- 28 Apr, 2007 34 commits
-
-
Alan Cox authored
This alone isn't sufficient to save the universe from prehistoric disks and controllers but it is a first important step. Split off a separate function to provide a mode filter when controller iordy is not available. Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
Jeff Garzik <jeff@garzik.org>
-
Alan authored
This splits set_mode into do_set_mode and the wrapper so that a driver can call the standard method inside its own. This in theory also obsoletes ->post_set_mode(). Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Alan Cox authored
Drag pata_hpt37x kicking and screaming in the direction of drivers/ide/pci/hpt366.c and all the work that Sergei has been doing there. Plenty left to be done but this is a good snapshot for folks to work on and to review Signed-off-by:
-
Tejun Heo authored
Implement pcim_iounmap_regions() - the opposite of pcim_iomap_regions(). Signed-off-by:
Tejun heo <htejun@gmail.com> Signed-off-by:
-
Jeff Garzik authored
Roll-up of ->cable_detect feature addition patches, authored and signed-off-by Alan Cox. Signed-off-by: -
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Signed-off-by:
Alan Cox <number6@the-village.bc.nu> Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Fix suspend/resume support Write 0x5B to 0 not 0x5C The former is important as we must kill the FIFO on a resume Signed-off-by:
-
Alan Cox authored
We end up shifting a few bits of logic around in this driver but the basic change is the same. Signed-off-by:
-
Alan Cox authored
This changeset revolves around the fact that all the SiS controllers have the same enable bits, but differing cable detection methods. Previously that meant each type had its own error_handler methods. Instead we can now implement different ->cable_detect methods and share a single error_handler which does the filtering by enable bits. In addition we had some auto const arrays that should be static const. I'm not sure if gcc already treats them intelligently but adding the static will make sure. Signed-off-by:
-
Alan Cox authored
There are two changes here. Firstly we switch to a cable detect method, secondly the old code forgot to call ata_std_prereset() but somehow managed to work anyway. Fix the missing call. Signed-off-by:
-
Alan Cox authored
Another not-quite PIIX, another cable type conversion Signed-off-by:
-
Jeff Garzik authored
All patches authored and signed-off-by Alan Cox, sent on Mar 7, 2007. I merely combined them all into a single patch. Signed-off-by: -
Morrison, Tom authored
Added Support for Marvell 7042 Chip - 7042 has same capabilities & behavior as 6042. Signed-off-by:
Thomas A. Morrison <tmorrison@empirix.com> Signed-off-by:
-
Alan Cox authored
Support for the PCI CMD640 (not VLB) Signed-off-by:
-
Alan Cox authored
2.6.21-rc has horrible problems with libata and PATA cable types (and thus speeds). This occurs because Tejun fixed a pile of other bugs and we now do cable detect enforcement for drive side detection properly. Unfortunately we don't do the process around cable detection right. Tejun identified the problem and pointed to the right Annex in the spec, this patch implements the rest of the needed changes. We add a ->cable_detect() method called after the identify sequence which allows a host to do host side detection at this point should it wish, or to modify the results of the drive side identify. This separate ->cable_detect method also cleans up a lot of code because many drivers have their own error_handler methods which really just set the cable type. If there is no ->cable_detect method the cable type is left alone so a driver setting it earlier (eg because it has the SATA flags set or because it uses the old error_handler approach) will still do the right thing (or at least the same thing) as before. This patch simply adds the cable_detect method and helpers it doesn't use them but other follow up patches will (ie Adrian please don't submit patches to unexport them ;)) Signed-off-by:
-
Dmitriy Monakhov authored
Since commit:553c4aa6 ata_pci_device_do_resume() can return error code, all callers was updated except this one. Signed-off-by:
Monakhov Dmitriy <dmonakhov@openvz.org> Signed-off-by:
-
Robert Hancock authored
Warn the user if a drive's transfer rate is limited because of a 40-wire cable detection. Signed-off-by:
Robert Hancock <hancockr@shaw.ca> Cc: Jeff Garzik <jeff@garzik.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by:
-
Mark Lord authored
Resending, with s/printk/DPRINTK/ as pointed out by Alan. Fix libata to perform CDB len validation per device rather than per host. This way, validation still works when we have a mix of 12-byte and 16-byte devices on a common host interface. Signed-off-by:
Mark Lord <mlord@pobox.com> Signed-off-by:
-
Alan authored
It used to be impossible to get from ata_device to ata_port but that is no longer true. Various methods have been cleaned up over time but dev_config still takes both and most users don't need both anyway. Tidy this one up Signed-off-by:
-
Jeff Garzik authored
The chips covered by sata_mv have a 32-bit DMA boundary they must not cross, not a 64K boundary. We are merely limited to a 64K maximum segment size. Therefore, the DMA scatter/gather table fill code can be greatly simplified, and we need not cut in half the S/G table size as reported to the SCSI layer. Also, the driver forget to turn on 64-bit DMA at the PCI layer. All other data structures (both hardware and software) have been prepped for 64-bit PCI DMA. It was simply never turned on. <fingers crossed> let's see if it still works... Signed-off-by: -
Jeff Garzik authored
To be used in sata_mv's exception handling code, and overall is a generally useful function. Signed-off-by: -
Jeff Garzik authored
Signed-off-by: -
Linus Torvalds authored
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: sis900: Allocate rx replacement buffer before rx operation usb-net/pegasus: simplify carrier detection
-
Neil Horman authored
Just found a hole in my last patch. It was reported to me that shortly after we integrated this patch. The report was of an oops that took place inside of netif_rx when using the sis900 driver. Looking at my origional patch I noted that there was a spot between the new skb_alloc and the refill_rx_ring label where skb got reassigned to the pointer currently held in the rx_ring for the purposes of receiveing the frame. The result of this is however that the buffer that gets passed to netif_rx (if it is called), then gets placed right back into the rx_ring. So if you receive frames fast enough the skb being processed by the network stack can get corrupted. The reporter is testing out the fix I've written for this below (I'm not near my hardware at the moment to test myself), but I wanted to post it for review ASAP. I'll post test results when I hear them, but I think this is a pretty straightforward fix. It just uses a separate pointer to do the rx operation, so that we don't improperly reassign the pointer that we use to refill the rx ring. Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Dan Williams authored
Simplify pegasus carrier detection; rely only on the periodic MII polling. Reverts pieces of c43c49bd. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
- 27 Apr, 2007 6 commits
-
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: [SCSI] esp_scsi.c: Fix compilation.
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [NET]: Fix networking compilation errors [AF_RXRPC/AFS]: Arch-specific fixes. [AFS]: Fix VLocation record update wakeup [NET]: Revert sk_buff walker cleanups.
-
git://git.infradead.org/mtd-2.6Linus Torvalds authored
* git://git.infradead.org/mtd-2.6: (46 commits) [MTD] [MAPS] drivers/mtd/maps/ck804xrom.c: convert pci_module_init() [MTD] [NAND] CM-x270 MTD driver [MTD] [NAND] Wrong calculation of page number in nand_block_bad() [MTD] [MAPS] fix plat-ram printk format [JFFS2] Fix compr_rubin.c build after include file elimination. [JFFS2] Handle inodes with only a single metadata node with non-zero isize [JFFS2] Tidy up licensing/copyright boilerplate. [MTD] [OneNAND] Exit loop only when column start with 0 [MTD] [OneNAND] Fix access the past of the real oobfree array [MTD] [OneNAND] Update Samsung OneNAND official URL [JFFS2] Better fix for all-zero node headers [JFFS2] Improve read_inode memory usage, v2. [JFFS2] Improve failure mode if inode checking leaves unchecked space. [JFFS2] Fix cross-endian build. [MTD] Finish conversion mtd_blkdevs to use the kthread API [JFFS2] Obsolete dirent nodes immediately on unlink, where possible. Use menuconfig objects: MTD [MTD] mtd_blkdevs: Convert to use the kthread API [MTD] Fix fwh_lock locking [JFFS2] Speed up mount for directly-mapped NOR flash ...
-
Adrian Bunk authored
This patch converts the pci_module_init() usage to pci_register_driver(). It's currently #if 0'ed, but still not a bad idea to change it. Signed-off-by:
Adrian Bunk <bunk@stusta.de> Signed-off-by:
David Woodhouse <dwmw2@infradead.org>
-
David Howells authored
Fix miscellaneous networking compilation errors. (*) Export ktime_add_ns() for modules. (*) wext_proc_init() should have an ANSI declaration. Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David Howells authored
Fixes for various arch compilation problems: (*) Missing module exports. (*) Variable name collision when rxkad and af_rxrpc both built in (rxrpc_debug). (*) Large constant representation problem (AFS_UUID_TO_UNIX_TIME). (*) Configuration dependencies. (*) printk() format warnings. Signed-off-by:
-
