After the latest mac80211 changes, the sta has
the ap's sta pointer even before association.

This cause the auth and assoc frames to be sent
with the standard ap's rates, rather than the
basic rates.

Change the tx rate policy logic to use the regular
ap rates only for data packets (so control and mgmt
packets will be sent with basic rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

During interface removal, don't adjust sleep_auth if we are during
recovery. Since the FW is potentially dead we shouldn't talk to it.
Reported-by: Yossi Wortzel <yossiw@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Initialize val to 0, to remove the following warning with
CONFIG_CC_OPTIMIZE_FOR_SIZE. The compiler used was gcc 4.4.1
(Sourcery G++ Lite 2010q1-202).

drivers/net/wireless/ti/wl18xx/io.c: In function 'wl18xx_top_reg_read':
drivers/net/wireless/ti/wl18xx/io.c:57: warning: 'val' may be used uninitialized in this function
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Send EAPOLs using minimum basic rate for AP, STA, p2p GO and Client.
The patch fixes p2p connection issue with Realtek device in p2p
certification test 5.1.13 (DEVUT reinvokes Persistent Group).
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

ht_mode added to wl18xx conf struct in order to support different modes
from the configuration file, as well as module params, and by default
(working without a conf file and/or no module params).
the hack regarding conf.phy.low_band_component_type for each board
is now explicitly handled after parsing module params.
missing default values to wl18xx config added.
fix string module params not to have defaults (so if empty, param
can be taken from conf file).
update conf version to 3.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

suspend and resume callbacks configure wakeup conditions to the FW
which may be different between suspend and resume.
This feature is currently not utilized as both in suspend and resume
FW wakeup every 1 DTIM. Avoid waking up the chip and doing the FW command
unless there's an actual difference in the wakeup conditions.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

We get DMA alignment trouble if the beginning of the conf.phy struct is
not aligned to 4 bytes. Use kmemdup to ensure alignment.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

b43 with open firmware crashes mac80211 because
it changes the number of queues at runtime which,
while it was never really supported, now crashes
mac80211 due to the new hardware queue logic.

Fix this by detecting open vs. proprietary fw
earlier and registering with mac80211 with the
right number of queues.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@vger.kernel.org (depends on commit a6f38ac3)
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using work_pending() to defer certain operations when
a HW-reset work has been queued is racy since the check
would return false when the work item is actually in
execution. Use SC_OP_HW_RESET instead to fix this race.
Also, unify the reset debug statistics maintenance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When an interface in AP or P2P-GO mode is removed,
check whether a station interface is already present and
reconfigure the beacon timers etc. properly if it's
associated.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, there are problems with how ANI is handled in
multi-VIF scenarios. This patch addresses them by unifying
the start/stop logic.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove unused variables, use a helper function to choose
the slot and reset beaconing status at one place.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Setup the beacon queue parameters after disabling
interrupts. Also, remove the redundant call in conf_tx()
for IBSS mode since the queue would be configured
with the appropriate cwmin/cwmax values when beaconing
is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the tx_last_beacon() callback, mac80211's beaconing
status can be used instead. The beacon tasklet doesn't require
it because it is disabled when removing a slot.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* The beaconing status routine is not required, since in
  multi-VIF cases the HW beacon parameters should not be
  re-configured.

* Remove SC_OP_TSF_RESET - when a beaconing interface comes
  up the first time, the TSF has to be reset.

* Simplify ath9k_allow_beacon_config().

* Handle setting/clearing the SWBA interrupt properly.

* Remove the TSF mangling in IBSS mode, it is not required.

* General code cleanup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cleanup the messy logic dealing with station association
and disassociation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* Do not set/clear TSF when adding/deleting an interface.
  This should be done when the BSS is set up and should also
  take into account the existence of other interfaces.

* Set opmode explicitly.

* ANI setup needs to be decided based on multiple interfaces.
  This can be done via the bss_info_changed() callback.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch revamps interface addition and deletion and simplifies
slot allocation. There is no need to setup the beacon buffer
in add/remove interface, remove this and use simple APIs for
assigning/deleting slots.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Same as the recent ath9k fix
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We found a deadlock in the handling of command failures/reset conditions.
For example:

 1. Two commands are in the queue.
 2. The first command is sent, but causes a timeout, which kicks off an
    asynchronous device reset
 3. The second command is queued (but not yet sent to the hardware)
 4. The device reset kicks in, causing the if_usb disconnect handler to
    set the "surprise removed" flag to be set as the device disappears
    from the bus. This causes lbs_thread to stop processing things
    ("adapter removed; waiting to die"), not processing any further
    commands, leaving the second queued command "in the air", causing a
    deadlock.

Fix this by removing the surpriseremoved flag setting in if_usb. I can't
see any reason why this needs to be done so early. lbs_remove_card will set
this flag at an appropriate time - i.e. after all pending commands have
been completed or cancelled, avoiding this deadlock.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fail commands immediately when the request cannot be sent to the hardware.

This solves the following deadlock:
 1. Two commands are in the queue.
 2. The first command is sent, but causes a timeout, which kicks off an
    asynchronous device reset
 3. The second command is submitted to the device, and fails. The failure
    is noted but the existing code waits for the timeout handler to take
    care of the failure.
 4. The device reset kicks in, causing the device "surprise removed" flag
    to be set as the device disappears from the bus.
 5. lbs_thread notes this and enters "adapter removed; waiting to die"
    mode, without processing any further command timeouts.

While adjusting lbs thread logic to handle this situation may be one way
to fix this, it seems more practical to simplify handling of host_to_card
failure so that the commands are failed immediately without waiting for
more compliated timeout logic to kick in.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

reg_notifier can be called before the interface is up.
Handle this correctly by storing the requested country code, then
apply the relevant configuration when the interface is brought up.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

AR9485, AR9330 and AR9340 are the chips that this is *NOT* supposed to be
applied on.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

- add an inline function for getting the correct modal EEPROM struct
- remove unnecessary indirection through ath9k_hw_ar9300_get_eeprom
  access the relevant fields directly
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If the aggregate size exceeds the TXOP limit, it leads to lots of unnecessary
hardware and software retries.

The previous 4ms frame limit table was completely undocumented, the commit
that updated it only vaguely referenced and equation from the standard,
but I've been unable to replicate its results.

Fix this by using a formula based on the code in ath_pkt_duration, which is
more likely to be correct for this case.
Reported-by: Dave Täht <dave.taht@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Prepare for using different queue size defaults for each AC.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In all those years apparently nobody noticed that the txop limit programmed
into the chip was off by a factor of 32 (!), probably because the VI and VO
queues aren't used that much aside from mgmt frames on VO.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The row/column sizes can be derived from the array argument within the macro
itself, which is less error prone. In a few cases the supplied column size
was actually wrong.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use the EEPROM information to choose the right tx gain table
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It has been tested and works properly
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Many chips are not able to deal with non-consecutive rx antenna selections
and respond with calibration errors, reset errors, etc.
When an antenna is selected as a tx antenna, also flag it for rx to avoid
chip issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch configures data rates to firmware using bitrate mask
provided by cfg80211.

Earlier we used to only update band information in this handler
which will be used later for ibss network. Due to recent
modifications in ibss join code we don't need to do that.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>