From: Michael Hunold <hunold@convergence.de>

The attached patch changes my "Multimedia eXtension Board" (MXB)
Video4Linux-driver to use the standard saa7111 video decoder infrastructure
(to which I recently submitted changes through Ronald Bultje) instead of
some home-brewn direct-access stuff.

Nothing serious, but it removes code duplication and makes the code use the
video decoder api.

From: <viro@parcelfarce.linux.theplanet.co.uk>

init/initramfs.c::do_skip() has an off-by-one that leads to unpacking
failures for some gzipped cpio images.  We have

static int __init do_skip(void)
{
        if (this_header + count <= next_header) {
                eat(count);
                return 1;
        } else {
                eat(next_header - this_header);
                state = next_state;
                return 0;
        }
}

and that <= should actually be <.  It almost never matters, since if we hit
the boundary case (header ending exactly on the gunzip window end) the
current variant will simply end up doing extra call of do_skip() when we
get to the next window and that will finish the work (assign state).  The
only exception is when we hit that in the last window.  That is, if there's
nothing after the final header (trailer).  Then we miss the final state
transition (Skip -> Reset) and get "junk in archive" panic.  Normally
cpio(1) pads the image to multiple of 512, so we actually have a bunch of
zeroes after the trailer.  And that almost always saves our butts - trailer
is followed by zeroes, so we get to Reset state just fine.

So we never see that on small in-kernel image (it's less than 512 bytes, so
it gets a lot of padding) and we almost never see that on external ones
(1:127 odds of hitting the bug).

From: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>

- use fat_fs_panic() instead of BUG() if it read a corrupted inode.

- add missing "\n".

From: Pavel Machek <pavel@suse.cz>

swsusp contained rather nasty bug where it killed machine when intel-agp or
anything else split kernel 4MB mapping.  Herbert Xu diagnosed this.  Fixed by
switching to "known good" mapping for during suspend/resume.

From: Bart Samwel <bart@samwel.tk>

We don't want to use "cut" in the laptop mode control script, because that
is in /usr.  This patch is from Jasper Spaans.

Signed-off-by: Petr Vandrovec <vandrove@vc.cvut.cz>

Some people expressed interest in having possibility to set CRTC <->
outputs mapping at boot time, without having to use 'matroxset' later after
kernel boots.

This patch adds option 'video=matroxfb:outputs:XYZ', where X sets which
CRTC will connect to primary output, Y sets secondary output and Z sets DVI
output.

In addition to that I also added missing memset() into maven, which was
broken since i2c was kobjectified.

From: Andi Kleen <ak@muc.de>

When start_transaction() detects an error it already calls ext3_std_error. 
No need to do it again in the caller.

From: Christoph Hellwig <hch@lst.de>

From: Debian kernel package, author probably Herbert Xu

Include asm/io.h and asm/scatterlist.h in include/asm-i386/dma-mapping.h to
make it useable standalone, which is already true for most architectures.

From: "Sergey S. Kostyliov" <rathamahata@php4.ru>

Fix a typo in an error message.

From: Christoph Hellwig <hch@lst.de>

From: Debian kernel package, author probably Herbert Xu

From: Christoph Hellwig <hch@lst.de>

* Include linux/root_dev.h for ROOT_DEV in drivers/mtd/maps/uclinux.c

From: Christoph Hellwig <hch@lst.de>

again needed by most non-x86 arches.

 * Include linux/init.h for __init

From: Christoph Hellwig <hch@lst.de>

From: Mattia Monga via Debian kernel package

Add support for nm256xl+ in sound/oss/nm256_audio.c

From: Christoph Hellwig <hch@lst.de>

From: Debian kernel package, author is probably Herbert Xu

 * Do not get seqno since we will not use it in fs/isofs/inode.c

From: Christoph Hellwig <hch@lst.de>

From: Debian kernel package, author probably Herbert Xu.

 * Fixed bashism in Makefile

From: "Sergey S. Kostyliov" <rathamahata@php4.ru>

Fix nls support for character sets with character width large than 1.

From: Roman Zippel <zippel@linux-m68k.org>

Update dir ctime/mtime when adding/removing an entry.

From: Roman Zippel <zippel@linux-m68k.org>

When releasing a page don't try to release not existing nodes.

From: Roman Zippel <zippel@linux-m68k.org>

If the inserting of the file or dir record failed, remove the previously
inserted thread record.

From: Roman Zippel <zippel@linux-m68k.org>

Call hfsplus_delete_inode() to delete an inode when adding it to the
filesystem failed, so superblock info is correctly updated.

From: Roman Zippel <zippel@linux-m68k.org>

Initialize d_fsdata field also for dir dentries, use hfsplus_instantiate
helper function for this.

From: Roman Zippel <zippel@linux-m68k.org>

Use the correct key length for index nodes.

From: Kurt Garloff <garloff@suse.de>

Attached patch decreases the size of struct file by 8 bytes on 64 bit arches
by avoiding unecessary padding.

From: Christoph Hellwig <hch@lst.de>

struct page easily fits into a single cacheline with any recent CPU, and the
ordering isn't as described anymore anyway.

From: Christoph Hellwig <hch@lst.de>

there's no user is modules, the function isn't in mainline and I don't see why
modules should use it.

From: Olaf Kirch <okir@suse.de>

I have been chasing a corruption of current->group_info on PPC during NFS
stress tests.  The problem seems to be that nfsd is messing with its
group_info quite a bit, while some monitoring processes look at
/proc/<pid>/status and do a get_group_info/put_group_info without any locking.

This problem can be reproduced on ppc platforms within a few seconds if you
generate some NFS load and do a "cat /proc/XXX/status" of an nfsd thread in a
tight loop.

I therefore think changes to current->group_info, and querying it from a
different process, needs to be protected using the task_lock.

(akpm: task->group_info here is safe against exit() because the task holds a
ref on group_info which is released in __put_task_struct, and the /proc file
has a ref on the task_struct).

ep_send_events() uses ~350 bytes of stack for a local buffer of events to send
to userspace.  The patch fixes that by removing the double-buffering
altogether.  A pipe-based microbenchmark from Davide Libenzi
<davidel@xmailserver.org> was sped up by 1-2%.

From: Ingo Molnar <mingo@elte.hu>

printk currently does

	if (oops_in_progres)
		bust_printk_locks();

which means that once we oops, the printk locking is 100% ineffective and
multiple CPUs make an unreadable mess on a serial console.  It's a significant
development hassle.

Fix that up by only popping locks once per ten seconds.

akpm@osdl.org did:

  - Bump the timeout to 30 seconds - 9600 baud is slow.

  - Handle jiffy wraps: change the logic so that we only skip the lockbust
    if the current time is within 30 seconds of the previous lockbusting
    attempt.

From: "J. Bruce Fields" <bfields@fieldses.org>

The kernel currently prints:

 nfsd: nobody listening for auth.unix.ip upcall; has some daemon not been started?

on every bootup, during initscripts.

Neil Brown <neilb@cse.unsw.edu.au> says:

  It was part of the recent set of idmapper patches.  Bruce wanted the admin
  to get a warning when the idmapper daemon wasn't running.  I thought the
  same warning should apply to any daemon that responded to upcalls.

  In the case of auth.unix.ip it isn't strictly necessary for a daemon to be
  running (for comparability with 2.4).

  You can get rid of the warning by doing:

    mount -t nfsd nfsd /proc/fs/nfs

  before mountd is started (init scripts should start doing this I hope, but
  distributions don't tend to use the init script from nfs-utils, so it is
  hard to push it).  This will trigger mountd to listen on auth.unix.ip and
  others.


That's a hassle, so Bruce's patch limits the warning purely to the new
idmapper cache.  It provides a callback in the cache_detail that individual
caches can use to log messages when upcalls fail because a userspace daemon
not running.  Implement this method for the idmapping caches.

From: Mans Rullgard <mru@kth.se>

There are a few include which should have been under __KERNEL__.

Signed-off-by: Paul Mackerras <paulus@samba.org>

Early in the boot process on pSeries machines, we look in the Open Firmware
device tree for information about the interrupt assignments, and assign
virtual IRQ numbers for each physical IRQ.  There is currently a couple of
bugs in this code which result in us assigning virtual IRQs for nonexistent
physical IRQs.  This causes problems when we call the firmware to enable or
disable those nonexistent physical IRQs.  Some versions at least of the
firmware will hit an assertion failure and crash the machine when this
happens.

This patch fixes the bugs and ensures that we don't try and use nonexistent
physical IRQ numbers.  One bug was that we were mapping ISA interrupts,
which is unnecessary since virtual IRQ numbers 0 - 15 are reserved for
them.  The other was that when we had a PCI interrupt (which is always in
the range 1 to 4, corresponding to INTA to INTD) which didn't have a
mapping in the PCI host bridge above it, we were just using the original
number (usually 1) rather than ignoring it.

Signed-off-by: Anton Blanchard <anton@samba.org>

We have cards that want over 2MB of PCI consistent memory.  The
IOMAP_MAX_ORDER limit is just to catch bad drivers early, so we can bump
this a bit.

We want some room to grow but our maximum get_free_pages allocation on
ppc64 is currently 16MB, so it doesnt make sense to go above that.

From: Anton Blanchard <anton@samba.org>

enter_rtas now takes an unsigned long.

From: Stephen Rothwell <sfr@canb.auug.org.au>

This patch allows us to dynamically add virtual disks to an iSeries partition.
 It works like this: after you have created the virtual disk file on OS/400
and attached it to the Linux partition, you need to write to
/sys/bus/vio/drivers/viodasd/probe (it doesn't matter what you write).  This
will do the probe.  It calls add_disk() for each new disk, so we get hotplug
events as a side effect.

This was the nicest way I could think of doing this as the interface to the
hypervisor is polled ...

From: Anton Blanchard <anton@samba.org>

From: Olaf Hering and Nathan Lynch:

Fix a couple of nasty lurking bugs in viopath.c and add information
required to know if the iseries_veth module should be loaded on legacy
iSeries systems.

From: Anton Blanchard <anton@samba.org>

From: Anton Blanchard, Dave Hansen and Olof Johansson:

Fix multiple bugs in the ppc64 NUMA topology probe code.

- We were using HW cpu numbers instead of logical ones.  615, 630, 650,
  some 670 and some 690 SMP will all fail to boot without this patch.

- The old code would BUG() when it got confused (more NUMA zones than the
  kernel is configured for etc).

- The common depth calculation was incorrect.  Dave found an OF property
  that gives us exactly what we want.

- Things were broken on SMT machines.

The new code should work on those broken systems and should no longer BUG()
but fall back to a flat topology when it gets confused.

From: Anton Blanchard <anton@samba.org>

In _raw_spin_lock_flags we were branching to the wrong spot and would
restore random stuff to the MSR.

From: Zdenek Pavlas <pavlas@nextra.cz>

On any x86 without cpuid, early_cpu_detect() left x86_cache_alignment as
zero, so kmem_cache_init() calls cache_estimate() with align == 0, and
it loops forever. I've tried this trivial fix, and it works for me.

Andi Kleen looked over this, and ok'd it.

This improves the stack traces we get on PPC64 by putting a marker in
those stack frames that are created as a result of an interrupt or
exception.  The marker is "regshere" (0x7265677368657265).

With this, stack traces show where exceptions have occurred, which can
be very useful.  This also improves the accuracy of the trace because
the relevant return address can be in the link register at the time of
the exception rather than on the stack.  We now print the PC and
exception type for each exception frame, and then the link register if
appropriate as the next item in the trace.