Before reworking a little bit the JEDEC detection code, let's
clean the coding style of an if statement to improve readability.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-10-miquel.raynal@bootlin.com

Use a macro to define the number of parameter page instead of
hardcoding it everywhere.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-9-miquel.raynal@bootlin.com

During detection the logic on the NAND bus is:

    /* Regular ONFI detection */
    1/ read the three NAND parameter pages

    /* Extended parameter page detection */
    2/ send "read the NAND parameter page" commands without reading
       actual data
    3/ move the column pointer to the extended page and read it

If fact, as long as there is nothing happening on the NAND bus between
1/ and 3/, the operation 2/ is redundant so remove it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-8-miquel.raynal@bootlin.com

There is no need for copying the parameter page, playing with
pointers does the trick.

There is not functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-7-miquel.raynal@bootlin.com

Use a macro to define the number of parameter page instead of
hardcoding it everywhere.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-6-miquel.raynal@bootlin.com

Before reworking a little bit the ONFI detection code, let's
clean the coding style of the if statements to improve readability.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-5-miquel.raynal@bootlin.com

During ONFI detection, the CRC derived from the parameter page and the
CRC supposed to be at the end of the parameter page are compared. If
they do not match, the second then the third copies of the page are
tried.

The current implementation compares the newly derived CRC with the CRC
contained in the first page only. So if this particular CRC area has
been corrupted, then the detection will fail for a wrong reason.

Fix this issue by checking the derived CRC against the right one.

Fixes: 39138c1f ("mtd: rawnand: use bit-wise majority to recover the ONFI param page")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-4-miquel.raynal@bootlin.com

tR and tCCS are currently wrongly expressed in femtoseconds, while we
expect these values to be expressed in picoseconds. Set right
hardcoded values.

Fixes: 6a943386 mtd: rawnand: add default values for dynamic timings
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-3-miquel.raynal@bootlin.com

Convert the timings union into a structure containing the mode and the
actual values. The values are still a union in prevision of the
addition of the NVDDR modes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-2-miquel.raynal@bootlin.com

There is no correction involved at this point, it is just a matter of
reading registers and checking whether bitflips have occurred or
not. Rename the function to clarify it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-7-miquel.raynal@bootlin.com

Cosmetic change to clarify the purpose of the function.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-6-miquel.raynal@bootlin.com

Ensure all chips are deregistered and cleaned in case of error during
the probe.

Fixes: 02f26ecf ("mtd: nand: add reworked Marvell NAND controller driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-5-miquel.raynal@bootlin.com

Do not call nand_release() while the MTD device has not been
registered, use nand_cleanup() instead.

Fixes: 02f26ecf ("mtd: nand: add reworked Marvell NAND controller driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-4-miquel.raynal@bootlin.com

Switch from the old platform_get_resource()/devm_ioremap_resource()
couple to the newer devm_platform_ioremap_resource() helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-3-miquel.raynal@bootlin.com

In a previous fix, I changed the condition on which the timeout of an
IRQ is reached from:

    if (!ret)

into:

    if (ret && !pending)

While having a non-zero return code is usual in the Linux kernel, here
ret comes from a wait_for_completion_timeout() which returns 0 when
the waiting period is too long.

Hence, the revised condition should be:

    if (!ret && !pending)

The faulty patch did not produce any error because of the !pending
condition so this change is finally purely cosmetic and does not
change the actual driver behavior.

Fixes: cafb56dd ("mtd: rawnand: marvell: prevent timeouts on a loaded machine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-2-miquel.raynal@bootlin.com

When the ECC strength is too weak compared to the NAND chip
requirements, display the values so that it is clear for people how
much they are far from the requirements (and might get in troubles in
the future).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200421163906.7515-1-miquel.raynal@bootlin.com

To match the types passed by au1550nd_exec_instr() function.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200419193037.1544035-5-boris.brezillon@collabora.com

Now that exec_op() is implemented we can get rid of all other hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200419193037.1544035-4-boris.brezillon@collabora.com

So we can later get rid of the legacy interface implementation.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200419193037.1544035-3-boris.brezillon@collabora.com

We are about to re-use those for the exec_op() implementation which
will not rely on au1550_hwcontrol(). Let's patch those helpers to
simply use the iomem address stored in the context.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200419193037.1544035-2-boris.brezillon@collabora.com

The Denali IP have several registers to specify how many clock cycles
should be waited between falling/rising signals. You can improve the
NAND access performance by programming these registers with optimized
values.

Because struct nand_sdr_timings represents the device requirement
in pico seconds, denali_setup_data_interface() computes the register
values by dividing the device timings with the clock period.

Marek Vasut reported this driver in the latest kernel does not work
on his SOCFPGA board. (The on-board NAND chip is mode 5)

The suspicious parameter is acc_clks, so this commit relaxes it.

The Denali NAND Flash Memory Controller User's Guide describes this
register as follows:

  acc_clks
    signifies the number of bus interface clk_x clock cycles,
    controller should wait from read enable going low to sending
    out a strobe of clk_x for capturing of incoming data.

Currently, acc_clks is calculated only based on tREA, the delay on the
chip side. This does not include additional delays that come from the
data path on the PCB and in the SoC, load capacity of the pins, etc.

This relatively becomes a big factor on faster timing modes like mode 5.

Before supporting the ->setup_data_interface() hook (e.g. Linux 4.12),
the Denali driver hacks acc_clks in a couple of ways [1] [2] to support
the timing mode 5.

We would not go back to the hard-coded acc_clks, but we need to include
this factor into the delay somehow. Let's say the amount of the additional
delay is 10000 pico sec.

In the new calculation, acc_clks is determined by timings->tREA_max +
data_setup_on_host.

Also, prolong the RE# low period to make sure the data hold is met.

Finally, re-center the data latch timing for extra safety.

[1] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L276
[2] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L282Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200317071821.9916-1-yamada.masahiro@socionext.com

->exec_op() is passed a check_only argument that encodes when the
controller should just check whether the operation is supported or not
without executing it. Some controllers simply ignore this arguments,
others don't but keep modifying some of the registers before returning.
Let's fix all those drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200418194217.1016060-1-boris.brezillon@collabora.com

Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200417101129.35556-1-yuehaibing@huawei.com

Fix sparse warning:

drivers/mtd/nand/raw/cadence-nand-controller.c:2595:5:
 warning: symbol 'cadence_nand_attach_chip' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200410115228.30440-1-yuehaibing@huawei.com

Fix sparse warning:

drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c:105:32:
 warning: symbol 'qi_lb60_ooblayout_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200410115121.11852-1-yuehaibing@huawei.com

No need to use expensive atomic change_bit() on dat[] and err_idx[]:
1. fsmc_bch8_correct_data() is called while mutex chip->lock is held
2. err_idx[] is a local variable.

To avoid big endian concern due to type cast to unsigned long, directly
change the bit in the specified byte instead of using non-atomic
__change_bit().
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1576886755-9788-1-git-send-email-fenghua.yu@intel.com

Pull cifs fixes from Steve French:
 "Five cifs/smb3 fixes:two for DFS reconnect failover, one lease fix for
  stable and the others to fix a missing spinlock during reconnect"

* tag '5.7-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix uninitialised lease_key in open_shroot()
  cifs: ensure correct super block for DFS reconnect
  cifs: do not share tcons with DFS
  cifs: minor update to comments around the cifs_tcp_ses_lock mutex
  cifs: protect updating server->dstaddr with a spinlock

Pull USB fixes from Greg KH:
 "Here are a number of USB driver fixes for 5.7-rc3.

  Nothing huge, just the usual collection of:

   - xhci fixes

   - gadget driver fixes

   - syzkaller fuzzing fixes

   - new device ids and DT bindings

   - new quirks added for broken devices

  A few of the gadget driver fixes show up twice here as they were
  applied to my branch, and also by Felipe to his branch which I then
  pulled in as we got out of sync a bit.

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
  USB: sisusbvga: Change port variable from signed to unsigned
  usb-storage: Add unusual_devs entry for JMicron JMS566
  USB: hub: Revert commit bd0e6c96 ("usb: hub: try old enumeration scheme first for high speed devices")
  USB: hub: Fix handling of connect changes during sleep
  usb: typec: altmode: Fix typec_altmode_get_partner sometimes returning an invalid pointer
  xhci: Don't clear hub TT buffer on ep0 protocol stall
  xhci: prevent bus suspend if a roothub port detected a over-current condition
  xhci: Fix handling halted endpoint even if endpoint ring appears empty
  usb: raw-gadget: Fix copy_to/from_user() checks
  usb: raw-gadget: fix raw_event_queue_fetch locking
  usb: gadget: udc: atmel: Fix vbus disconnect handling
  usb: dwc3: gadget: Fix request completion check
  USB: Add USB_QUIRK_DELAY_CTRL_MSG and USB_QUIRK_DELAY_INIT for Corsair K70 RGB RAPIDFIRE
  phy: tegra: Select USB_COMMON for usb_get_maximum_speed()
  usb: typec: tcpm: Ignore CC and vbus changes in PORT_RESET change
  usb: f_fs: Clear OS Extended descriptor counts to zero in ffs_data_reset()
  cdc-acm: introduce a cool down
  cdc-acm: close race betrween suspend() and acm_softint
  UAS: fix deadlock in error handling and PM flushing work
  UAS: no use logging any details in case of ENODEV
  ...

Pull tty/serial fixes from Greg KH:
 "Here are some tty and serial driver fixes for 5.7-rc3.

  The "largest" in here are a number of reverts for previous changes to
  the uartps serial driver that turned out to not be a good idea at all.

  The others are just small fixes found by people and tools. Included in
  here is a much-reported symbol export needed by previous changes that
  happened in 5.7-rc1. All of these have been in linux-next for a while
  with no reported issues"

* tag 'tty-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: hvc: fix buffer overflow during hvc_alloc().
  tty: rocket, avoid OOB access
  tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart
  vt: don't hardcode the mem allocation upper bound
  tty: serial: owl: add "much needed" clk_prepare_enable()
  vt: don't use kmalloc() for the unicode screen buffer
  tty/sysrq: Export sysrq_mask(), sysrq_toggle_support()
  serial: sh-sci: Make sure status register SCxSR is read in correct sequence
  serial: sunhv: Initialize lock for non-registered console
  Revert "serial: uartps: Register own uart console and driver structures"
  Revert "serial: uartps: Move Port ID to device data structure"
  Revert "serial: uartps: Change uart ID port allocation"
  Revert "serial: uartps: Do not allow use aliases >= MAX_UART_INSTANCES"
  Revert "serial: uartps: Fix error path when alloc failed"
  Revert "serial: uartps: Use the same dynamic major number for all ports"
  Revert "serial: uartps: Fix uartps_major handling"

Pull char/misc driver fixes from Greg KH:
 "Here are 4 small misc driver fixes for 5.7-rc3:

   - mei driver fix

   - interconnect driver fix

   - two fpga driver fixes

  All have been in linux-next with no reported issues"

* tag 'char-misc-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  interconnect: qcom: Fix uninitialized tcs_cmd::wait
  mei: me: fix irq number stored in hw struct
  fpga: dfl: pci: fix return value of cci_pci_sriov_configure
  fpga: zynq: Remove clk_get error message for probe defer

Pull staging/IIO driver fixes from Greg KH:
 "Here are some small staging and IIO driver fixes for 5.7-rc3

  Lots of tiny things for reported issues in staging and IIO drivers,
  including a counter driver fix as well (the iio drivers seem to be
  tied to those). Full details of the fixes are in the shortlog.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (27 commits)
  staging: vt6656: Fix calling conditions of vnt_set_bss_mode
  staging: comedi: Fix comedi_device refcnt leak in comedi_open
  staging: vt6656: Fix pairwise key entry save.
  staging: vt6656: Fix drivers TBTT timing counter.
  staging: vt6656: Don't set RCR_MULTICAST or RCR_BROADCAST by default.
  MAINTAINERS: remove Stefan Popa's email
  iio: adc: ad7192: fix null pointer de-reference crash during probe
  iio: core: remove extra semi-colon from devm_iio_device_register() macro
  iio: adc: ti-ads8344: properly byte swap value
  iio: imu: inv_mpu6050: fix suspend/resume with runtime power
  iio: st_sensors: rely on odr mask to know if odr can be set
  iio: xilinx-xadc: Make sure not exceed maximum samplerate
  iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
  iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
  iio: xilinx-xadc: Fix ADC-B powerdown
  iio: dac: ad5770r: fix off-by-one check on maximum number of channels
  iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
  iio: core: Fix handling of 'dB'
  dt-bindings: iio: adc: stm32-adc: fix id relative path
  counter: 104-quad-8: Add lock guards - generic interface
  ...

Pull driver core fixes from Greg KH:
 "Here are some small firmware/driver core/debugfs fixes for 5.7-rc3.

  The debugfs change is now possible as now the last users of
  debugfs_create_u32() have been fixed up in the different trees that
  got merged into 5.7-rc1, and I don't want it creeping back in.

  The firmware changes did cause a regression in linux-next, so the
  final patch here reverts part of that, re-exporting the symbol to
  resolve that issue. All of these patches, with the exception of the
  final one, have been in linux-next with only that one reported issue"

* tag 'driver-core-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  firmware_loader: revert removal of the fw_fallback_config export
  debugfs: remove return value of debugfs_create_u32()
  firmware_loader: remove unused exports
  firmware: imx: fix compile-testing

Pull s390 fixes from Vasily Gorbik:

 - Add a few notrace annotations to avoid potential crashes when
   switching ftrace tracers.

 - Avoid setting affinity for floating irqs in pci code.

 - Fix build issue found by kbuild test robot.

* tag 's390-5.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/protvirt: fix compilation issue
  s390/pci: do not set affinity for floating irqs
  s390/ftrace: fix potential crashes when switching tracers

Pull powerpc fixes from Michael Ellerman:

 - One important fix for a bug in the way we find the cache-line size
   from the device tree, which was leading to the wrong size being
   reported to userspace on some platforms.

 - A fix for 8xx STRICT_KERNEL_RWX which was leaving TLB entries around
   leading to a window at boot when the strict mapping wasn't enforced.

 - A fix to enable our KUAP (kernel user access prevention) debugging on
   PPC32.

 - A build fix for clang in lib/mpi.

Thanks to: Chris Packham, Christophe Leroy, Nathan Chancellor, Qian Cai.

* tag 'powerpc-5.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  lib/mpi: Fix building for powerpc with clang
  powerpc/mm: Fix CONFIG_PPC_KUAP_DEBUG on PPC32
  powerpc/8xx: Fix STRICT_KERNEL_RWX startup test failure
  powerpc/setup_64: Set cache-line-size based on cache-block-size

Pull more Devicetree fixes from Rob Herring:
 "A couple of schema and kbuild fixes"

* tag 'devicetree-fixes-for-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: phy: qcom-qusb2: Fix defaults
  dt-bindings: Fix erroneous 'additionalProperties'
  dt-bindings: Fix command line length limit calling dt-mk-schema
  dt-bindings: Re-enable core schemas for dtbs_check

Christoph's patch removed two unsused exported symbols, however, one
symbol is used by the firmware_loader itself.  If CONFIG_FW_LOADER=m so
the firmware_loader is modular but CONFIG_FW_LOADER_USER_HELPER=y we fail
the build at mostpost.

ERROR: modpost: "fw_fallback_config" [drivers/base/firmware_loader/firmware_class.ko] undefined!

This happens because the variable fw_fallback_config is built into the
kernel if CONFIG_FW_LOADER_USER_HELPER=y always, so we need to grant
access to the firmware loader module by exporting it.

Revert only one hunk from his patch.

Fixes: 73960473 ("firmware_loader: remove unused exports")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20200424184916.22843-1-mcgrof@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull pid leak fix from Eric Biederman:
 "Oleg noticed that put_pid(thread_pid) was not getting called when proc
  was not compiled in.

  Let's get that fixed before 5.7 is released and causes problems for
  anyone"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  proc: Put thread_pid in release_task not proc_flush_pid

Pull timer fixlet from Ingo Molnar:
 "A single fix for a comment that may show up in DocBook output"

* tag 'timers-urgent-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  vdso/datapage: Use correct clock mode name in comment

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes:

   - an uclamp accounting fix

   - three frequency invariance fixes and a readability improvement"

* tag 'sched-urgent-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Fix reset-on-fork from RT with uclamp
  x86, sched: Move check for CPU type to caller function
  x86, sched: Don't enable static key when starting secondary CPUs
  x86, sched: Account for CPUs with less than 4 cores in freq. invariance
  x86, sched: Bail out of frequency invariance if base frequency is unknown