Each allocated buffer, whose pointer is put into BM pool is DMA-mapped.
Hence it should be properly unmapped after usage or when removing buffers
from pool.

This commit fixes DMA handling on RX path by adding dma_unmap_single() in
mvpp2_rx() and in mvpp2_bufs_free(). The latter function's argument number
had to be increased for this purpose.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375
network unit")

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>

The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This condition is true only for the last fragment of the packet.

Since every descriptor's buffer is DMA-mapped it has to be properly
unmapped.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375
network unit")

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>

Thomas and Phil observed that under stress rhashtable insertion
sometimes failed with EBUSY, even though this error should only
ever been seen when we're under attack and our hash chain length
has grown to an unacceptable level, even after a rehash.

It turns out that the logic for detecting whether there is an
existing rehash is faulty.  In particular, when two threads both
try to grow the same table at the same time, one of them may see
the newly grown table and thus erroneously conclude that it had
been rehashed.  This is what leads to the EBUSY error.

This patch fixes this by remembering the current last table we
used during insertion so that rhashtable_insert_rehash can detect
when another thread has also done a resize/rehash.  When this is
detected we will give up our resize/rehash and simply retry the
insertion with the new table.
Reported-by: Thomas Graf <tgraf@suug.ch>
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:
 "A lot of Thanksgiving turkey leftovers accumulated, here goes:

   1) Fix bluetooth l2cap_chan object leak, from Johan Hedberg.

   2) IDs for some new iwlwifi chips, from Oren Givon.

   3) Fix rtlwifi lockups on boot, from Larry Finger.

   4) Fix memory leak in fm10k, from Stephen Hemminger.

   5) We have a route leak in the ipv6 tunnel infrastructure, fix from
      Paolo Abeni.

   6) Fix buffer pointer handling in arm64 bpf JIT,f rom Zi Shen Lim.

   7) Wrong lockdep annotations in tcp md5 support, fix from Eric
      Dumazet.

   8) Work around some middle boxes which prevent proper handling of TCP
      Fast Open, from Yuchung Cheng.

   9) TCP repair can do huge kmalloc() requests, build paged SKBs
      instead.  From Eric Dumazet.

  10) Fix msg_controllen overflow in scm_detach_fds, from Daniel
      Borkmann.

  11) Fix device leaks on ipmr table destruction in ipv4 and ipv6, from
      Nikolay Aleksandrov.

  12) Fix use after free in epoll with AF_UNIX sockets, from Rainer
      Weikusat.

  13) Fix double free in VRF code, from Nikolay Aleksandrov.

  14) Fix skb leaks on socket receive queue in tipc, from Ying Xue.

  15) Fix ifup/ifdown crach in xgene driver, from Iyappan Subramanian.

  16) Fix clearing of persistent array maps in bpf, from Daniel
      Borkmann.

  17) In TCP, for the cross-SYN case, we don't initialize tp->copied_seq
      early enough.  From Eric Dumazet.

  18) Fix out of bounds accesses in bpf array implementation when
      updating elements, from Daniel Borkmann.

  19) Fill gaps in RCU protection of np->opt in ipv6 stack, from Eric
      Dumazet.

  20) When dumping proxy neigh entries, we have to accomodate NULL
      device pointers properly, from Konstantin Khlebnikov.

  21) SCTP doesn't release all ipv6 socket resources properly, fix from
      Eric Dumazet.

  22) Prevent underflows of sch->q.qlen for multiqueue packet
      schedulers, also from Eric Dumazet.

  23) Fix MAC and unicast list handling in bnxt_en driver, from Jeffrey
      Huang and Michael Chan.

  24) Don't actively scan radar channels, from Antonio Quartulli"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (110 commits)
  net: phy: reset only targeted phy
  bnxt_en: Setup uc_list mac filters after resetting the chip.
  bnxt_en: enforce proper storing of MAC address
  bnxt_en: Fixed incorrect implementation of ndo_set_mac_address
  net: lpc_eth: remove irq > NR_IRQS check from probe()
  net_sched: fix qdisc_tree_decrease_qlen() races
  openvswitch: fix hangup on vxlan/gre/geneve device deletion
  ipv4: igmp: Allow removing groups from a removed interface
  ipv6: sctp: implement sctp_v6_destroy_sock()
  arm64: bpf: add 'store immediate' instruction
  ipv6: kill sk_dst_lock
  ipv6: sctp: add rcu protection around np->opt
  net/neighbour: fix crash at dumping device-agnostic proxy entries
  sctp: use GFP_USER for user-controlled kmalloc
  sctp: convert sack_needed and sack_generation to bits
  ipv6: add complete rcu protection around np->opt
  bpf: fix allocation warnings in bpf maps and integer overflow
  mvebu: dts: enable IP checksum with jumbo frames for Armada 38x on Port0
  net: mvneta: enable setting custom TX IP checksum limit
  net: mvneta: fix error path for building skb
  ...

Pull block fixes from Jens Axboe:
 "A collection of fixes from this series.  The most important here is a
  regression fix for an issue that some folks would hit in blk-merge.c,
  and the NVMe queue depth limit for the screwed up Apple "nvme"
  controller.

  In more detail, this pull request contains:

   - a set of fixes for null_blk, including a fix for a few corner cases
     where we could hang the device.  From Arianna and Paolo.

   - lightnvm:
        - A build improvement from Keith.
        - Update the qemu pci id detection from Matias.
        - Error handling fixes for leaks and other little fixes from
          Sudip and Wenwei.

   - fix from Eric where BLKRRPART would not return EBUSY for whole
     device mounts, only when partitions were mounted.

   - fix from Jan Kara, where EOF O_DIRECT reads would return
     negatively.

   - remove check for rq_mergeable() when checking limits for cloned
     requests.  The check doesn't make any sense.  It's assuming that
     since NOMERGE is set on the request that we don't have to
     recalculate limits since the request didn't change, but that's not
     true if the request has been redirected.  From Hannes.

   - correctly get the bio front segment value set for single segment
     bio's, fixing a BUG() in blk-merge.  From Ming"

* 'for-linus' of git://git.kernel.dk/linux-block:
  nvme: temporary fix for Apple controller reset
  null_blk: change type of completion_nsec to unsigned long
  null_blk: guarantee device restart in all irq modes
  null_blk: set a separate timer for each command
  blk-merge: fix computing bio->bi_seg_front_size in case of single segment
  direct-io: Fix negative return from dio read beyond eof
  block: Always check queue limits for cloned requests
  lightnvm: missing nvm_lock acquire
  lightnvm: unconverted ppa returned in get_bb_tbl
  lightnvm: refactor and change vendor id for qemu
  lightnvm: do device max sectors boundary check first
  lightnvm: fix ioctl memory leaks
  lightnvm: free memory when gennvm register fails
  lightnvm: Simplify config when disabled
  Return EBUSY from BLKRRPART for mounted whole-dev fs

Pull tracing fix from Steven Rostedt:
 "During the merge window I added a new file that is used to filter
  trace events on pids.  It filters all events where only tasks with
  their pid in that file exists.  It also handles the sched_switch and
  sched_wakeup trace events where the current task does not have its pid
  in the file, but the task either being switched to or awaken does.

  Unfortunately, I forgot about sched_wakeup_new and sched_waking.  Both
  of these tracepoints use the same class as the sched_wakeup
  tracepoint, and they too should be included in what gets filtered by
  the set_event_pid file"

* tag 'trace-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Add sched_wakeup_new and sched_waking tracepoints for pid filter

Merge tag 'mac80211-for-davem-2015-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
A small set of fixes for 4.4:
 * fix scanning in mac80211 to not actively scan radar
   channels (from Antonio)
 * fix uninitialized variable in remain-on-channel that
   could lead to treating frame TX as remain-on-channel
   and not sending the frame at all
 * remove NL80211_FEATURE_FULL_AP_CLIENT_STATE again, it
   was broken and needs more work, we'll enable it later
 * fix call_rcu() induced use-after-reset/free in mesh
   (that was suddenly causing issues in certain tests)
 * always request block-ack window size 64 as we found
   some APs will otherwise crash (really ...)
 * fix P2P-Device teardown sequence to avoid restarting
   with uninitialized data
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: set mac address and uc_list bug fixes.

Fix ndo_set_mac_address() for PF and VF.
Re-apply uc_list after chip reset.

v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters.  Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.

Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW.  For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.

v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existing ndo_set_mac_address only copies the new MAC addr
and didn't set the new MAC addr to the HW. The correct way is
to delete the existing default MAC filter from HW and add
the new one. Because of RFS filters are also dependent on the
default mac filter l2 context, the driver must go thru
close_nic() to delete the default MAC and RFS filters, then
open_nic() to set the default MAC address to HW.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs) and
by default it is set to 16, see arch/arm/include/asm/irq.h.

This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.

Fixes a runtime problem:

    lpc-eth 31060000.ethernet: error getting resources.
    lpc_eth: lpc-eth: not found (-6).
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qdisc_tree_decrease_qlen() suffers from two problems on multiqueue
devices.

One problem is that it updates sch->q.qlen and sch->qstats.drops
on the mq/mqprio root qdisc, while it should not : Daniele
reported underflows errors :
[  681.774821] PAX: sch->q.qlen: 0 n: 1
[  681.774825] PAX: size overflow detected in function qdisc_tree_decrease_qlen net/sched/sch_api.c:769 cicus.693_49 min, count: 72, decl: qlen; num: 0; context: sk_buff_head;
[  681.774954] CPU: 2 PID: 19 Comm: ksoftirqd/2 Tainted: G           O    4.2.6.201511282239-1-grsec #1
[  681.774955] Hardware name: ASUSTeK COMPUTER INC. X302LJ/X302LJ, BIOS X302LJ.202 03/05/2015
[  681.774956]  ffffffffa9a04863 0000000000000000 0000000000000000 ffffffffa990ff7c
[  681.774959]  ffffc90000d3bc38 ffffffffa95d2810 0000000000000007 ffffffffa991002b
[  681.774960]  ffffc90000d3bc68 ffffffffa91a44f4 0000000000000001 0000000000000001
[  681.774962] Call Trace:
[  681.774967]  [<ffffffffa95d2810>] dump_stack+0x4c/0x7f
[  681.774970]  [<ffffffffa91a44f4>] report_size_overflow+0x34/0x50
[  681.774972]  [<ffffffffa94d17e2>] qdisc_tree_decrease_qlen+0x152/0x160
[  681.774976]  [<ffffffffc02694b1>] fq_codel_dequeue+0x7b1/0x820 [sch_fq_codel]
[  681.774978]  [<ffffffffc02680a0>] ? qdisc_peek_dequeued+0xa0/0xa0 [sch_fq_codel]
[  681.774980]  [<ffffffffa94cd92d>] __qdisc_run+0x4d/0x1d0
[  681.774983]  [<ffffffffa949b2b2>] net_tx_action+0xc2/0x160
[  681.774985]  [<ffffffffa90664c1>] __do_softirq+0xf1/0x200
[  681.774987]  [<ffffffffa90665ee>] run_ksoftirqd+0x1e/0x30
[  681.774989]  [<ffffffffa90896b0>] smpboot_thread_fn+0x150/0x260
[  681.774991]  [<ffffffffa9089560>] ? sort_range+0x40/0x40
[  681.774992]  [<ffffffffa9085fe4>] kthread+0xe4/0x100
[  681.774994]  [<ffffffffa9085f00>] ? kthread_worker_fn+0x170/0x170
[  681.774995]  [<ffffffffa95d8d1e>] ret_from_fork+0x3e/0x70

mq/mqprio have their own ways to report qlen/drops by folding stats on
all their queues, with appropriate locking.

A second problem is that qdisc_tree_decrease_qlen() calls qdisc_lookup()
without proper locking : concurrent qdisc updates could corrupt the list
that qdisc_match_from_root() parses to find a qdisc given its handle.

Fix first problem adding a TCQ_F_NOPARENT qdisc flag that
qdisc_tree_decrease_qlen() can use to abort its tree traversal,
as soon as it meets a mq/mqprio qdisc children.

Second problem can be fixed by RCU protection.
Qdisc are already freed after RCU grace period, so qdisc_list_add() and
qdisc_list_del() simply have to use appropriate rcu list variants.

A future patch will add a per struct netdev_queue list anchor, so that
qdisc_tree_decrease_qlen() can have more efficient lookups.
Reported-by: Daniele Fucini <dfucini@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <cwang@twopensource.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each openvswitch tunnel vport (vxlan,gre,geneve) holds a reference
to the underlying tunnel device, but never released it when such
device is deleted.
Deleting the underlying device via the ip tool cause the kernel to
hangup in the netdev_wait_allrefs() loop.
This commit ensure that on device unregistration dp_detach_port_notify()
is called for all vports that hold the device reference, properly
releasing it.

Fixes: 614732ea ("openvswitch: Use regular VXLAN net_device device")
Fixes: b2acd1dc ("openvswitch: Use regular GRE net_device instead of vport")
Fixes: 6b001e68 ("openvswitch: Use Geneve device.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a multicast group is joined on a socket, a struct ip_mc_socklist
is appended to the sockets mc_list containing information about the
joined group.

If the interface is hot unplugged, this entry becomes stale. Prior to
commit 52ad353a ("igmp: fix the problem when mc leave group") it
was possible to remove the stale entry by performing a
IP_DROP_MEMBERSHIP, passing either the old ifindex or ip address on
the interface. However, this fix enforces that the interface must
still exist. Thus with time, the number of stale entries grows, until
sysctl_igmp_max_memberships is reached and then it is not possible to
join and more groups.

The previous patch fixes an issue where a IP_DROP_MEMBERSHIP is
performed without specifying the interface, either by ifindex or ip
address. However here we do supply one of these. So loosen the
restriction on device existence to only apply when the interface has
not been specified. This then restores the ability to clean up the
stale entries.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 52ad353a "(igmp: fix the problem when mc leave group")
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry Vyukov reported a memory leak using IPV6 SCTP sockets.

We need to call inet6_destroy_sock() to properly release
inet6 specific fields.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hedberg says:

====================
pull request: bluetooth 2015-12-01

Here's a Bluetooth fix for the 4.4-rc series that fixes a memory leak of
the Security Manager L2CAP channel that'll happen for every LE
connection.

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

aarch64 doesn't have native store immediate instruction, such operation
has to be implemented by the below instruction sequence:

Load immediate to register
Store register
Signed-off-by: Yang Shi <yang.shi@linaro.org>
CC: Zi Shen Lim <zlim.lnx@gmail.com>
CC: Xi Wang <xi.wang@gmail.com>
Reviewed-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While testing the np->opt RCU conversion, I found that UDP/IPv6 was
using a mixture of xchg() and sk_dst_lock to protect concurrent changes
to sk->sk_dst_cache, leading to possible corruptions and crashes.

ip6_sk_dst_lookup_flow() uses sk_dst_check() anyway, so the simplest
way to fix the mess is to remove sk_dst_lock completely, as we did for
IPv4.

__ip6_dst_store() and ip6_dst_store() share same implementation.

sk_setup_caps() being called with socket lock being held or not,
we have to use sk_dst_set() instead of __sk_dst_set()

Note that I had to move the "np->dst_cookie = rt6_get_cookie(rt);"
in ip6_dst_store() before the sk_setup_caps(sk, dst) call.

This is because ip6_dst_store() can be called from process context,
without any lock held.

As soon as the dst is installed in sk->sk_dst_cache, dst can be freed
from another cpu doing a concurrent ip6_dst_store()

Doing the dst dereference before doing the install is needed to make
sure no use after free would trigger.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch completes the work I did in commit 45f6fad8
("ipv6: add complete rcu protection around np->opt"), as I missed
sctp part.

This simply makes sure np->opt is used with proper RCU locking
and accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Proxy entries could have null pointer to net-device.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Fixes: 84920c14 ("net: Allow ipv6 proxies and arp proxies be shown with iproute2")
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry Vyukov reported that the user could trigger a kernel warning by
using a large len value for getsockopt SCTP_GET_LOCAL_ADDRS, as that
value directly affects the value used as a kmalloc() parameter.

This patch thus switches the allocation flags from all user-controllable
kmalloc size to GFP_USER to put some more restrictions on it and also
disables the warn, as they are not necessary.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

They don't need to be any bigger than that and with this we start a new
bitfield for tracking association runtime stuff, like zero window
situation.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch addresses multiple problems :

UDP/RAW sendmsg() need to get a stable struct ipv6_txoptions
while socket is not locked : Other threads can change np->opt
concurrently. Dmitry posted a syzkaller
(http://github.com/google/syzkaller) program desmonstrating
use-after-free.

Starting with TCP/DCCP lockless listeners, tcp_v6_syn_recv_sock()
and dccp_v6_request_recv_sock() also need to use RCU protection
to dereference np->opt once (before calling ipv6_dup_options())

This patch adds full RCU protection to np->opt
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

For large map->value_size the user space can trigger memory allocation warnings like:
WARNING: CPU: 2 PID: 11122 at mm/page_alloc.c:2989
__alloc_pages_nodemask+0x695/0x14e0()
Call Trace:
 [<     inline     >] __dump_stack lib/dump_stack.c:15
 [<ffffffff82743b56>] dump_stack+0x68/0x92 lib/dump_stack.c:50
 [<ffffffff81244ec9>] warn_slowpath_common+0xd9/0x140 kernel/panic.c:460
 [<ffffffff812450f9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:493
 [<     inline     >] __alloc_pages_slowpath mm/page_alloc.c:2989
 [<ffffffff81554e95>] __alloc_pages_nodemask+0x695/0x14e0 mm/page_alloc.c:3235
 [<ffffffff816188fe>] alloc_pages_current+0xee/0x340 mm/mempolicy.c:2055
 [<     inline     >] alloc_pages include/linux/gfp.h:451
 [<ffffffff81550706>] alloc_kmem_pages+0x16/0xf0 mm/page_alloc.c:3414
 [<ffffffff815a1c89>] kmalloc_order+0x19/0x60 mm/slab_common.c:1007
 [<ffffffff815a1cef>] kmalloc_order_trace+0x1f/0xa0 mm/slab_common.c:1018
 [<     inline     >] kmalloc_large include/linux/slab.h:390
 [<ffffffff81627784>] __kmalloc+0x234/0x250 mm/slub.c:3525
 [<     inline     >] kmalloc include/linux/slab.h:463
 [<     inline     >] map_update_elem kernel/bpf/syscall.c:288
 [<     inline     >] SYSC_bpf kernel/bpf/syscall.c:744

To avoid never succeeding kmalloc with order >= MAX_ORDER check that
elem->value_size and computed elem_size are within limits for both hash and
array type maps.
Also add __GFP_NOWARN to kmalloc(value_size | elem_size) to avoid OOM warnings.
Note kmalloc(key_size) is highly unlikely to trigger OOM, since key_size <= 512,
so keep those kmalloc-s as-is.

Large value_size can cause integer overflows in elem_size and map.pages
formulas, so check for that as well.

Fixes: aaac3ba9 ("bpf: charge user for creation of BPF maps and programs")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marcin Wojtas says:

====================
Marvell Armada XP/370/38X Neta fixes

I'm sending v4 with corrected commit log of the last patch, in order to
avoid possible conflicts between the branches as suggested by Gregory
Clement.

Best regards,
Marcin Wojtas

Changes from v4:
* Correct commit log of patch 6/6

Changes from v2:
* Style fixes in patch updating mbus protection
* Remove redundant stable notifications except for patch 4/6

Changes from v1:
* update MBUS windows access protection register once, after whole loop
* add fixing value of MVNETA_RXQ_INTR_ENABLE_ALL_MASK
* add fixing error path for skb_build()
* add possibility of setting custom TX IP checksum limit in DT property
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The Ethernet controller found in the Armada 38x SoC's family support
TCP/IP checksumming with frame sizes larger than 1600 bytes, however
only on port 0.

This commit enables it by setting 'tx-csum-limit' to 9800B in
'ethernet@70000' node.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since Armada 38x SoC can support IP checksum for jumbo frames only on
a single port, it means that this feature should be enabled per-port,
rather than for the whole SoC.

This patch enables setting custom TX IP checksum limit by adding new
optional property to the mvneta device tree node. If not used, by
default 1600B is set for "marvell,armada-370-neta" and 9800B for other
strings, which ensures backward compatibility. Binding documentation
is updated accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the actual RX processing, there is same error path for both descriptor
ring refilling and building skb fails. This is not correct, because after
successful refill, the ring is already updated with newly allocated
buffer. Then, in case of build_skb() fail, hitherto code left the original
buffer unmapped.

This patch fixes above situation by swapping error check of skb build with
DMA-unmap of original buffer.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # v4.2+
Fixes a84e3289 ("net: mvneta: fix refilling for Rx DMA buffers")
Signed-off-by: David S. Miller <davem@davemloft.net>

A value originally defined in the driver was inappropriate. Even though
the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK
to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16]
are reserved and read-only.

This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with
the controller's documentation.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>

MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer
allocation was mistakenly set as BIT(1). This commit fixes the assignment.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit adds missing configuration of MBUS windows access protection
in mvneta_conf_mbus_windows function - a dedicated variable for that
purpose remained there unused since v3.8 initial mvneta support. Because
of that the register contents were inherited from the bootloader.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull spi fixes from Mark Brown:
 "There's one fix for the core here, we weren't reinitialising the
  actual transferred length in messages when they get reused which meant
  that we'd just keep adding to the length if a message is reused.  This
  has limited impact since it's only used in error handling cases but
  will really mess anything that tries to use it up when it triggers.

  As ever there's a small collection of driver specific fixes too"

* tag 'spi-fix-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: bugfix: spi_message.transfer_length does not get reset
  spi: pl022: handle EPROBE_DEFER for dma
  spi: bcm63xx: use correct format string for printing a resource
  spi: mediatek: single device does not require cs_gpios
  spi: Add missing kerneldoc description for parameter

In the last change here, I neglected to update the cookie in one code
path: when a mgmt-tx has no real cookie sent to userspace as it doesn't
wait for a response, but is off-channel. The original code used the SKB
pointer as the cookie and always assigned the cookie to the TX SKB in
ieee80211_start_roc_work(), but my change turned this around and made
the code rely on a valid cookie being passed in.

Unfortunately, the off-channel no-wait TX path wasn't assigning one at
all, resulting in an uninitialized stack value being used. This wasn't
handed back to userspace as a cookie (since in the no-wait case there
isn't a cookie), but it was tested for non-zero to distinguish between
mgmt-tx and off-channel.

Fix this by assigning a dummy non-zero cookie unconditionally, and get
rid of a misleading comment and some dead code while at it. I'll clean
up the ACK SKB handling separately later.

Fixes: 3b79af97 ("mac80211: stop using pointers as userspace cookies")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

DFS channels should not be actively scanned as we can't be sure
if we are allowed or not.

If the current channel is in the DFS band, active scan might be
performed after CSA, but we have no guarantee about other channels,
therefore it is safer to prevent active scanning at all.

Cc: stable@vger.kernel.org
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Interfaces are being initialized (setup) on addition,
and torn down on removal.

However, p2p device is being torn down when stopped,
resulting in the next p2p start operation being done
on uninitialized interface.

Solve it by calling ieee80211_teardown_sdata() only
on interface removal (for the non-netdev case).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[squashed in fix to call teardown after unregister]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Sunil Goutham says:

====================
thunderx: miscellaneous fixes

This patch series contains fixes for various issues observed
with BGX and NIC drivers.

Changes from v1:
- Fixed comment syle in the first patch of the series
- Removed 'Increase transmit queue length' patch from the series,
  will recheck if it's a driver or system issue and resubmit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable or disable BGX LMAC's RX/TX based on corresponding VF's
status. If otherwise, when multiple LMAC's physical link is up
then packets from all LMAC's whose corresponding VF is not yet
initialized will get forwarded to VF0. This is due to VNIC's default
configuration where CPI, RSSI e.t.c point to VF0/QSET0/RQ0.

This patch will prevent multiple copies of packets on VF0.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call netif_carrier_on() only if interface's link is up. Switching this on
upon IFF_UP by default, is causing issues with ethernet channel bonding
in LACP mode. Initial NETDEV_CHANGE notification was being skipped.

Also fixed some issues with link/speed/duplex reporting via ethtool.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>