 f2 [ 196.624988] ^ [ 196.624990] ffff809b00bc7380: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 196.624993] ffff809b00bc7400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 196.624995] ================================================================== Signed-off-by:
Manish Chopra <manishc@marvell.com> Signed-off-by:
Ariel Elior <aelior@marvell.com> Signed-off-by:
-
Manish Chopra authored
[ Upstream commit 7c81626a ] Cache number of fragments in the skb locally as in case of linear skb (with zero fragments), tx completion (or freeing of skb) may happen before driver tries to get number of frgaments from the skb which could lead to stale access to an already freed skb. Signed-off-by:
-
Manish Chopra authored
[ Upstream commit 327852ec ] VFs may hit VF-PF channel timeout while probing, as in some cases it was observed that VF FLR and VF "acquire" message transaction (i.e first message from VF to PF in VF's probe flow) could occur simultaneously which could lead VF to fail sending "acquire" message to PF as VF is marked disabled from HW perspective due to FLR, which will result into channel timeout and VF probe failure. In such cases, try retrying VF "acquire" message so that in later attempts it could be successful to pass message to PF after the VF FLR is completed and can be probed successfully. Signed-off-by:
-
Manish Chopra authored
[ Upstream commit ff929696 ] VF is always configured to drop control frames (with reserved mac addresses) but to work LACP on the VFs, it would require LACP control frames to be forwarded or transmitted successfully. This patch fixes this in such a way that trusted VFs (marked through ndo_set_vf_trust) would be allowed to pass the control frames such as LACP pdus. Signed-off-by:
-
Manish Chopra authored
[ Upstream commit 9e71a15d ] When running tx switched traffic between VNICs created via a bridge(to which VFs are added), adapter drops the unicast packets in tx flow due to VNIC's ucast mac being unknown to it. But VF interfaces being in promiscuous mode should have caused adapter to accept all the unknown ucast packets. Later, it was found that driver doesn't really configure tx promiscuous mode settings to accept all unknown unicast macs. This patch fixes tx promiscuous mode settings to accept all unknown/unmatched unicast macs and works out the scenario. Signed-off-by:
-
Yao Liu authored
[ Upstream commit 80ff0017 ] There is a NULL pointer dereference of dev_name in nfs_parse_devname() The oops looks something like: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 ... RIP: 0010:nfs_fs_mount+0x3b6/0xc20 [nfs] ... Call Trace: ? ida_alloc_range+0x34b/0x3d0 ? nfs_clone_super+0x80/0x80 [nfs] ? nfs_free_parsed_mount_data+0x60/0x60 [nfs] mount_fs+0x52/0x170 ? __init_waitqueue_head+0x3b/0x50 vfs_kern_mount+0x6b/0x170 do_mount+0x216/0xdc0 ksys_mount+0x83/0xd0 __x64_sys_mount+0x25/0x30 do_syscall_64+0x65/0x220 entry_SYSCALL_64_after_hwframe+0x49/0xbe Fix this by adding a NULL check on dev_name Signed-off-by:
Yao Liu <yotta.liu@ucloud.cn> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Fathi Boudra authored
[ Upstream commit 7d4e591b ] posix_timers fails to build due to undefined reference errors: aarch64-linaro-linux-gcc --sysroot=/build/tmp-rpb-glibc/sysroots/hikey -O2 -pipe -g -feliminate-unused-debug-types -O3 -Wl,-no-as-needed -Wall -DKTEST -Wl,-O1 -Wl,--hash-style=gnu -Wl,--as-needed -lrt -lpthread posix_timers.c -o /build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/timers/posix_timers /tmp/cc1FTZzT.o: In function `check_timer_create': /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/timers/posix_timers.c:157: undefined reference to `timer_create' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/timers/posix_timers.c:170: undefined reference to `timer_settime' collect2: error: ld returned 1 exit status It's GNU Make and linker specific. The default Makefile rule looks like: $(CC) $(CFLAGS) $(LDFLAGS) $@ $^ $(LDLIBS) When linking is done by gcc itself, no issue, but when it needs to be passed to proper ld, only LDLIBS follows and then ld cannot know what libs to link with. More detail: https://www.gnu.org/software/make/manual/html_node/Implicit-Variables.html LDFLAGS Extra flags to give to compilers when they are supposed to invoke the linker, ‘ld’, such as -L. Libraries (-lfoo) should be added to the LDLIBS variable instead. LDLIBS Library flags or names given to compilers when they are supposed to invoke the linker, ‘ld’. LOADLIBES is a deprecated (but still supported) alternative to LDLIBS. Non-library linker flags, such as -L, should go in the LDFLAGS variable. https://lkml.org/lkml/2010/2/10/362 tools/perf: libraries must come after objects Link order matters, use LDLIBS instead of LDFLAGS to properly link against libpthread. Signed-off-by:
Denys Dmytriyenko <denys@ti.com> Signed-off-by:
Fathi Boudra <fathi.boudra@linaro.org> Signed-off-by:
Shuah Khan <shuah@kernel.org> Signed-off-by:
-
Fathi Boudra authored
[ Upstream commit 870f193d ] reuseport_bpf_numa fails to build due to undefined reference errors: aarch64-linaro-linux-gcc --sysroot=/build/tmp-rpb-glibc/sysroots/hikey -Wall -Wl,--no-as-needed -O2 -g -I../../../../usr/include/ -Wl,-O1 -Wl,--hash-style=gnu -Wl,--as-needed -lnuma reuseport_bpf_numa.c -o /build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/net/reuseport_bpf_numa /tmp/ccfUuExT.o: In function `send_from_node': /build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/net/reuseport_bpf_numa.c:138: undefined reference to `numa_run_on_node' /tmp/ccfUuExT.o: In function `main': /build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/net/reuseport_bpf_numa.c:230: undefined reference to `numa_available' /build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/net/reuseport_bpf_numa.c:233: undefined reference to `numa_max_node' It's GNU Make and linker specific. The default Makefile rule looks like: $(CC) $(CFLAGS) $(LDFLAGS) $@ $^ $(LDLIBS) When linking is done by gcc itself, no issue, but when it needs to be passed to proper ld, only LDLIBS follows and then ld cannot know what libs to link with. More detail: https://www.gnu.org/software/make/manual/html_node/Implicit-Variables.html LDFLAGS Extra flags to give to compilers when they are supposed to invoke the linker, ‘ld’, such as -L. Libraries (-lfoo) should be added to the LDLIBS variable instead. LDLIBS Library flags or names given to compilers when they are supposed to invoke the linker, ‘ld’. LOADLIBES is a deprecated (but still supported) alternative to LDLIBS. Non-library linker flags, such as -L, should go in the LDFLAGS variable. https://lkml.org/lkml/2010/2/10/362 tools/perf: libraries must come after objects Link order matters, use LDLIBS instead of LDFLAGS to properly link against libnuma. Signed-off-by:
-
Andrew Lunn authored
[ Upstream commit 7ae710f9 ] On SoC reset all GPIO interrupts are disable. However, if kexec is used to boot into a new kernel, the SoC does not experience a reset. Hence GPIO interrupts can be left enabled from the previous kernel. It is then possible for the interrupt to fire before an interrupt handler is registered, resulting in the kernel complaining of an "unexpected IRQ trap", the interrupt is never cleared, and so fires again, resulting in an interrupt storm. Disable all GPIO interrupts before registering the GPIO IRQ chip. Fixes: 7f2691a1 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid") Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Acked-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
-
Florian Westphal authored
[ Upstream commit 2035f3ff ] Unlike ip(6)tables ebtables only counts user-defined chains. The effect is that a 32bit ebtables binary on a 64bit kernel can do 'ebtables -N FOO' only after adding at least one rule, else the request fails with -EINVAL. This is a similar fix as done in 3f1e53ab ("netfilter: ebtables: don't attempt to allocate 0-sized compat array"). Fixes: 7d7d7e02 ("netfilter: compat: reject huge allocation requests") Reported-by:
Francesco Ruggeri <fruggeri@arista.com> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Alexey Khoroshilov authored
[ Upstream commit c69c29a1 ] If phy_power_on() fails in rk_gmac_powerup(), clocks are left enabled. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Yonglong Liu authored
[ Upstream commit cec8abba ] When reading phy registers via Clause 45 MDIO protocol, after write address operation, the driver use another write address operation, so can not read the right value of any phy registers. This patch fixes it. Signed-off-by:
Yonglong Liu <liuyonglong@huawei.com> Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
-
