Renesas R-Car sound SRC (= Sampling Rate Converter) has
Asynchronous/Synchronous SRC mode. Asynchronous mode is already
supported via DPCM. This patch adds Synchronous mode on it.

The condition of enabling Synchronous mode are
- SoC is clock master
- Sound uses SRC
- Sound doesn't use DVC
- Sound card uses DPCM (= rsrc-card card)

	amixer set "SRC Out Rate" on
	aplay xxx.wav &
	amixer set "SRC Out Rate" 48000
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

A driver's device data should and can be const. This is a follow-up on
commit 33187fb4 (ASoC: rsnd: constify of_device_id array) which
marked the of_device_id as const.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch supports DPCM based sampling rate convert on Renesas sound
driver. It assumes...
 1. SRC is implemented as FE
 2. BE dai_link supports .be_hw_params_fixup
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch removes useless debug message. especially some kind of
"probed" message will be printed from core.c if it has #define DEBUG
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

clk_prepare_enable()/clk_disable_unprepare() uses mutex inside,
in concretely clk_prepare()/clk_unprepare().And it uses __schedule().
Then, raw_spin_lock/unlock_irq() is called, and it breaks Renesas
sound driver's spin lock irq.
This patch separates thesse into clk_prepare()/clk_unprepare() and
clk_enable/clk_disable. And call clk_prepare()/clk_unprepare() from
probe/remove function. Special thanks to Das Biju.
Reported-by: Das Biju <biju.das@bp.renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Current rsnd-dpcm-card is supporting DPCM FE/BE sound card.
This patch adds .be_hw_params_fixup and enabled sampling convert rate.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Renesas sound card has "sampling rate convert" feature which
should be implemented via DPCM.
But, sound card driver point of view, it is difficult to add
this DPCM feature on simple-card driver. Especially, DT binding
support is very difficult.

This patch implements DPCM feature on DT as Renesas specific sound card.
This new driver is copied from current simple-card driver.
Main difference between simple-card and this driver are...
 1. removed unused feature from simple-card
 2. removed driver named prefix from DT property
 3. CPU will be FE, CODEC will be BE with snd-soc-dummy
 4. it supports sampling rate convert via .be_hw_params_fixup
 5. board specific routing is implemented in driver
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Replace duplicated const keyword for 'dvc_ramp_rate' with proper
array of const pointers to const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds missing dai_link stream_name
which is used when DPCM
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This driver sometimes fixups debug/error message format
30cc4faf
(ASoC: rsnd: tidyup debug message format and timing)
337b0b4c
(ASoC: rsnd: error meesage indicates its port)
But, it still exist un-fomated error message. This patch fixup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

It will be SRC interrupt endless loop f unusual situation happen.
This patch adds restart limit for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

It will be SSI interrupt endless loop f unusual situation happen.
This patch adds restart limit for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>

Renesas sound driver needs SSI/SRC/DVC regmaps, but it didn't have
regmap_config::name for devm_regmap_init_mmio().
Thus, debugfs initialization code tried to use same driver name
many times, and failed.
This patch adds eacy own name for regmap_config::name
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Renesas sound driver needs 1st/2nd DMA interface,
and 1st DMA is using DMAEngine, and 2nd is using local method now.
2nd DMA had been DMAEngine, but it was moved to local method by previous
patchset. But then, it lost PIO mode fallback when probe.
this patch recovers it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

sound/soc/sh/rcar/dma.c: In function 'rsnd_dmapp_init':
sound/soc/sh/rcar/dma.c:341:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
  dev_dbg(dev, "id/src/dst/chcr = %d/%x/%x/%08x\n",
  ^
sound/soc/sh/rcar/dma.c:341:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]

Fixes: 288f392e ("ASoC: rsnd: add Audio DMAC peri peri support rework")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Current rsnd driver supports reg-names, and Audio DMAC peri peri.
This patch adds sample code for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

rsnd driver supports Audio DMAC (via DMAEngine) /
Audio DMAC peri peri (via rsnd driver) now.
This patch adds DT binding sample code on DT binging text
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

cfcefe01
(ASoC: rsnd: add recovery support for under/over flow error on SRC)
added SRC recovery support which needs IRQ.
This patch adds SRC irq sample code on DT bingdings text
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Renesas R-Car sound (= rsnd) needs 2 DMAC which are called as
Audio DMAC (= 1st DMAC) and Audio DMAC peri peri (2nd DMAC).
And rsnd had assumed that 1st / 2nd DMACs are implemented as DMAEngine.
But, in result of DMA ML discussion, 2nd DMAC was concluded that it is
not a general purpose DMAC (2nd DMAC is for Device to Device inside
sound system). Additionally, current DMAEngine can't support Device to
Device, and we don't have correct DT bindings for it at this point.
So the easiest solution for it is that move it from DMAEngine to rsnd
driver.

dma-names on DT was implemented as no difference between 1st / 2nd
DMAC's, since rsnd had assumed that both DMACs are implemented as
DMAEngine. That style was "src_dst". But now, 2nd DMAC was implemented
as non DMAEngine, and it doesn't need dma-names anymore. So, this
dma-names rule is no longer needed.

And additionally, dma-names was assumed that it has all
(= SSI/SSIU/SRC/DVC) nodes under sound node.

In upstream code, no SoC/platform is supporting DMA for rsnd driver yet.
This means there is no compatible issue if this patch changes
dma-names's rule of DT.

This patch assumes dma-names for 1st DMAC are tx/rx base, and listed
in each SSI/SRC/DVC subnode
ex)
	rcar_sound,dvc {
		dvc0: dvc@0 {
			dmas = <&audma0 0xbc>;
			dma-names = "tx";
		};
	...

	rcar_sound,src {
		src0: src@0 {
			...
			dmas = <&audma0 0x85>, <&audma1 0x9a>;
			dma-names = "rx", "tx";
		};
	...

	rcar_sound,ssi {
		ssi0: ssi@0 {
			...
			dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>;
			dma-names = "rx", "tx", "rxu", "txu";
		};
	...
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds rsnd_dvc_of_node() to get DVC subnode from DT.
This is prepare for new DT bindings for 1st DMAC
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds rsnd_src_of_node() to get SRC subnode from DT.
This is prepare for new DT bindings for 1st DMAC
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds rsnd_ssi_of_node() to get SSI subnode from DT.
This is prepare for new DT bindings for 1st DMAC
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Renesas R-Car sound driver uses SSI, but the DMA interfaces are
SSI/SSIU. This interface is based on SSI/SRC/DVC connection.
And DMA function needs to know which interface is used somehow.
This patch enables rsnd_ssi_use_busif() for DMA.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Renesas R-Car needs 2 DMACs.1st DMAC is DMAEngine, and 2nd DMAC is
implemented as local code. These 2 DMACs are never shared.
We can use union for these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

DMAEngine direction can be calculated from rsnd_dai_stream,
So, rsnd_dma::dir does not make sense now.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

DMAEngine for Renesas R-Car driver is used only for Audio DMAC now.
rsnd_dma::addr was added to support Audio DMAC peri peri,
but it is no longer needed. Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Renesas R-Car sound (= rsnd) needs 2 DMAC which are called as
Audio DMAC (= 1st DMAC) and Audio DMAC peri peri (2nd DMAC).
And rsnd had assumed that 1st / 2nd DMACs are implemented as DMAEngine.
But, in result of DMA ML discussion, 2nd DMAC was concluded that it is
not a general purpose DMAC (2nd DMAC is for Device to Device inside
sound system). Additionally, current DMAEngine can't support Device to
Device, and we don't have correct DT bindings for it at this point.
So the easiest solution for it is that move it from DMAEngine to rsnd
driver.
Audio DMAC peri peri is controlled from sound driver without DMAEngine
by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

rsnd driver needs to care about Audio DAMC (via DMAEngine),
Audio DMAC peri peri (via local method) on rsnd driver.
This patch adds new rsnd_dma_ops and care it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Now, we have dma.c for Audio DMAC / Audio DMAC peri peri.
rsnd_gen_dma_addr() should go there.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Renesas sound driver had been assumed that Audio DMAC /
Audio DMAC peri peri are implemented by DMAEngine. But, result of DMA
ML discussion, it was concluded that it is not a general purpose DMAC.
And it should be moved from current DMAEngine to rsnd driver.
So, Audio DMAC peri peri become non DMAEngine.

OTOH, ALSA SoC has soc-generic-dmaengine-pcm implementation. but it
seems difficult to use this generic implementation on rsnd driver at
this point, since it needs to fallback to PIO mode if DMA can't use.
and additionally it needs 2 DMAC (= Audio DMAC / Audio DMAC peri peri).
These are not "generic" feature.

Of course I will try to use this generic dmaengine in the future somehow,
but just use current style at this point until it can formally use 2 DMACs.
This patch adds new dma.c and moves current dma code to dma.c from core.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

physical address is required from Audio DMAC peri peri.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

rsnd driver needs to support Audio DMAC peri peri inside sound driver.
getting resource by name is useful for it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

priv is not used on rsnd_dma_quit()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

rsnd_dma_available() is not used. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

It can get DMA direction via rsnd_dai_stream.
Remove un-needed is_play from rsnd_dma_init().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>