Due to DCBX configuration change if the VSI needs to use more than 1 TC;
it needs to disable the XPS maps that were set when operating in 1 TC mode.
Without disabling XPS the netdev layer will select queues based on those
settings and not use the TC queue mapping to make the queue selection.

This patch allows the driver to enable/disable the XPS based on the number
of TCs being enabled for the given VSI.

Change-ID: Idc4dec47a672d2a509f6d7fe11ed1ee65b4f0e08
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When PFC is enabled we should not proceed with setting the link flow control
parameters.  Also, always report the link flow Tx/Rx settings as off when
PFC is enabled.

Change-ID: Ib09ec58afdf0b2e587ac9d8851a5c80ad58206c4
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

FCoE VSI Tx queue disable times out when reconfiguring as a result of
DCB TC configuration change event.

The hardware allows us to skip disabling and enabling of Tx queues for
VSIs with single TC enabled. As FCoE VSI is configured to have only
single TC we skip it from disable/enable flow.

Change-ID: Ia73ff3df8785ba2aa3db91e6f2c9005e61ebaec2
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When DCB TC configuration changes the firmware suspends the port's Tx.
Now, as DCB TCs may have changed the PF driver tries to reconfigure the
TC configuration of the VSIs it manages. As part of this process it disables
the VSI queues but the Tx queue disable will not complete as the port's
Tx has been suspended. So, waiting for Tx queues to go to disable state
in this flow may lead to detection of Tx queue disable timeout errors.

Hence, this patch adds a new PF state so that if a port's Tx is in
suspended state the Tx queue disable flow would just put the request for
the queue to be disabled and return without waiting for the queue to be
actually disabled.
Once the VSI(s) TC reconfiguration has been done and driver has called
firmware AQC "Resume PF Traffic" the driver checks the Tx queues requested
to be disabled are actually disabled before re-enabling them again.

Change-ID: If3e03ce4813a4e342dbd5a1eb1d2861e952b7544
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the port TC configuration changes as a result of DCBx the driver
modifies the enabled TCs for the VEBs it manages. But, in the process
it did not update the enabled_tc value that it caches on a per VEB basis.

So, when the next reconfiguration event occurs where the number of TC
value is same as the value cached in enabled_tc for a given VEB; driver
does not modify it's TC configuration by calling appropriate AQ command
believing it is running with the same configuration as requested.
Now, as the VEB is not actually enabled for the TCs that are there any
TC configuration command for VSI attached to that VEB with TCs that are
not enabled for the VEB fails.

This patch fixes this issue.

Change-ID: Ife5694469b05494228e0d850429ea1734738cf29
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a check whether LLDP Agent's default AdminStatus is
enabled or disabled on a given port. If it is disabled then it sets
the DCBX status to disabled as well; and would not query firmware for
any DCBX configuration data.

Change-ID: I73c0b9f0adbf4cae177d14914b20a48c9a8f50fd
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allows i40e driver to query and use DCB configuration from
firmware when firmware DCBX agent is in CEE mode.

Change-ID: I30f92a67eb890f0f024f35339696e6e83d49a274
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When there are DCB configuration changes based on DCBX the firmware suspends
the port's Tx and generates an event to the PF. The PF is then responsible
to reconfigure the PF VSIs and switching topology as per the updated DCB
configuration and then resume the port's Tx by calling the "Resume Port Tx"
AQ command.

This patch adds this call to the flow that handles DCB re-configuration in
the PF.

Change-ID: I5b860ad48abfbf379b003143c4d3453e2ed5cc1c
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Bumping minor version as this will be the second SW release and it
should be 1.

Change-ID: If0bd102095d2f059ae0c9b7f4ad625535ffbbdee
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

VF interrupt processing takes a looooong time, and it's possible that we
could lose a VFLR event if it happens while we're processing a VFLR on
another VF. This would leave the VF in a semi-permanent reset state,
which would not be cleared until yet another VF experiences a VFLR.

To correct this situation, we enable the VFLR interrupt cause before we
begin processing any pending resets. This means that any VFLR that
occurs during reset processing will generate another interrupt and this
routine will get called again.

This change may cause a spurious interrupt when multiple VFLRs occur
very close together in time. If this happens, then this routine will be
called again and it will detect no outstanding VFLR events and do
nothing. No harm, no foul.

Change-ID: Id0451f3e6e73a2cf6db1668296c71e129b59dc19
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Only warn once that PTP is not supported when linked at 100Mbit.

Yes, using a static this way means that this once-only message is not
port specific, but once only for the life of the driver, regardless of
the number of ports.  That should be plenty.

Change-ID: Ie6476530056df408452e195ef06afd4f57caa4b2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Eric Dumazet says:

====================
net: provide common RSS key infrastructure

RSS (Receive Side Scaling) uses a 40 bytes key to provide hash for incoming
packets to select appropriate incoming queue on NIC.

Hash algo (Toeplitz) is also well known and documented by Microsoft
(search for "Verifying the RSS Hash Calculation")

Problem is that some drivers use a well known key.
It makes very easy for attackers to target one particular RX queue,
knowing that number of RX queues is a power of two, or at least some
small number.

Other drivers use a random value per port, making difficult
tuning on bonding setups.

Lets add a common infrastructure, so that host gets an unique
RSS key, and drivers do not have to worry about this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.

Also provide ethtool -x support to fetch RSS key
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Rename rss_hkey local variable to rss_key to have consistent name among
drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lendacky, Thomas <Thomas.Lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RSS (Receive Side Scaling) typically uses Toeplitz hash and a 40 or 52 bytes
RSS key.

Some drivers use a constant (and well known key), some drivers use a random
key per port, making bonding setups hard to tune. Well known keys increase
attack surface, considering that number of queues is usually a power of two.

This patch provides infrastructure to help drivers doing the right thing.

netdev_rss_key_fill() should be used by drivers to initialize their RSS key,
even if they provide ethtool -X support to let user redefine the key later.

A new /proc/sys/net/core/netdev_rss_key file can be used to get the host
RSS key even for drivers not providing ethtool -x support, in case some
applications want to precisely setup flows to match some RX queues.

Tested:

myhost:~# cat /proc/sys/net/core/netdev_rss_key
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41:36:40:74:b6:15:ca:27:44:aa:b3:4d:72

myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
    0:      0     1     2     3     4     5     6     7
RSS hash key:
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Add temperature reading and registers dump to mv88e6171

These patches centralize the temperature sensor reading code, and then
make use of it with the mv88e6171 which has a compatible
sensor. Additionally, support is added for reading the mv88e6171 via
ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The infrastructure can now report switch registers to ethtool.
Add support for it to the mv88e6171 driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This chip also has a temperature sensor which can be read using the
common code. In order to use it, add the needed mutex protection for
accessing registers via the shared code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method to read the temperature used in the mve6123_61_65 driver
can also be used for other chips. Move the code into the shared code
base of mv88e6xxx.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

kcalloc manages count*sizeof overflow.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

kmalloc_array manages count*sizeof overflow.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no reason to limit the amount of possible links to a
neighboring node to 2. If we have more then two bearers we can also
establish more links.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Reviewed-By: Jon Maloy <jon.maloy@ericsson.com>
cc: Ying Xue <ying.xue@windriver.com>
cc: Erik Hugne <erik.hugne@ericsson.com>
cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit e5a2c899.

	Commit e5a2c899 introduced an alternative_call, arch_fast_hash2,
that selects between __jhash2 and __intel_crc4_2_hash based on the
X86_FEATURE_XMM4_2.

	Unfortunately, the alternative_call system does not appear to be
suitable for use with C functions, as register usage is not handled
properly for the called functions.  The __jhash2 function in particular
clobbers registers that are not preserved when called via
alternative_call, resulting in a panic for direct callers of
arch_fast_hash2 on older CPUs lacking sse4_2.  It is possible that
__intel_crc4_2_hash works merely by chance because it uses fewer
registers.

	This commit was suggested as the source of the problem by Jesse
Gross <jesse@nicira.com>.
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dependency on INET to fix following build error. I have also
fixed MPLS dependency.

ERROR: "ip_route_output_flow" [net/openvswitch/openvswitch.ko]
undefined!
make[1]: *** [__modpost] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/chelsio/cxgb4vf/sge.c
	drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c

sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.

ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull virtio bugfix from Michael S Tsirkin:
 "This fixes a crash in virtio console multi-channel mode that got
  introduced in -rc1"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_console: move early VQ enablement

Pull networking fixes from David Miller:

 1) sunhme driver lacks DMA mapping error checks, based upon a report by
    Meelis Roos.

 2) Fix memory leak in mvpp2 driver, from Sudip Mukherjee.

 3) DMA memory allocation sizes are wrong in systemport ethernet driver,
    fix from Florian Fainelli.

 4) Fix use after free in mac80211 defragmentation code, from Johannes
    Berg.

 5) Some networking uapi headers missing from Kbuild file, from Stephen
    Hemminger.

 6) TUN driver gets csum_start offset wrong when VLAN accel is enabled,
    and macvtap has a similar bug, from Herbert Xu.

 7) Adjust several tunneling drivers to set dev->iflink after registry,
    because registry sets that to -1 overwriting whatever we did.  From
    Steffen Klassert.

 8) Geneve forgets to set inner tunneling type, causing GSO segmentation
    to fail on some NICs.  From Jesse Gross.

 9) Fix several locking bugs in stmmac driver, from Fabrice Gasnier and
    Giuseppe CAVALLARO.

10) Fix spurious timeouts with NewReno on low traffic connections, from
    Marcelo Leitner.

11) Fix descriptor updates in enic driver, from Govindarajulu
    Varadarajan.

12) PPP calls bpf_prog_create() with locks held, which isn't kosher.
    Fix from Takashi Iwai.

13) Fix NULL deref in SCTP with malformed INIT packets, from Daniel
    Borkmann.

14) psock_fanout selftest accesses past the end of the mmap ring, fix
    from Shuah Khan.

15) Fix PTP timestamping for VLAN packets, from Richard Cochran.

16) netlink_unbind() calls in netlink pass wrong initial argument, from
    Hiroaki SHIMODA.

17) vxlan socket reuse accidently reuses a socket when the address
    family is different, so we have to explicitly check this, from
    Marcelo Lietner.

18) Fix missing include in nft_reject_bridge.c breaking the build on ppc
    and other architectures, from Guenter Roeck.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
  vxlan: Do not reuse sockets for a different address family
  smsc911x: power-up phydev before doing a software reset.
  lib: rhashtable - Remove weird non-ASCII characters from comments
  net/smsc911x: Fix delays in the PHY enable/disable routines
  net/smsc911x: Fix rare soft reset timeout issue due to PHY power-down mode
  netlink: Properly unbind in error conditions.
  net: ptp: fix time stamp matching logic for VLAN packets.
  cxgb4 : dcb open-lldp interop fixes
  selftests/net: psock_fanout seg faults in sock_fanout_read_ring()
  net: bcmgenet: apply MII configuration in bcmgenet_open()
  net: bcmgenet: connect and disconnect from the PHY state machine
  net: qualcomm: Fix dependency
  ixgbe: phy: fix uninitialized status in ixgbe_setup_phy_link_tnx
  net: phy: Correctly handle MII ioctl which changes autonegotiation.
  ipv6: fix IPV6_PKTINFO with v4 mapped
  net: sctp: fix memory leak in auth key management
  net: sctp: fix NULL pointer dereference in af->from_addr_param on malformed packet
  net: ppp: Don't call bpf_prog_create() in ppp_lock
  net/mlx4_en: Advertize encapsulation offloads features only when VXLAN tunnel is set
  cxgb4 : Fix bug in DCB app deletion
  ...

Merge misc fixes from Andrew Morton:
 "15 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  MAINTAINERS: add IIO include files
  kernel/panic.c: update comments for print_tainted
  mem-hotplug: reset node present pages when hot-adding a new pgdat
  mem-hotplug: reset node managed pages when hot-adding a new pgdat
  mm/debug-pagealloc: correct freepage accounting and order resetting
  fanotify: fix notification of groups with inode & mount marks
  mm, compaction: prevent infinite loop in compact_zone
  mm: alloc_contig_range: demote pages busy message from warn to info
  mm/slab: fix unalignment problem on Malta with EVA due to slab merge
  mm/page_alloc: restrict max order of merging on isolated pageblock
  mm/page_alloc: move freepage counting logic to __free_one_page()
  mm/page_alloc: add freepage on isolate pageblock to correct buddy list
  mm/page_alloc: fix incorrect isolation behavior by rechecking migratetype
  mm/compaction: skip the range until proper target pageblock is met
  zram: avoid kunmap_atomic() of a NULL pointer