alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.

Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no limit on number of MD5 keys an application can attach to a
tcp socket.

This patch adds a per tcp socket limit based
on /proc/sys/net/core/optmem_max

With current default optmem_max values, this allows about 150 keys on
64bit arches, and 88 keys on 32bit arches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to be able to support proper RST messages for TCP MD5 flows, we
need to allow access to MD5 keys without locking listener socket.

This conversion is a nice cleanup, and shrinks size of timewait sockets
by 80 bytes.

IPv6 code reuses generic code found in IPv4 instead of duplicating it.

Control path uses GFP_KERNEL allocations instead of GFP_ATOMIC.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Shawn Lu <shawn.lu@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We no longer use md5_add() method from struct tcp_sock_af_ops
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl8169_get_regs operates under RTNL and rtl task mutex whereas
rtl_set_rx_mode is either called under RTNL or rtl task mutex protection.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Simpler, more consistent, with negligible cost in non-critical paths.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>

- atomic bit operations are globally visible
- pending status is always cleared before execution
- scheduled works are either idempotent or only required to happen once
  after a series of originating events, say link events for instance
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>

With infinite gratitude to Eric Dumazet for allowing me to identify
the error.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>

   text	   data	    bss	    dec	    hex	filename
8455963	 532732	1810804	10799499 a4c98b	vmlinux.o.before
8448899	 532732	1810804	10792435 a4adf3	vmlinux.o

This change also removes commented-out copy of __nlmsg_put
which was last touched in 2005 with "Enable once all users
have been converted" comment on top.

Changes in v2: rediffed against net-next.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC5722 Section 4 was amended by Errata 3089

Our implementation did the right thing anyway...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ability to return neighbour proxies list to caller if
it sent full ndmsg structure and has NTF_PROXY flag set.

Before this patch (and before iproute2 patches):
$ ip neigh add proxy 2001::1 dev eth0
$ ip -6 neigh show
$

After it and with applied iproute2 patches:
$ ip neigh add proxy 2001::1 dev eth0
$ ip -6 neigh show
2001::1 dev eth0  proxy
$

Compatibility with old versions of iproute2 is not broken,
kernel checks for incoming structure size and properly
works if old structure is came.

[v2]
* changed comments style.
* removed useless line with continue and curly bracket.
* changed incoming message size check from equal to more or
  equal.

CC: davem@davemloft.net
CC: kuznet@ms2.inr.ac.ru
CC: netdev@vger.kernel.org
CC: xemul@parallels.com
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This code is clearly unused, since it has a #error right
in it.  Given the vintage of sun3 hardware, it is probably
safe to assume that there is little interest in adding new
functionality to the driver now, so just delete the unused
block of code.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Sam Creasey <sammy@sammy.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The reorganization of the driver layout in drivers/net
left behind some stale paths in comments and in Kconfig
help text.  Bring them up to date.  No actual change to
any code takes place here.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function returns the page offset of the buffer, which can be
calculated based on either its DMA address or its virtual address.  It
used to use the virtual address and we would cast that to unsigned
long, as anything smaller would result in a compiler warning.  Now
that it's using the DMA address we should use unsigned int, matching
the return type.  It is also unnecessary to use __force.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

<linux/mtd/mtd.h> no longer defines DEBUG so we do not need to
un-define it here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

It's only used to get at neigh->primary_key, which in this context is
always going to be the same as rt->rt6i_gateway.
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead, compute it as-needed inside of that function using
dst_neigh_lookup().
Signed-off-by: David S. Miller <davem@davemloft.net>

In this specific situation we know we are dealing with a gatewayed route
and therefore rt6i_gateway is not going to be in6addr_any even in future
interpretations.
Signed-off-by: David S. Miller <davem@davemloft.net>

Now all code paths grab a local reference to the neigh, so if neigh
is not NULL we unconditionally release it at the end.  The old logic
would only release if we didn't have a non-NULL 'rt'.
Signed-off-by: David S. Miller <davem@davemloft.net>

The conversion is very similar to that made to ipv6's SIT code.
Signed-off-by: David S. Miller <davem@davemloft.net>

The irq handler was a mess.

See 7ab87ff4 ("via-rhine: move work from
irq handler to softirq and beyond") for similar changes. One can notice:
- all non-napi tasks are explicitely scheduled trough a single work queue.
- hiding software tx queue start behind the rtl_hw_start method is mildly
  natural. Move it in the caller where needed.
- as can be seen from the heavy use of bh disabling locks, the driver is
  not safe for irq context messages with netconsole. It is still quite
  usable for general messaging though. Tested ok with concurrent registers
  dump (ethtool -d) + background traffic + "echo t > /proc/sysrq-trigger".

Tested with old PCI chipset, PCIe 8168 and 810x:
- XID 0c900800 RTL8168evl/8111evl
- XID 18000000 RTL8168b/8111b
- XID 98000000 RTL8169sc/8110sc
- XID 083000c0 RTL8168d/8111d
- XID 081000c0 RTL8168d/8111d
- XID 00b00000 RTL8105e
- XID 04a00000 RTL8102e

As a side note, the comments in f11a377b
("r8169: avoid losing MSI interrupts") does not seem completely clear: if
I hack the driver further to stop acking the irq link event bit, MSI
interrupts keep being delivered (RTL8168b/8111b, XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Though motivated by the move of the driver to a single work queue of
sequential events and removal of hard irq processing, it looks safe as
a standalone change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

I see no good reason to keep both rtl8169_reinit_task and rtl8169_reset_task:
- rtl8169_reinit_task adds a software failure point which does relate to
  any hardware state
- they handle hardware the same. Remember that rtl8169_reinit_task was
  introduced in the 8169 only era to handle PCI errors way before the 8168
  asked for pll and firmware ops and compare :

      rtl8169_reinit_task     |    rtl8169_reset_task
  ----------------------------+--------------------------
  rtl8169_wait_for_quiescence | rtl8169_hw_reset
  rtl8169_update_counters     | rtl8169_wait_for_quiescence
  rtl8169_hw_reset            | rtl_hw_start
  rtl8169_rx_missed           | rtl8169_check_link_status
  rtl_pll_power_down          |
  rtl_request_firmware        |
  rtl8169_init_phy            |
  rtl_pll_power_up            |
  rtl_hw_start                |
  rtl8169_check_link_status   |
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The generic lib.c file contains code relative to the various MACs, NVM and
Manageability supported by the driver.  This patch splits the file into
three which are specific to those areas similar to how the PHY-specific
code is in phy.c and code specific to the 80003es2lan, 8257x, and ichX
MAC families are in their own files.  The generic code that is applicable
to all MAC/PHY parts supported by the driver remains in netdev.c, param.c
and ethtool.c files.  No change in functionality, just moving code
around for ease of maintenance, with some whitespace and other checkpatch
cleanups.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

__er16flash() is not meant to be called directly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Convert the last instances of strncpy() to the preferred strlcpy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

To ease searching for debug message strings, concatenate strings that span
multiple lines even if the resulting line exceeds 80 columns; these will
not cause checkpatch warnings.

Also, add '\n' and remove unnecessary '\r' from a few debug strings.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When setting the Low Power Link Up (LPLU, a.k.a. reverse auto-negotiation)
on 82577/8278/82579, do not restart auto-negotiation if reset of the Phy is
blocked by the Manageability Engine.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

During bi-directional stress on some 82566/82567 devices, some received
packets were dropped.  Increasing the Receive Packet Buffer Allocation
resolves this.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>