Use the at91sam9x5 display module dtsi in the relevant board dts.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

All the at91sam9x5-ek share the share display module, add a dtsi to
describe it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Actually make use of at91sam9x5_lcd.dtsi in the relevant SoC dtsis.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Define at91sam9x5 hlcdc node for the SoCs with an LCD controller.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The watchdog, the reset controller, the RTC, the shutdown controller, the
timer counters and the LCD PWM need the slow clock, add it where necessary.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The watchdog, the reset controller, the RTC, the shutdown controller, the
timer counters and the LCD PWM need the slow clock, add it where necessary.

[boris.brezillon@free-electrons.com: add tcb clocks]
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The watchdog, the reset controller, the RTC, the shutdown controller, the
timer counters and the LCD PWM need the slow clock, add it where necessary,
The LCD PWM will be handled later.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The watchdog, the reset controller, the RTC, the real-time timer, the
shutdown controller and the timer counter need the slow clock, add it where
necessary.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The watchdog, the reset controller, the RTC, the shutdown controller, the
timer counters and the LCD PWM need the slow clock, add it where necessary.
The LCD PWM will be handled later.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The watchdog, the reset controller, the RTC, the real-time timer, the
shutdown controller and the timer counters need the slow clock, add it
where necessary.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The watchdog, the reset controller, the two real-time timers, the shutdown
controller and the timer counter need the slow clock, add it where
necessary.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The watchdog, the reset controller, the real-time timer, the shutdown
controller and the timer counter need the slow clock, add it where
necessary.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The watchdog, the reset controller, the real-time timer, the shutdown
controller, the timer counters need the slow clock, add it where necessary.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The system timer, the RTC and the timer counters need the slow clock, add
it.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The RTC needs an input clock, it is the slow clock. It is required as it
will not function without it.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The watchdog has an input clock, the slow clock. It is required as it will
not function without it.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The timer counters need the slow clock. It is required as they
will not function without it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The system timer (at91rm9200), the reset controller and the shutdown
controller need an input clock. This is the slow clock and they will not
function without it.

Also fix the shutdown controller example.
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add minimal support for the new sama5d2 Xplained board. Only USB,
spi/i2c, ethernet and uart/usart peripherals added.
With this DTS file you can boot the board and begin to play with it.
Rootfs on NFS and sd card have successfully been tested.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Only the basic support for this new Atmel Cortex-A5 SoC. A subset of the
peripherals is setup to allow booting.
IRQ, clocks, USB, crypto, timers, rtc, ethernet, spi/i2c and
uart/usart peripheral nodes are added.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

They'll use "atmel,sama5d3-rstc" for reset function.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: add the old compatible string as a fallback]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

First we group the isi data pins, and for now we only use 0~7 data pins
with HSYNC and VSYNC.
Also add the link for atmel-isi and ov2640 sensor node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[nicolas.ferre@atmel.com: move the pinctrl properties in board .dts file]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The ADC pinctrl is board specific, move it to the board device trees.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The property is actually atmel,adc-use-external-triggers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This reverts commit dec4f799.

Jörg Otte reports a NULL pointder dereference due to this commit, as
'crtc_state' very much can be NULL:

        crtc_state = state->base.state ?
                intel_atomic_get_crtc_state(state->base.state, intel_crtc) : NULL;

So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.

There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull VFS fixes from Al Viro:
 "Fixes for this cycle regression in overlayfs and a couple of
  long-standing (== all the way back to 2.6.12, at least) bugs"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  freeing unlinked file indefinitely delayed
  fix a braino in ovl_d_select_inode()
  9p: don't leave a half-initialized inode sitting around

Pull MIPS fixes from Ralf Baechle:
 "A fair number of 4.2 fixes also because Markos opened the flood gates.

   - Patch up the math used calculate the location for the page bitmap.

   - The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ
     around was causing issues on non-Malta platforms, so move the code
     to a Malta specific location.

   - A spelling fix replicated through several files.

   - Fix to the emulation of an R2 instruction for R6 cores.

   - Fix the JR emulation for R6.

   - Further patching of mindless 64 bit issues.

   - Ensure the kernel won't crash on CPUs with L2 caches with >= 8
     ways.

   - Use compat_sys_getsockopt for O32 ABI on 64 bit kernels.

   - Fix cache flushing for multithreaded cores.

   - A build fix"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: O32: Use compat_sys_getsockopt.
  MIPS: c-r4k: Extend way_string array
  MIPS: Pistachio: Support CDMM & Fast Debug Channel
  MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
  MIPS: c-r4k: Fix cache flushing for MT cores
  Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
  MIPS: cps-vec: Use macros for various arithmetics and memory operations
  MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0
  MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit
  MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2
  MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA
  MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting
  MIPS: Fix erroneous JR emulation for MIPS R6
  MIPS: Fix branch emulation for BLTC and BGEC instructions
  MIPS: kernel: traps: Fix broken indentation
  MIPS: bootmem: Don't use memory holes for page bitmap
  MIPS: O32: Do not handle require 32 bytes from the stack to be readable.
  MIPS, CPUFREQ: Fix spelling of Institute.
  MIPS: Lemote 2F: Fix build caused by recent mass rename.

Pull x86 fixes from Thomas Gleixner:

 - the high latency PIT detection fix, which slipped through the cracks
   for rc1

 - a regression fix for the early printk mechanism

 - the x86 part to plug irq/vector related hotplug races

 - move the allocation of the espfix pages on cpu hotplug to non atomic
   context.  The current code triggers a might_sleep() warning.

 - a series of KASAN fixes addressing boot crashes and usability

 - a trivial typo fix for Kconfig help text

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text
  x86/irq: Retrieve irq data after locking irq_desc
  x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable()
  x86/irq: Plug irq vector hotplug race
  x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8'
  x86/espfix: Init espfix on the boot CPU side
  x86/espfix: Add 'cpu' parameter to init_espfix_ap()
  x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig
  x86/kasan: Add message about KASAN being initialized
  x86/kasan: Fix boot crash on AMD processors
  x86/kasan: Flush TLBs after switching CR3
  x86/kasan: Fix KASAN shadow region page tables
  x86/init: Clear 'init_level4_pgt' earlier
  x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()

Pull timer fixes from Thomas Gleixner:
 "This update from the timer departement contains:

   - A series of patches which address a shortcoming in the tick
     broadcast code.

     If the broadcast device is not available or an hrtimer emulated
     broadcast device, some of the original assumptions lead to boot
     failures.  I rather plugged all of the corner cases instead of only
     addressing the issue reported, so the change got a little larger.

     Has been extensivly tested on x86 and arm.

   - Get rid of the last holdouts using do_posix_clock_monotonic_gettime()

   - A regression fix for the imx clocksource driver

   - An update to the new state callbacks mechanism for clockevents.
     This is required to simplify the conversion, which will take place
     in 4.3"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/broadcast: Prevent NULL pointer dereference
  time: Get rid of do_posix_clock_monotonic_gettime
  cris: Replace do_posix_clock_monotonic_gettime()
  tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build
  tick/broadcast: Handle spurious interrupts gracefully
  tick/broadcast: Check for hrtimer broadcast active early
  tick/broadcast: Return busy when IPI is pending
  tick/broadcast: Return busy if periodic mode and hrtimer broadcast
  tick/broadcast: Move the check for periodic mode inside state handling
  tick/broadcast: Prevent deep idle if no broadcast device available
  tick/broadcast: Make idle check independent from mode and config
  tick/broadcast: Sanity check the shutdown of the local clock_event
  tick/broadcast: Prevent hrtimer recursion
  clockevents: Allow set-state callbacks to be optional
  clocksource/imx: Define clocksource for mx27

Pull irq fix from Thomas Gleixner:
 "A single fix for a cpu hotplug race vs. interrupt descriptors:

  Prevent irq setup/teardown across the cpu starting/dying parts of cpu
  hotplug so that the starting/dying cpu has a stable view of the
  descriptor space.  This has been an issue for all architectures in the
  cpu dying phase, where interrupts are migrated away from the dying
  cpu.  In the starting phase its mostly a x86 issue vs the vector space
  update"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hotplug: Prevent alloc/free of irq descriptors during cpu up/down

	Normally opening a file, unlinking it and then closing will have
the inode freed upon close() (provided that it's not otherwise busy and
has no remaining links, of course).  However, there's one case where that
does *not* happen.  Namely, if you open it by fhandle with cold dcache,
then unlink() and close().

	In normal case you get d_delete() in unlink(2) notice that dentry
is busy and unhash it; on the final dput() it will be forcibly evicted from
dcache, triggering iput() and inode removal.  In this case, though, we end
up with *two* dentries - disconnected (created by open-by-fhandle) and
regular one (used by unlink()).  The latter will have its reference to inode
dropped just fine, but the former will not - it's considered hashed (it
is on the ->s_anon list), so it will stay around until the memory pressure
will finally do it in.  As the result, we have the final iput() delayed
indefinitely.  It's trivial to reproduce -

void flush_dcache(void)
{
        system("mount -o remount,rw /");
}

static char buf[20 * 1024 * 1024];

main()
{
        int fd;
        union {
                struct file_handle f;
                char buf[MAX_HANDLE_SZ];
        } x;
        int m;

        x.f.handle_bytes = sizeof(x);
        chdir("/root");
        mkdir("foo", 0700);
        fd = open("foo/bar", O_CREAT | O_RDWR, 0600);
        close(fd);
        name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0);
        flush_dcache();
        fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR);
        unlink("foo/bar");
        write(fd, buf, sizeof(buf));
        system("df .");			/* 20Mb eaten */
        close(fd);
        system("df .");			/* should've freed those 20Mb */
        flush_dcache();
        system("df .");			/* should be the same as #2 */
}

will spit out something like
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 303843      1131 100% /
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 303843      1131 100% /
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 283282     21692  93% /
- inode gets freed only when dentry is finally evicted (here we trigger
than by remount; normally it would've happened in response to memory
pressure hell knows when).

Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/
Acked-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

when opening a directory we want the overlayfs inode, not one from
the topmost layer.
Reported-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Tested-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Cc: stable@vger.kernel.org # all branches
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull libnvdimm fixes from Dan Williams:
 "1) Fixes for a handful of smatch reports (Thanks Dan C.!) and minor
     bug fixes (patches 1-6)

  2) Correctness fixes to the BLK-mode nvdimm driver (patches 7-10).

     Granted these are slightly large for a -rc update.  They have been
     out for review in one form or another since the end of May and were
     deferred from the merge window while we settled on the "PMEM API"
     for the PMEM-mode nvdimm driver (ie memremap_pmem, memcpy_to_pmem,
     and wmb_pmem).

     Now that those apis are merged we implement them in the BLK driver
     to guarantee that mmio aperture moves stay ordered with respect to
     incoming read/write requests, and that writes are flushed through
     those mmio-windows and platform-buffers to be persistent on media.

  These pass the sub-system unit tests with the updates to
  tools/testing/nvdimm, and have received a successful build-report from
  the kbuild robot (468 configs).

  With acks from Rafael for the touches to drivers/acpi/"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
  nfit: add support for NVDIMM "latch" flag
  nfit: update block I/O path to use PMEM API
  tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
  tools/testing/nvdimm: fix return code for unimplemented commands
  tools/testing/nvdimm: mock ioremap_wt
  pmem: add maintainer for include/linux/pmem.h
  nfit: fix smatch "use after null check" report
  nvdimm: Fix return value of nvdimm_bus_init() if class_create() fails
  libnvdimm: smatch cleanups in __nd_ioctl
  sparse: fix misplaced __pmem definition

Pull i2c fixes from Wolfram Sang:
 "Mostly slight adjusments for new drivers, but also one core fix for
  which finally the dependencies are now available as well"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: Mark instantiated device nodes with OF_POPULATE
  i2c: jz4780: Fix return value if probe fails
  i2c: xgene-slimpro: Fix missing mbox_free_channel call in probe error path
  i2c: I2C_MT65XX should depend on HAS_DMA

Pull input fixes from Dmitry Torokhov:
 "A fix (revert) for a recent regression in Synaptics driver and a fix
  for Elan i2c touchpad driver"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Revert "Input: synaptics - allocate 3 slots to keep stability in image sensors"
  Input: elan_i2c - change the hover event from MT to ST

Pull clk fixes from Stephen Boyd:
 "A small set of fixes for problems found by smatch in new drivers that
  we added this rc and a handful of driver fixes that came in during the
  merge window"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  drivers: clk: st: Incorrect register offset used for lock_status
  clk: mediatek: mt8173: Fix enabling of critical clocks
  drivers: clk: st: Fix mux bit-setting for Cortex A9 clocks
  drivers: clk: st: Add CLK_GET_RATE_NOCACHE flag to clocks
  drivers: clk: st: Fix flexgen lock init
  drivers: clk: st: Fix FSYN channel values
  drivers: clk: st: Remove unused code
  clk: qcom: Use parent rate when set rate to pixel RCG clock
  clk: at91: do not leak resources
  clk: stm32: Fix out-by-one error path in the index lookup
  clk: iproc: fix bit manipulation arithmetic
  clk: iproc: fix memory leak from clock name

Pull drm fixes from Dave Airlie:
 "A bunch of fixes for radeon, intel, omap and one amdkfd fix.

  Radeon fixes are all over, but it does fix some cursor corruption
  across suspend/resume.  i915 should fix the second warn you were
  seeing, so let us know if not.  omap is a bunch of small fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
  drm/radeon: disable vce init on cayman (v2)
  drm/amdgpu: fix timeout calculation
  drm/radeon: check if BO_VA is set before adding it to the invalidation list
  drm/radeon: allways add the VM clear duplicate
  Revert "Revert "drm/radeon: dont switch vt on suspend""
  drm/radeon: Fold radeon_set_cursor() into radeon_show_cursor()
  drm/radeon: unpin cursor BOs on suspend and pin them again on resume (v2)
  drm/radeon: Clean up reference counting and pinning of the cursor BOs
  drm/amdkfd: validate pdd where it acquired first
  Revert "drm/i915: Allocate context objects from stolen"
  drm/i915: Declare the swizzling unknown for L-shaped configurations
  drm/radeon: fix underflow in r600_cp_dispatch_texture()
  drm/radeon: default to 2048 MB GART size on SI+
  drm/radeon: fix HDP flushing
  drm/radeon: use RCU query for GEM_BUSY syscall
  drm/amdgpu: Handle irqs only based on irq ring, not irq status regs.
  drm/radeon: Handle irqs only based on irq ring, not irq status regs.
  drm/i915: Use crtc_state->active in primary check_plane func
  drm/i915: Check crtc->active in intel_crtc_disable_planes
  drm/i915: Restore all GGTT VMAs on resume
  ...

Pull selinux fixes from James Morris.

* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  selinux: fix mprotect PROT_EXEC regression caused by mm change
  selinux: don't waste ebitmap space when importing NetLabel categories