Eliminate some boilerplate code by using module_spi_driver() instead of
->init() / ->exit(), moving the salient bits from ->init() into ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When dev_<level>() macros are used against SPI device, the driver's name
is printed as well. No need to duplicate this explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace open coded netdev_<level>() macros.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ->probe() and ->remove() stages can be easily debugged with
initcall_debug or function tracer. There is no need to repeat the same
explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the DT-specific of_get_mac_address() function with
device_get_mac_address, which works on both DT and ACPI platforms.
This change makes it easier to add ACPI support.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv4 has icmp_echo_ignore_broadcast to prevent responding to broadcast pings.
IPv6 needs a similar mechanism.

v1->v2:
- Remove NET_IPV6_ICMP_ECHO_IGNORE_MULTICAST.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warning:

drivers/net/ethernet/pasemi/pasemi_mac.c:1842:5: warning:
 symbol 'pasemi_mac_init_module' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the request socket is created locally, it'd make more sense to
use reqsk_free() instead of reqsk_put() in TFO and syncookies' error
path.

However, tcp_get_cookie_sock() may set ->rsk_refcnt before freeing the
socket; tcp_conn_request() may also have non-null ->rsk_refcnt because
of tcp_try_fastopen(). In both cases 'req' hasn't been exposed
to the outside world and is safe to free immediately, but that'd
trigger the WARN_ON_ONCE in reqsk_free().

Define __reqsk_free() for these situations where we know nobody's
referencing the socket, even though ->rsk_refcnt might be non-null.
Now we can consolidate the error path of tcp_get_cookie_sock() and
tcp_conn_request().
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warning:

net/core/datagram.c:411:5: warning:
 symbol '__skb_datagram_iter' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warning:

drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c:407:6:
 warning: symbol 'hclgevf_update_link_mode' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warning:
drivers/net/ethernet/ibm/ibmveth.c:96:21:
 warning: symbol 'ibmveth_stats' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP ipv6 fast path dereferences a pointer to get to the inet6
part of a tcp socket, but given the fixed memory placement,
we can do better and avoid a possible cache line miss.

This also reduces register pressure, since we let the compiler
know about this memory placement.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ibmvnic driver currently reports a fixed value for both speed and
duplex settings regardless of the actual backing device that is being
used. By adding support to the QUERY_PHYS_PARMS command defined by the
PAPR+ we can query the current physical port state and report the proper
values for these feilds.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, a multicast stream may start out using replicast, because
there are few destinations, and then it should ideally switch to
L2/broadcast IGMP/multicast when the number of destinations grows beyond
a certain limit. The opposite should happen when the number decreases
below the limit.

To eliminate the risk of message reordering caused by method change,
a sending socket must stick to a previously selected method until it
enters an idle period of 5 seconds. Means there is a 5 seconds pause
in the traffic from the sender socket.

If the sender never makes such a pause, the method will never change,
and transmission may become very inefficient as the cluster grows.

With this commit, we allow such a switch between replicast and
broadcast without any need for a traffic pause.

Solution is to send a dummy message with only the header, also with
the SYN bit set, via broadcast or replicast. For the data message,
the SYN bit is set and sending via replicast or broadcast (inverse
method with dummy).

Then, at receiving side any messages follow first SYN bit message
(data or dummy message), they will be held in deferred queue until
another pair (dummy or data message) arrived in other link.

v2: reverse christmas tree declaration
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

As a preparation for introducing a smooth switching between replicast
and broadcast method for multicast message, We have to introduce a new
capability flag TIPC_MCAST_RBCTL to handle this new feature.

During a cluster upgrade a node can come back with this new capabilities
which also must be reflected in the cluster capabilities field.
The new feature is only applicable if all node in the cluster supports
this new capability.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, a multicast stream uses either broadcast or replicast as
transmission method, based on the ratio between number of actual
destinations nodes and cluster size.

However, when an L2 interface (e.g., VXLAN) provides pseudo
broadcast support, this becomes very inefficient, as it blindly
replicates multicast packets to all cluster/subnet nodes,
irrespective of whether they host actual target sockets or not.

The TIPC multicast algorithm is able to distinguish real destination
nodes from other nodes, and hence provides a smarter and more
efficient method for transferring multicast messages than
pseudo broadcast can do.

Because of this, we now make it possible for users to force
the broadcast link to permanently switch to using replicast,
irrespective of which capabilities the bearer provides,
or pretend to provide.
Conversely, we also make it possible to force the broadcast link
to always use true broadcast. While maybe less useful in
deployed systems, this may at least be useful for testing the
broadcast algorithm in small clusters.

We retain the current AUTOSELECT ability, i.e., to let the broadcast link
automatically select which algorithm to use, and to switch back and forth
between broadcast and replicast as the ratio between destination
node number and cluster size changes. This remains the default method.

Furthermore, we make it possible to configure the threshold ratio for
such switches. The default ratio is now set to 10%, down from 25% in the
earlier implementation.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable is never used.

CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
CC: virtualization@lists.linux-foundation.org
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide an explanation of what is expected with respect to sending new
versions of specific patches within a patch series, as well as what
happens if an earlier patch series accidentally gets merged).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: fixes 2019-03-18

please apply the following three patches to -net. The first two are fixes
for minor race conditions in the probe code, while the third one gets
dropwatch working (again).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

As part of the TX completion path, qeth_release_skbs() frees the completed
skbs with __skb_queue_purge(). This ends in kfree_skb(), reporting every
completed skb as dropped.
On the other hand when dropping an skb in .ndo_start_xmit, we end up
calling consume_skb()... where we should be using kfree_skb() so that
drop monitors get notified.

Switch the drop/consume logic around, and also don't accumulate dropped
packets in the tx_errors statistics.

Fixes: dc149e37 ("s390/qeth: replace open-coded skb_queue_walk()")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ucast IP table is utilized by some of the L3-specific sysfs attributes
that qeth_l3_create_device_attributes() provides. So initialize the table
_before_ registering the attributes.

Fixes: ebccc739 ("s390/qeth: add missing hash table initializations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The HW trap and VNICC configuration is exposed via sysfs, and may have
already been modified when qeth_l?_probe_device() attempts to initialize
them. So (1) initialize the VNICC values a little earlier, and (2) don't
bother about the HW trap mode, it was already initialized before.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The device ID alone does not uniquely identify a device.  Test both the
vendor and device ID to make sure we don't mistakenly think some other
vendor's 0xB410 device is a Digium HFC4S.  Also, instead of the bare hex
ID, use the same constant (PCI_DEVICE_ID_DIGIUM_HFC4S) used in the device
ID table.

No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: fix ignoring asoc_id for tcp-style sockets on some setsockopts

This is a patchset to fix ignoring asoc_id for tcp-style sockets on
some setsockopts, introduced by SCTP_CURRENT_ASSOC of the patchset:

  [net-next,00/24] sctp: support SCTP_FUTURE/CURRENT/ALL_ASSOC
  (https://patchwork.ozlabs.org/cover/1031706/)

As Marcelo suggested, we fix it on each setsockopt that is using
SCTP_CURRENT_ASSOC one by one by adding the check:

    if (sctp_style(sk, TCP))
        	xxx.xxx_assoc_id = SCTP_FUTURE_ASSOC;

so that assoc_id will be completely ingored for tcp-style socket on
setsockopts, and works as SCTP_FUTURE_ASSOC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_STREAM_SCHEDULER sockopt.

Fixes: 7efba10d ("sctp: add SCTP_FUTURE_ASOC and SCTP_CURRENT_ASSOC for SCTP_STREAM_SCHEDULER sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_EVENT sockopt.

Fixes: d251f05e ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_EVENT sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_ENABLE_STREAM_RESET sockopt.

Fixes: 99a62135 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_ENABLE_STREAM_RESET sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_DEFAULT_PRINFO sockopt.

Fixes: 3a583059 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_DEFAULT_PRINFO sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_DEACTIVATE_KEY sockopt.

Fixes: 2af66ff3 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_DEACTIVATE_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_DELETE_KEY sockopt.

Fixes: 3adcc300 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_DELETE_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_ACTIVE_KEY sockopt.

Fixes: bf9fb6ad ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_ACTIVE_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_KEY sockopt.

Fixes: 7fb3be13 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_MAX_BURST sockopt.

Fixes: e0651a0d ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_MAX_BURST sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_CONTEXT sockopt.

Fixes: 49b037ac ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_CONTEXT sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_DEFAULT_SNDINFO sockopt.

Fixes: 92fc3bd9 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_DEFAULT_SNDINFO sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_DELAYED_SACK sockopt.

Fixes: 9c5829e1 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_DELAYED_SACK sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently if the user pass an invalid asoc_id to SCTP_DEFAULT_SEND_PARAM
on a TCP-style socket, it will silently ignore the new parameters.
That's because after not finding an asoc, it is checking asoc_id against
the known values of CURRENT/FUTURE/ALL values and that fails to match.

IOW, if the user supplies an invalid asoc id or not, it should either
match the current asoc or the socket itself so that it will inherit
these later. Fixes it by forcing asoc_id to SCTP_FUTURE_ASSOC in case it
is a TCP-style socket without an asoc, so that the values get set on the
socket.

Fixes: 707e45b3 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_DEFAULT_SEND_PARAM sockopt")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now sctp_copy_descendant() copies pd_lobby from old sctp scok to new
sctp sock. If sctp_sock_migrate() returns error, it will panic when
releasing new sock and trying to purge pd_lobby due to the incorrect
pointers in pd_lobby.

  [  120.485116] kasan: CONFIG_KASAN_INLINE enabled
  [  120.486270] kasan: GPF could be caused by NULL-ptr deref or user
  [  120.509901] Call Trace:
  [  120.510443]  sctp_ulpevent_free+0x1e8/0x490 [sctp]
  [  120.511438]  sctp_queue_purge_ulpevents+0x97/0xe0 [sctp]
  [  120.512535]  sctp_close+0x13a/0x700 [sctp]
  [  120.517483]  inet_release+0xdc/0x1c0
  [  120.518215]  __sock_release+0x1d2/0x2a0
  [  120.519025]  sctp_do_peeloff+0x30f/0x3c0 [sctp]

We fix it by not copying sctp_sock pd_lobby in sctp_copy_descendan(),
and skb_queue_head_init() can also be removed in sctp_sock_migrate().

Reported-by: syzbot+85e0b422ff140b03672a@syzkaller.appspotmail.com
Fixes: 89664c62 ("sctp: sctp_sock_migrate() returns error if sctp_bind_addr_dup() fails")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp_hdr(skb) only works when skb->transport_header is set properly.

But in Netfilter, skb->transport_header for ipv6 is not guaranteed
to be right value for sctphdr. It would cause to fail to check the
checksum for sctp packets.

So fix it by using offset, which is always right in all places.

v1->v2:
  - Fix the changelog.

Fixes: e6d8b64b ("net: sctp: fix and consolidate SCTP checksumming code")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>