Remove some unnecessary includes, an out of date comment and a prototype for
sys_timer_create (which is now in syscalls.h)
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

- Make ioprio syscalls return long, like set/getpriority syscalls.
- Move function prototypes into syscalls.h so we can pick them up in the
  32/64bit compat code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Enable the runlatch at the start of each exception.  Unfortunately we are out
of space in the 0x300 handler, so I added it a bit later.

The SPR write is fairly expensive, perhaps we should cache the runlatch state
in the paca and avoid the write when possible.

We don't need to turn the runlatch off, we do that in the idle loop.  Better
to take the hit in the idle loop than for each exception exit.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Not all ppc64 CPUs have the CTRL SPR, so we need a cputable feature for it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Use c99 initialisers in the cputable code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Patch from <amodra@bigpond.net.au>,
http://sources.redhat.com/bugzilla/show_bug.cgi?id=1042

/usr/bin/ld: arch/ppc64/kernel/vdso32/vdso32.so: The first section in the
PT_DYNAMIC segment is not the .dynamic section
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch adds support for some new PHY models to sungem as used on some
recent Apple iMac G5 models.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Using the syntax:
make dir/module.ko

kbuild now allows one to build a module including the final link stage.
This is usefull when one only wants to compile a single module and thus do
not have to wait until a full kernel has finished compiling.  Tested by:
randy_dunlap <rdunlap@xenotime.net>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

  make O=/dir TAGS

  fails with:

    MAKE   TAGS
  find: security/selinux/include: No such file or directory
  find: include: No such file or directory
  find: include/asm-i386: No such file or directory
  find: include/asm-generic: No such file or directory

  The problem is in this line:
  ifeq ($(KBUILD_OUTPUT),)

KBUILD_OUTPUT is not defined (ever) after make reruns itself.  This line is
used in the TAGS, tags, and cscope makes.
Signed-off-by: George Anzinger <george@mvista.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

We now print statistics when invoking the OOM killer, however this
information is not rate limited and you can get into situations where the
console is continually spammed.

For example, when a task is exiting the OOM killer will simply return
(waiting for that task to exit and clear up memory).  If the VM continually
calls back into the OOM killer we get thousands of copies of show_mem() on
the console.

Use printk_ratelimit() to quieten it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Remove completly bogus comment from did_some_progress != 0 handling (that
same comment is a few lines below on did_some_progress = 0 case, where it
belongs).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Dump the current allocation order when OOM killing.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

OCFS2 wants to mark an inode which has been orphaned by another node so
that during final iput it takes the correct path through the VFS and can
pass through the OCFS2 delete_inode callback.  Since i_nlink can get out of
date with other nodes, the best way I see to accomplish this is by clearing
i_nlink on those inodes at drop_inode time.  Other than this small amount
of work, nothing different needs to happen, so I think it would be cleanest
to be able to just call generic_drop_inode at the end of the OCFS2
drop_inode callback.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Various stuff missing on alpha:

drivers/message/i2o/config-osm.c:35: error: field `fops' has incomplete type
drivers/message/i2o/config-osm.c: In function `sysfs_create_fops_file':
drivers/message/i2o/config-osm.c:71: error: storage size of `tmp' isn't known
drivers/message/i2o/config-osm.c:78: error: dereferencing pointer to incomplete type
drivers/message/i2o/config-osm.c:81: error: dereferencing pointer to incomplete type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

We get sporadic reports of `__iounmap: bad address' coming out.  Add a
dump_stack() to find the culprit.

Try to identify which subsystem is having iounmap() problems.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

There is absolutely no reason to flush the kernel's VM area during a
tlb_flush_mm.

This results in a noticable performance increase in the kernel build
benchmark.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Disable the tiocx driver on non-SN systems.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Jesse Barnes provided the original version of this patch months ago, but
other changes kept conflicting with it, so it got deferred.  Greg Edwards
dug it out of obscurity just over a week ago, and almost immediately
another conflicting patch appeared (Bob Picco's memory-less nodes).

I've resolved the conflicts and got it running again.  CONFIG_SGI_TIOCX
is set to "y" in defconfig, which causes a Tiger to not boot (oops in
tiocx_init).  But that can be resolved later ... get this in now before it
gets stale again.
Signed-off-by: Tony Luck <tony.luck@intel.com>

There is a slight disagreement between setup-bus.c code and traditional
x86 PCI setup wrt which recourses are invalid vs resources that are free
for further allocations.

In particular, in the setup-bus.c, if we failed to allocate some resource,
we nullify "start" and "flags" fields, but *not* the "end" one.

But x86 pcibios_enable_resources() does the following check:

	if (!r->start && r->end) {
		printk(KERN_ERR "PCI: Device %s not available because of resource collisions\n", pci_name(dev));
		return -EINVAL;

which means that the device owning the offending resource cannot be
enabled.

In particular, this breaks cardbus behind the normal decode p2p bridge -
the cardbus code from setup-bus.c requests rather large IO and MEM
windows, and if it fails, the socket is completely unavailable.  Which
is wrong, as the yenta code is capable to allocate smaller windows.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

I reworked how nodes with only CPUs are treated.  The patch below seems
simpler to me and has eliminated the complicated routine
reassign_cpu_only_nodes.  There isn't any longer the requirement
to modify ACPI NUMA information which was in large part the
complexity introduced in reassign_cpu_only_nodes. 

This patch will produce a different number of nodes. For example,
reassign_cpu_only_nodes would reduce two CPUonly nodes and one memory node
configuration to one memory+CPUs node configuration.  This patch
doesn't change the number of nodes which means the user will see three.  Two
nodes without memory and one node with all the memory.

While doing this patch, I noticed that early_nr_phys_cpus_node isn't serving
any useful purpose.  It is called once in find_pernode_space but the value
isn't used to computer pernode space.  
Signed-off-by: bob.picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Call ebus_dma_enable() before calling ebus_dma_request(), otherwise
ebus_dma_request() returns -EINVAL and enable_dma() calls BUG()...
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Do not cat bucket->irq_info to struct irqaction * directly,
but go through struct irq_desc *.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

restore_sigcontext calls ia64_set_local_fpu_owner() which requires that
preempt be disabled.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

This patch fixes an issue with the PROM and a kernel running with
CONFIG_PREEMPT enabled.  When CONFIG_PREEMPT is enabled, the size of a
spinlock_t changes -- resulting in the PROM writing to an incorrect location.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

This patch is the SGI hotplug driver and additional changes required for
the driver.  These modifications include changes to the SN io_init.c code
for memory management, the inclusion of new SAL calls to enable and disable
PCI slots, and a hotplug-style driver.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

This patch is a rewrite of the code to check the PROM version.  The current
code has some deficiences in the way PROM comparisons were made.  The minimum
value of PROM that will boot has also been changed to 4.04.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

The pci_find_next_bus function is listed as being exported to drivers.  It is
not EXPORT_SYMBOL'd.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

This patch moves header files out of the arch/ia64/sn directories and into
include/asm-ia64/sn.  These files were being included by other subsystems
and should be under include/asm-ia64/sn.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Patch from Deepak Saxena

This patch implements the iomap API for Intel IXP4xx NPU systems.
We need to implement our own version of the API functions b/c of the
PCI hostbridge does not provide the capability to map PCI I/O space
into the CPU's physical memory space. In addition, if a system has
more than 64M of PCI memory mapped BARs, PCI memory must also be
accessed indirectly.  This patch changes the assignment of PCI I/O
resources to fall into to 0x0000:0xffff range so that we can trap
I/O areas in our ioread/iowrite macros.

Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Todd Poynor

Fix module versioning for 3 ARM symbols that do not have CRCs added,
avoid "disagrees about version of symbol struct_module" errors at module
load time.  From David Singleton.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

	coyote

Patch from Stefan Sorensen

On the ixdp425 and coyote platforms, the plat_serial8250_port arrays are
missing the terminating entry required by serial8250_probe.
Signed-off-by: Stefan Sorensen <ssoe@kirktelecom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Catalin Marinas

The VFP instructions trigger undefined exceptions because the access to
CP11 is disabled (only CP10 is currently enabled by the kernel). The patch
fixes this problem.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>