The PNoC clock is a clock for the entire PNoC bus, managed from
within the interconnect driver. Attaching it to MSS was a total hack.
Get rid of it and take the liberty to make the clock-names entries
more readable.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-9-a66e698932e3@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The AGGRE2 clock is a clock for the entire AGGRE2 bus, managed from
within the interconnect driver. Attaching it to SLPI was a total hack.
Get rid of it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-8-a66e698932e3@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The AGGRE2 clock is a clock for the entire AGGRE2 bus, managed from
within the interconnect driver. Attaching it to SLPI was a total hack.
Get rid of it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-7-a66e698932e3@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some nodes are abusingly referencing some of the internal bus clocks,
that were recently removed in Linux (because the original implementation
did not make much sense), managing them as if they were the only devices
on an NoC bus.

These clocks are now handled from within the icc framework and are
no longer registered from within the CCF. Remove them.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-6-a66e698932e3@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some nodes are abusingly referencing some of the internal bus clocks,
that were recently removed in Linux (because the original implementation
did not make much sense), managing them as if they were the only devices
on an NoC bus.

These clocks are now handled from within the icc framework and are
no longer registered from within the CCF. Remove them.
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-5-a66e698932e3@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some nodes are abusingly referencing some of the internal bus clocks,
that were recently removed in Linux (because the original implementation
did not make much sense), managing them as if they were the only devices
on an NoC bus.

These clocks are now handled from within the icc framework and are
no longer registered from within the CCF. Remove them.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-4-a66e698932e3@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some nodes are abusingly referencing some of the internal bus clocks,
that were recently removed in Linux (because the original implementation
did not make much sense), managing them as if they were the only devices
on an NoC bus.

These clocks are now handled from within the icc framework and are
no longer registered from within the CCF. Remove them.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-3-a66e698932e3@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some nodes are abusingly referencing some of the internal bus clocks,
that were recently removed in Linux (because the original implementation
did not make much sense), managing them as if they were the only devices
on an NoC bus.

These clocks are now handled from within the icc framework and are
no longer registered from within the CCF. Remove them.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-2-a66e698932e3@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SDM660 was abusingly referencing one of the internal bus clocks, that
were recently dropped from Linux (because the original implementation
did not make much sense), circumventing the interconnect framework.

Drop it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-1-a66e698932e3@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For wakeup to work, driver needs to enable interrupts that depict what is
happening on the DP/DM lines. On QUSB targets, this is identified by
qusb2_phy whereas on SoCs using Femto PHY, separate {dp,dm}_hs_phy_irq's
are used instead.

The implementation incorrectly names qusb2_phy interrupts as "hs_phy_irq".
Clean this up so that driver would be using only qusb2/(dp & dm) for wakeup
purposes.

For devices running older kernels, this won't break any functionality
because the interrupt configurations in QUSB2 PHY based SoCs is done
by configuring QUSB2PHY_INTR_CTRL register in PHY address space and it was
never armed properly right from the start.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231227091951.685-3-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The high speed related interrupts present on QC targets are as follows:

1. dp/dm irq's
These IRQ's directly reflect changes on the DP/DM pads of the SoC. These
are used as wakeup interrupts only on SoCs with non-QUSB2 targets with
exception of SDM670/SDM845/SM6350.

2. qusb2_phy irq
SoCs with QUSB2 PHY do not have separate DP/DM IRQs and expose only a
single IRQ whose behavior can be modified by the QUSB2PHY_INTR_CTRL
register. The required DPSE/DMSE configuration is done in
QUSB2PHY_INTR_CTRL register of phy address space.

3. hs_phy_irq
This is completely different from the above two and is present on all
targets with exception of a few IPQ ones. The interrupt is not enabled by
default and its functionality is mutually exclusive of qusb2_phy on QUSB
targets and DP/DM on femto phy targets.

The DTs of several QUSB2 PHY based SoCs incorrectly define "hs_phy_irq"
when they should have been "qusb2_phy_irq". On Femto phy targets, the
"hs_phy_irq" mentioned is either the actual "hs_phy_irq" or "pwr_event",
neither of which would never be triggered directly are non-functional
currently. The implementation tries to clean up this issue by addressing
the discrepencies involved and fixing the hs_phy_irq's in respective DT's.

Classify SoC's into four groups based on whether qusb2_phy interrupt
or {dp/dm}_hs_phy_irq is used for wakeup in high speed and whether the
SoCs have hs_phy_irq present in them or not. The ss_phy_irq is optional
interrupt because there are mutliple SoC's which either support only High
Speed or there are multiple controllers within same Soc and the secondary
controller is High Speed only capable.

This breaks ABI on targets running older kernels, but since the interrupt
definitions are given wrong on many targets and to establish proper rules
for usage of DWC3 interrupts on Qualcomm platforms, DT binding update is
necessary. The bindings put pwr_event as the first interrupt and ss_phy as
the last. Since all SoCs have the pwr_event (HS) interrupt, but not all
controllers have the SS PHY interrupt, this would prevent, to some extent,
expressing that the SS PHY is optional by keeping it last in the binding
schema and making sure that minItems = maxItems - 1.

No new targets have been added to schema. Only the existing ones have been
re-ordered.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231227091951.685-2-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In 6.7-rc1, there was a netif_device_detach call added to the
gether_disconnect function. This clears the __LINK_STATE_PRESENT bit of
the netif device and suppresses pings (ICMP messages) and TCP connection
requests from the connected host. If userspace temporarily disconnects
the gadget, such as by temporarily removing configuration in the gadget
configfs interface, network activity should continue to be processed
when the gadget is re-connected. Mirror the netif_device_detach call
with a netif_device_attach call in gether_connect to fix re-connecting
gadgets.

Link: https://gitlab.com/postmarketOS/pmaports/-/tree/6002e51b7090aeeb42947e0ca7ec22278d7227d0/main/postmarketos-base-ui/rootfs-usr-lib-NetworkManager-dispatcher.d-50-tethering.sh
Cc: stable <stable@kernel.org>
Fixes: f49449fb ("usb: gadget: u_ether: Replace netif_stop_queue with netif_device_detach")
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Tested-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20231218164532.411125-2-mailingradian@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a scenario where DWC3 runtime suspend is blocked due to the
dwc->connected flag still being true while PM usage_count is zero after
DWC3 giveback is completed and the USB gadget session is being terminated.
This leads to a case where nothing schedules a PM runtime idle for the
device.

The exact condition is seen with the following sequence:
  1.  USB bus reset is issued by the host
  2.  Shortly after, or concurrently, a USB PD DR SWAP request is received
      (sink->source)
  3.  USB bus reset event handler runs and issues
      dwc3_stop_active_transfers(), and pending transfer are stopped
  4.  DWC3 usage_count decremented to 0, and runtime idle occurs while
      dwc->connected == true, returns -EBUSY
  5.  DWC3 disconnect event seen, dwc->connected set to false due to DR
      swap handling
  6.  No runtime idle after this point

Address this by issuing an asynchronous PM runtime idle call after the
disconnect event is completed, as it modifies the dwc->connected flag,
which is what blocks the initial runtime idle.

Fixes: fc8bb91b ("usb: dwc3: implement runtime PM")
Cc:  <stable@vger.kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240103214946.2596-1-quic_wcheng@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When CONFIG_USB_OTG is not set, mxs_phy_is_otg_host() will always return
false. This behaviour is wrong. Since phy.last_event will always be set
for either host or device mode. Therefore, CONFIG_USB_OTG condition
can be removed.

Fixes: 5eda42ae ("usb: phy: mxs: fix getting wrong state with mxs_phy_is_otg_host()")
cc:  <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20231228110753.1755756-3-xu.yang_2@nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After the chipidea driver introduce extcon for id and vbus, it's able
to wakeup from another irq source, in case the system with extcon ID
cable, wakeup from usb ID cable and device removal, the usb device
disconnect irq may come firstly before the extcon notifier while system
resume, so we will get 2 "wakeup" irq, one for usb device disconnect;
and one for extcon ID cable change(real wakeup event), current driver
treat them as 2 successive wakeup irq so can't handle it correctly, then
finally the usb irq can't be enabled. This patch adds a check to bypass
further usb events before controller resume finished to fix it.

Fixes: 1f874edc ("usb: chipidea: add runtime power management support")
cc:  <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20231228110753.1755756-2-xu.yang_2@nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some platform using ChipIdea IP  may keep 32KHz wakeup clock always
on without usb driver intervention. And some may need driver to handle
this clock. For now only i.MX93 needs this wakeup clock. This patch will
get wakeup clock and keep it always on to make controller work properly.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20231228110753.1755756-1-xu.yang_2@nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 3c5b006f.

gadget_is_{super|dual}speed() API check UDC controller capitblity. It
should pass down highest speed endpoint descriptor to UDC controller. So
UDC controller driver can reserve enough resource at check_config(),
especially mult and maxburst. So UDC driver (such as cdns3) can know need
at least (mult + 1) * (maxburst + 1) * wMaxPacketSize internal memory for
this uvc functions.

Cc:  <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-5-Frank.Li@nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Supposed DMA cross 4k bounder problem should be fixed at DEV_VER_V2, but
still met problem when do ISO transfer if sg enabled.

Data pattern likes below when sg enabled, package size is 1k and mult is 2
	[UVC Header(8B) ] [data(3k - 8)] ...

The received data at offset 0xd000 will get 0xc000 data, len 0x70. Error
happen position as below pattern:
	0xd000: wrong
	0xe000: wrong
	0xf000: correct
	0x10000: wrong
	0x11000: wrong
	0x12000: correct
	...

To avoid DMA cross 4k bounder at ISO transfer, reduce burst len according
to start DMA address's alignment.

Cc:  <stable@vger.kernel.org>
Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-4-Frank.Li@nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ISO basic transfer is
	ITP(SOF) Package_0 Package_1 ... Package_n

CDNS3 DMA start dma transfer from memmory to internal FIFO when get SOF,
controller will transfer data to usb bus from internal FIFO when get IN
token.

According USB spec defination:
	Maximum number of packets = (bMaxBurst + 1) * (Mult + 1)

Internal memory should be the same as (bMaxBurst + 1) * (Mult + 1). DMA
don't fetch data advance when ISO transfer, so only reserve
(bMaxBurst + 1) * (Mult + 1) internal memory for ISO transfer.

Need save Mult and bMaxBurst information and set it into EP_CFG register,
otherwise only 1 package is sent by controller, other package will be
lost.

Cc:  <stable@vger.kernel.org>
Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-3-Frank.Li@nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When IP version >= DEV_VER_V2, gadget:sg_supported is true. So uvc gadget
function driver will use sg to equeue data, first is 8bytes header, the
second is 1016bytes data.

    cdns3_prepare_trb: ep2in: trb 0000000000ac755f, dma buf: 0xbf455000, size: 8, burst: 128 ctrl: 0x00000415 (C=1, T=0, ISP, CHAIN, Normal)
    cdns3_prepare_trb: ep2in: trb 00000000a574e693, dma buf: 0xc0200fe0, size: 1016, burst: 128 ctrl: 0x00000405 (C=1, T=0, ISP, Normal)

But cdns3_ep_run_transfer() can't correctly handle this case, which only
support one TRB for ISO transfer.

The controller requires duplicate the TD for each SOF if priv_ep->interval
is not 1. DMA will read data from DDR to internal FIFO when get SOF. Send
data to bus when receive IN token. DMA always refill FIFO when get SOF
regardless host send IN token or not. If host send IN token later, some
frames data will be lost.

Fixed it by below major steps:

1. Calculate numembers of TRB base on sg_nums and priv_ep->interval.
2. Remove CHAIN flags for each end TRB of TD when duplicate TD.
3. The controller requires LINK TRB must be first TRB of TD. When check
there are not enough TRBs lefts, just fill LINK TRB for left TRBs.

.... CHAIN_TRB DATA_TRB, CHAIN_TRB DATA_TRB,  LINK_TRB ... LINK_TRB
                                                           ^End of TRB List

Cc:  <stable@vger.kernel.org>
Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-2-Frank.Li@nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The max segment size is currently limited to the ethernet frame length of
the kernel which happens to be 1514 at this point in time. However the NCM
specification limits it to 64K for sixtenn bit NTB's. For peer to peer
connections, increasing the segment size gives better throughput.

Add support to configure this value before configfs symlink is created.
Also since the NTB Out/In buffer sizes are fixed at 16384 bytes, limit the
segment size to an upper cap of 8000 to allow at least a minimum of 2 MTU
sized datagrams to be aggregated.

Set the default MTU size for the ncm interface during function bind before
network interface is registered allowing MTU to be set in parity with
wMaxSegmentSize.

Update gadget documentation describing the new configfs property.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/20231221153216.18657-1-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For device mode, if PM runtime autosuspend feature enabled, the
runtime power status of dwc3 may be suspended when run dwc3_resume(),
and dwc3 gadget would not be configured in dwc3_gadget_run_stop().
It would cause gadget connected failed if USB cable has been plugged
before PM resume. So move forward pm_runtime_set_active() to fix it.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Link: https://lore.kernel.org/r/20231206065939.16958-1-frank.wang@rock-chips.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Support configuration and use of bulk endpoints in the so-called EBC
mode described in the DBC_usb31 databook (appendix E)

Added a bit fifo_mode to usb_ep to indicate to the UDC driver that a
specific endpoint is to operate in the EBC (or equivalent) mode when
enabled

Added macros for bits 15 and 14 of DEPCFG parameter 1 to indicate EBC
mode and write back behaviour. These bits will be set to 1 when
configuring an EBC endpoint as described in the programming guide
Signed-off-by: Manan Aurora <maurora@google.com>
Link: https://lore.kernel.org/r/20231031034641.660606-1-maurora@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor tcpm_fw_get_caps to support the multiple pd capabilities got
from fwnode. For backward compatibility, the original single capability
is still applicable. The fetched data is stored in the newly defined
structure "pd_data" and there is an array "pd_list" to store the
pointers to them. A dedicated array "pds" is used to store the handles
of the registered usb_power_delivery instances.

Also implement the .pd_get and .pd_set ops which are introduced in
commit a7cff92f ("usb: typec: USB Power Delivery helpers for ports
and partners"). Once the .pd_set is called, the current capability will
be updated and state machine will re-negotiate the power contract if
possible.
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231216104630.2720818-3-kyletso@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 662a6010 ("usb: typec: Separate USB Power Delivery from USB
Type-C") allows userspace to configure the PD of a port by selecting
different set of predefined PD capabilities. Define the PD capability
sets in DT for better configurability in device modules.

Define an optional child node "capabilities" to contain multiple USB
Power Delivery capabilities.

Define child nodes with pattern (e.g. caps-0, caps-1) under
"capabilities". Each node contains PDO data of a selectable Power
Delivery capability.

Also define common properties for source-pdos, sink-pdos, and
op-sink-microwatt that can be referenced.
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20231205030114.1349089-2-kyletso@google.comSigned-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231216104630.2720818-2-kyletso@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The xhci retaining bogus hardware states cause usb disconnect devices
connected before hibernation(s4) and refer to the commit 'f3d47885
("usb: ohci-platform: fix usb disconnect issue after s4")' which set
flag "hibernated" as true when resume-from-hibernation and that the
drivers will reset the hardware to get rid of any existing state and
make sure resume from hibernation re-enumerates everything for xhci.
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Link: https://lore.kernel.org/r/20231228071113.1719-1-zhuyinbo@loongson.cnSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently for dwc3_usb31 controller, if maximum_speed is limited to
super-speed in DT, then device mode is limited to SS, but host mode
still works in SSP.

The documentation for max-speed property is as follows:

"Tells USB controllers we want to work up to a certain speed.
Incase  this isn't passed via DT, USB controllers should default to
their maximum HW capability."

It doesn't specify that the property is only for device mode.
There are cases where we need to limit the host's maximum speed to
SuperSpeed only. Use this property for host mode to contrain host's
speed to SuperSpeed.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231219041559.15789-1-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Current implementation blocks the running operations when Plug-out and
Plug-In is performed continuously, process gets stuck in
dwc3_thread_interrupt().

Code Flow:

	CPU1

	->Gadget_start
	->dwc3_interrupt
	->dwc3_thread_interrupt
	->dwc3_process_event_buf
	->dwc3_process_event_entry
	->dwc3_endpoint_interrupt
	->dwc3_ep0_interrupt
	->dwc3_ep0_inspect_setup
	->dwc3_ep0_stall_and_restart

By this time if pending_list is not empty, it will get the next request
on the given list and calls dwc3_gadget_giveback which will unmap request
and call its complete() callback to notify upper layers that it has
completed. Currently dwc3_gadget_giveback status is set to -ECONNRESET,
whereas it should be -ESHUTDOWN based on condition if not dwc->connected
is true.

Cc:  <stable@vger.kernel.org>
Fixes: d742220b ("usb: dwc3: ep0: giveback requests on stall_and_restart")
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20231222094704.20276-1-quic_uaggarwa@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A freezable kernel thread can enter frozen state during freezing by
either calling try_to_freeze() or using wait_event_freezable() and its
variants. So for the following snippet of code in a kernel thread loop:
  wait_event_interruptible_timeout();
  try_to_freeze();

We can change it to a simple wait_event_freezable_timeout() and
then eliminate a function call.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20231218074730.1898699-1-haokexin@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Current EP0 dequeue path will share the same as other EPs.  However, there
are some special considerations that need to be made for EP0 transfers:

  - EP0 transfers never transition into the started_list
  - EP0 only has one active request at a time

In case there is a vendor specific control message for a function over USB
FFS, then there is no guarantee on the timeline which the DATA/STATUS stage
is responded to.  While this occurs, any attempt to end transfers on
non-control EPs will end up having the DWC3_EP_DELAY_STOP flag set, and
defer issuing of the end transfer command.  If the USB FFS application
decides to timeout the control transfer, or if USB FFS AIO path exits, the
USB FFS driver will issue a call to usb_ep_dequeue() for the ep0 request.

In case of the AIO exit path, the AIO FS blocks until all pending USB
requests utilizing the AIO path is completed.  However, since the dequeue
of ep0 req does not happen properly, all non-control EPs with the
DWC3_EP_DELAY_STOP flag set will not be handled, and the AIO exit path will
be stuck waiting for the USB FFS data endpoints to receive a completion
callback.

Fix is to utilize dwc3_ep0_reset_state() in the dequeue API to ensure EP0
is brought back to the SETUP state, and ensures that any deferred end
transfer commands are handled.  This also will end any active transfers
on EP0, compared to the previous implementation which directly called
giveback only.

Fixes: fcd2def6 ("usb: dwc3: gadget: Refactor dwc3_gadget_ep_dequeue")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231206201814.32664-1-quic_wcheng@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Unlock before returning on the error path.

Fixes: 86b20af1 ("usb: yurex: Replace snprintf() with the safer scnprintf() variant")
Reported-by: Dan Carpenter <error27@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202312170252.3udgrIcP-lkp@intel.com/Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20231219063639.450994-1-harshit.m.mogalapalli@oracle.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The TPS6598x PD controller supports firmware updates that can be loaded
either from an external flash memory or a host using the device's I2C
host interface. This patch implements the second approach, which is
especially relevant if no flash memory is available.

In order to make patch bundle updates, a series of tasks (special
commands) must be sent to the device as it is documented in the
TPS65987DDH and TPS65988DH Host Interface Technical Reference Manual[1],
section 4.11 (Patch Bundle Update Tasks).

The update sequence is as follows:
1. PTCs - Start Patch Load Sequence: the proposed approach includes
   device and application configuration data.
2. PTCd - Patch Download: 64-byte data chunks must be sent until the end
   of the firmware file is reached (the last chunk may be shorter).
3. PTCc - Patch Data Transfer Complete: ends the patch loading sequence.

After this sequence and if no errors occurred, the device will change
its mode to 'APP' after SETUP_MS milliseconds, and then it will be ready
for normal operation.

[1] https://www.ti.com/lit/ug/slvubh2b/slvubh2b.pdf?ts=1697623299919&ref_url=https%253A%252F%252Fwww.ti.com%252Fproduct%252FTPS65987DSigned-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231207-tps6598x_update-v2-4-f3cfcde6d890@wolfvision.netSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The input data passed to execute commands with tps6598x_exec_cmd()
is not supposed to be modified by the function. Moreover, this data is
passed to tps6598x_exec_cmd_tmo() and finally to tps6598x_block_write(),
which expects a const pointer.

The current implementation does not produce any bugs, but it discards
const qualifiers from the pointers passed as arguments. This leads to
compile issues if 'discarded-qualifiers' is active and a const pointer
is passed to the function, which is the case if data from a firmware
structure is passed to execute update commands. Adding the const
modifier to in_data prevents such issues and provides code consistency.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231207-tps6598x_update-v2-3-f3cfcde6d890@wolfvision.netSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The firmware request process is device agnostic and can be used for
other parts.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231207-tps6598x_update-v2-2-f3cfcde6d890@wolfvision.netSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The current implementation includes a number of special cases for the
tps25750. Nevertheless, init and reset functions can be generalized by
adding function pointers to the tipd_data structure in order to offer
that functionality to other parts without additional conditional
clauses.

Some functionality like the cold reset request (GAID) is shared by the
tps25750 and the tps6598x, so they can use the same reset function.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231207-tps6598x_update-v2-1-f3cfcde6d890@wolfvision.netSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix spelling typo in comments.
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: liyouhong <liyouhong@kylinos.cn>

Link: https://lore.kernel.org/r/20231221023425.1316397-1-liyouhong@kylinos.cnSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit e835c0a4.

Don't omit soft-reset. During initialization, the driver may need to
perform a soft reset to ensure the phy is ready when the controller
updates the GCTL.PRTCAPDIR or other settings by issuing phy soft-reset.
Many platforms often have access to DCTL register for soft-reset despite
being host-only. If there are actual reported issues from the platforms
that don't expose DCTL registers, then we will need to revisit (perhaps
to teach dwc3 to perform xhci's soft-reset USBCMD.HCRST).

Cc:  <stable@vger.kernel.org>
Fixes: e835c0a4 ("usb: dwc3: don't reset device side if dwc3 was configured as host-only")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/7668ab11a48f260820825274976eb41fec7f54d1.1703282469.git.Thinh.Nguyen@synopsys.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 8bea147d.

The phy soft reset GUSB2PHYCFG.PHYSOFTRST only applies to UTMI phy, not
ULPI. This fix is incomplete.

Cc:  <stable@vger.kernel.org>
Fixes: 8bea147d ("usb: dwc3: Soft reset phy on probe for host")
Reported-by: Köry Maincent <kory.maincent@bootlin.com>
Closes: https://lore.kernel.org/linux-usb/20231205151959.5236c231@kmaincent-XPS-13-7390Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/29a26593a60eba727de872a3e580a674807b3339.1703282469.git.Thinh.Nguyen@synopsys.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The DWC2 IP on the Rockchip SoCs doesn't support clock gating.
When a clock gating is enabled, system hangs.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/1703575199-23638-1-git-send-email-william.wu@rock-chips.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit b17b7fe6.

That commit messed up the reference counting, so it needs to
be rethought.

Fixes: b17b7fe6 ("usb: typec: class: fix typec_altmode_put_partner to put plugs")
Cc:  <stable@vger.kernel.org>
Cc: RD Babiera <rdbabiera@google.com>
Reported-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Closes: https://lore.kernel.org/lkml/CAP-bSRb3SXpgo_BEdqZB-p1K5625fMegRZ17ZkPE1J8ZYgEHDg@mail.gmail.com/Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240102091142.2136472-1-heikki.krogerus@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>