dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Oliver Neukum <oneukum@suse.de>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Johan Hovold <jhovold@gmail.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
CC: Simon Arlott <simon@fire.lp0.eu>
CC: Andrew Worsley <amworsley@gmail.com>
CC: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Gary Brubaker <xavyer@ix.netcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Peter Berger <pberger@brimson.com>
CC: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Lonnie Mendez <dignome@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Johan Hovold <jhovold@gmail.com>
CC: Preston Fick <preston.fick@silabs.com>
CC: Yuri Matylitski <ym@tekinsoft.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was used a lot a long time ago to trace code flow.  Now that we have
ftrace, this isn't needed at all, so remove these calls.

CC: William Greathouse <wgreathouse@smva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This removes most of the dbg() calls, as they were just tracing calls,
and converts the remaining ones to dev_dbg().
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the usage of dbg() to dev_dbg() where needed, and removed
a bunch of these calls where they were just "tracing" calls, which are
no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'for-usb-next-2012-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next

xhci: isoc, Intel xHCI, and suspend races.

Hi Greg,

Here's some xHCI fixes that should be queued for 3.5.

The first patch builds on Alan Stern's 3.4 patch to close the suspend and port
event race conditions.  It's marked for 3.4 stable, since that's where Alan's
patch landed.  The second patch fixes an incorrect error code that the xHCI
driver would return when an isochronous transfer error occurred.

The third and fourth patches fix issues seen on Intel xHCI host controllers.
The third patch fixes a dead port issue that was seen on the Panther Point
EHCI/xHCI host when CONFIG_USB_XHCI_HCD was turned off.  The ports were being
switched over to xHCI, even though the xHCI driver was never even built.  The
fourth patch adds support for the EHCI to xHCI port switchover for the upcoming
Intel Lynx Point chipset.

As I said, there's nothing here that's terribly urgent, and these patches can
wait a couple weeks for the 3.5 merge window.

Thanks,
Sarah Sharp

The upcoming Intel Lynx Point chipset includes an xHCI host controller
that can have ports switched from the EHCI host controller, just like
the Intel Panther Point xHCI host.  This time, ports from both EHCI
hosts can be switched to the xHCI host controller.  The PCI config
registers to do the port switching are in the exact same place in the
xHCI PCI configuration registers, with the same semantics.

Hooray for shipping patches for next-gen hardware before the current gen
hardware is even available for purchase!

This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

If the user chooses to say "no" to CONFIG_USB_XHCI_HCD on a system
with an Intel Panther Point chipset, the PCI quirks code or the EHCI
driver will switch the ports over to the xHCI host, but the xHCI driver
will never load.  The ports will be powered off and seem "dead" to the
user.

Fix this by only switching the ports over if CONFIG_USB_XHCI_HCD is
either compiled in, or compiled as a module.

This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Eric Anholt <eric.anholt@intel.com>
Reported-by: David Bein <d.bein@f5.com>
Cc: stable@vger.kernel.org

While testing unplugging an UVC HD webcam with usb-redirection (so through
usbdevfs), my userspace usb-redir code was getting a value of -1 in
iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt
is not a valid value.

The source of this -1 is the default case in xhci-ring.c:process_isoc_td()
adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR
in this case, so this patch adds handling for that completion code to
process_isoc_td().

This was observed and tested with the following xhci controller:
1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)

Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can
do, but since I cannot come up with anything better I've left that as is.

This patch should be backported to kernels as old as 2.6.36, which contain the
commit 04e51901 "USB: xHCI: Isochronous
transfer implementation".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

This commit adds a bit-array to xhci bus_state for keeping track of
which ports are undergoing a resume transition. If any of the bits
are set when xhci_hub_status_data() is called, the routine will return
a non-zero value even if no ports have any status changes pending.
This will allow usbcore to handle races between root-hub suspend and
port wakeup.

This patch should be backported to kernels as old as 3.4, that contain
the commit 879d38e6 "USB: fix race
between root-hub suspend and remote wakeup".
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org

The original request types in the cp210x driver are labled as "DEVICE_TO_HOST" and
"HOST_TO_DEVICE" but the actual bit definition corresponds to a request to the
interface. This has been corrected, and the actual definition for the device
requests have been added.
Signed-off-by: Preston Fick <preston.fick@silabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Zack Parsons <k3bacon@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Andrew Morton <akpm@linux-foundation.org>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Tobias Klauser <tklauser@distanz.ch>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: David Howells <dhowells@redhat.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>