commit 9c41f4ee upstream.

A vmalloc fault needs to sync up PGD/PTE entry from init_mm to current
task's "active_mm".  ARC vmalloc fault handler however was using mm.

A vmalloc fault for non user task context (actually pre-userland, from
init thread's open for /dev/console) caused the handler to deref NULL mm
(for mm->pgd)

The reasons it worked so far is amazing:

1. By default (!SMP), vmalloc fault handler uses a cached value of PGD.
   In SMP that MMU register is repurposed hence need for mm pointer deref.

2. In pre-3.12 SMP kernel, the problem triggering vmalloc didn't exist in
   pre-userland code path - it was introduced with commit 20bafb3d
   "n_tty: Move buffers into n_tty_data"
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f6537f2f upstream.

This patch uses CONFIG_PAGE_OFFSET to filter symbols which
are not in kernel address space because these symbols are
generally for generating code purpose and can't be run at
kernel mode, so we needn't keep them in /proc/kallsyms.

For example, on ARM there are some symbols which may be
linked in relocatable code section, then perf can't parse
symbols any more from /proc/kallsyms, this patch fixes the
problem (introduced b9b32bf7)

Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 54e181e0 upstream.

Since the beginning of the parisc-linux port, sometimes 64bit SMP kernels were
not able to bring up other CPUs than the monarch CPU and instead crashed the
kernel.  The reason was unclear, esp. since it involved various machines (e.g.
J5600, J6750 and SuperDome). Testing showed, that those crashes didn't happened
when less than 4GB were installed, or if a 32bit Linux kernel was booted.

In the end, the fix for those SMP problems is trivial:
During the early phase of the initialization of the CPUs, including the monarch
CPU, the PDC_PSW firmware function to enable WIDE (=64bit) mode is called.
It's documented that this firmware function may clobber various registers, and
one one of those possibly clobbered registers is %cr30 which holds the task
thread info pointer.

Now, if %cr30 would always have been clobbered, then this bug would have been
detected much earlier. But lots of testing finally showed, that - at least for
%cr30 - on some machines only the upper 32bits of the 64bit register suddenly
turned zero after the firmware call.

So, after finding the root cause, the explanation for the various crashes
became clear:
- On 32bit SMP Linux kernels all upper 32bit were zero, so we didn't faced this
  problem.
- Monarch CPUs in 64bit mode always booted sucessfully, because the inital task
  thread info pointer was below 4GB.
- Secondary CPUs booted sucessfully on machines with less than 4GB RAM because
  the upper 32bit were zero anyay.
- Secondary CPus failed to boot if we had more than 4GB RAM and the task thread
  info pointer was located above the 4GB boundary.

Finally, the patch to fix this problem is trivial by saving the %cr30 register
before the firmware call and restoring it afterwards.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 97b94106 upstream.

Marc Kleine-Budde pointed out, that commit 77cc982f "clocksource: use
clockevents_config_and_register() where possible" caused a regression
for some of the converted subarchs.

The reason is, that the clockevents core code converts the minimal
hardware tick delta to a nanosecond value for core internal
usage. This conversion is affected by integer math rounding loss, so
the backwards conversion to hardware ticks will likely result in a
value which is less than the configured hardware limitation. The
affected subarchs used their own workaround (SIGH!) which got lost in
the conversion.

The solution for the issue at hand is simple: adding evt->mult - 1 to
the shifted value before the integer divison in the core conversion
function takes care of it. But this only works for the case where for
the scaled math mult/shift pair "mult <= 1 << shift" is true. For the
case where "mult > 1 << shift" we can apply the rounding add only for
the minimum delta value to make sure that the backward conversion is
not less than the given hardware limit. For the upper bound we need to
omit the rounding add, because the backwards conversion is always
larger than the original latch value. That would violate the upper
bound of the hardware device.

Though looking closer at the details of that function reveals another
bogosity: The upper bounds check is broken as well. Checking for a
resulting "clc" value greater than KTIME_MAX after the conversion is
pointless. The conversion does:

      u64 clc = (latch << evt->shift) / evt->mult;

So there is no sanity check for (latch << evt->shift) exceeding the
64bit boundary. The latch argument is "unsigned long", so on a 64bit
arch the handed in argument could easily lead to an unnoticed shift
overflow. With the above rounding fix applied the calculation before
the divison is:

       u64 clc = (latch << evt->shift) + evt->mult - 1;

So we need to make sure, that neither the shift nor the rounding add
is overflowing the u64 boundary.

[ukl: move assignment to rnd after eventually changing mult, fix build
 issue and correct comment with the right math]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: nicolas.ferre@atmel.com
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: john.stultz@linaro.org
Cc: kernel@pengutronix.de
Cc: Ronald Wahl <ronald.wahl@raritan.com>
Cc: LAK <linux-arm-kernel@lists.infradead.org>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Link: http://lkml.kernel.org/r/1380052223-24139-1-git-send-email-u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 60a01f55 upstream.

This patch addresses a long-standing bug where the get_user_pages_fast()
write parameter used for setting the underlying page table entry permission
bits was incorrectly set to write=1 for data_direction=DMA_TO_DEVICE, and
passed into get_user_pages_fast() via vhost_scsi_map_iov_to_sgl().

However, this parameter is intended to signal WRITEs to pinned userspace
PTEs for the virtio-scsi DMA_FROM_DEVICE -> READ payload case, and *not*
for the virtio-scsi DMA_TO_DEVICE -> WRITE payload case.

This bug would manifest itself as random process segmentation faults on
KVM host after repeated vhost starts + stops and/or with lots of vhost
endpoints + LUNs.

Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 58932e96 upstream.

In case of error, the function scsi_host_lookup() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 61e4947c upstream.

Since:
        commit 7ceb17e8
        md: Allow devices to be re-added to a read-only array.

spares are activated on a read-only array. In case of raid1 and raid10
personalities it causes that not-in-sync devices are marked in-sync
without checking if recovery has been finished.

If a read-only array is degraded and one of its devices is not in-sync
(because the array has been only partially recovered) recovery will be skipped.

This patch adds checking if recovery has been finished before marking a device
in-sync for raid1 and raid10 personalities. In case of raid5 personality
such condition is already present (at raid5.c:6029).

Bug was introduced in 3.10 and causes data corruption.
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 905b0297 upstream.

When operate harddisk and hit errors, md_set_badblocks is called after
scsi_restart_operations which already disabled the irq. but md_set_badblocks
will call write_sequnlock_irq and enable irq. so softirq can preempt the
current thread and that may cause a deadlock. I think this situation should
use write_sequnlock_irqsave/irqrestore instead.

I met the situation and the call trace is below:
[  638.919974] BUG: spinlock recursion on CPU#0, scsi_eh_13/1010
[  638.921923]  lock: 0xffff8800d4d51fc8, .magic: dead4ead, .owner: scsi_eh_13/1010, .owner_cpu: 0
[  638.923890] CPU: 0 PID: 1010 Comm: scsi_eh_13 Not tainted 3.12.0-rc5+ #37
[  638.925844] Hardware name: To be filled by O.E.M. To be filled by O.E.M./MAHOBAY, BIOS 4.6.5 03/05/2013
[  638.927816]  ffff880037ad4640 ffff880118c03d50 ffffffff8172ff85 0000000000000007
[  638.929829]  ffff8800d4d51fc8 ffff880118c03d70 ffffffff81730030 ffff8800d4d51fc8
[  638.931848]  ffffffff81a72eb0 ffff880118c03d90 ffffffff81730056 ffff8800d4d51fc8
[  638.933884] Call Trace:
[  638.935867]  <IRQ>  [<ffffffff8172ff85>] dump_stack+0x55/0x76
[  638.937878]  [<ffffffff81730030>] spin_dump+0x8a/0x8f
[  638.939861]  [<ffffffff81730056>] spin_bug+0x21/0x26
[  638.941836]  [<ffffffff81336de4>] do_raw_spin_lock+0xa4/0xc0
[  638.943801]  [<ffffffff8173f036>] _raw_spin_lock+0x66/0x80
[  638.945747]  [<ffffffff814a73ed>] ? scsi_device_unbusy+0x9d/0xd0
[  638.947672]  [<ffffffff8173fb1b>] ? _raw_spin_unlock+0x2b/0x50
[  638.949595]  [<ffffffff814a73ed>] scsi_device_unbusy+0x9d/0xd0
[  638.951504]  [<ffffffff8149ec47>] scsi_finish_command+0x37/0xe0
[  638.953388]  [<ffffffff814a75e8>] scsi_softirq_done+0xa8/0x140
[  638.955248]  [<ffffffff8130e32b>] blk_done_softirq+0x7b/0x90
[  638.957116]  [<ffffffff8104fddd>] __do_softirq+0xfd/0x330
[  638.958987]  [<ffffffff810b964f>] ? __lock_release+0x6f/0x100
[  638.960861]  [<ffffffff8174a5cc>] call_softirq+0x1c/0x30
[  638.962724]  [<ffffffff81004c7d>] do_softirq+0x8d/0xc0
[  638.964565]  [<ffffffff8105024e>] irq_exit+0x10e/0x150
[  638.966390]  [<ffffffff8174ad4a>] smp_apic_timer_interrupt+0x4a/0x60
[  638.968223]  [<ffffffff817499af>] apic_timer_interrupt+0x6f/0x80
[  638.970079]  <EOI>  [<ffffffff810b964f>] ? __lock_release+0x6f/0x100
[  638.971899]  [<ffffffff8173fa6a>] ? _raw_spin_unlock_irq+0x3a/0x50
[  638.973691]  [<ffffffff8173fa60>] ? _raw_spin_unlock_irq+0x30/0x50
[  638.975475]  [<ffffffff81562393>] md_set_badblocks+0x1f3/0x4a0
[  638.977243]  [<ffffffff81566e07>] rdev_set_badblocks+0x27/0x80
[  638.978988]  [<ffffffffa00d97bb>] raid5_end_read_request+0x36b/0x4e0 [raid456]
[  638.980723]  [<ffffffff811b5a1d>] bio_endio+0x1d/0x40
[  638.982463]  [<ffffffff81304ff3>] req_bio_endio.isra.65+0x83/0xa0
[  638.984214]  [<ffffffff81306b9f>] blk_update_request+0x7f/0x350
[  638.985967]  [<ffffffff81306ea1>] blk_update_bidi_request+0x31/0x90
[  638.987710]  [<ffffffff813085e0>] __blk_end_bidi_request+0x20/0x50
[  638.989439]  [<ffffffff8130862f>] __blk_end_request_all+0x1f/0x30
[  638.991149]  [<ffffffff81308746>] blk_peek_request+0x106/0x250
[  638.992861]  [<ffffffff814a62a9>] ? scsi_kill_request.isra.32+0xe9/0x130
[  638.994561]  [<ffffffff814a633a>] scsi_request_fn+0x4a/0x3d0
[  638.996251]  [<ffffffff813040a7>] __blk_run_queue+0x37/0x50
[  638.997900]  [<ffffffff813045af>] blk_run_queue+0x2f/0x50
[  638.999553]  [<ffffffff814a5750>] scsi_run_queue+0xe0/0x1c0
[  639.001185]  [<ffffffff814a7721>] scsi_run_host_queues+0x21/0x40
[  639.002798]  [<ffffffff814a2e87>] scsi_restart_operations+0x177/0x200
[  639.004391]  [<ffffffff814a4fe9>] scsi_error_handler+0xc9/0xe0
[  639.005996]  [<ffffffff814a4f20>] ? scsi_unjam_host+0xd0/0xd0
[  639.007600]  [<ffffffff81072f6b>] kthread+0xdb/0xe0
[  639.009205]  [<ffffffff81072e90>] ? flush_kthread_worker+0x170/0x170
[  639.010821]  [<ffffffff81748cac>] ret_from_fork+0x7c/0xb0
[  639.012437]  [<ffffffff81072e90>] ? flush_kthread_worker+0x170/0x170

This bug was introduce in commit  2e8ac303
(the first time rdev_set_badblock was call from interrupt context),
so this patch is appropriate for 3.5 and subsequent kernels.
Signed-off-by: Bian Yu <bianyu@kedacom.com>
Reviewed-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f13e2201 upstream.

libata EH decrements scmd->retries when the command failed for reasons
unrelated to the command itself so that, for example, commands aborted
due to suspend / resume cycle don't get penalized; however,
decrementing scmd->retries isn't enough for ATA passthrough commands.

Without this fix, ATA passthrough commands are not resend to the
drive, and no error is signalled to the caller because:

- allowed retry count is 1
- ata_eh_qc_complete fill the sense data, so result is valid
- sense data is filled with untouched ATA registers.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d47648fc upstream.

SCSI discard will damage discard stripe bio setting, eg, some fields are
changed. If the stripe is reused very soon, we have wrong bios setting. We
remove discard stripe from hash list, so next time the strip will be fully
initialized.

Suitable for backport to 3.7+.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 37c61ff3 upstream.

SCSI layer will add new payload for discard request. If two bios are merged
to one, the second bio has bi_vcnt 1 which is set in raid5. This will confuse
SCSI and cause oops.

Suitable for backport to 3.7+
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3edc8376 upstream.

In 'decrypt_pki_encrypted_session_key' function:

Initializes 'payload' pointer and releases it on exit.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 10c580e4 upstream.

Sujit has found a race condition that would make q->nr_pending
unbalanced, it occurs as Sujit explained:

"
sd_probe_async() ->
	add_disk() ->
		disk_add_event() ->
			schedule(disk_events_workfn)
	sd_revalidate_disk()
	blk_pm_runtime_init()
return;

Let's say the disk_events_workfn() calls sd_check_events() which tries
to send test_unit_ready() and because of sd_revalidate_disk() trying to
send another commands the test_unit_ready() might be re-queued as the
tagged command queuing is disabled.

So the race condition is -

Thread 1 			  |		Thread 2
sd_revalidate_disk()		  |	sd_check_events()
...nr_pending = 0 as q->dev = NULL|	scsi_queue_insert()
blk_runtime_pm_init()		  | 	blk_pm_requeue_request() ->
				  |	nr_pending = -1 since
				  |	q->dev != NULL
"

The problem is, the test_unit_ready request doesn't get counted the
first time it is queued, so the later decrement of q->nr_pending in
blk_pm_requeue_request makes it unbalanced.

Fix this by calling blk_pm_runtime_init before add_disk so that all
requests initiated there will all be counted.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reported-and-tested-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d5a7b406 upstream.

In patch

    0d1862ea can: flexcan: fix flexcan_chip_start() on imx6

the loop in flexcan_chip_start() that iterates over all mailboxes after the
soft reset of the CAN core was removed. This loop put all mailboxes (even the
ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63,
this aborts any pending TX messages.

After a cold boot there is random garbage in the mailboxes, which leads to
spontaneous transmit of CAN frames during first activation. Further if the
interface was disabled with a pending message (usually due to an error
condition on the CAN bus), this message is retransmitted after enabling the
interface again.

This patch fixes the regression by:
1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX
FIFO, 8 is used by TX.
2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that
mailbox is aborted.

Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e3587842 upstream.

The current implemetation of of_match_device() relies that the of_device_id
table in the driver is sorted from most specific to least specific compatible.

Without this patch the mx28 is detected as the less specific p1010. This leads
to a p1010 specific workaround is activated on the mx28, which is not needed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5abbeea5 upstream.

In commit:

    3078cde7 can: at91_can: add dt support

device tree support was added to the at91_can driver. In this commit the
mapping of device to driver data was mixed up. This results in the sam9x5
parameters being used for the sam9263 and the workaround for the broken mailbox
0 on the sam9263 not being activated.

This patch fixes the broken platform_device_id table.

Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 86609986 upstream.

If insert_inode_locked() fails, we shouldn't be calling
unlock_new_inode().
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Tested-by: Michael L. Semon <mlsemon35@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 08a5dd38 upstream.

Add some new PCI IDs to the table for 6000, 6005 and 6235 series.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9473ca6e upstream.

An error in calculating the offset in an skb causes the driver to read
essential device info from the wrong locations. The main effect is that
automatic gain calculations are nonsense.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 453b0c3f upstream.

601216e1 "mwifiex: process RX packets in SDIO IRQ thread directly"
introduced a command timeout issue which can be reproduced easily on
an AM33xx platform using a test application written by Daniel Mack:

https://gist.github.com/zonque/6579314

mwifiex_main_process() is called from both the SDIO handler and
the workqueue. In case an interrupt occurs right after the
int_status check, but before updating the mwifiex_processing flag,
this interrupt gets lost, resulting in a command timeout and
consequently a card reset.

Let main_proc_lock protect both int_status and mwifiex_processing
flag. This fixes the interrupt lost issue.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f478f33a upstream.

Fix kernel warning when using WEXT for configuring ad-hoc mode,
e.g.  "iwconfig wlan0 essid test channel 1"

WARNING: at net/wireless/chan.c:373 cfg80211_chandef_usable+0x50/0x21c [cfg80211]()

The warning is caused by an uninitialized variable center_freq1.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ec30326e upstream.

Otherwise, if queues are full during a scan, tx scheduling does not
resume after switching back to the home channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d86aa4f8 upstream.

If a frame's timestamp is calculated, and the bitrate
calculation goes wrong and returns zero, the system
will attempt to divide by zero and crash. Catch this
case and print the rate information that the driver
reported when this happens.
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0c5b9329 upstream.

When clients are idle for too long, hostapd sends nullfunc frames for
probing. When those are acked by the client, the idle time needs to be
updated.

To make this work (and to avoid unnecessary probing), update sta->last_rx
whenever an ACK was received for a tx packet. Only do this if the flag
IEEE80211_HW_REPORTS_TX_ACK_STATUS is set.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 03bb7f42 upstream.

This allows calls for clients in AP_VLANs (e.g. for 4-addr) to succeed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6329b8d9 upstream.

If an Ad-Hoc node receives packets with the Cell ID or its own MAC
address as source address, it hits a WARN_ON in sta_info_insert_check()
With many packets, this can massively spam the logs. One way that this
can easily happen is through having Cisco APs in the area with rouge AP
detection and countermeasures enabled.
Such Cisco APs will regularly send fake beacons, disassoc and deauth
packets that trigger these warnings.

To fix this issue, drop such spoofed packets early in the rx path.
Reported-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a754055a upstream.

__ieee80211_scan_completed is called from a worker. This
means that the following flow is possible.

 * driver calls ieee80211_scan_completed
 * mac80211 cancels the scan (that is already complete)
 * __ieee80211_scan_completed runs

When scan_work will finally run, it will see that the scan
hasn't been aborted and might even trigger another scan on
another band. This leads to a situation where cfg80211's
scan is not done and no further scan can be issued.

Fix this by setting a new flag when a HW scan is being
cancelled so that no other scan will be triggered.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ea84753c upstream.

Both Anjana and Eunki reported a stall in the while_each_thread loop
in cgroup_attach_task().

It's because, when we attach a single thread to a cgroup, if the cgroup
is exiting or is already in that cgroup, we won't break the loop.

If the task is already in the cgroup, the bug can lead to another thread
being attached to the cgroup unexpectedly:

  # echo 5207 > tasks
  # cat tasks
  5207
  # echo 5207 > tasks
  # cat tasks
  5207
  5215

What's worse, if the task to be attached isn't the leader of the thread
group, we might never exit the loop, hence cpu stall. Thanks for Oleg's
analysis.

This bug was introduced by commit 081aa458
("cgroup: consolidate cgroup_attach_task() and cgroup_attach_proc()")

[ lizf: - fixed the first continue, pointed out by Oleg,
        - rewrote changelog. ]
Reported-by: Eunki Kim <eunki_kim@samsung.com>
Reported-by: Anjana V Kumar <anjanavk12@gmail.com>
Signed-off-by: Anjana V Kumar <anjanavk12@gmail.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d4eddd42 upstream.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 52e0a509 upstream.

If the system is suspended while max_perf_pct is less than 100 percent
or no_turbo set policy->{min,max} will be set incorrectly with scaled
values which turn the scaled values into hard limits.

References: https://bugzilla.kernel.org/show_bug.cgi?id=61241Reported-by: Patrick Bartels <petzicus@googlemail.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dd3c9c4b upstream.

The UV3 hub revision ID is different than expected.  The first
revision was supposed to start at 1 but instead will start at 0.
Signed-off-by: Russ Anderson <rja@sgi.com>
Link: http://lkml.kernel.org/r/20131014161733.GA6274@sgi.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e1466ad5 upstream.

Custom VID/PID for Z3X Box device, popular tool for cellphone flashing.
Signed-off-by: Alexey E. Kramarenko <alexeyk13@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 614ced91 upstream.

The device descriptors are messed up after remote wakeup
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4294bca7 upstream.

The device is not responsive when resumed, unless it is reset.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d544db29 upstream.

Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceSubClass value.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 32c37fc3 upstream.

Some USB drive enclosures do not correctly report an
overflow condition if they hold a drive with a capacity
over 2TB and are confronted with a READ_CAPACITY_10.
They answer with their capacity modulo 2TB.
The generic layer cannot cope with that. It must be told
to use READ_CAPACITY_16 from the beginning.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fd8573f5 upstream.

Interface 6 of this device speaks QMI as per tests done by us.
Credits go to Antonella for providing the hardware.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f4c19b8e upstream.

This patch adds the device id for the Inovia SEW858 device to the option driver.
Reported-by: Pavel Parkhomenko <ra85551@gmail.com>
Tested-by: Pavel Parkhomenko <ra85551@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c9d09dc7 upstream.

Without this change, the USB cable for Freestyle Option and compatible
glucometers will not be detected by the driver.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>