- 01 Jul, 2011 18 commits
-
-
Jarod Wilson authored
With hardware that has to use ir_raw_event_store_edge to collect IR sample durations, we were not doing an event reset unless IR_MAX_DURATION had passed. That's around 4 seconds. So if someone presses up, then down, with less than 4 seconds in between, they'd get the initial up, then up and down upon pressing down. To fix this, I've lowered the "send a reset event" logic's threshold to the input device's REP_DELAY (defaults to 500ms), and with an saa7134-based GPIO-driven IR receiver in a Hauppauge HVR-1150, I get *much* better behavior out of the remote now. Special thanks to Devin for providing the hardware to investigate this issue. CC: stable@kernel.org CC: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jarod Wilson authored
There's really no good reason not to just grab the desired IRQ at driver init time, instead of every time the lirc device node is accessed. This also improves the speed and reliability with which a serial transmitter can operate, as back-to-back transmission attempts (i.e., channel change to a multi-digit channel) don't have to spend time acquiring and then releasing the IRQ for every digit, sometimes multiple times, if lircd has been told to use the min_repeat parameter. CC: devel@driverdev.osuosl.org Signed-off-by:
-
Jarod Wilson authored
We were calling schedule_timeout with the rx thread's task state still at TASK_RUNNING, which it shouldn't be. Make sure we call set_current_state(TASK_INTERRUPTIBLE) *before* schedule_timeout, and we're all good here. I believe this problem was mistakenly introduced in commit 5bd6b046, and I'm not sure how I missed it before, as I swear I tested the patchset that was included in, but alas, stuff happens... Acked-by:
Andy Walls <awalls@md.metrocast.net> CC: stable@kernel.org Signed-off-by:
-
Jarod Wilson authored
Both consumers of RC_MAP_PINNACLE_PCTV_HD send along full RC-5 scancodes, so this update makes this keymap actually *have* full scancodes, heisted from rc-dib0700-rc5.c. This should fix out of the box remote functionality for the Pinnacle PCTV HD 800i (cx88 pci card) and PCTV HD Pro 801e (em28xx usb stick). CC: stable@kernel.org Signed-off-by:
-
Jarod Wilson authored
Thanks to the intrepid testing and debugging of Matthijs van Drunen, it was uncovered that at least some variants of the ITE8709 need to use pnp resource 2, rather than 0, for things to function properly. Resource 0 has a length of only 1, and if you try to bypass the pnp_port_len check and use it anyway (with either a length of 1 or 2), the system in question's trackpad ceased to function. The circa lirc 0.8.7 lirc_ite8709 driver used resource 2, but the value was (amusingly) changed to 0 by way of a patch from ITE themselves, so I don't know if there may be variants where 0 actually *is* correct, but at least in this case and in the original lirc_ite8709 driver author's case, it sure looks like 2 is the right value. This fix should probably be applied to all stable kernels with the ite-cir driver, lest we nuke more people's trackpads. Tested-by: Matthijs van Drunen CC: Juan Jesús García de Soria <skandalfo@gmail.com> CC: stable@kernel.org Signed-off-by:
-
Andre Bartke authored
mx1_camera_add_device() can return an uninitialized value of ret. Signed-off-by:
Andre Bartke <andre.bartke@gmail.com> [g.liakhovetski@gmx.de: modified the fix to remove "ret" completely] Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Vaibhav Hiremath authored
The usecase where, user allocates small size of buffer through bootargs (video1_bufsize/video2_bufsize) and later from application tries to set the format which requires larger buffer size, driver doesn't check for insufficient buffer size and allows application to map extra buffer. This leads to kernel crash, when user application tries to access memory beyond the allocation size. Added check in both mmap and reqbuf call back function, and return error if the size of the buffer allocated by user through bootargs is less than the S_FMT size. Signed-off-by:
Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by:
-
Vaibhav Hiremath authored
With addition of media-controller framework, now we have various device nodes (/dev/videoX) getting created, so hardcoding minor number in video_register_device() is not recommended. So let V4L2 framework choose free minor number for the device. Signed-off-by: -
Vladimir Pantelic authored
The omap_vout_new_crop() function has possible bug, uses uninitialized variable "crop.width/height" which is actually output of the function. Instead we should be using "try_crop.width/height" to calculate the resizer value. Signed-off-by:
Vladimir Pantelic <vladoman@gmail.com> Signed-off-by:
-
Sjoerd Simons authored
When failing to start the camera we should disable the queue again, to rollback into the same initial state. Otherwise re-trying will always hit -EBUSY Signed-off-by:
Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Sjoerd Simons authored
When freeing memory for the video buffers also remove them from the irq & main queues. This fixes an oops when doing the following: open ("/dev/video", ..) VIDIOC_REQBUFS VIDIOC_QBUF VIDIOC_REQBUFS close () As the second VIDIOC_REQBUFS will cause the list entries of the buffers to be cleared while they still hang around on the main and irc queues Signed-off-by: -
Laurent Pinchart authored
If a streaming interface has no supported format, the driver won't create a video device for the associated terminal. Fix an oops by ignoring that terminal when creating links between entities. Signed-off-by:
-
Laurent Pinchart authored
Entities associated with video device nodes are unregistered in video_unregister_device(). This destroys the entity even though it can still be accessed through open video device nodes. Move the media_device_unregister_entity() call from video_unregister_device() to v4l2_device_release() to ensure that the entity isn't unregistered until the last reference to the video device is released. Also remove the media_entity_get()/put() calls from v4l2-dev.c. Those functions were designed for subdevs, to avoid a parent module from being removed while still accessible through board code. They're not currently needed for video device nodes, and will oops when a hotpluggable device is disconnected during streaming, as media_entity_put() called in v4l2_device_release() tries to access entity->parent->dev->driver which is set to NULL when the device is disconnected. Signed-off-by:
Sakari Ailus <sakari.ailus@iki.fi> Acked-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Ohad Ben-Cohen authored
Fix a potential NULL pointer dereference by skipping registration of external entities in case none are provided. This is useful at least when testing mere memory-to-memory scenarios. Signed-off-by:
Ohad Ben-Cohen <ohad@wizery.com> Acked-by:
-
Marek Szyprowski authored
__vb2_queue_alloc function returns the number of successfully allocated buffers. There is no point in checking if the returned value is negative. If this function returns 0, videobuf2 should just return -ENOMEM to userspace, because no driver can work without memory buffers. Reported-by:
Jonathan Corbet <corbet@lwn.net> Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> CC: Pawel Osciak <pawel@osciak.com> Signed-off-by:
-
Marek Szyprowski authored
queued_count variable was left untouched during the queue reinitialization in __vb2_queue_cancel, what might lead to mismatch between the real number of queued buffers and queued_count variable. Reported-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Marek Szyprowski authored
This reverts commit 31901a07. Queue should be reinitialized on each REQBUFS() call even if the memory access method and buffer count have not been changed. The user might have changed the format and if we go the short path introduced in that commit, the memory buffer will not be reallocated to fit with new format. The previous patch was just over-engineered optimization, which just introduced a bug to videobuf2. Reported-by:
-
Marek Szyprowski authored
Add __GFP_NOWARN parameter to videobuf2 dma-sg allocator to prevent kernel warning and stack dump if there is not enough memory available. Videobuf2 and drivers should correctly handle no memory case, so there is no need for stack dump and extensive log. Signed-off-by:
-
- 21 Jun, 2011 1 commit
-
-
Hans de Goede authored
Unplugging a pwc cam while an app has the /dev/video# node open leads to an oops in pwc_video_close when the app closes the node, because the disconnect handler has free-ed the pdev struct pwc_video_close tries to use. Instead of adding some sort of bandaid for this. fix it properly using the v4l2 core's new(ish) behavior of keeping the v4l2_dev structure around until both unregister has been called, and all file handles referring to it have been closed: Embed the v4l2_dev structure in the pdev structure and define a v4l2 dev release callback releasing the pdev structure (and thus also the embedded v4l2 dev structure. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Cc: stable@kernel.org Signed-off-by:
-
- 11 Jun, 2011 21 commits
-
-
Marek Szyprowski authored
Add maintainers for the videobuf2 V4L2 driver framework. Signed-off-by:
Pawel Osciak <pawel@osciak.com> Signed-off-by:
-
HeungJun, Kim authored
Signed-off-by:
HeungJun, Kim <riverful.kim@samsung.com> Signed-off-by:
-
HeungJun, Kim authored
Remove union version in the m5mols_get_version(), and read version information directly. Also remove VERSION_SIZE. Signed-off-by:
-
HeungJun, Kim authored
For now, the m5mols_read() share in case of I2C packet 1, 2, 4 byte(s) width. So, this commit adds 3 functions - m5mols_read_u8/u16/u32() according to byte width of I2C packet. And, the u32 variables in spite of u8 or u16 for fitting to m5mols_read() having no choice, is replaced to have original byte width like u8, u16, u32 as same reason. Signed-off-by:
-
HeungJun, Kim authored
The main capture and the thumbnail image size registers were erroneously defined to have 1 byte width, resulting in wrong reported image size. Fix this by changing the registers width to correct value. Reported-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
-
Sylwester Nawrocki authored
Signed-off-by:
-
Sylwester Nawrocki authored
With multi-planar formats fmt.pix_mp member of struct v4l2_format should be used rather than fmt.pix. Fix find_fmt() function to do the right thing. Signed-off-by:
-
Sylwester Nawrocki authored
The buf_init buffer queue operation is optional and buffer_init() does nothing, remove it. Signed-off-by:
-
Sylwester Nawrocki authored
Avoid dereferencing of NULL f->fmt. Correct size of the allocated buffer in case the crop rectangle is smaller than the bounds rectangle (configured with S_FMT). Also remove redundant check for *num_buffer == 0 as this case is handled in videobuf2. Signed-off-by:
-
Sylwester Nawrocki authored
Correct inconsistencies in data structures' documentation. Remove meaningless debug traces. Signed-off-by:
-
Sylwester Nawrocki authored
Remove V4L2_MBUS_FMT_RGB565_2X8_BE media code entry as camera interface supports only packed YUYV formats. Signed-off-by:
-
Sylwester Nawrocki authored
Add missing kfree on the error path. Reported-by:
Tomasz Stanislawski <t.stanislaws@samsung.com> Signed-off-by:
-
Jarod Wilson authored
As pointed out on the lirc list by Andreas Dick, initial panel key repeat suppression wasn't working, as we had no timevals accumulated until after the first repeat. Also add a missing locking call. Signed-off-by:
-
Jarod Wilson authored
Courtesy of information from Andreas Dick on the lirc list. Signed-off-by:
-
Jarod Wilson authored
Hans Petter Selasky pointed out to me that we're leaking urbs when mce_async_out is called. Its used both for configuring the hardware and for transmitting IR data. In the tx case, mce_request_packet actually allocates both a urb and the transfer buffer, neither of which was being torn down. Do that in the tx callback. CC: Hans Petter Selasky <hselasky@c2i.net> Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
There was a missing lock in fintek_suspend. Without the lock, its possible the system will be in the middle of receiving IR (draining the RX buffer) when we try to disable CIR interrupts. Signed-off-by:
-
Jarod Wilson authored
Store the cdev pointer in struct irctl, allocated dynamically as needed, rather than having a static array. At the same time, recycle some of the saved memory to nudge the maximum number of lirc devices supported up a ways -- its not that uncommon these days, now that we have the rc-core lirc bridge driver, to see a system with at least 4 raw IR receivers. (consider a mythtv backend with several video capture devices and the possible need for IR transmit hardware). Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Aside from the initial "hey, lets make sure we've flushed any pre-existing data on the device" call to mce_sync_in, every other one of the calls was entirely superfluous. Ergo, remove them all, and rename the one and only (questionably) useful one to reflect what it really does. Verified on both gen2 and gen3 hardware to make zero difference. Well, except that you no longer get a bunch of urb submit failures from the unneeded mce_sync_in calls. Oh. And move that flush to a point *after* we've wired up the inbound urb, or it won't do squat. I have half a mind to just remove it entirely, but someone thought it was necessary at some point, and it doesn't seem to hurt, so lets leave it for the time being. This excercise took place due to insightful questions asked by Hans Petter Selasky, about the possible reuse of the inbound urb before it was actually availble by mce_sync_in, so thanks to him for motivating this cleanup. Reported-by:
Hans Petter Selasky <hselasky@c2i.net> Signed-off-by:
-
