- 17 May, 2016 33 commits
-
-
Anton Blanchard authored
[ Upstream commit b4c11211 ] In create_zero_mask() we have: addi %1,%2,-1 andc %1,%1,%2 popcntd %0,%1 using the "r" constraint for %2. r0 is a valid register in the "r" set, but addi X,r0,X turns it into an li: li r7,-1 andc r7,r7,r0 popcntd r4,r7 Fix this by using the "b" constraint, for which r0 is not a valid register. This was found with a kernel build using gcc trunk, narrowed down to when -frename-registers was enabled at -O2. It is just luck however that we aren't seeing this on older toolchains. Thanks to Segher for working with me to find this issue. Cc: stable@vger.kernel.org Fixes: d0cebfa6 ("powerpc: word-at-a-time optimization for 64-bit Little Endian") Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com>
-
K. Y. Srinivasan authored
[ Upstream commit 1db488d1 ] On the consumer side, we have interrupt driven flow management of the producer. It is sufficient to base the signaling decision on the amount of space that is available to write after the read is complete. The current code samples the previous available space and uses this in making the signaling decision. This state can be stale and is unnecessary. Since the state can be stale, we end up not signaling the host (when we should) and this can result in a hang. Fix this problem by removing the unnecessary check. I would like to thank Arseney Romanenko <arseneyr@microsoft.com> for pointing out this issue. Also, issue a full memory barrier before making the signaling descision to correctly deal with potential reordering of the write (read index) followed by the read of pending_sz. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Tested-by:
Dexuan Cui <decui@microsoft.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Christopher Oo authored
[ Upstream commit a5cca686 ] Fixes a bug where previously hv_ringbuffer_read would pass in the old number of bytes available to read instead of the expected old read index when calculating when to signal to the host that the ringbuffer is empty. Since the previous write size is already saved, also changes the hv_need_to_signal_on_read to use the previously read value rather than recalculating it. Signed-off-by:
Christopher Oo <t-chriso@microsoft.com> Signed-off-by:
-
Vitaly Kuznetsov authored
[ Upstream commit 822f18d4 ] Convert 6+-string comments repeating function names to normal kernel-style comments and fix a couple of other comment style issues. No textual or functional changes intended. Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
-
Al Viro authored
[ Upstream commit 10c64cea ] * if we have a hashed negative dentry and either CREAT|EXCL on r/o filesystem, or CREAT|TRUNC on r/o filesystem, or CREAT|EXCL with failing may_o_create(), we should fail with EROFS or the error may_o_create() has returned, but not ENOENT. Which is what the current code ends up returning. * if we have CREAT|TRUNC hitting a regular file on a read-only filesystem, we can't fail with EROFS here. At the very least, not until we'd done follow_managed() - we might have a writable file (or a device, for that matter) bound on top of that one. Moreover, the code downstream will see that O_TRUNC and attempt to grab the write access (*after* following possible mount), so if we really should fail with EROFS, it will happen. No need to do that inside atomic_open(). The real logics is much simpler than what the current code is trying to do - if we decided to go for simple lookup, ended up with a negative dentry *and* had create_error set, fail with create_error. No matter whether we'd got that negative dentry from lookup_real() or had found it in dcache. Cc: stable@vger.kernel.org # v3.6+ Acked-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Tony Luck authored
[ Upstream commit c4fc1956 ] Both of these drivers can return NOTIFY_BAD, but this terminates processing other callbacks that were registered later on the chain. Since the driver did nothing to log the error it seems wrong to prevent other interested parties from seeing it. E.g. neither of them had even bothered to check the type of the error to see if it was a memory error before the return NOTIFY_BAD. Signed-off-by:
Tony Luck <tony.luck@intel.com> Acked-by:
Aristeu Rozanski <aris@redhat.com> Acked-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/72937355dd92318d2630979666063f8a2853495b.1461864507.git.tony.luck@intel.comSigned-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit 2d2c038a ] Phoenix Audio MT202pcs (1de7:0114) and MT202exe (1de7:0013) need the same workaround as TMX320 for avoiding the firmware bug. It fixes the frequent error about the sample rate inquiries and the slow device probe as consequence. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117321 Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Naoya Horiguchi authored
[ Upstream commit f4c18e6f ] The race condition addressed in commit add05cec ("mm: soft-offline: don't free target page in successful page migration") was not closed completely, because that can happen not only for soft-offline, but also for hard-offline. Consider that a slab page is about to be freed into buddy pool, and then an uncorrected memory error hits the page just after entering __free_one_page(), then VM_BUG_ON_PAGE(page->flags & PAGE_FLAGS_CHECK_AT_PREP) is triggered, despite the fact that it's not necessary because the data on the affected page is not consumed. To solve it, this patch drops __PG_HWPOISON from page flag checks at allocation/free time. I think it's justified because __PG_HWPOISON flags is defined to prevent the page from being reused, and setting it outside the page's alloc-free cycle is a designed behavior (not a bug.) For recent months, I was annoyed about BUG_ON when soft-offlined page remains on lru cache list for a while, which is avoided by calling put_page() instead of putback_lru_page() in page migration's success path. This means that this patch reverts a major change from commit add05cec about the new refcounting rule of soft-offlined pages, so "reuse window" revives. This will be closed by a subsequent patch. Signed-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Dean Nelson <dnelson@redhat.com> Cc: Tony Luck <tony.luck@intel.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Hugh Dickins <hughd@google.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Naoya Horiguchi authored
[ Upstream commit add05cec ] Stress testing showed that soft offline events for a process iterating "mmap-pagefault-munmap" loop can trigger VM_BUG_ON(PAGE_FLAGS_CHECK_AT_PREP) in __free_one_page(): Soft offlining page 0x70fe1 at 0x70100008d000 Soft offlining page 0x705fb at 0x70300008d000 page:ffffea0001c3f840 count:0 mapcount:0 mapping: (null) index:0x2 flags: 0x1fffff80800000(hwpoison) page dumped because: VM_BUG_ON_PAGE(page->flags & ((1 << 25) - 1)) ------------[ cut here ]------------ kernel BUG at /src/linux-dev/mm/page_alloc.c:585! invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC Modules linked in: cfg80211 rfkill crc32c_intel microcode ppdev parport_pc pcspkr serio_raw virtio_balloon parport i2c_piix4 virtio_blk virtio_net ata_generic pata_acpi floppy CPU: 3 PID: 1779 Comm: test_base_madv_ Not tainted 4.0.0-v4.0-150511-1451-00009-g82360a3730e6 #139 RIP: free_pcppages_bulk+0x52a/0x6f0 Call Trace: drain_pages_zone+0x3d/0x50 drain_local_pages+0x1d/0x30 on_each_cpu_mask+0x46/0x80 drain_all_pages+0x14b/0x1e0 soft_offline_page+0x432/0x6e0 SyS_madvise+0x73c/0x780 system_call_fastpath+0x12/0x17 Code: ff 89 45 b4 48 8b 45 c0 48 83 b8 a8 00 00 00 00 0f 85 e3 fb ff ff 0f 1f 00 0f 0b 48 8b 7d 90 48 c7 c6 e8 95 a6 81 e8 e6 32 02 00 <0f> 0b 8b 45 cc 49 89 47 30 41 8b 47 18 83 f8 ff 0f 85 10 ff ff RIP [<ffffffff811a806a>] free_pcppages_bulk+0x52a/0x6f0 RSP <ffff88007a117d28> ---[ end trace 53926436e76d1f35 ]--- When soft offline successfully migrates page, the source page is supposed to be freed. But there is a race condition where a source page looks isolated (i.e. the refcount is 0 and the PageHWPoison is set) but somewhat linked to pcplist. Then another soft offline event calls drain_all_pages() and tries to free such hwpoisoned page, which is forbidden. This odd page state seems to happen due to the race between put_page() in putback_lru_page() and __pagevec_lru_add_fn(). But I don't want to play with tweaking drain code as done in commit 9ab3b598 "mm: hwpoison: drop lru_add_drain_all() in __soft_offline_page()", or to change page freeing code for this soft offline's purpose. Instead, let's think about the difference between hard offline and soft offline. There is an interesting difference in how to isolate the in-use page between these, that is, hard offline marks PageHWPoison of the target page at first, and doesn't free it by keeping its refcount 1. OTOH, soft offline tries to free the target page then marks PageHWPoison. This difference might be the source of complexity and result in bugs like the above. So making soft offline isolate with keeping refcount can be a solution for this problem. We can pass to page migration code the "reason" which shows the caller, so let's use this more to avoid calling putback_lru_page() when called from soft offline, which effectively does the isolation for soft offline. With this change, target pages of soft offline never be reused without changing migratetype, so this patch also removes the related code. Signed-off-by:
-
Minchan Kim authored
[ Upstream commit 7bf52fb8 ] We have been reclaimed highmem zone if buffer_heads is over limit but commit 6b4f7799 ("mm: vmscan: invoke slab shrinkers from shrink_zone()") changed the behavior so it doesn't reclaim highmem zone although buffer_heads is over the limit. This patch restores the logic. Fixes: 6b4f7799 ("mm: vmscan: invoke slab shrinkers from shrink_zone()") Signed-off-by:
Minchan Kim <minchan@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Konstantin Khlebnikov authored
[ Upstream commit 3486b85a ] Khugepaged detects own VMAs by checking vm_file and vm_ops but this way it cannot distinguish private /dev/zero mappings from other special mappings like /dev/hpet which has no vm_ops and popultes PTEs in mmap. This fixes false-positive VM_BUG_ON and prevents installing THP where they are not expected. Link: http://lkml.kernel.org/r/CACT4Y+ZmuZMV5CjSFOeXviwQdABAgT7T+StKfTqan9YDtgEi5g@mail.gmail.com Fixes: 78f11a25 ("mm: thp: fix /dev/zero MAP_PRIVATE and vm_flags cleanups") Signed-off-by:
Konstantin Khlebnikov <koct9i@gmail.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Jason Gunthorpe authored
[ Upstream commit e6bd18f5 ] The drivers/infiniband stack uses write() as a replacement for bi-directional ioctl(). This is not safe. There are ways to trigger write calls that result in the return structure that is normally written to user space being shunted off to user specified kernel memory instead. For the immediate repair, detect and deny suspicious accesses to the write API. For long term, update the user space libraries and the kernel API to something that doesn't present the same security vulnerabilities (likely a structured ioctl() interface). The impacted uAPI interfaces are generally only available if hardware from drivers/infiniband is installed in the system. Reported-by:
Jann Horn <jann@thejh.net> Signed-off-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> [ Expanded check to all known write() entry points ] Cc: stable@vger.kernel.org Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
James Morse authored
[ Upstream commit 625fe4f8 ] arm_cpuidle_suspend() may return -EOPNOTSUPP, or any value returned by the cpu_ops/cpuidle_ops suspend call. arm_enter_idle_state() doesn't update 'ret' with this value, meaning we always signal success to cpuidle_enter_state(), causing it to update the usage counters as if we succeeded. Fixes: 191de17a ("ARM64: cpuidle: Replace cpu_suspend by the common ARM/ARM64 function") Signed-off-by:
James Morse <james.morse@arm.com> Acked-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Cc: 4.1+ <stable@vger.kernel.org> # 4.1+ Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Sascha Hauer authored
[ Upstream commit 5616f367 ] The secondary CPU starts up in ARM mode. When the kernel is compiled in thumb2 mode we have to explicitly compile the secondary startup trampoline in ARM mode, otherwise the CPU will go to Nirvana. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Reported-by:
Steffen Trumtrar <s.trumtrar@pengutronix.de> Suggested-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: stable@vger.kernel.org Signed-off-by:
Dinh Nguyen <dinguyen@opensource.altera.com> Signed-off-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
-
Vitaly Prosyak authored
[ Upstream commit 5d5b7803 ] When crtc/timing is disabled on boot the dig block should be stopped in order ignore timing from crtc, reset the steering fifo otherwise we get display corruption or hung in dp sst mode. v2: agd: fix coding style Signed-off-by:
Vitaly Prosyak <vitaly.prosyak@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Ville Syrjälä authored
[ Upstream commit 4ea39590 ] Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around GPU hangs if the RPS EI/thresholds aren't suitably aligned. It seems like scheduling/timer interupts stop working somehow and things get stuck eg. in usleep_range(). I bisected the problem down to commit 8a586437 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function") I observed that before all the values were at least multiples of 25, but afterwards they are not. And rounding things up to the next multiple of 25 does seem to help, so lets' do that. I also tried roundup(..., 5) but that wasn't sufficient. Also I have no idea if we might need this sort of thing on gen9+ as well. These are the original EI/thresholds: LOW_POWER GEN6_RP_UP_EI 12500 GEN6_RP_UP_THRESHOLD 11800 GEN6_RP_DOWN_EI 25000 GEN6_RP_DOWN_THRESHOLD 21250 BETWEEN GEN6_RP_UP_EI 10250 GEN6_RP_UP_THRESHOLD 9225 GEN6_RP_DOWN_EI 25000 GEN6_RP_DOWN_THRESHOLD 18750 HIGH_POWER GEN6_RP_UP_EI 8000 GEN6_RP_UP_THRESHOLD 6800 GEN6_RP_DOWN_EI 25000 GEN6_RP_DOWN_THRESHOLD 15000 These are after 8a586437: LOW_POWER GEN6_RP_UP_EI 12500 GEN6_RP_UP_THRESHOLD 11875 GEN6_RP_DOWN_EI 25000 GEN6_RP_DOWN_THRESHOLD 21250 BETWEEN GEN6_RP_UP_EI 10156 GEN6_RP_UP_THRESHOLD 9140 GEN6_RP_DOWN_EI 25000 GEN6_RP_DOWN_THRESHOLD 18750 HIGH_POWER GEN6_RP_UP_EI 7812 GEN6_RP_UP_THRESHOLD 6640 GEN6_RP_DOWN_EI 25000 GEN6_RP_DOWN_THRESHOLD 15000 And these are what we have after this patch: LOW_POWER GEN6_RP_UP_EI 12500 GEN6_RP_UP_THRESHOLD 11875 GEN6_RP_DOWN_EI 25000 GEN6_RP_DOWN_THRESHOLD 21250 BETWEEN GEN6_RP_UP_EI 10175 GEN6_RP_UP_THRESHOLD 9150 GEN6_RP_DOWN_EI 25000 GEN6_RP_DOWN_THRESHOLD 18750 HIGH_POWER GEN6_RP_UP_EI 7825 GEN6_RP_UP_THRESHOLD 6650 GEN6_RP_DOWN_EI 25000 GEN6_RP_DOWN_THRESHOLD 15000 Cc: stable@vger.kernel.org Cc: Akash Goel <akash.goel@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B Fixes: 8a586437 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function") Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.comAcked-by:
Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
Patrik Jakobsson <patrik.jakobsson@linux.intel.com> (cherry picked from commit 8a292d01) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Imre Deak authored
[ Upstream commit 5eaa60c7 ] The driver's VDD on/off logic assumes that whenever the VDD is on we also hold an AUX power domain reference. Since BIOS can leave the VDD on during booting and resuming and on DDI platforms we won't take a corresponding power reference, the above assumption won't hold on those platforms and an eventual delayed VDD off work will do an extraneous AUX power domain put resulting in a refcount underflow. Fix this the same way we did this for non-DDI DP encoders: commit 6d93c0c4 ("drm/i915: fix VDD state tracking after system resume") At the same time call the DP encoder suspend handler the same way as the non-DDI DP encoders do to flush any pending VDD off work. Leaving the work running may cause a HW access where we don't expect this (at a point where power domains are suspended already). While at it remove an unnecessary function call indirection. This fixed for me AUX refcount underflow problems on BXT during suspend/resume. CC: Ville Syrjälä <ville.syrjala@linux.intel.com> CC: stable@vger.kernel.org Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
-
Michael Neuling authored
[ Upstream commit d6776bba ] Keep IRQ mappings on context teardown. This won't leak IRQs as if we allocate the mapping again, the generic code will give the same mapping used last time. Doing this works around a race in the generic code. Masking the interrupt introduces a race which can crash the kernel or result in IRQ that is never EOIed. The lost of EOI results in all subsequent mappings to the same HW IRQ never receiving an interrupt. We've seen this race with cxl test cases which are doing heavy context startup and teardown at the same time as heavy interrupt load. A fix to the generic code is being investigated also. Signed-off-by:
Michael Neuling <mikey@neuling.org> Cc: stable@vger.kernel.org # 3.8 Tested-by:
Andrew Donnellan <andrew.donnellan@au1.ibm.com> Acked-by:
Ian Munsie <imunsie@au1.ibm.com> Tested-by:
Vaibhav Jain <vaibhav@linux.vnet.ibm.com> Signed-off-by:
-
Lyude authored
[ Upstream commit 9dc0487d ] Some hubs are forgetful, and end up forgetting whatever GUID we set previously after we do a suspend/resume cycle. This can lead to hotplugging breaking (along with probably other things) since the hub will start sending connection notifications with the wrong GUID. As such, we need to check on resume whether or not the GUID the hub is giving us is valid. Signed-off-by:
Lyude <cpaul@redhat.com> Reviewed-by:
Harry Wentland <harry.wentland@amd.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1460580618-7421-1-git-send-email-cpaul@redhat.com Cc: stable@vger.kernel.org Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
cpaul@redhat.com authored
[ Upstream commit 263efde3 ] We can thank KASAN for finding this, otherwise I probably would have spent hours on it. This fixes a somewhat harder to trigger kernel panic, occuring while enabling MST where the port we were currently updating the payload on would have all of it's refs dropped before we finished what we were doing: ================================================================== BUG: KASAN: use-after-free in drm_dp_update_payload_part1+0xb3f/0xdb0 [drm_kms_helper] at addr ffff8800d29de018 Read of size 4 by task Xorg/973 ============================================================================= BUG kmalloc-2048 (Tainted: G B W ): kasan: bad access detected ----------------------------------------------------------------------------- INFO: Allocated in drm_dp_add_port+0x1aa/0x1ed0 [drm_kms_helper] age=16477 cpu=0 pid=2175 ___slab_alloc+0x472/0x490 __slab_alloc+0x20/0x40 kmem_cache_alloc_trace+0x151/0x190 drm_dp_add_port+0x1aa/0x1ed0 [drm_kms_helper] drm_dp_send_link_address+0x526/0x960 [drm_kms_helper] drm_dp_check_and_send_link_address+0x1ac/0x210 [drm_kms_helper] drm_dp_mst_link_probe_work+0x77/0xd0 [drm_kms_helper] process_one_work+0x562/0x1350 worker_thread+0xd9/0x1390 kthread+0x1c5/0x260 ret_from_fork+0x22/0x40 INFO: Freed in drm_dp_free_mst_port+0x50/0x60 [drm_kms_helper] age=7521 cpu=0 pid=2175 __slab_free+0x17f/0x2d0 kfree+0x169/0x180 drm_dp_free_mst_port+0x50/0x60 [drm_kms_helper] drm_dp_destroy_connector_work+0x2b8/0x490 [drm_kms_helper] process_one_work+0x562/0x1350 worker_thread+0xd9/0x1390 kthread+0x1c5/0x260 ret_from_fork+0x22/0x40 which on this T460s, would eventually lead to kernel panics in somewhat random places later in intel_mst_enable_dp() if we got lucky enough. Signed-off-by:
-
Roman Pen authored
[ Upstream commit 346c09f8 ] The bug in a workqueue leads to a stalled IO request in MQ ctx->rq_list with the following backtrace: [ 601.347452] INFO: task kworker/u129:5:1636 blocked for more than 120 seconds. [ 601.347574] Tainted: G O 4.4.5-1-storage+ #6 [ 601.347651] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 601.348142] kworker/u129:5 D ffff880803077988 0 1636 2 0x00000000 [ 601.348519] Workqueue: ibnbd_server_fileio_wq ibnbd_dev_file_submit_io_worker [ibnbd_server] [ 601.348999] ffff880803077988 ffff88080466b900 ffff8808033f9c80 ffff880803078000 [ 601.349662] ffff880807c95000 7fffffffffffffff ffffffff815b0920 ffff880803077ad0 [ 601.350333] ffff8808030779a0 ffffffff815b01d5 0000000000000000 ffff880803077a38 [ 601.350965] Call Trace: [ 601.351203] [<ffffffff815b0920>] ? bit_wait+0x60/0x60 [ 601.351444] [<ffffffff815b01d5>] schedule+0x35/0x80 [ 601.351709] [<ffffffff815b2dd2>] schedule_timeout+0x192/0x230 [ 601.351958] [<ffffffff812d43f7>] ? blk_flush_plug_list+0xc7/0x220 [ 601.352208] [<ffffffff810bd737>] ? ktime_get+0x37/0xa0 [ 601.352446] [<ffffffff815b0920>] ? bit_wait+0x60/0x60 [ 601.352688] [<ffffffff815af784>] io_schedule_timeout+0xa4/0x110 [ 601.352951] [<ffffffff815b3a4e>] ? _raw_spin_unlock_irqrestore+0xe/0x10 [ 601.353196] [<ffffffff815b093b>] bit_wait_io+0x1b/0x70 [ 601.353440] [<ffffffff815b056d>] __wait_on_bit+0x5d/0x90 [ 601.353689] [<ffffffff81127bd0>] wait_on_page_bit+0xc0/0xd0 [ 601.353958] [<ffffffff81096db0>] ? autoremove_wake_function+0x40/0x40 [ 601.354200] [<ffffffff81127cc4>] __filemap_fdatawait_range+0xe4/0x140 [ 601.354441] [<ffffffff81127d34>] filemap_fdatawait_range+0x14/0x30 [ 601.354688] [<ffffffff81129a9f>] filemap_write_and_wait_range+0x3f/0x70 [ 601.354932] [<ffffffff811ced3b>] blkdev_fsync+0x1b/0x50 [ 601.355193] [<ffffffff811c82d9>] vfs_fsync_range+0x49/0xa0 [ 601.355432] [<ffffffff811cf45a>] blkdev_write_iter+0xca/0x100 [ 601.355679] [<ffffffff81197b1a>] __vfs_write+0xaa/0xe0 [ 601.355925] [<ffffffff81198379>] vfs_write+0xa9/0x1a0 [ 601.356164] [<ffffffff811c59d8>] kernel_write+0x38/0x50 The underlying device is a null_blk, with default parameters: queue_mode = MQ submit_queues = 1 Verification that nullb0 has something inflight: root@pserver8:~# cat /sys/block/nullb0/inflight 0 1 root@pserver8:~# find /sys/block/nullb0/mq/0/cpu* -name rq_list -print -exec cat {} \; ... /sys/block/nullb0/mq/0/cpu2/rq_list CTX pending: ffff8838038e2400 ... During debug it became clear that stalled request is always inserted in the rq_list from the following path: save_stack_trace_tsk + 34 blk_mq_insert_requests + 231 blk_mq_flush_plug_list + 281 blk_flush_plug_list + 199 wait_on_page_bit + 192 __filemap_fdatawait_range + 228 filemap_fdatawait_range + 20 filemap_write_and_wait_range + 63 blkdev_fsync + 27 vfs_fsync_range + 73 blkdev_write_iter + 202 __vfs_write + 170 vfs_write + 169 kernel_write + 56 So blk_flush_plug_list() was called with from_schedule == true. If from_schedule is true, that means that finally blk_mq_insert_requests() offloads execution of __blk_mq_run_hw_queue() and uses kblockd workqueue, i.e. it calls kblockd_schedule_delayed_work_on(). That means, that we race with another CPU, which is about to execute __blk_mq_run_hw_queue() work. Further debugging shows the following traces from different CPUs: CPU#0 CPU#1 ---------------------------------- ------------------------------- reqeust A inserted STORE hctx->ctx_map[0] bit marked kblockd_schedule...() returns 1 <schedule to kblockd workqueue> request B inserted STORE hctx->ctx_map[1] bit marked kblockd_schedule...() returns 0 *** WORK PENDING bit is cleared *** flush_busy_ctxs() is executed, but bit 1, set by CPU#1, is not observed As a result request B pended forever. This behaviour can be explained by speculative LOAD of hctx->ctx_map on CPU#0, which is reordered with clear of PENDING bit and executed _before_ actual STORE of bit 1 on CPU#1. The proper fix is an explicit full barrier <mfence>, which guarantees that clear of PENDING bit is to be executed before all possible speculative LOADS or STORES inside actual work function. Signed-off-by:
Roman Pen <roman.penyaev@profitbricks.com> Cc: Gioh Kim <gi-oh.kim@profitbricks.com> Cc: Michael Wang <yun.wang@profitbricks.com> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: linux-block@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Conrad Kostecki authored
[ Upstream commit 037e1197 ] Fixes audio output on a ThinkPad X260, when using Lenovo CES 2013 docking station series (basic, pro, ultra). Signed-off-by:
Conrad Kostecki <ck+linuxkernel@bl4ckb0x.de> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Shaohua Li authored
[ Upstream commit 9c573de3 ] blk_queue_split marks bio unmergeable, which makes sense for normal bio. But if dispatching the bio to underlayer disk, the blk_queue_split checks are invalid, hence it's possible the bio becomes mergeable. In the reported bug, this bug causes trim against raid0 performance slash https://bugzilla.kernel.org/show_bug.cgi?id=117051Reported-and-tested-by:
Park Ju Hyung <qkrwngud825@gmail.com> Fixes: 6ac45aeb(block: avoid to merge splitted bio) Cc: stable@vger.kernel.org (v4.3+) Cc: Ming Lei <ming.lei@canonical.com> Cc: Neil Brown <neilb@suse.de> Reviewed-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Hans Verkuil authored
[ Upstream commit 3020ca71 ] The VSync polarity was negative instead of positive for the 4k CEA formats. I probably copy-and-pasted these from the DMT 4k format, which does have a negative VSync polarity. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Reported-by:
Martin Bugge <marbugge@cisco.com> Cc: <stable@vger.kernel.org> # for v4.1 and up Signed-off-by:
-
Jasem Mutlaq authored
[ Upstream commit 613ac23a ] Adding VID:PID for Straizona Focusers to cp210x driver. Signed-off-by:
Jasem Mutlaq <mutlaqja@ikarustech.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Mike Manning authored
[ Upstream commit 1d377f4d ] The Link ECU is an aftermarket ECU computer for vehicles that provides full tuning abilities as well as datalogging and displaying capabilities via the USB to Serial adapter built into the device. Signed-off-by:
Mike Manning <michael@bsch.com.au> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Laszlo Ersek authored
[ Upstream commit 630ba0cc ] The variable_matches() function can currently read "var_name[len]", for example when: - var_name[0] == 'a', - len == 1 - match_name points to the NUL-terminated string "ab". This function is supposed to accept "var_name" inputs that are not NUL-terminated (hence the "len" parameter"). Document the function, and access "var_name[*match]" only if "*match" is smaller than "len". Reported-by:
Laszlo Ersek <lersek@redhat.com> Cc: Peter Jones <pjones@redhat.com> Cc: Matthew Garrett <mjg59@coreos.com> Cc: Jason Andryuk <jandryuk@gmail.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: <stable@vger.kernel.org> # v3.10+ Link: http://thread.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/86906Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by:
-
Krzysztof Kozlowski authored
[ Upstream commit 07d2390e ] In certain probe conditions the interrupt came right after registering the handler causing a NULL pointer exception because of uninitialized waitqueue: $ udevadm trigger i2c-gpio i2c-gpio-1: using pins 143 (SDA) and 144 (SCL) i2c-gpio i2c-gpio-3: using pins 53 (SDA) and 52 (SCL) Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = e8b38000 [00000000] *pgd=00000000 Internal error: Oops: 5 [#1] SMP ARM Modules linked in: snd_soc_i2s(+) i2c_gpio(+) snd_soc_idma snd_soc_s3c_dma snd_soc_core snd_pcm_dmaengine snd_pcm snd_timer snd soundcore ac97_bus spi_s3c64xx pwm_samsung dwc2 exynos_adc phy_exynos_usb2 exynosdrm exynos_rng rng_core rtc_s3c CPU: 0 PID: 717 Comm: data-provider-m Not tainted 4.6.0-rc1-next-20160401-00011-g1b8d87473b9e-dirty #101 Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) (...) (__wake_up_common) from [<c0379624>] (__wake_up+0x38/0x4c) (__wake_up) from [<c0a41d30>] (ak8975_irq_handler+0x28/0x30) (ak8975_irq_handler) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140) (handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68) (handle_irq_event) from [<c0389c40>] (handle_edge_irq+0xf0/0x19c) (handle_edge_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34) (generic_handle_irq) from [<c05ee360>] (exynos_eint_gpio_irq+0x50/0x68) (exynos_eint_gpio_irq) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140) (handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68) (handle_irq_event) from [<c0389a70>] (handle_fasteoi_irq+0xb4/0x194) (handle_fasteoi_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34) (generic_handle_irq) from [<c03860b4>] (__handle_domain_irq+0x5c/0xb4) (__handle_domain_irq) from [<c0301774>] (gic_handle_irq+0x54/0x94) (gic_handle_irq) from [<c030c910>] (__irq_usr+0x50/0x80) The bug was reproduced on exynos4412-trats2 (with a max77693 device also using i2c-gpio) after building max77693 as a module. Cc: <stable@vger.kernel.org> Fixes: 94a6d5cf ("iio:ak8975 Implement data ready interrupt handling") Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Tested-by:
Gregor Boirie <gregor.boirie@parrot.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Jack Pham authored
[ Upstream commit dec8e8f6 ] Specifically for the case of reads that use the Extended Register Read Long command, a multi-byte read operation is broken up into 8-byte chunks. However the call to spmi_ext_register_readl() is incorrectly passing 'val_size', which if greater than 8 will always fail. The argument should instead be 'len'. Fixes: c9afbb05 ("regmap: spmi: support base and extended register spaces") Signed-off-by:
Jack Pham <jackp@codeaurora.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Srinivas Kandagatla authored
[ Upstream commit 17dcc37e ] On some SOCs PORTS_IMPL register value is never programmed by the firmware and left at zero value. Which means that no sata ports are available for software. AHCI driver used to cope up with this by fabricating the port_map if the PORTS_IMPL register is read zero, but recent patch broke this workaround as zero value was valid for NVMe disks. This patch adds ports-implemented DT bindings as workaround for this issue in a way that DT can can override the PORTS_IMPL register in cases where the firmware did not program it already. Fixes: 566d1827 ("libata: disable forced PORTS_IMPL for >= AHCI 1.3") Cc: stable@vger.kernel.org # v4.5+ Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Acked-by:
Andy Gross <andy.gross@linaro.org> Signed-off-by:
-
Srinivas Kandagatla authored
[ Upstream commit 2fd0f46c ] In usecases where force_port_map is used saved_port_map is never set, resulting in not programming the PORTS_IMPL register as part of initial config. This patch fixes this by setting it to port_map even in case where force_port_map is used, making it more inline with other parts of the code. Fixes: 566d1827 ("libata: disable forced PORTS_IMPL for >= AHCI 1.3") Cc: stable@vger.kernel.org # v4.5+ Signed-off-by:
-
Krzysztof Kozlowski authored
[ Upstream commit 3b672623 ] The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff instead of 0x1f) thus reading entire register as buck9's voltage. This effectively caused regulator core to interpret values as higher voltages than they were and then to set real voltage much lower than intended. The buck9 provides power to other regulators, including LDO13 and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower voltage caused SD card detection errors on Odroid XU3/XU4: mmc1: card never left busy state mmc1: error -110 whilst initialising SD card During driver probe the regulator core was checking whether initial voltage matches the constraints. With incorrect vsel_mask of 0xff and default value of 0x50, the core interpreted this as 5 V which is outside of constraints (3-3.775 V). Then the regulator core was adjusting the voltage to match the constraints. With incorrect vsel_mask this new voltage mapped to a vere low voltage in the driver. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Tested-by:
-
Sugar Zhang authored
[ Upstream commit 653aa464 ] this patch corrects the interface adc/dac control register definition according to datasheet. Signed-off-by:
Sugar Zhang <sugar.zhang@rock-chips.com> Signed-off-by:
-
- 13 May, 2016 3 commits
-
-
Sasha Levin authored
[ Upstream commit 9fc515bc ] IWL_INFO is not an error but still printed by default. "can't access the RSA semaphore it is write protected" seems worrisome but it is not really a problem. CC: <stable@vger.kernel.org> [4.1+] Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Sasha Levin authored
I have erroneously created a copy of said file when backporting a commit back to the tree, and have ended up commiting it. Remove it from the tree. Reported-by:
Jens Rottmann <Jens.Rottmann@adlinktech.com> Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit 522dc09c.. Tony writes: This upstream commit is causing an oops: d8f00cd6 ("usb: hub: do not clear BOS field during reset device") This patch has already been included in several -stable kernels. Here are the affected kernels: 4.5.0-rc4 (current git) 4.4.2 4.3.6 (currently in review) 4.1.18 3.18.27 3.14.61 How to reproduce the problem: Boot kernel with slub debugging enabled (otherwise memory corruption will cause random oopses later instead of immediately) Plug in USB 3.0 disk to xhci USB 3.0 port dd if=/dev/sdc of=/dev/null bs=65536 (where /dev/sdc is the USB 3.0 disk) Unplug USB cable while dd is still going Oops is immediate: Reported-by:
Tony Battersby <tonyb@cybernetics.com> Signed-off-by:
-
- 11 May, 2016 1 commit
-
-
Sasha Levin authored
Signed-off-by:
-
- 10 May, 2016 3 commits
-
-
Tony Luck authored
[ Upstream commit ff15e95c ] In commit: eb1af3b7 ("Fix computation of channel address") I switched the "sck_way" variable from holding the log2 value read from the h/w to instead be the actual number. Unfortunately it is needed in log2 form when used to shift the address. Tested-by:
Patrick Geary <patrickg@supermicro.com> Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Jan Beulich authored
[ Upstream commit 103f6112 ] Huge pages are not normally available to PV guests. Not suppressing hugetlbfs use results in an endless loop of page faults when user mode code tries to access a hugetlbfs mapped area (since the hypervisor denies such PTEs to be created, but error indications can't be propagated out of xen_set_pte_at(), just like for various of its siblings), and - once killed in an oops like this: kernel BUG at .../fs/hugetlbfs/inode.c:428! invalid opcode: 0000 [#1] SMP ... RIP: e030:[<ffffffff811c333b>] [<ffffffff811c333b>] remove_inode_hugepages+0x25b/0x320 ... Call Trace: [<ffffffff811c3415>] hugetlbfs_evict_inode+0x15/0x40 [<ffffffff81167b3d>] evict+0xbd/0x1b0 [<ffffffff8116514a>] __dentry_kill+0x19a/0x1f0 [<ffffffff81165b0e>] dput+0x1fe/0x220 [<ffffffff81150535>] __fput+0x155/0x200 [<ffffffff81079fc0>] task_work_run+0x60/0xa0 [<ffffffff81063510>] do_exit+0x160/0x400 [<ffffffff810637eb>] do_group_exit+0x3b/0xa0 [<ffffffff8106e8bd>] get_signal+0x1ed/0x470 [<ffffffff8100f854>] do_signal+0x14/0x110 [<ffffffff810030e9>] prepare_exit_to_usermode+0xe9/0xf0 [<ffffffff814178a5>] retint_user+0x8/0x13 This is CVE-2016-3961 / XSA-174. Reported-by:
Jan Beulich <jbeulich@suse.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Juergen Gross <JGross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luis R. Rodriguez <mcgrof@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Cc: stable@vger.kernel.org Cc: xen-devel <xen-devel@lists.xenproject.org> Link: http://lkml.kernel.org/r/57188ED802000078000E431C@prv-mh.provo.novell.comSigned-off-by:
-
Dominik Dingel authored
[ Upstream commit 7f9be775 ] On s390 we only can enable hugepages if the underlying hardware/hypervisor also does support this. Common code now would assume this to be signaled by setting HPAGE_SHIFT to 0. But on s390, where we only support one hugepage size, there is a link between HPAGE_SHIFT and pageblock_order. So instead of setting HPAGE_SHIFT to 0, we will implement the check for the hardware capability. Signed-off-by:
Dominik Dingel <dingel@linux.vnet.ibm.com> Acked-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by:
-
