- 09 Feb, 2017 11 commits
-
-
Quinn Tran authored
Current code blindly does State Change Registration when the link is up. Move SCR behind fabric scan, so that arbitrated loop scan would not get erroneous error message. Some of the other improvements are as follows - Add session deletion for TPRLO and send acknowledgment for TPRLO. - Enable FW option to move ABTS, RIDA & PUREX from RSPQ to ATIOQ. - Save NPort ID early in link init. - Move ABTS & RIDA to ATIOQ helps in keeping command ordering and link up sequence ordering. - Save Nport ID and update VP map so that SCSI CMD/ATIO won't be dropped. - fcport alloc does the initializes memory to zero. Remove memset to zero since It might corrupt link list. - Turn off Registration for State Change MB in loop mode. Signed-off-by:
Quinn Tran <quinn.tran@cavium.com> Signed-off-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org>
-
Himanshu Madhani authored
With support for dual mode in the driver, this mode becomes dead code. Remove reverse_ini_mode from code. Signed-off-by:
-
Quinn Tran authored
Add switch to allow both Initiator Mode & Target mode to operate at the same time. Signed-off-by:
-
Quinn Tran authored
Currently code performs a full scan of the fabric for every RSCN. Its an expensive process in a noisy large SAN. This patch optimizes expensive fabric discovery process by scanning switch for the affected port when RSCN is received. Currently Initiator Mode code makes login/logout decision without knowledge of target mode. This causes driver and firmware to go out-of-sync. This framework synchronizes both initiator mode personality and target mode personality in making login/logout decision. This patch adds following capabilities in the driver - Send Notification Acknowledgement asynchronously. - Update session/fcport state asynchronously. - Create a session or fcport struct asynchronously. - Send GNL asynchronously. The command will ask FW to provide a list of FC Port entries FW knows about. - Send GPDB asynchronously. The command will ask FW to provide detail data of an FC Port FW knows about or perform ADISC to verify the state of the session. - Send GPNID asynchronously. The command will ask switch to provide WWPN for provided NPort ID. - Send GPSC asynchronously. The command will ask switch to provide registered port speed for provided WWPN. - Send GIDPN asynchronously. The command will ask the switch to provide Nport ID for provided WWPN. - In driver unload path, schedule all session for deletion and wait for deletion to complete before allowing driver unload to proceed. Signed-off-by:
-
Quinn Tran authored
Current code merges qla_tgt_sess and fc_port structure into single fc_port structure representing same I-T nexus. Signed-off-by:
-
Quinn Tran authored
Updated code with d_id from s_id for better readability and clarity. Signed-off-by:
Christoph Hellwig <hch@lst.de> [ bvanassche: fixed spelling of patch description ] Signed-off-by:
-
Quinn Tran authored
Callback for sp->done expects scsi_qla_host is passed in as argument, Instead qla_hw_data is passed in. Signed-off-by:
-
Himanshu Madhani authored
During initial implementation, tape support was included but not enabled by default on target. So far, we don't see any target customer requesting this support. Since this code is not being used actively, we want to remove it and we will add back if there are any request in future for SRR support. Signed-off-by:
Giridhar Malavali <giridhar.malavali@cavium.com> Reviewed-by:
-
Quinn Tran authored
Trace flags are useful during debugging crash dumps using crash utility. These trace flags makes it easier to understand various states a command has successfully completed. Signed-off-by:
-
Quinn Tran authored
Move code code which converts Task Mgmt Command flags for ATIO to TCM #defines, from qla2xxx driver to tcm_qla2xxx driver. Signed-off-by:
-
Quinn Tran authored
Signed-off-by:
-
- 08 Feb, 2017 6 commits
-
-
Bryant G. Ly authored
This patch adds internal LIO sgl limit since the driver already sets a max transfer limit on transport layer of 1MB to the client. Cc: stable@vger.kernel.org Tested-by:
Steven Royer <seroyer@linux.vnet.ibm.com> Signed-off-by:
Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by:
-
Nicholas Bellinger authored
This patch addresses a long standing bug where the commit phase of COMPARE_AND_WRITE would result in a se_cmd->cmd_kref reference leak if se_cmd->scsi_status returned non SAM_STAT_GOOD. This would manifest first as a lost SCSI response, and eventual hung task during fabric driver logout or re-login, as existing shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref to reach zero. To address this bug, compare_and_write_post() has been changed to drop the incorrect !cmd->scsi_status conditional that was preventing *post_ret = 1 for being set during non SAM_STAT_GOOD status. This patch has been tested with SAM_STAT_CHECK_CONDITION status from normal target_complete_cmd() callback path, as well as the incoming __target_execute_cmd() submission failure path when se_cmd->execute_cmd() returns non zero status. Reported-by:
Donald White <dew@datera.io> Cc: Donald White <dew@datera.io> Tested-by:
Gary Guo <ghg@datera.io> Cc: Gary Guo <ghg@datera.io> Reviewed-by:
-
Nicholas Bellinger authored
This patch addresses a long-standing bug with multi-session (eg: iscsi-target + iser-target) se_node_acl dynamic free withini transport_deregister_session(). This bug is caused when a storage endpoint is configured with demo-mode (generate_node_acls = 1 + cache_dynamic_acls = 1) initiators, and initiator login creates a new dynamic node acl and attaches two sessions to it. After that, demo-mode for the storage instance is disabled via configfs (generate_node_acls = 0 + cache_dynamic_acls = 0) and the existing dynamic acl is never converted to an explicit ACL. The end result is dynamic acl resources are released twice when the sessions are shutdown in transport_deregister_session(). If the storage instance is not changed to disable demo-mode, or the dynamic acl is converted to an explict ACL, or there is only a single session associated with the dynamic ACL, the bug is not triggered. To address this big, move the release of dynamic se_node_acl memory into target_complete_nacl() so it's only freed once when se_node_acl->acl_kref reaches zero. (Drop unnecessary list_del_init usage - HCH) Reported-by:
Rob Millner <rlm@daterainc.com> Tested-by:
-
Nicholas Bellinger authored
This patch fixes a bug where incoming task management requests can be explicitly aborted during an active LUN_RESET, but who's struct work_struct are canceled in-flight before execution. This occurs when core_tmr_drain_tmr_list() invokes cancel_work_sync() for the incoming se_tmr_req->task_cmd->work, resulting in cmd->work for target_tmr_work() never getting invoked and the aborted TMR waiting indefinately within transport_wait_for_tasks(). To address this case, perform a CMD_T_ABORTED check early in transport_generic_handle_tmr(), and invoke the normal path via transport_cmd_check_stop_to_fabric() to complete any TMR kthreads blocked waiting for CMD_T_STOP in transport_wait_for_tasks(). Also, move the TRANSPORT_ISTATE_PROCESSING assignment earlier into transport_generic_handle_tmr() so the existing check in core_tmr_drain_tmr_list() avoids attempting abort the incoming se_tmr_req->task_cmd->work if it has already been queued into se_device->tmr_wq. Reported-by:
-
Nicholas Bellinger authored
This patch adds the missing target_complete_cmd() SCSI status parameter change in target_xcopy_do_work(), that was originally missing in commit 926317de. It correctly propigates up the correct SCSI status during EXTENDED_COPY exception cases, instead of always using the hardcoded SAM_STAT_CHECK_CONDITION from original code. This is required for ESX host environments that expect to hit SAM_STAT_RESERVATION_CONFLICT for certain scenarios, and SAM_STAT_CHECK_CONDITION results in non-retriable status for these cases. Reported-by:
Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by:
-
Nicholas Bellinger authored
After the v4.2+ RCU conversion to se_node_acl->lun_entry_hlist, a BUG_ON() was added in core_enable_device_list_for_node() to detect when the located orig->se_lun_acl contains an existing se_lun_acl pointer reference. However, this scenario can happen when a dynamically generated NodeACL is being converted to an explicit NodeACL, when the explicit NodeACL contains a different LUN mapping than the default provided by the WWN endpoint. So instead of triggering BUG_ON(), go ahead and fail instead following the original pre RCU conversion logic. Reported-by:
Benjamin ESTRABAUD <ben.estrabaud@mpstor.com> Cc: Benjamin ESTRABAUD <ben.estrabaud@mpstor.com> Reviewed-by:
-
- 05 Feb, 2017 1 commit
-
-
Linus Torvalds authored
-
- 04 Feb, 2017 6 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fixes from Thomas Gleixner: - Prevent double activation of interrupt lines, which causes problems on certain interrupt controllers - Handle the fallout of the above because x86 (ab)uses the activation function to reconfigure interrupts under the hood. * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/irq: Make irq activate operations symmetric irqdomain: Avoid activating interrupts more than once
-
git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds authored
Pull KVM fix from Radim Krčmář: "Fix a regression that prevented migration between hosts with different XSAVE features even if the missing features were not used by the guest (for stable)" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: do not save guest-unsupported XSAVE state
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-miscLinus Torvalds authored
Pull char/misc driver fixes from Greg KH: "Here are two bugfixes that resolve some reported issues. One in the firmware loader, that should fix the much-reported problem of crashes with it. The other is a hyperv fix for a reported regression. Both have been in linux-next for a week or so with no reported issues" * tag 'char-misc-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: Drivers: hv: vmbus: finally fix hv_need_to_signal_on_read() firmware: fix NULL pointer dereference in __fw_load_abort()
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/stagingLinus Torvalds authored
Pull staging/IIO fixes from Greg KH: "Here are a few small IIO and one staging driver fix for 4.10-rc7. They fix some reported issues with the drivers. All of them have been in linux-next for a week or so with no reported issues" * tag 'staging-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: greybus: timesync: validate platform state callback iio: dht11: Use usleep_range instead of msleep for start signal iio: adc: palmas_gpadc: retrieve a valid iio_dev in suspend/resume iio: health: max30100: fixed parenthesis around FIFO count check iio: health: afe4404: retrieve a valid iio_dev in suspend/resume iio: health: afe4403: retrieve a valid iio_dev in suspend/resume
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usbLinus Torvalds authored
Pull USB fixes from Greg KH: "Here are some small USB fixes for some reported issues, and the usual number of new device ids for 4.10-rc7. All of these, except the last new device id, have been in linux-next for a while with no reported issues" * tag 'usb-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: USB: serial: pl2303: add ATEN device ID usb: gadget: f_fs: Assorted buffer overflow checks. USB: Add quirk for WORLDE easykey.25 MIDI keyboard usb: musb: Fix external abort on non-linefetch for musb_irq_work() usb: musb: Fix host mode error -71 regression USB: serial: option: add device ID for HP lt2523 (Novatel E371) USB: serial: qcserial: add Dell DW5570 QDL
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull SCSI fix from James Bottomley: "A single fix this time: a fix for a virtqueue removal bug which only appears to affect S390, but which results in the queue hanging forever thus causing the machine to fail shutdown" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: virtio_scsi: Reject commands when virtqueue is broken
-
- 03 Feb, 2017 16 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostLinus Torvalds authored
Pull virtio/vhost fixes from Michael S. Tsirkin: "Last minute fixes: - ARM DMA fix revert - vhost endian-ness fix - MAINTAINERS: email address change for Amit" * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: MAINTAINERS: update email address for Amit Shah vhost: fix initialization for vq->is_le Revert "vring: Force use of DMA API for ARM-based systems with legacy devices"
-
git://github.com/awilliam/linux-vfioLinus Torvalds authored
Pull VFIO fix from Alex Williamson: "Fix an error path in SPAPR IOMMU backend (Alexey Kardashevskiy)" * tag 'vfio-v4.10-rc7' of git://github.com/awilliam/linux-vfio: vfio/spapr: Fix missing mutex unlock when creating a window
-
Linus Torvalds authored
Merge fixes from Andrew Morton: "8 fixes" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: mm, fs: check for fatal signals in do_generic_file_read() fs: break out of iomap_file_buffered_write on fatal signals base/memory, hotplug: fix a kernel oops in show_valid_zones() mm/memory_hotplug.c: check start_pfn in test_pages_in_a_zone() jump label: pass kbuild_cflags when checking for asm goto support shmem: fix sleeping from atomic context kasan: respect /proc/sys/kernel/traceoff_on_warning zswap: disable changing params if init fails
-
Michal Hocko authored
do_generic_file_read() can be told to perform a large request from userspace. If the system is under OOM and the reading task is the OOM victim then it has an access to memory reserves and finishing the full request can lead to the full memory depletion which is dangerous. Make sure we rather go with a short read and allow the killed task to terminate. Link: http://lkml.kernel.org/r/20170201092706.9966-3-mhocko@kernel.orgSigned-off-by:
Michal Hocko <mhocko@suse.com> Reviewed-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Michal Hocko authored
Tetsuo has noticed that an OOM stress test which performs large write requests can cause the full memory reserves depletion. He has tracked this down to the following path __alloc_pages_nodemask+0x436/0x4d0 alloc_pages_current+0x97/0x1b0 __page_cache_alloc+0x15d/0x1a0 mm/filemap.c:728 pagecache_get_page+0x5a/0x2b0 mm/filemap.c:1331 grab_cache_page_write_begin+0x23/0x40 mm/filemap.c:2773 iomap_write_begin+0x50/0xd0 fs/iomap.c:118 iomap_write_actor+0xb5/0x1a0 fs/iomap.c:190 ? iomap_write_end+0x80/0x80 fs/iomap.c:150 iomap_apply+0xb3/0x130 fs/iomap.c:79 iomap_file_buffered_write+0x68/0xa0 fs/iomap.c:243 ? iomap_write_end+0x80/0x80 xfs_file_buffered_aio_write+0x132/0x390 [xfs] ? remove_wait_queue+0x59/0x60 xfs_file_write_iter+0x90/0x130 [xfs] __vfs_write+0xe5/0x140 vfs_write+0xc7/0x1f0 ? syscall_trace_enter+0x1d0/0x380 SyS_write+0x58/0xc0 do_syscall_64+0x6c/0x200 entry_SYSCALL64_slow_path+0x25/0x25 the oom victim has access to all memory reserves to make a forward progress to exit easier. But iomap_file_buffered_write and other callers of iomap_apply loop to complete the full request. We need to check for fatal signals and back off with a short write instead. As the iomap_apply delegates all the work down to the actor we have to hook into those. All callers that work with the page cache are calling iomap_write_begin so we will check for signals there. dax_iomap_actor has to handle the situation explicitly because it copies data to the userspace directly. Other callers like iomap_page_mkwrite work on a single page or iomap_fiemap_actor do not allocate memory based on the given len. Fixes: 68a9f5e7 ("xfs: implement iomap based buffered write path") Link: http://lkml.kernel.org/r/20170201092706.9966-2-mhocko@kernel.orgSigned-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by:
-
Toshi Kani authored
Reading a sysfs "memoryN/valid_zones" file leads to the following oops when the first page of a range is not backed by struct page. show_valid_zones() assumes that 'start_pfn' is always valid for page_zone(). BUG: unable to handle kernel paging request at ffffea017a000000 IP: show_valid_zones+0x6f/0x160 This issue may happen on x86-64 systems with 64GiB or more memory since their memory block size is bumped up to 2GiB. [1] An example of such systems is desribed below. 0x3240000000 is only aligned by 1GiB and this memory block starts from 0x3200000000, which is not backed by struct page. BIOS-e820: [mem 0x0000003240000000-0x000000603fffffff] usable Since test_pages_in_a_zone() already checks holes, fix this issue by extending this function to return 'valid_start' and 'valid_end' for a given range. show_valid_zones() then proceeds with the valid range. [1] 'Commit bdee237c ("x86: mm: Use 2GB memory block size on large-memory x86-64 systems")' Link: http://lkml.kernel.org/r/20170127222149.30893-3-toshi.kani@hpe.comSigned-off-by:
Toshi Kani <toshi.kani@hpe.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Zhang Zhen <zhenzhang.zhang@huawei.com> Cc: Reza Arbab <arbab@linux.vnet.ibm.com> Cc: David Rientjes <rientjes@google.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: <stable@vger.kernel.org> [4.4+] Signed-off-by:
-
Toshi Kani authored
Patch series "fix a kernel oops when reading sysfs valid_zones", v2. A sysfs memory file is created for each 2GiB memory block on x86-64 when the system has 64GiB or more memory. [1] When the start address of a memory block is not backed by struct page, i.e. a memory range is not aligned by 2GiB, reading its 'valid_zones' attribute file leads to a kernel oops. This issue was observed on multiple x86-64 systems with more than 64GiB of memory. This patch-set fixes this issue. Patch 1 first fixes an issue in test_pages_in_a_zone(), which does not test the start section. Patch 2 then fixes the kernel oops by extending test_pages_in_a_zone() to return valid [start, end). Note for stable kernels: The memory block size change was made by commit bdee237c ("x86: mm: Use 2GB memory block size on large-memory x86-64 systems"), which was accepted to 3.9. However, this patch-set depends on (and fixes) the change to test_pages_in_a_zone() made by commit 5f0f2887 ("mm/memory_hotplug.c: check for missing sections in test_pages_in_a_zone()"), which was accepted to 4.4. So, I recommend that we backport it up to 4.4. [1] 'Commit bdee237c ("x86: mm: Use 2GB memory block size on large-memory x86-64 systems")' This patch (of 2): test_pages_in_a_zone() does not check 'start_pfn' when it is aligned by section since 'sec_end_pfn' is set equal to 'pfn'. Since this function is called for testing the range of a sysfs memory file, 'start_pfn' is always aligned by section. Fix it by properly setting 'sec_end_pfn' to the next section pfn. Also make sure that this function returns 1 only when the range belongs to a zone. Link: http://lkml.kernel.org/r/20170127222149.30893-2-toshi.kani@hpe.comSigned-off-by:
-
David Lin authored
Some versions of ARM GCC compiler such as Android toolchain throws in a '-fpic' flag by default. This causes the gcc-goto check script to fail although some config would have '-fno-pic' flag in the KBUILD_CFLAGS. This patch passes the KBUILD_CFLAGS to the check script so that the script does not rely on the default config from different compilers. Link: http://lkml.kernel.org/r/20170120234329.78868-1-dtwlin@google.comSigned-off-by:
David Lin <dtwlin@google.com> Acked-by:
Steven Rostedt <rostedt@goodmis.org> Cc: Michal Marek <mmarek@suse.com> Signed-off-by:
-
Kirill A. Shutemov authored
Syzkaller fuzzer managed to trigger this: BUG: sleeping function called from invalid context at mm/shmem.c:852 in_atomic(): 1, irqs_disabled(): 0, pid: 529, name: khugepaged 3 locks held by khugepaged/529: #0: (shrinker_rwsem){++++..}, at: [<ffffffff818d7ef1>] shrink_slab.part.59+0x121/0xd30 mm/vmscan.c:451 #1: (&type->s_umount_key#29){++++..}, at: [<ffffffff81a63630>] trylock_super+0x20/0x100 fs/super.c:392 #2: (&(&sbinfo->shrinklist_lock)->rlock){+.+.-.}, at: [<ffffffff818fd83e>] spin_lock include/linux/spinlock.h:302 [inline] #2: (&(&sbinfo->shrinklist_lock)->rlock){+.+.-.}, at: [<ffffffff818fd83e>] shmem_unused_huge_shrink+0x28e/0x1490 mm/shmem.c:427 CPU: 2 PID: 529 Comm: khugepaged Not tainted 4.10.0-rc5+ #201 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: shmem_undo_range+0xb20/0x2710 mm/shmem.c:852 shmem_truncate_range+0x27/0xa0 mm/shmem.c:939 shmem_evict_inode+0x35f/0xca0 mm/shmem.c:1030 evict+0x46e/0x980 fs/inode.c:553 iput_final fs/inode.c:1515 [inline] iput+0x589/0xb20 fs/inode.c:1542 shmem_unused_huge_shrink+0xbad/0x1490 mm/shmem.c:446 shmem_unused_huge_scan+0x10c/0x170 mm/shmem.c:512 super_cache_scan+0x376/0x450 fs/super.c:106 do_shrink_slab mm/vmscan.c:378 [inline] shrink_slab.part.59+0x543/0xd30 mm/vmscan.c:481 shrink_slab mm/vmscan.c:2592 [inline] shrink_node+0x2c7/0x870 mm/vmscan.c:2592 shrink_zones mm/vmscan.c:2734 [inline] do_try_to_free_pages+0x369/0xc80 mm/vmscan.c:2776 try_to_free_pages+0x3c6/0x900 mm/vmscan.c:2982 __perform_reclaim mm/page_alloc.c:3301 [inline] __alloc_pages_direct_reclaim mm/page_alloc.c:3322 [inline] __alloc_pages_slowpath+0xa24/0x1c30 mm/page_alloc.c:3683 __alloc_pages_nodemask+0x544/0xae0 mm/page_alloc.c:3848 __alloc_pages include/linux/gfp.h:426 [inline] __alloc_pages_node include/linux/gfp.h:439 [inline] khugepaged_alloc_page+0xc2/0x1b0 mm/khugepaged.c:750 collapse_huge_page+0x182/0x1fe0 mm/khugepaged.c:955 khugepaged_scan_pmd+0xfdf/0x12a0 mm/khugepaged.c:1208 khugepaged_scan_mm_slot mm/khugepaged.c:1727 [inline] khugepaged_do_scan mm/khugepaged.c:1808 [inline] khugepaged+0xe9b/0x1590 mm/khugepaged.c:1853 kthread+0x326/0x3f0 kernel/kthread.c:227 ret_from_fork+0x31/0x40 arch/x86/entry/entry_64.S:430 The iput() from atomic context was a bad idea: if after igrab() somebody else calls iput() and we left with the last inode reference, our iput() would lead to inode eviction and therefore sleeping. This patch should fix the situation. Link: http://lkml.kernel.org/r/20170131093141.GA15899@node.shutemov.nameSigned-off-by:Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Peter Zijlstra authored
After much waiting I finally reproduced a KASAN issue, only to find my trace-buffer empty of useful information because it got spooled out :/ Make kasan_report honour the /proc/sys/kernel/traceoff_on_warning interface. Link: http://lkml.kernel.org/r/20170125164106.3514-1-aryabinin@virtuozzo.comSigned-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Acked-by:
Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Dan Streetman authored
Add zswap_init_failed bool that prevents changing any of the module params, if init_zswap() fails, and set zswap_enabled to false. Change 'enabled' param to a callback, and check zswap_init_failed before allowing any change to 'enabled', 'zpool', or 'compressor' params. Any driver that is built-in to the kernel will not be unloaded if its init function returns error, and its module params remain accessible for users to change via sysfs. Since zswap uses param callbacks, which assume that zswap has been initialized, changing the zswap params after a failed initialization will result in WARNING due to the param callbacks expecting a pool to already exist. This prevents that by immediately exiting any of the param callbacks if initialization failed. This was reported here: https://marc.info/?l=linux-mm&m=147004228125528&w=4 And fixes this WARNING: [ 429.723476] WARNING: CPU: 0 PID: 5140 at mm/zswap.c:503 __zswap_pool_current+0x56/0x60 The warning is just noise, and not serious. However, when init fails, zswap frees all its percpu dstmem pages and its kmem cache. The kmem cache might be serious, if kmem_cache_alloc(NULL, gfp) has problems; but the percpu dstmem pages are definitely a problem, as they're used as temporary buffer for compressed pages before copying into place in the zpool. If the user does get zswap enabled after an init failure, then zswap will likely Oops on the first page it tries to compress (or worse, start corrupting memory). Fixes: 90b0fc26 ("zswap: change zpool/compressor at runtime") Link: http://lkml.kernel.org/r/20170124200259.16191-2-ddstreet@ieee.orgSigned-off-by:
Dan Streetman <dan.streetman@canonical.com> Reported-by:
Marcin Miroslaw <marcin@mejor.pl> Cc: Seth Jennings <sjenning@redhat.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: Minchan Kim <minchan@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Linus Torvalds authored
Merge tag 'regulator-fix-v4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator Pull regulator fixes from Mark Brown: "Three changes here: two run of the mill driver specific fixes and a change from Mark Rutland which reverts some new device specific ACPI binding code which was added during the merge window as there are concerns about this sending the wrong signal about usage of regulators in ACPI systems" * tag 'regulator-fix-v4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: regulator: fixed: Revert support for ACPI interface regulator: axp20x: AXP806: Fix dcdcb being set instead of dcdce regulator: twl6030: fix range comparison, allowing vsel = 59
-
Amit Shah authored
I'm leaving my job at Red Hat, this email address will stop working next week. Update it to one that I will have access to later. Signed-off-by:
Amit Shah <amit.shah@redhat.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com>
-
Halil Pasic authored
Currently, under certain circumstances vhost_init_is_le does just a part of the initialization job, and depends on vhost_reset_is_le being called too. For this reason vhost_vq_init_access used to call vhost_reset_is_le when vq->private_data is NULL. This is not only counter intuitive, but also real a problem because it breaks vhost_net. The bug was introduced to vhost_net with commit 2751c988 ("vhost: cross-endian support for legacy devices"). The symptom is corruption of the vq's used.idx field (virtio) after VHOST_NET_SET_BACKEND was issued as a part of the vhost shutdown on a vq with pending descriptors. Let us make sure the outcome of vhost_init_is_le never depend on the state it is actually supposed to initialize, and fix virtio_net by removing the reset from vhost_vq_init_access. With the above, there is no reason for vhost_reset_is_le to do just half of the job. Let us make vhost_reset_is_le reinitialize is_le. Signed-off-by:
Halil Pasic <pasic@linux.vnet.ibm.com> Reported-by:
Michael A. Tebolt <miket@us.ibm.com> Reported-by:
Dr. David Alan Gilbert <dgilbert@redhat.com> Fixes: commit 2751c988 ("vhost: cross-endian support for legacy devices") Cc: <stable@vger.kernel.org> Signed-off-by:
Greg Kurz <groug@kaod.org> Tested-by:
-
Michael S. Tsirkin authored
This reverts commit c7070619. This has been shown to regress on some ARM systems: by forcing on DMA API usage for ARM systems, we have inadvertently kicked open a hornets' nest in terms of cache-coherency. Namely that unless the virtio device is explicitly described as capable of coherent DMA by firmware, the DMA APIs on ARM and other DT-based platforms will assume it is non-coherent. This turns out to cause a big problem for the likes of QEMU and kvmtool, which generate virtio-mmio devices in their guest DTs but neglect to add the often-overlooked "dma-coherent" property; as a result, we end up with the guest making non-cacheable accesses to the vring, the host doing so cacheably, both talking past each other and things going horribly wrong. We are working on a safer work-around. Fixes: c7070619 ("vring: Force use of DMA API for ARM-based systems with legacy devices") Reported-by:
Robin Murphy <robin.murphy@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com>
-
Greg Kroah-Hartman authored
Merge tag 'usb-serial-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus Johan writes: USB-serial fixes for v4.10-rc7 One more device ID for pl2303. Signed-off-by:
Johan Hovold <johan@kernel.org>
-
