As we have one to three pinctrl-single instances for each SoC it is
a bit confusing to configure the padconf register offset from the
base of the padconf register base.

Let's add macros that allow using the physical address of the
padconf register directly, or in most cases, just the last 16-bits
of the address as they are shown in the documentation.

Note that most documentation shows two padconf registers for each
32-bit address, so adding 2 to the documentation address is needed for
the second padconf register as we treat them as 16-bit registers
for omap3+.

For example, omap36xx documentation shows sdmmc2_clk at 0x48002158,
so we can just use the last 16-bits of that value:

	pinctrl-single,pins = <
		OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)
		...
	>;

And we don't need to separately calculate the offset from the 0x2030
base:

	pinctrl-single,pins = <
		0x128 (PIN_INPUT_PULLUP | MUX_MODE0)
		...
	>;

Naturally both ways of defining the registers can be used, and I'm
not saying we should replace all the existing defines. But it may
be handy to use these macros for new entries and when doing other
related .dts file clean-up.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: updated for 3430 vs 3630 core2 range]
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds support for CompuLab SBC-T3530, also known as cm-t3730:

http://compulab.co.il/products/sbcs/sbc-t3530/

It seems that with the sbc-3xxx mainboard is also used on
SBC-T3517 and SBC-T3730 with just a different CPU module:

http://compulab.co.il/products/sbcs/sbc-t3517/
http://compulab.co.il/products/sbcs/sbc-t3730/

So let's add a common omap3-sb-t35.dtsi and then separate SoC
specific omap3-sbc-t3730.dts, omap3-sbc-t3530.dts and
omap3-sbc-t3517.dts.

I've tested this with SBC-T3730 as that's the only one I have.
At least serial, both Ethernet controllers, MMC, and wl12xx WLAN
work.

Note that WLAN seems to be different for SBC-T3530. And SBC-T3517
may need some changes for the EMAC Ethernet if that's used
instead of the smsc911x.

Cc: devicetree@vger.kernel.org
Cc: Mike Rapoport <mike@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Let's add the Ethernet so NFSroot works and the first MMC card
so people can patch in more support easily.
Signed-off-by: Tony Lindgren <tony@atomide.com>

As the emac uses the system control module registers for
reset and interrupts, we need to pass those in the platform
data until we have a separate system control module driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>

As we currently need to support a mix of legacy platform data and
device tree intialized data, let's make sure things keep working
for the TWL GPIOs.

Mostly the issue is caused by the fact that DSS does not yet have
device tree bindings, so we need to rely on the TWL GPIO callback
for setting up things like LCD backlight for some boards.

As of_platform_populate() for the TWL GPIO is called by twl-core
after the I2C bus has been initialized, we cannot pass the auxdata
table from the board init code to twl-core like we used to with
just legacy platform data.

So let's use the omap_device bus hook to patch in the platform
data for TWL GPIO until we have sorted out the issues with the
TWL GPIOs and device tree bindings.

The other option was be to initialize twl core using legacy
platform data, which seems like a step backwards as we're moving
to device tree only initialization.  And we really don't want to
add custom configuration functions to the TWL GPIO driver either
for this.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 7ce93f31 (ARM: OMAP2+: Fix more missing data for omap3.dtsi file)
fixed missing device tree data for omaps, but did not account for some of the
hardware modules being inaccessible for secure omaps. This causes the
following error on secure omaps:

Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0c5048
SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W    3.13.0-rc2+ #446
task: ce057b40 ti: ce058000 task.ti: ce058000
PC is at omap_aes_dma_stop+0x24/0x3c
LR is at omap_aes_probe+0x1cc/0x584
   psr: 60000113
sp : ce059e20  ip : ce0b4ee0  fp : 00000000
r10: c0573ae8  r9 : c0749508  r8 : 00000000
r7 : ce0b4e00  r6 : 00000000  r5 : ce0b4e10  r4 : ce274890
r3 : fa0c5048  r2 : 00000048  r1 : 0000002c  r0 : ce274890
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c5387d  Table: 80004019  DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xce058248)
Stack: (0xce059e20 to 0xce05a000)
9e20: c0749508 0000a1ff 00000000 c016cd8c c06b5a06 ce2a45f0 ce2a4570 ce0b5fb0
9e40: 00000000 480c5000 480c504f c0abe4e4 00000200 00000000 00000000 00000000
9e60: ce0b4e10 ce0b4e10 c082da3c c082da3c c02b8c70 c077c610 c0749508 00000000
9e80: 00000000 c02b9e7c c02b9e64 ce0b4e10 00000000 c02b8b20 ce0b4e10 ce0b4e44
9ea0: c082da3c c02b8cd8 00000000 ce059eb8 c082da3c c02b7408 ce079edc ce0b1a34
9ec0: c082da3c c082da3c ce2a0280 00000000 c08158d8 c02b8358 c0663405 c0663405
9ee0: 00000073 c082da3c c079e4e8 c07ab3bc c0844340 c02b9334 00000000 00000006
9f00: c079e4e8 c0008920 c067f6bf c0ac7c6b 00000000 c0712e28 00000000 00000000
9f20: c0712e38 ce059f38 00000093 c0ac7c82 00000000 c0058994 00000000 c07130e8
9f40: c07127b8 00000093 00000006 00000006 00000001 00000006 00000006 c079e4e8
9f60: c07ab3bc c0844340 00000093 c0749508 c079e4f4 c0749c64 00000006 00000006
9f80: c0749508 00000000 00000000 c0517e2c 00000000 00000000 00000000 00000000
9fa0: 00000000 c0517e34 00000000 c000dfb8 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff
(omap_aes_probe+0x1cc/0x584)
(platform_drv_probe+0x18/0x48)
(driver_probe_device+0xb0/0x200)
(__driver_attach+0x68/0x8c)
(bus_for_each_dev+0x50/0x88)
(bus_add_driver+0xcc/0x1c8)
(driver_register+0x9c/0xe0)
(do_one_initcall+0x98/0x140)
(kernel_init_freeable+0x16c/0x23c)
(kernel_init+0x8/0x100)
(ret_from_fork+0x14/0x3c)
Code: e1811002 e5932020 e590300c e0833002 (e593c000)

Let's fix the issue by adding omap34xx-hs.dtsi and omap36xx-hs.dtsi and make
n900, n9 and n950 to use them. This way we have the aes, sham and timer12
disabled for secure devices the same way legacy booting does based on the
omap34xx_gp_hwmod_ocp_ifs and omap36xx_gp_hwmod_ocp_ifs arrays in
omap_hwmod_3xxx_data.c.
Reported-by: Sebastian Reichel <sre@debian.org>
Acked-By: Sebastian Reichel <sre@debian.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The am3517 is wrongly booting as omap3 which means that the am3517
specific devices like Ethernet won't work when booted with device
tree. Now with the new devices defined in am3517.dtsi, let's use
that instead of the omap3.dtsi, and add a separate machine entry
for am3517 so am3517-evm can use it.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated comments and fixed build without omap3]
Signed-off-by: Tony Lindgren <tony@atomide.com>

On am3517 there are some extra devices compared to omap3.dtsi that
we currently have not defined. Let's fix that by adding am3517.dtsi
file.
Signed-off-by: Tony Lindgren <tony@atomide.com>

We have some device tree properties where the ti,hwmod have multiple
values:

am33xx.dtsi:	ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
am4372.dtsi:	ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
dra7.dtsi:	ti,hwmods = "l3_main_1", "l3_main_2";
omap3.dtsi:	ti,hwmods = "mcbsp2", "mcbsp2_sidetone";
omap3.dtsi:	ti,hwmods = "mcbsp3", "mcbsp3_sidetone";
omap4.dtsi:	ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
omap5.dtsi:	ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";

That's not correct way of doing things in this case because these are
separate devices with their own address space, interrupts, SYSCONFIG
registers and can set their PM states independently.

So they should all be fixed up to be separate devices in the .dts files.

We also have the related data removed for at least omap4 in commit
3b9b1015 (ARM: OMAP4: hwmod data: Clean up the data file), so
that data is wrongly initialized as null data.

So we need to fix two bugs:

1. We are only checking the first entry of the ti,hwmods property

   This means that we're only initializing the first hwmods entry
   instead of the ones listed in the ti,hwmods property.

2. We are only checking the child nodes, not the nodes themselves

   This means that anything listed at OCP level is currently just
   ignored and unitialized and at least the omap4 case, with the
   legacy data missing from the hwmod.

Fix both of the issues by using an index to the ti,hwmods property
and changing the hwmod lookup function to also check the current node
for ti,hwmods property instead of just the children.

While at it, let's also add some warnings for the bad data so it's
easier to fix.

Cc: "Benoît Cousson" <bcousson@baylibre.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'trace-fixes-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fix from Steven Rostedt:
 "A regression showed up that there's a large delay when enabling all
  events.  This was prevalent when FTRACE_SELFTEST was enabled which
  enables all events several times, and caused the system bootup to
  pause for over a minute.

  This was tracked down to an addition of a synchronize_sched()
  performed when system call tracepoints are unregistered.

  The synchronize_sched() is needed between the unregistering of the
  system call tracepoint and a deletion of a tracing instance buffer.
  But placing the synchronize_sched() in the unreg of *every* system
  call tracepoint is a bit overboard.  A single synchronize_sched()
  before the deletion of the instance is sufficient"

* tag 'trace-fixes-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Only run synchronize_sched() at instance deletion time

Pull aio fix from Benjamin LaHaise:
 "AIO fix from Gu Zheng that fixes a GPF that Dave Jones uncovered with
  trinity"

* git://git.kvack.org/~bcrl/aio-next:
  aio: clean up aio ring in the fail path

Pull SCSI fixes from James Bottomley:
 "This is a set of nine fixes (and one author update).

  The libsas one should fix discovery in eSATA devices, the WRITE_SAME
  one is the largest, but it should fix a lot of problems we've been
  getting with the emulated RAID devices (they've been effectively lying
  about support and then firmware has been choking on the commands).

  The rest are various crash, hang or warn driver fixes"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] bfa: Fix crash when symb name set for offline vport
  [SCSI] enclosure: fix WARN_ON in dual path device removing
  [SCSI] pm80xx: Tasklets synchronization fix.
  [SCSI] pm80xx: Resetting the phy state.
  [SCSI] pm80xx: Fix for direct attached device.
  [SCSI] pm80xx: Module author addition
  [SCSI] hpsa: return 0 from driver probe function on success, not 1
  [SCSI] hpsa: do not discard scsi status on aborted commands
  [SCSI] Disable WRITE SAME for RAID and virtual host adapter drivers
  [SCSI] libsas: fix usage of ata_tf_to_fis

Pull IMA fixes from James Morris:
 "Here are two more fixes for IMA"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  ima: properly free ima_template_entry structures
  ima: Do not free 'entry' before it is initialized

Pull devicetree fixes from Rob Herring:
 - Various DT binding documentation updates
 - Add Kumar Gala and remove Stephen Warren as DT binding maintainers

* tag 'dt-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt: binding: reword PowerPC 8xxx GPIO documentation
  ARM: tegra: delete nvidia,tegra20-spi.txt binding
  hwmon: ntc_thermistor: Fix typo (pullup-uV -> pullup-uv)
  of: add vendor prefix for GMT
  clk: exynos: Fix typos in DT bindings documentation
  of: Add vendor prefix for LG Corporation
  Documentation: net: fsl-fec.txt: Add phy-supply entry
  ARM: dts: doc: Document missing binding for omap5-mpu
  dt-bindings: add ARMv8 PMU binding
  MAINTAINERS: remove swarren from DT bindings
  MAINTAINERS: Add Kumar to Device Tree Binding maintainers group

Clean up the aio ring file in the fail path of aio_setup_ring
and ioctx_alloc. And maybe it can fix the GPF issue reported by
Dave Jones:
https://lkml.org/lkml/2013/11/25/898Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>

Merge branch 'free-memory' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity into for-linus

Pull power management fixes from Rafael Wysocki:

 - cpufreq regression fix from Bjørn Mork restoring the pre-3.12
   behavior of the framework during system suspend/hibernation to avoid
   garbage sysfs files from being left behind in case of a suspend error

 - PNP regression fix to restore the correct states of devices after
   resume from hibernation broken in 3.12.  From Dmitry Torokhov.

 - cpuidle fix to prevent cpuidle device unregistration from crashing
   due to a NULL pointer dereference if cpuidle has been disabled from
   the kernel command line.  From Konrad Rzeszutek Wilk.

 - intel_idle fix for the C6 state definition on Intel Avoton/Rangeley
   processors from Arne Bockholdt.

 - Power capping framework fix to make the energy_uj sysfs attribute
   work in accordance with the documentation.  From Srinivas Pandruvada.

 - epoll fix to make it ignore the EPOLLWAKEUP flag if the kernel has
   been compiled with CONFIG_PM_SLEEP unset (in which case that flag
   should not have any effect).  From Amit Pundir.

 - cpufreq fix to prevent governor sysfs files from being lost over
   system suspend/resume in some (arguably unusual) situations.  From
   Viresh Kumar.

* tag 'pm-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PowerCap: Fix mode for energy counter
  PNP: fix restoring devices after hibernation
  cpuidle: Check for dev before deregistering it.
  epoll: drop EPOLLWAKEUP if PM_SLEEP is disabled
  cpufreq: fix garbage kobjects on errors during suspend/resume
  cpufreq: suspend governors on system suspend/hibernate
  intel_idle: Fixed C6 state on Avoton/Rangeley processors

* pm-epoll:
  epoll: drop EPOLLWAKEUP if PM_SLEEP is disabled

* pnp:
  PNP: fix restoring devices after hibernation

* powercap:
  PowerCap: Fix mode for energy counter

* pm-cpuidle:
  cpuidle: Check for dev before deregistering it.
  intel_idle: Fixed C6 state on Avoton/Rangeley processors

* pm-cpufreq:
  cpufreq: fix garbage kobjects on errors during suspend/resume
  cpufreq: suspend governors on system suspend/hibernate

Pull arch/tile ftrace bug fix from Chris Metcalf:
 "This fixes a build failure with allyesconfig reported by Fengguang Wu
  and fixed by Tony Lu"

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  ftrace: default to tilegx if ARCH=tile is specified

Pull block layer fixes from Jens Axboe:
 "A small collection of fixes for the current series. It contains:

   - A fix for a use-after-free of a request in blk-mq.  From Ming Lei

   - A fix for a blk-mq bug that could attempt to dereference a NULL rq
     if allocation failed

   - Two xen-blkfront small fixes

   - Cleanup of submit_bio_wait() type uses in the kernel, unifying
     that.  From Kent

   - A fix for 32-bit blkg_rwstat reading.  I apologize for this one
     looking mangled in the shortlog, it's entirely my fault for missing
     an empty line between the description and body of the text"

* 'for-linus' of git://git.kernel.dk/linux-block:
  blk-mq: fix use-after-free of request
  blk-mq: fix dereference of rq->mq_ctx if allocation fails
  block: xen-blkfront: Fix possible NULL ptr dereference
  xen-blkfront: Silence pfn maybe-uninitialized warning
  block: submit_bio_wait() conversions
  Update of blkg_stat and blkg_rwstat may happen in bh context

Pull NFS client bugfixes from Trond Myklebust:
 - Stable fix for a NFSv4.1 delegation and state recovery deadlock
 - Stable fix for a loop on irrecoverable errors when returning
   delegations
 - Fix a 3-way deadlock between layoutreturn, open, and state recovery
 - Update the MAINTAINERS file with contact information for Trond
   Myklebust
 - Close needs to handle NFS4ERR_ADMIN_REVOKED
 - Enabling v4.2 should not recompile nfsd and lockd
 - Fix a couple of compile warnings

* tag 'nfs-for-3.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  nfs: fix do_div() warning by instead using sector_div()
  MAINTAINERS: Update contact information for Trond Myklebust
  NFSv4.1: Prevent a 3-way deadlock between layoutreturn, open and state recovery
  SUNRPC: do not fail gss proc NULL calls with EACCES
  NFSv4: close needs to handle NFS4ERR_ADMIN_REVOKED
  NFSv4: Update list of irrecoverable errors on DELEGRETURN
  NFSv4 wait on recovery for async session errors
  NFS: Fix a warning in nfs_setsecurity
  NFS: Enabling v4.2 should not recompile nfsd and lockd

This matches the existing behavior in arch/tile/Makefile for defconfig.

Reported-by: fengguang.wu@intel.com
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Tony Lu <zlu@tilera.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>

It has been reported that boot up with FTRACE_SELFTEST enabled can take a
very long time. There can be stalls of over a minute.

This was tracked down to the synchronize_sched() called when a system call
event is disabled. As the self tests enable and disable thousands of events,
this makes the synchronize_sched() get called thousands of times.

The synchornize_sched() was added with d562aff9 "tracing: Add support
for SOFT_DISABLE to syscall events" which caused this regression (added
in 3.13-rc1).

The synchronize_sched() is to protect against the events being accessed
when a tracer instance is being deleted. When an instance is being deleted
all the events associated to it are unregistered. The synchronize_sched()
makes sure that no more users are running when it finishes.

Instead of calling synchronize_sched() for all syscall events, we only
need to call it once, after the events are unregistered and before the
instance is deleted. The event_mutex is held during this action to
prevent new users from enabling events.

Link: http://lkml.kernel.org/r/20131203124120.427b9661@gandalf.local.homeReported-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Acked-by: Petr Mladek <pmladek@suse.cz>
Tested-by: Petr Mladek <pmladek@suse.cz>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Pull btrfs MAINTAINERS file update:
 "I'm still getting settled into new devel hardware etc, but I do have
  one commit for the next rc.

  This changes my email over to fb.com, and adds a MAINTAINERS entry for
  Josef as well"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: update the MAINTAINERS file

Pull minor fbdev fixes from Tomi Valkeinen.

* tag 'fbdev-fixes-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
  video: vt8500: fix error handling in probe()
  atmel_lcdfb: fix module autoload
  fbdev: sh_mobile_meram: Fix defined but not used compiler warnings
  video: kyro: fix incorrect sizes when copying to userspace
  ARM: OMAPFB: panel-sony-acx565akm: fix bad unlock balance

Pull sound fixes from Takashi Iwai:
 "A usual pattern of half ASoC and half HD-audio fixes, although
  HD-audio fixups have more volumes, in addition to a couple of trivial
  fixes.  Nothing to worry much is found here.

  For ASoC side: a few fixes for PCM rate constraints calculations,
  regmap byte-order fix, the rest driver specific fixes (atmel, fsl,
  omap, kirkwood, wm codecs).

  For HD-audio: Dell headset and mono out fix, ELD update in polling
  mode, ALC283 Chromebook fixes, a few fixes for old AD codecs and
  MBA2, one regression fix"

* tag 'sound-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
  ALSA: hda - Fix silent output on MacBook Air 2,1
  ALSA: hda - Fix missing ELD info when using jackpoll_ms parameter
  ALSA: hda/realtek - remove hp_automute_hook from alc283_fixup_chromebook
  ASoC: wm8731: fix dsp mode configuration
  ALSA: hda/realtek - Independent of model for HP
  ALSA: hda - Fix headset mic input after muted internal mic (Dell/Realtek)
  ALSA: hda - Use always amps for auto-mute on AD1986A codec
  ALSA: hda/analog - Handle inverted EAPD properly in vmaster hook
  ALSA: hda - Another fixup for ASUS laptop with ALC660 codec
  ALSA: atmel: Fix possible array overflow
  ALSA: hda - Fix complete_all() timing in deferred probes
  ALSA: hda - Fix bad EAPD setup for HP machines with AD1984A
  ASoC: core: fix devres parameter in devm_snd_soc_register_card()
  ASoC: omap: n810: Convert to clk_prepare_enable/clk_disable_unprepare
  ASoC: fsl: set correct platform drvdata in pcm030_fabric_probe()
  ASoC: fsl: imx-pcm-fiq: Remove unused 'runtime' variable
  ASoC: fsl: imx-pcm-fiq: remove bogus period delta calculation
  ALSA: hda - Fix silent output on ASUS W7J laptop
  ASoC: core: Use consistent byte ordering in snd_soc_bytes_get
  ALSA: dice: fix array limits in dice_proc_read()
  ...

Pull pin control fixes from Linus Walleij:

 - Minor bug fixes for the Rockchip, ST-Ericsson abx500, Renesas PFC
   r8a7740 and sh7372.

 - Compilation warning fixes.

* tag 'pinctrl-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  sh-pfc: sh7372: Fix pin bias setup
  sh-pfc: r8a7740: Fix pin bias setup
  pinctrl: abx500: Fix header file include guard
  pinctrl: rockchip: missing unlock on error in rockchip_set_pull()
  pinctrl: abx500: fix some more bitwise AND tests
  pinctrl: rockchip: testing the wrong variable

If accounting is on, we will do the IO completion accounting after
we have freed the request. Fix that by moving it sooner instead.
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull x86 and EFI fixes from Peter Anvin:
 "Half of these are EFI-related:

  The by far biggest change is the change to hold off the deletion of a
  sysfs entry while a backend scan is in progress.  This is to avoid
  calling kmemdup() while under a spinlock.

  The other major change is for each entry in the EFI pstore backend to
  get a unique identifier, as required by the pstore filesystem proper.

  The other changes are:

  A fix to the recent consolidation and optimization of using "asm goto"
  with read-modify-write operation, which broke the bitops; specifically
  in such a way that we could end up generating invalid code.

  A build hack to make sure we compile with -mno-sse.  icc, and most
  likely future versions of gcc, can generate SSE instructions unless we
  tell it not to.

  A comment-only patch to a change the was due in part to an unpublished
  erratum; now when the erratum is published we want to add a comment
  explaining why"

* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic, doc: Justification for disabling IO APIC before Local APIC
  x86, bitops: Correct the assembly constraints to testing bitops
  x86-64, build: Always pass in -mno-sse
  efi-pstore: Make efi-pstore return a unique id
  x86/efi: Fix earlyprintk off-by-one bug
  efivars, efi-pstore: Hold off deletion of sysfs entry until the scan is completed

Since erratum AVR31 in "Intel Atom Processor C2000 Product Family
Specification Update" is now published, I added a justification
comment for disabling IO APIC before Local APIC, as changed in commit:

522e6646 x86/apic: Disable I/O APIC before shutdown of the local APIC
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1386202069-51515-1-git-send-email-fenghua.yu@intel.comSigned-off-by: H. Peter Anvin <hpa@linux.intel.com>

As per the documentation of powercap sysfs, energy_uj field is read only,
if it can't be reset. Currently it always allows write but will fail,
if there is no reset callback.
Changing mode field, to read only if there is no reset callback.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reported-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

On returning from hibernation 'restore' callback is called,
not 'resume'.  Fix it.

Fixes: eaf140b6 (PNP: convert PNP driver bus legacy pm_ops to dev_pm_ops)
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In checkin:

0c44c2d0 x86: Use asm goto to implement better modify_and_test() functions

the various functions which do modify and test were unified and
optimized using "asm goto".  However, this change missed the detail
that the bitops require an "Ir" constraint rather than an "er"
constraint ("I" = integer constant from 0-31, "e" = signed 32-bit
integer constant).  This would cause code to miscompile if these
functions were used on constant bit positions 32-255 and the build to
fail if used on constant bit positions above 255.

Add the constraints as a parameter to the GEN_BINARY_RMWcc() macro to
avoid this problem.
Reported-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/529E8719.4070202@zytor.com

When compiling a 32bit kernel with CONFIG_LBDAF=n the compiler complains like
shown below.  Fix this warning by instead using sector_div() which is provided
by the kernel.h header file.

fs/nfs/blocklayout/extents.c: In function ‘normalize’:
include/asm-generic/div64.h:43:28: warning: comparison of distinct pointer types lacks a cast [enabled by default]
fs/nfs/blocklayout/extents.c:47:13: note: in expansion of macro ‘do_div’
nfs/blocklayout/extents.c:47:2: warning: right shift count >= width of type [enabled by default]
fs/nfs/blocklayout/extents.c:47:2: warning: passing argument 1 of ‘__div64_32’ from incompatible pointer type [enabled by default]
include/asm-generic/div64.h:35:17: note: expected ‘uint64_t *’ but argument is of type ‘sector_t *’
 extern uint32_t __div64_32(uint64_t *dividend, uint32_t divisor);
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

Andy Adamson reports:

The state manager is recovering expired state and recovery OPENs are being
processed. If kswapd is pruning inodes at the same time, a deadlock can occur
when kswapd calls evict_inode on an NFSv4.1 inode with a layout, and the
resultant layoutreturn gets an error that the state mangager is to handle,
causing the layoutreturn to wait on the (NFS client) cl_rpcwaitq.

At the same time an open is waiting for the inode deletion to complete in
__wait_on_freeing_inode.

If the open is either the open called by the state manager, or an open from
the same open owner that is holding the NFSv4 sequence id which causes the
OPEN from the state manager to wait for the sequence id on the Seqid_waitqueue,
then the state is deadlocked with kswapd.

The fix is simply to have layoutreturn ignore all errors except NFS4ERR_DELAY.
We already know that layouts are dropped on all server reboots, and that
it has to be coded to deal with the "forgetful client model" that doesn't
send layoutreturns.
Reported-by: Andy Adamson <andros@netapp.com>
Link: http://lkml.kernel.org/r/1385402270-14284-1-git-send-email-andros@netapp.comSigned-off-by: Trond Myklebust <Trond.Myklebust@primarydata.com>

Pull GPIO fixes from Linus Walleij:
 "Here are a few more GPIO patches, we're a bit noisy for being the GPIO
  subsystem, mostly due to the new descriptor API, but all is getting
  into shape.

   - Fix compile warnings

   - Fix overly talkative diagnostic messages from usual use cases wrt
     GPIO descriptors

   - Add a documentation 00-INDEX

   - Use platform GPIOs as fallback when ACPI or device tree is used as
     the primary means to get GPIO lines

   - A bug fix for the MPC8572/MPC8536 fixing erroneous input data"

* tag 'gpio-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpiolib: change a warning to debug message when failing to get gpio
  powerpc/gpio: Fix the wrong GPIO input data on MPC8572/MPC8536
  gpiolib: use platform GPIO mappings as fallback
  Documentation: gpiolib: add 00-INDEX file
  gpiolib: fix lookup of platform-mapped GPIOs
  gpiolib: add missing declarations