- 25 Apr, 2012 18 commits
-
-
K. Y. Srinivasan authored
Hyper-V cannot process some commands like ATA_12 and ATA_16. It also returns a very generic error when this happens (SRB_STATUS_ERROR). Most of the time we treat SRB_STATUS_ERROR as DID_TARGET_FAILURE which causes error handler retry, but in the case of pass through commands, they'll never succeed (and the error handler will offline the device), so put a discriminating block in the command completion routing and send the SRB_STATUS_ERROR upwards with DID_PASSTHROUGH for commands we know should not be retried. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Reviewed-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
John Soni Jose authored
Implement ISCSI_HOST_PARAM_PORT_STATE and ISCSI_HOST_PARAM_PORT_SPEED to get the Adapter port state and port name Signed-off-by:
John Soni Jose <sony.john-n@emulex.com> Signed-off-by:
Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Mike Christie authored
This patch allows iscsiadm to set/ delete static IP and enable /disable DHCP. Signed-off-by:
-
Jayamohan Kallickal authored
Signed-off-by:
-
John Soni Jose authored
Implement the ISCSI_HOST_PARAM_INITIATOR_NAME for .get_host_param Signed-off-by:
-
Jayamohan Kallickal authored
The async handle corresponding to unknown Opcode was not freed earlier. This code does the fix for that. Signed-off-by:
-
Jayamohan Kallickal authored
For each ASYNC PDU received there is an HDR and DATA handle for it. There will be only 1 HDR ASYNC Handle, but DATA Handle can be more than 1 for each ASYNC PDU received. Checking if the ASYNC Handle correspongs to HDR or DATA while returning the Handle to the free list. hwi_free_async_msg just return the handles to the free list. No return values are needed so changing the return type to void. Signed-off-by:
-
Jayamohan Kallickal authored
Signed-off-by:
Minh Tran <MinhDuc.Tran@Emulex.Com> Signed-off-by:
-
Jayamohan Kallickal authored
Change MODULE_AUTHOR, driver name and other external print strings from Serverengines to Emulex. Signed-off-by:
-
Jayamohan Kallickal authored
Signed-off-by:
-
Jayamohan Kallickal authored
Signed-off-by:
-
Jayamohan Kallickal authored
In case of MCC_Q creation failed, the MCCQ info memory is freed from be_mcc_queues_destroy and be_mcc_queues_create. This caused kernel to panic because of double free. Signed-off-by:
-
Jayamohan Kallickal authored
Signed-off-by:
-
Jayamohan Kallickal authored
Signed-off-by:
-
Mike Christie authored
The WRB and SGL Handle allocated for Login task were not freed back to the pool after the login process was done. This code releases the WRB and SGL Handle after the login process. v2: - Fix up locking so bh calls are not done when not needed. - Make beiscsi_cleanup_task static. Signed-off-by:
-
Jayamohan Kallickal authored
Removing code duplication during the WRB_Handle and WRB initialization. Added memory allocation failure handling code during WRB initialization. Signed-off-by:
-
Jayamohan Kallickal authored
The buffer length passed for processing the ASYNC PDU was not proper. Signed-off-by:
-
Jayamohan Kallickal authored
Set the ASYNC PDU Handle pBuffer for Data ring with the VA/PA of the allocated memory for it. To get the correct ASYNC PDY Handle iterate the list and compare the PA set during initialization with the passed PHY Address. The buffer_size and num_enteries are common for HDR and Data ring Signed-off-by:
-
- 23 Apr, 2012 22 commits
-
-
Akinobu Mita authored
Use check_signature to find a signature in the mmio address. Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Acked-by:
Mike Miller <mike.miller@hp.com> Signed-off-by:
-
Tomas Henzl authored
The patch 11604612 "[SCSI] aacraid: Added Sync.mode to support series 7/8/9 controllers" removed an iounmap call from aac_src_ioremap. Before that, the iounmap has been called twice with the same value (dev->base and dev->regs.src.bar0) and the iounmap complained about it (iounmap: bad address ...). The proper solution is a change the paremeter from bar0 to bar1. Fix this by adding a an iounmap(dev->regs.src.bar1) call. Signed-off-by:
Tomas Henzl <thenzl@redhat.com> Acked-by:
Achim Leubner <achim_leubner@pmc-sierra.com> Signed-off-by:
-
Moger, Babu authored
This patch optimizes the set target port group(STPG) command. During our testing, we found that it is not optimal to send stpg command every time the path group switch happens. This patch uses PREF (preferred target port) bit with combination of flags passed by multipath user level tool to optimize this behaviour. If PREF bit is set then it issues a STPG command, otherwise it will let implicit transfer take place. By default there is no change in the behaviour. User tool needs to pass the parameter to make this change take effect. Patch has been tested on NetApp E series storage. Signed-off-by:
Babu Moger <babu.moger@netapp.com> Reviewed-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Moger, Babu authored
PREF bit indicates preferred target port group for accessing a logical unit. This bit is used to optimize the STPG command handling. Signed-off-by:
-
Moger, Babu authored
Handler expects only one parameter to set the flag ALUA_OPTIMIZE_STPG. This flag is used to optimize the STPG behaviour. There is no change in behaviour by default. For example, to set the flag pass the following parameters from multipath.conf hardware_handler "2 alua 1" Signed-off-by:
-
Roland Dreier authored
Signed-off-by:
Roland Dreier <roland@purestorage.com> Reviewed-by:
-
nagalakshmi.nandigama@lsi.com authored
Signed-off-by:
Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com> Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
The ioc->pfacts member in the IOC structure is getting set to zero following a call to _base_get_ioc_facts due to the memset in that routine. So if the ioc->pfacts was read after a host reset, there would be a NULL pointer dereference. The routine _base_get_ioc_facts is called from context of host reset. The problem in _base_get_ioc_facts is the size of Mpi2IOCFactsReply is 64, whereas the sizeof "struct mpt2sas_facts" is 60, so there is a four byte overflow resulting from the memset. Also, there is memset in _base_get_port_facts using the incorrect structure, it should be "struct mpt2sas_port_facts" instead of Mpi2PortFactsReply. Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
[SCSI] mpt2sas: Fix for hard drive going OFFLINE when hard reset issued and simultaneously another hard drive is hot unplugged Following the host reset, the firmware discovery is reassigning another hard drive in the topology to the same device handle as that device is getting hot removed. Until the driver device removal routine is called, there will be two hard drive with the matching device handle in the internal device link list. In the device removal routine, a separate function which moves the device from BLOCKED into OFFLINE state. Since this routine is passed with the device handle passed as input parameter, the routine will be traversing the internal device link list searching for matching device handle. This results in two devices with matching device handle, therefore both devices goes OFFLINE. To fix this issue,the input parameter is changed from device handle to SAS address, therefore only the device that is hot unplugged will be placed in OFFLINE state. Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
[SCSI] mpt2sas: Set the phy identifier of the end device to the phy number of the parent device it is linked to The phy_identifier inside the routine _transport_set_identify() is set to sas_device_page_zero->PhyNum. This returns the phy number of the parent device this device is linked to. Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
[SCSI] mpt2sas : While enabling phy, read the current port number from sas iounit page 0 instead of page 1 The port number is changing after disabling/enabling phys using the SysFS interface This is because the firmware behavour changed where it would read the the port number then set it to some different value even though Auto Port Config is turned on. With this change of behavour in FW, it is possible that the expanders are moved from one port to another after disabling /enabling phys. This is occuring because the port number in sas iounit page 1 is not matching up to the current port in page 0. In order to fix this the driver is modified to read the current port number from sas iounit page 0 instead of page 1. Also copy the port and phy flags over from page 0 to page 1. Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
Fix several endian issues found by runing sparse. Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
Modified the source code as per the findings reported by the source code analysis tool. Source code for the following functionalities has been touched. None of the driver functionalities has changed. - SMP Passthrough IOCTL - Debug messages for MPT Replies (i.e. bit 9 of Logging Level) - Task Management using sysfs - Device removal, i.e. when a target device (including any PD within a volume) is removed, and Volume Deletion. - Trace Buffer Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
[SCSI] mpt2sas: Improvement were made to better protect the sas_device, raid_device, and expander_device lists There were possible race conditions surrounding reading an object from the link list while from another context in the driver was removing it. The nature of this enhancement is to rearrange locking so the link lists are better protected. Change set: (1) numerous routines were rearranged so spin locks are held through the entire time a link list object is being read from or written to. (2) added new routines for object deletion from link list. Thus ensuring lock was held during the deletion of the link list object, then and memory for object freed outside the lock. The memory was freed outside the lock so driver had access to device object info which was required for notifying the scsi mid layer that a device was getting deleted. (3) added the ioc->blocking_handles parameter. This is a bitmask used to identify which devices need blocking when there is device loss. This was introduced so that lock can be held for the entire time traversing the link list objects, and the bitmask was set to indicate which device handles need blocking. Oustide the lock the ioc->blocking_handles bitmask is traversed, with the respective device handle the scsi mid layer is called for moving devices into blocking state. Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
[SCSI] mpt2sas : Perform Target Reset instead of HBA reset when a SATA_PASSTHROUGH cmd timeout happens Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
Added support for Block IO requests with multiple segments (vectors) in the SMP handler of the SAS Transport Class. This is required by the BSG driver. Multisegment support added for both, Request and Response. Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
When the lock_kernel and unlock_kernel routines were removed in the 2.6.39 kernel, a global mutex was added on top of the existing mutex which already existed. With this implementation, only one IOCTL will be active at any time no matter how many ever controllers are present. This causes poor performance. Removed the global mutex so that the driver can work with the existing semaphore that was already part of the existing code. Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
Changeset in MPI headers: 1) Bumped MPI2_HEADER_VERSION_UNIT 2) Added 4K sectors supported bit to CapabilitiesFlags field of IOC Page 6. 3) Added UEFIVersion field to BIOS Page 1 and defined additional BiosOptions bits to control UEFI behavior. Signed-off-by: -
adam radford authored
The following patch for megaraid_sas updates the driver version to v00.00.06.15-rc1, and updates Documentation/scsi/ChangeLog.megaraid_sas. Signed-off-by:
Adam Radford <aradford@gmail.com> Signed-off-by:
-
adam radford authored
The following patch for megaraid_sas fixes the fastpath code decision logic to use fpRead/WriteCapable, fpRead/WriteAcrossStripe flags instead of the old logic. This fixes a bug where fastpath writes could be sent to a read only LD. Signed-off-by:
-
adam radford authored
The following patch for megaraid_sas removes an incorrect comment and optimizes the setting of HostMSIxVectors. This was found during a code review by Tomas Henzl @ RedHat. Signed-off-by:
-
Santosh Nayak authored
Data type of the 'tag' field of 'fw_flash_Update_resp' should be __le32. Data type of 'pHeader' should be __le32. Remove 2nd cast to 'piomb'. Signed-off-by:
Santosh Nayak <santoshprasadnayak@gmail.com> Acked-by:
Jack Wang <jack_wang@usish.com> Signed-off-by:
-
