- 25 Jul, 2018 40 commits
-
-
Mathias Nyman authored
commit 229bc19f upstream. Don't rely on event interrupt (EINT) bit alone to detect pending port change in resume. If no change event is detected the host may be suspended again, oterwise roothubs are resumed. There is a lag in xHC setting EINT. If we don't notice the pending change in resume, and the controller is runtime suspeded again, it causes the event handler to assume host is dead as it will fail to read xHC registers once PCI puts the controller to D3 state. [ 268.520969] xhci_hcd: xhci_resume: starting port polling. [ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling. [ 268.521030] xhci_hcd: xhci_suspend: stopping port polling. [ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001 [ 268.521139] xhci_hcd: Port Status Change Event for port 3 [ 268.521149] xhci_hcd: resume root hub [ 268.521163] xhci_hcd: port resume event for port 3 [ 268.521168] xhci_hcd: xHC is not running. [ 268.521174] xhci_hcd: handle_port_status: starting port polling. [ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead The EINT lag is described in a additional note in xhci specs 4.19.2: "Due to internal xHC scheduling and system delays, there will be a lag between a change bit being set and the Port Status Change Event that it generated being written to the Event Ring. If SW reads the PORTSC and sees a change bit set, there is no guarantee that the corresponding Port Status Change Event has already been written into the Event Ring." Cc: <stable@vger.kernel.org> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Gautham R. Shenoy authored
commit b03897cf upstream. On 64-bit servers, SPRN_SPRG3 and its userspace read-only mirror SPRN_USPRG3 are used as userspace VDSO write and read registers respectively. SPRN_SPRG3 is lost when we enter stop4 and above, and is currently not restored. As a result, any read from SPRN_USPRG3 returns zero on an exit from stop4 (Power9 only) and above. Thus in this situation, on POWER9, any call from sched_getcpu() always returns zero, as on powerpc, we call __kernel_getcpu() which relies upon SPRN_USPRG3 to report the CPU and NUMA node information. Fix this by restoring SPRN_SPRG3 on wake up from a deep stop state with the sprg_vdso value that is cached in PACA. Fixes: e1c1cfed ("powerpc/powernv: Save/Restore additional SPRs for stop4 cpuidle") Cc: stable@vger.kernel.org # v4.14+ Reported-by:
Florian Weimer <fweimer@redhat.com> Signed-off-by:
Gautham R. Shenoy <ego@linux.vnet.ibm.com> Reviewed-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Al Viro authored
commit d202797f upstream. Doing iput() after path_put() is wrong. Cc: stable@vger.kernel.org Acked-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit f88a333b upstream. kernel_wait4() expects a userland address for status - it's only rusage that goes as a kernel one (and needs a copyout afterwards) [ Also, fix the prototype of kernel_wait4() to have that __user annotation - Linus ] Fixes: 92ebce5a ("osf_wait4: switch to kernel_wait4()") Cc: stable@kernel.org # v4.13+ Signed-off-by:
-
Alexander Couzens authored
[ Upstream commit 5c968f48 ] mii_nway_restart is not pm aware which results in a rtnl deadlock. Implement mii_nway_restart manual by setting BMCR_ANRESTART if BMCR_ANENABLE is set. To reproduce: * plug an asix based usb network interface * wait until the device enters PM (~5 sec) * `ip link set eth1 up` will never return Fixes: d9fe64e5 ("net: asix: Add in_pm parameter") Signed-off-by:
Alexander Couzens <lynxis@fe80.eu> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Sabrina Dubroca authored
[ Upstream commit e6651599 ] Commit adc176c5 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)") added enhanced DAD with a nonce length of 6 bytes. However, RFC7527 doesn't specify the length of the nonce, other than being 6 + 8*k bytes, with integer k >= 0 (RFC3971 5.3.2). The current implementation simply assumes that the nonce will always be 6 bytes, but others systems are free to choose different sizes. If another system sends a nonce of different length but with the same 6 bytes prefix, it shouldn't be considered as the same nonce. Thus, check that the length of the received nonce is the same as the length we sent. Ugly scapy test script running on veth0: def loop(): pkt=sniff(iface="veth0", filter="icmp6", count=1) pkt = pkt[0] b = bytearray(pkt[Raw].load) b[1] += 1 b += b'\xde\xad\xbe\xef\xde\xad\xbe\xef' pkt[Raw].load = bytes(b) pkt[IPv6].plen += 8 # fixup checksum after modifying the payload pkt[IPv6].payload.cksum -= 0x3b44 if pkt[IPv6].payload.cksum < 0: pkt[IPv6].payload.cksum += 0xffff sendp(pkt, iface="veth0") This should result in DAD failure for any address added to veth0's peer, but is currently ignored. Fixes: adc176c5 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)") Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Reviewed-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 9e3bff92 ] SYSTEMPORT Lite reversed the logic compared to SYSTEMPORT, the GIB_FCS_STRIP bit is set when the Ethernet FCS is stripped, and that bit is not set by default. Fix the logic such that we properly check whether that bit is set or not and we don't forward an extra 4 bytes to the network stack. Fixes: 44a4524c ("net: systemport: Add support for SYSTEMPORT Lite") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Saeed Mahameed authored
[ Upstream commit 432e629e ] When a new rx packet arrives, the rx path will decide whether to reuse the remainder of the page or not according to one of the below conditions: 1. frag_info->frag_stride == PAGE_SIZE / 2 2. frags->page_offset + frag_info->frag_size > PAGE_SIZE; The first condition is no met for when XDP is set. For XDP, page_offset is always set to priv->rx_headroom which is XDP_PACKET_HEADROOM and frag_info->frag_size is around mtu size + some padding, still the 2nd release condition will hold since XDP_PACKET_HEADROOM + 1536 < PAGE_SIZE, as a result the page will not be released and will be _wrongly_ reused for next free rx descriptor. In XDP there is an assumption to have a page per packet and reuse can break such assumption and might cause packet data corruptions. Fix this by adding an extra condition (!priv->rx_headroom) to the 2nd case to avoid page reuse when XDP is set, since rx_headroom is set to 0 for non XDP setup and set to XDP_PACKET_HEADROOM for XDP setup. No additional cache line is required for the new condition. Fixes: 34db548b ("mlx4: add page recycling in receive path") Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Suggested-by:
Martin KaFai Lau <kafai@fb.com> CC: Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Haiyang Zhang authored
[ Upstream commit 6b81b193 ] If out ring is full temporarily and receive completion cannot go out, we may still need to reschedule napi if certain conditions are met. Otherwise the napi poll might be stopped forever, and cause network disconnect. Fixes: 7426b1a5 ("netvsc: optimize receive completions") Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Sanjeev Bansal authored
[ Upstream commit 3a498606 ] This patch has fix for TX timeout while running bi-directional traffic with 100 Mbps using 5762. Signed-off-by:
Sanjeev Bansal <sanjeevb.bansal@broadcom.com> Signed-off-by:
Siva Reddy Kallam <siva.kallam@broadcom.com> Reviewed-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Matevz Vucnik authored
[ Upstream commit 38cd58ed ] This adds the USB id of LTE modem Quectel EG91. It requires the same quirk as other Quectel modems to make it work. Signed-off-by:
Matevz Vucnik <vucnikm@gmail.com> Acked-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Gustavo A. R. Silva authored
[ Upstream commit 9ba8376c ] It seems that a *break* is missing in order to avoid falling through to the default case. Otherwise, checking *chan* makes no sense. Fixes: 72df7a72 ("ptp: Allow reassigning calibration pin function") Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
[ Upstream commit df8ed346 ] Currently also the pause flags are removed from phydev->supported because they're not included in PHY_DEFAULT_FEATURES. I don't think this is intended, especially when considering that this function can be called via phy_set_max_speed() anywhere in a driver. Change the masking to mask out only the values we're going to change. In addition remove the misleading comment, job of this small function is just to adjust the supported and advertised speeds. Fixes: f3a6bd39 ("phylib: Add phy_set_max_speed helper") Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
-
David Ahern authored
[ Upstream commit e7372197 ] Xin reported that icmp replies may not use the address on the device the echo request is received if the destination address is broadcast. Instead a route lookup is done without considering VRF context. Fix by setting oif in flow struct to the master device if it is enslaved. That directs the lookup to the VRF table. If the device is not enslaved, oif is still 0 so no affect. Fixes: cd2fbe1b ("net: Use VRF device index for lookups on RX") Reported-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Stefano Brivio authored
[ Upstream commit e78bfb07 ] Commit 8b700862 ("net: Don't copy pfmemalloc flag in __copy_skb_header()") introduced a different handling for the pfmemalloc flag in copy and clone paths. In __skb_clone(), now, the flag is set only if it was set in the original skb, but not cleared if it wasn't. This is wrong and might lead to socket buffers being flagged with pfmemalloc even if the skb data wasn't allocated from pfmemalloc reserves. Copy the flag instead of ORing it. Reported-by:
-
Stefano Brivio authored
[ Upstream commit 8b700862 ] The pfmemalloc flag indicates that the skb was allocated from the PFMEMALLOC reserves, and the flag is currently copied on skb copy and clone. However, an skb copied from an skb flagged with pfmemalloc wasn't necessarily allocated from PFMEMALLOC reserves, and on the other hand an skb allocated that way might be copied from an skb that wasn't. So we should not copy the flag on skb copy, and rather decide whether to allow an skb to be associated with sockets unrelated to page reclaim depending only on how it was allocated. Move the pfmemalloc flag before headers_start[0] using an existing 1-bit hole, so that __copy_skb_header() doesn't copy it. When cloning, we'll now take care of this flag explicitly, contravening to the warning comment of __skb_clone(). While at it, restore the newline usage introduced by commit b1937227 ("net: reorganize sk_buff for faster __copy_skb_header()") to visually separate bytes used in bitfields after headers_start[0], that was gone after commit a9e419dc ("netfilter: merge ctinfo into nfct pointer storage area"), and describe the pfmemalloc flag in the kernel-doc structure comment. This doesn't change the size of sk_buff or cacheline boundaries, but consolidates the 15 bits hole before tc_index into a 2 bytes hole before csum, that could now be filled more easily. Reported-by:
Patrick Talbert <ptalbert@redhat.com> Fixes: c93bdd0e ("netvm: allow skb allocation to use PFMEMALLOC reserves") Signed-off-by:
-
Lorenzo Colitti authored
[ Upstream commit acc2cf4e ] When tcp_diag_destroy closes a TCP_NEW_SYN_RECV socket, it first frees it by calling inet_csk_reqsk_queue_drop_and_and_put in tcp_abort, and then frees it again by calling sock_gen_put. Since tcp_abort only has one caller, and all the other codepaths in tcp_abort don't free the socket, just remove the free in that function. Cc: David Ahern <dsa@cumulusnetworks.com> Tested: passes Android sock_diag_test.py, which exercises this codepath Fixes: d7226c7a ("net: diag: Fix refcnt leak in error path destroying socket") Signed-off-by:
Lorenzo Colitti <lorenzo@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Reviewed-by:
David Ahern <dsa@cumulusnetworks.com> Tested-by:
-
Davidlohr Bueso authored
[ Upstream commit 107d01f5 ] rhashtable_init() currently does not take into account the user-passed min_size parameter unless param->nelem_hint is set as well. As such, the default size (number of buckets) will always be HASH_DEFAULT_SIZE even if the smallest allowed size is larger than that. Remediate this by unconditionally calling into rounded_hashtable_size() and handling things accordingly. Signed-off-by:
Davidlohr Bueso <dbueso@suse.de> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 83ed7d1f ] My randconfig builds came across an old missing dependency for ILA: ERROR: "dst_cache_set_ip6" [net/ipv6/ila/ila.ko] undefined! ERROR: "dst_cache_get" [net/ipv6/ila/ila.ko] undefined! ERROR: "dst_cache_init" [net/ipv6/ila/ila.ko] undefined! ERROR: "dst_cache_destroy" [net/ipv6/ila/ila.ko] undefined! We almost never run into this by accident because randconfig builds end up selecting DST_CACHE from some other tunnel protocol, and this one appears to be the only one missing the explicit 'select'. >From all I can tell, this problem first appeared in linux-4.9 when dst_cache support got added to ILA. Fixes: 79ff2fc3 ("ila: Cache a route to translated address") Cc: Tom Herbert <tom@herbertland.com> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Colin Ian King authored
[ Upstream commit 169dc027 ] The rol32 call is currently rotating hash but the rol'd value is being discarded. I believe the current code is incorrect and hash should be assigned the rotated value returned from rol32. Thanks to David Lebrun for spotting this. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Tyler Hicks authored
[ Upstream commit 70ba5b6d ] The low and high values of the net.ipv4.ping_group_range sysctl were being silently forced to the default disabled state when a write to the sysctl contained GIDs that didn't map to the associated user namespace. Confusingly, the sysctl's write operation would return success and then a subsequent read of the sysctl would indicate that the low and high values are the overflowgid. This patch changes the behavior by clearly returning an error when the sysctl write operation receives a GID range that doesn't map to the associated user namespace. In such a situation, the previous value of the sysctl is preserved and that range will be returned in a subsequent read of the sysctl. Signed-off-by:
Tyler Hicks <tyhicks@canonical.com> Signed-off-by:
-
Toke Høiland-Jørgensen authored
[ Upstream commit d5a672ac ] The gen_stats facility will add a header for the toplevel nlattr of type TCA_STATS2 that contains all stats added by qdisc callbacks. A reference to this header is stored in the gnet_dump struct, and when all the per-qdisc callbacks have finished adding their stats, the length of the containing header will be adjusted to the right value. However, on architectures that need padding (i.e., that don't set CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added before the stats, which means that the stored pointer will point to the padding, and so when the header is fixed up, the result is just a very big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS struct, this problem has been mostly invisible, but we exposed it with the netlink attribute-based statistics in CAKE. Fix the issue by fixing up the stored pointer if it points to a padding nlattr. Tested-by:
Pete Heist <pete@heistp.net> Tested-by:
Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk> Signed-off-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
-
Lyude Paul authored
commit 37afe55b upstream. When MST and atomic were introduced to nouveau, another structure that could contain a drm_connector embedded within it was introduced; struct nv50_mstc. This meant that we no longer would be able to simply loop through our connector list and assume that nouveau_connector() would return a proper pointer for each connector, since the assertion that all connectors coming from nouveau have a full nouveau_connector struct became invalid. Unfortunately, none of the actual code that looped through connectors ever got updated, which means that we've been causing invalid memory accesses for quite a while now. An example that was caught by KASAN: [ 201.038698] ================================================================== [ 201.038792] BUG: KASAN: slab-out-of-bounds in nvif_notify_get+0x190/0x1a0 [nouveau] [ 201.038797] Read of size 4 at addr ffff88076738c650 by task kworker/0:3/718 [ 201.038800] [ 201.038822] CPU: 0 PID: 718 Comm: kworker/0:3 Tainted: G O 4.18.0-rc4Lyude-Test+ #1 [ 201.038825] Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET78W (1.51 ) 05/18/2018 [ 201.038882] Workqueue: events nouveau_display_hpd_work [nouveau] [ 201.038887] Call Trace: [ 201.038894] dump_stack+0xa4/0xfd [ 201.038900] print_address_description+0x71/0x239 [ 201.038929] ? nvif_notify_get+0x190/0x1a0 [nouveau] [ 201.038935] kasan_report.cold.6+0x242/0x2fe [ 201.038942] __asan_report_load4_noabort+0x19/0x20 [ 201.038970] nvif_notify_get+0x190/0x1a0 [nouveau] [ 201.038998] ? nvif_notify_put+0x1f0/0x1f0 [nouveau] [ 201.039003] ? kmsg_dump_rewind_nolock+0xe4/0xe4 [ 201.039049] nouveau_display_init.cold.12+0x34/0x39 [nouveau] [ 201.039089] ? nouveau_user_framebuffer_create+0x120/0x120 [nouveau] [ 201.039133] nouveau_display_resume+0x5c0/0x810 [nouveau] [ 201.039173] ? nvkm_client_ioctl+0x20/0x20 [nouveau] [ 201.039215] nouveau_do_resume+0x19f/0x570 [nouveau] [ 201.039256] nouveau_pmops_runtime_resume+0xd8/0x2a0 [nouveau] [ 201.039264] pci_pm_runtime_resume+0x130/0x250 [ 201.039269] ? pci_restore_standard_config+0x70/0x70 [ 201.039275] __rpm_callback+0x1f2/0x5d0 [ 201.039279] ? rpm_resume+0x560/0x18a0 [ 201.039283] ? pci_restore_standard_config+0x70/0x70 [ 201.039287] ? pci_restore_standard_config+0x70/0x70 [ 201.039291] ? pci_restore_standard_config+0x70/0x70 [ 201.039296] rpm_callback+0x175/0x210 [ 201.039300] ? pci_restore_standard_config+0x70/0x70 [ 201.039305] rpm_resume+0xcc3/0x18a0 [ 201.039312] ? rpm_callback+0x210/0x210 [ 201.039317] ? __pm_runtime_resume+0x9e/0x100 [ 201.039322] ? kasan_check_write+0x14/0x20 [ 201.039326] ? do_raw_spin_lock+0xc2/0x1c0 [ 201.039333] __pm_runtime_resume+0xac/0x100 [ 201.039374] nouveau_display_hpd_work+0x67/0x1f0 [nouveau] [ 201.039380] process_one_work+0x7a0/0x14d0 [ 201.039388] ? cancel_delayed_work_sync+0x20/0x20 [ 201.039392] ? lock_acquire+0x113/0x310 [ 201.039398] ? kasan_check_write+0x14/0x20 [ 201.039402] ? do_raw_spin_lock+0xc2/0x1c0 [ 201.039409] worker_thread+0x86/0xb50 [ 201.039418] kthread+0x2e9/0x3a0 [ 201.039422] ? process_one_work+0x14d0/0x14d0 [ 201.039426] ? kthread_create_worker_on_cpu+0xc0/0xc0 [ 201.039431] ret_from_fork+0x3a/0x50 [ 201.039441] [ 201.039444] Allocated by task 79: [ 201.039449] save_stack+0x43/0xd0 [ 201.039452] kasan_kmalloc+0xc4/0xe0 [ 201.039456] kmem_cache_alloc_trace+0x10a/0x260 [ 201.039494] nv50_mstm_add_connector+0x9a/0x340 [nouveau] [ 201.039504] drm_dp_add_port+0xff5/0x1fc0 [drm_kms_helper] [ 201.039511] drm_dp_send_link_address+0x4a7/0x740 [drm_kms_helper] [ 201.039518] drm_dp_check_and_send_link_address+0x1a7/0x210 [drm_kms_helper] [ 201.039525] drm_dp_mst_link_probe_work+0x71/0xb0 [drm_kms_helper] [ 201.039529] process_one_work+0x7a0/0x14d0 [ 201.039533] worker_thread+0x86/0xb50 [ 201.039537] kthread+0x2e9/0x3a0 [ 201.039541] ret_from_fork+0x3a/0x50 [ 201.039543] [ 201.039546] Freed by task 0: [ 201.039549] (stack is not available) [ 201.039551] [ 201.039555] The buggy address belongs to the object at ffff88076738c1a8 which belongs to the cache kmalloc-2048 of size 2048 [ 201.039559] The buggy address is located 1192 bytes inside of 2048-byte region [ffff88076738c1a8, ffff88076738c9a8) [ 201.039563] The buggy address belongs to the page: [ 201.039567] page:ffffea001d9ce200 count:1 mapcount:0 mapping:ffff88084000d0c0 index:0x0 compound_mapcount: 0 [ 201.039573] flags: 0x8000000000008100(slab|head) [ 201.039578] raw: 8000000000008100 ffffea001da3be08 ffffea001da25a08 ffff88084000d0c0 [ 201.039582] raw: 0000000000000000 00000000000d000d 00000001ffffffff 0000000000000000 [ 201.039585] page dumped because: kasan: bad access detected [ 201.039588] [ 201.039591] Memory state around the buggy address: [ 201.039594] ffff88076738c500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 201.039598] ffff88076738c580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 201.039601] >ffff88076738c600: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc [ 201.039604] ^ [ 201.039607] ffff88076738c680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 201.039611] ffff88076738c700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 201.039613] ================================================================== Signed-off-by:
Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Cc: Karol Herbst <karolherbst@gmail.com> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Lyude Paul authored
commit 22b76bbe upstream. Every codepath in nouveau that loops through the connector list currently does so using the old method, which is prone to race conditions from MST connectors being created and destroyed. This has been causing a multitude of problems, including memory corruption from trying to access connectors that have already been freed! Signed-off-by:
-
Ville Syrjälä authored
commit 96a85cc5 upstream. Just like with PIPESTAT, the edge triggered IIR on i965/g4x also causes problems for hotplug interrupts. To make sure we don't get the IIR port interrupt bit stuck low with the ISR bit high we must force an edge in ISR. Unfortunately we can't borrow the PIPESTAT trick and toggle the enable bits in PORT_HOTPLUG_EN as that act itself generates hotplug interrupts. Instead we just have to loop until we've cleared PORT_HOTPLUG_STAT, or we just give up and WARN. v2: Don't frob with PORT_HOTPLUG_EN Cc: stable@vger.kernel.org Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180614175625.1615-1-ville.syrjala@linux.intel.comReviewed-by:
Imre Deak <imre.deak@intel.com> (cherry picked from commit 0ba7c51a) Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
Isaac J. Manjarres authored
commit 9fb8d5dc upstream. When cpu_stop_queue_two_works() begins to wake the stopper threads, it does so without preemption disabled, which leads to the following race condition: The source CPU calls cpu_stop_queue_two_works(), with cpu1 as the source CPU, and cpu2 as the destination CPU. When adding the stopper threads to the wake queue used in this function, the source CPU stopper thread is added first, and the destination CPU stopper thread is added last. When wake_up_q() is invoked to wake the stopper threads, the threads are woken up in the order that they are queued in, so the source CPU's stopper thread is woken up first, and it preempts the thread running on the source CPU. The stopper thread will then execute on the source CPU, disable preemption, and begin executing multi_cpu_stop(), and wait for an ack from the destination CPU's stopper thread, with preemption still disabled. Since the worker thread that woke up the stopper thread on the source CPU is affine to the source CPU, and preemption is disabled on the source CPU, that thread will never run to dequeue the destination CPU's stopper thread from the wake queue, and thus, the destination CPU's stopper thread will never run, causing the source CPU's stopper thread to wait forever, and stall. Disable preemption when waking the stopper threads in cpu_stop_queue_two_works(). Fixes: 0b26351b ("stop_machine, sched: Fix migrate_swap() vs. active_balance() deadlock") Co-Developed-by:
Prasad Sodagudi <psodagud@codeaurora.org> Signed-off-by:
Pavankumar Kondeti <pkondeti@codeaurora.org> Signed-off-by:
Isaac J. Manjarres <isaacm@codeaurora.org> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: peterz@infradead.org Cc: matt@codeblueprint.co.uk Cc: bigeasy@linutronix.de Cc: gregkh@linuxfoundation.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/1530655334-4601-1-git-send-email-isaacm@codeaurora.orgSigned-off-by:
-
Alexey Kardashevskiy authored
commit 1463edca upstream. The size is always equal to 1 page so let's use this. Later on this will be used for other checks which use page shifts to check the granularity of access. This should cause no behavioral change. Cc: stable@vger.kernel.org # v4.12+ Reviewed-by:
David Gibson <david@gibson.dropbear.id.au> Acked-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by:
-
Gustavo A. R. Silva authored
commit 0e714d27 upstream. info.index can be indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: drivers/vfio/pci/vfio_pci.c:734 vfio_pci_ioctl() warn: potential spectre issue 'vdev->region' Fix this by sanitizing info.index before indirectly using it to index vdev->region Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2 Cc: stable@vger.kernel.org Signed-off-by:
-
Rafael J. Wysocki authored
commit 95d6c085 upstream. Currently, intel_pstate doesn't register if _PSS is not present on HP Proliant systems, because it expects the firmware to take over CPU performance scaling in that case. However, if ACPI PCCH is present, the firmware expects the kernel to use it for CPU performance scaling and the pcc-cpufreq driver is loaded for that. Unfortunately, the firmware interface used by that driver is not scalable for fundamental reasons, so pcc-cpufreq is way suboptimal on systems with more than just a few CPUs. In fact, it is better to avoid using it at all. For this reason, modify intel_pstate to look for ACPI PCCH if _PSS is not present and register if it is there. Also prevent the pcc-cpufreq driver from trying to initialize itself if intel_pstate has been registered already. Fixes: fbbcdc07 (intel_pstate: skip the driver if ACPI has power mgmt option) Reported-by:
Andreas Herrmann <aherrmann@suse.com> Reviewed-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Tested-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Hugh Dickins authored
commit e1f1b157 upstream. __split_huge_pmd_locked() must check if the cleared huge pmd was dirty, and propagate that to PageDirty: otherwise, data may be lost when a huge tmpfs page is modified then split then reclaimed. How has this taken so long to be noticed? Because there was no problem when the huge page is written by a write system call (shmem_write_end() calls set_page_dirty()), nor when the page is allocated for a write fault (fault_dirty_shared_page() calls set_page_dirty()); but when allocated for a read fault (which MAP_POPULATE simulates), no set_page_dirty(). Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1807111741430.1106@eggly.anvils Fixes: d21b9e57 ("thp: handle file pages in split_huge_pmd()") Signed-off-by:
Hugh Dickins <hughd@google.com> Reported-by:
Ashwin Chaugule <ashwinch@google.com> Reviewed-by:
Yang Shi <yang.shi@linux.alibaba.com> Reviewed-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Jing Xia authored
commit 9f15bde6 upstream. It was reported that a kernel crash happened in mem_cgroup_iter(), which can be triggered if the legacy cgroup-v1 non-hierarchical mode is used. Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b8f ...... Call trace: mem_cgroup_iter+0x2e0/0x6d4 shrink_zone+0x8c/0x324 balance_pgdat+0x450/0x640 kswapd+0x130/0x4b8 kthread+0xe8/0xfc ret_from_fork+0x10/0x20 mem_cgroup_iter(): ...... if (css_tryget(css)) <-- crash here break; ...... The crashing reason is that mem_cgroup_iter() uses the memcg object whose pointer is stored in iter->position, which has been freed before and filled with POISON_FREE(0x6b). And the root cause of the use-after-free issue is that invalidate_reclaim_iterators() fails to reset the value of iter->position to NULL when the css of the memcg is released in non- hierarchical mode. Link: http://lkml.kernel.org/r/1531994807-25639-1-git-send-email-jing.xia@unisoc.com Fixes: 6df38689 ("mm: memcontrol: fix possible memcg leak due to interrupted reclaim") Signed-off-by:
Jing Xia <jing.xia.mail@gmail.com> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: <chunyan.zhang@unisoc.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Vineet Gupta authored
commit 93312b6d upstream. mprotect(EXEC) was failing for stack mappings as default vm flags was missing MAYEXEC. This was triggered by glibc test suite nptl/tst-execstack testcase What is surprising is that despite running LTP for years on, we didn't catch this issue as it lacks a directed test case. gcc dejagnu tests with nested functions also requiring exec stack work fine though because they rely on the GNU_STACK segment spit out by compiler and handled in kernel elf loader. This glibc case is different as the stack is non exec to begin with and a dlopen of shared lib with GNU_STACK segment triggers the exec stack proceedings using a mprotect(PROT_EXEC) which was broken. CC: stable@vger.kernel.org Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Alexey Brodkin authored
commit 64234961 upstream. We used to have pre-set CONFIG_INITRAMFS_SOURCE with local path to intramfs in ARC defconfigs. This was quite convenient for in-house development but not that convenient for newcomers who obviusly don't have folders like "arc_initramfs" next to the Linux source tree. Which leads to quite surprising failure of defconfig building: ------------------------------->8----------------------------- ../scripts/gen_initramfs_list.sh: Cannot open '../../arc_initramfs_hs/' ../usr/Makefile:57: recipe for target 'usr/initramfs_data.cpio.gz' failed make[2]: *** [usr/initramfs_data.cpio.gz] Error 1 ------------------------------->8----------------------------- So now when more and more people start to deal with our defconfigs let's make their life easier with removal of CONFIG_INITRAMFS_SOURCE. Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Alexey Brodkin authored
commit 6e376114 upstream. swap was broken on ARC due to silly copy-paste issue. We encode offset from swapcache page in __swp_entry() as (off << 13) but were not decoding back in __swp_offset() as (off >> 13) - it was still (off << 13). This finally fixes swap usage on ARC. | # mkswap /dev/sda2 | | # swapon -a -e /dev/sda2 | Adding 500728k swap on /dev/sda2. Priority:-2 extents:1 across:500728k | | # free | total used free shared buffers cached | Mem: 765104 13456 751648 4736 8 4736 | -/+ buffers/cache: 8712 756392 | Swap: 500728 0 500728 Cc: stable@vger.kernel.org Signed-off-by:
-
Vineet Gupta authored
commit af1fc5ba upstream. This manifsted as strace segfaulting on HSDK because gcc was targetting the accumulator registers as GPRs, which kernek was not saving/restoring by default. Cc: stable@vger.kernel.org #4.14+ Signed-off-by:
-
Po-Hsu Lin authored
commit 9a6249d2 upstream. Audio mute led does not work on HP ProBook 455 G5, this can be fixed by using CXT_FIXUP_MUTE_LED_GPIO to support it. BugLink: https://bugs.launchpad.net/bugs/1781763 Reported-by: James Buren Signed-off-by:
Po-Hsu Lin <po-hsu.lin@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
YOKOTA Hiroshi authored
commit 0fca97a2 upstream. This adds some required quirk when uses headset or headphone on Panasonic CF-SZ6. Signed-off-by:
YOKOTA Hiroshi <yokota.hgml@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit 39675f7a upstream. The SNDRV_RAWMIDI_IOCTL_PARAMS ioctl may resize the buffers and the current code is racy. For example, the sequencer client may write to buffer while it being resized. As a simple workaround, let's switch to the resized buffer inside the stream runtime lock. Reported-by: syzbot+52f83f0ea8df16932f7f@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Signed-off-by:
-
OGAWA Hirofumi authored
commit 35033ab9 upstream. In parse_options(), if match_strdup() failed, parse_options() leaves opts->iocharset in unexpected state (i.e. still pointing the freed string). And this can be the cause of double free. To fix, this initialize opts->iocharset always when freeing. Link: http://lkml.kernel.org/r/8736wp9dzc.fsf@mail.parknet.co.jpSigned-off-by:
OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Reported-by: syzbot+90b8e10515ae88228a92@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Signed-off-by:
-
Dewet Thibaut authored
commit fbdb328c upstream. commit b3b7c479 ("x86/MCE: Serialize sysfs changes") introduced a min interval limitation when setting the check interval for polled MCEs. However, the logic is that 0 disables polling for corrected MCEs, see Documentation/x86/x86_64/machinecheck. The limitation prevents disabling. Remove this limitation and allow the value 0 to disable polling again. Fixes: b3b7c479 ("x86/MCE: Serialize sysfs changes") Signed-off-by:
Dewet Thibaut <thibaut.dewet@nokia.com> Signed-off-by:
Alexander Sverdlin <alexander.sverdlin@nokia.com> [ Massage commit message. ] Signed-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
