- 13 Feb, 2017 40 commits
-
-
Ritesh Harjani authored
platform_execute_tuning should not really exist as it does not do anything useful. So remove this ops and directly plug sdhci_msm_execute_tuning with mmc_host_ops. Also in case of HS400 tuning clear SDHCI_HS400_TUNING flag once HS400 related mode selection is done. Signed-off-by:
Ritesh Harjani <riteshh@codeaurora.org> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Ulf Hansson authored
When mmc_of_parse() finds the binding, it sets the mmc cap, MMC_CAP_3_3V_DDR, which informs the core whether eMMC DDR at 3.3V I/O is supported by the mmc host. Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Tested-by:
Jan Glauber <jglauber@cavium.com> Tested-by:
Stefan Wahren <stefan.wahren@i2se.com>
-
Ulf Hansson authored
Cc: <devicetree@vger.kernel.org> Cc: Rob Herring <robh@kernel.org> Signed-off-by:
Rob Herring <robh@kernel.org>
-
Ulf Hansson authored
According the JEDEC specification an eMMC card supporting 1.8V vccq in DDR mode should also be capable of 3.3V. However, it's been reported that some mmc hosts supports 3.3V, but not 1.8V. Currently the mmc core implements an error handling when the host fails to set 1.8V for vccq, by falling back to 3.3V. Unfortunate, this seems to be insufficient for some mmc hosts. To enable these to use eMMC DDR mode let's invent a new mmc cap, MMC_CAP_3_3V_DDR, which tells whether they support the eMMC 3.3V DDR mode. In case MMC_CAP_3_3V_DDR is set, but not MMC_CAP_1_8V_DDR, let's change to remain on the 3.3V, as it's the default voltage level for vccq, set by the earlier power up sequence. As this change introduces MMC_CAP_3_3V_DDR, let's take the opportunity to do some re-formatting of the related defines in the header file. Signed-off-by:
-
Ulf Hansson authored
Earlier the mmc_set_signal_voltage() existed, but since it has been renamed to mmc_set_uhs_voltage(), we can now use that name instead. Signed-off-by:
-
Ulf Hansson authored
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to 1.8V for UHS mode. To clarify this let's do the following changes. - We are always providing MMC_SIGNAL_VOLTAGE_180 as the signal_voltage parameter to the function. Then, let's just remove the parameter as it serves no purpose. - Rename the function to mmc_set_uhs_voltage(). Signed-off-by:
-
Ulf Hansson authored
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to 1.8V for UHS mode. Therefore let's remove the redundant code dealing with MMC_SIGNAL_VOLTAGE_330. Signed-off-by:
-
Chris Brandt authored
In the case of a single clock source, you don't need names. However, if the controller has 2 clock sources, you need to name them correctly so the driver can find the 2nd one. The 2nd clock is for the internal card detect logic. Signed-off-by:
Chris Brandt <chris.brandt@renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by:
-
Chris Brandt authored
Some controllers have 2 clock sources instead of 1. The 2nd clock is for the internal card detect logic and must be enabled/disabled along with the main core clock for proper operation. Signed-off-by:
-
Kevin Hilman authored
Cleanup some debug prints that cause needless noise during normal usage. Signed-off-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
-
Linus Walleij authored
The mmc_blk_issue_rq() function is called in exactly one place in queue.c and there the return value is ignored. So the functions called from that function that also meticulously return 0/1 do so for no good reason. Error reporting on the asynchronous requests are done upward to the block layer when the requests are eventually completed or fail, which may happen during the flow of the mmc_blk_issue_* functions directly (for "special commands") or later, when an asynchronous read/write request is completed. The issuing functions do not give rise to errors on their own, and there is nothing to return back to the caller in queue.c. Drop all return values and make the function return void. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Linus Walleij authored
Recycling the same variable in an x=x+1 fashion may seem clever here but it makes the code terse and hard to follow for humans. Introduce a new_areq and old_areq variable so we see what is going on. Signed-off-by:
-
Linus Walleij authored
Setting rqc to NULL followed by a goto to cmd_abort is just a way to do unconditional abort without starting any new command. Inline the calls to mmc_blk_rw_cmd_abort() and return immediately in those cases. Add some comments to the code flow so it is clear that this is where the asynchronous requests come back in and the result of them gets handled. Signed-off-by:
-
Linus Walleij authored
The code in mmc_blk_issue_rq_rq() aborts a command if the request is not properly aligned on large sectors. As part of the path jumping out, it assigns the local variable mq_rq reflecting a MMC queue request to the current MMC queue request, which is confusing since the variable is not used after this jump. Signed-off-by:
-
Linus Walleij authored
As a step toward breaking apart the very complex function mmc_blk_issue_rw_rq() we break out the code to start a new request. Signed-off-by:
-
Linus Walleij authored
As a first step toward breaking apart the very complex function mmc_blk_issue_rw_rq() we break out the command abort code. This code assumes "ret" is != 0 and then repeatedly hammers blk_end_request() until the request to the block layer to end the request succeeds. Signed-off-by:
-
Jaehoon Chung authored
Use the bitops API instead of shifting directly. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
-
Jaehoon Chung authored
Remove the sdhci-s3c-regs.h file. Instead, it located those defined values into sdhci-s3c.c. Signed-off-by:
-
Wolfram Sang authored
Before enabling SDIO irqs, clear the status bit, so we discard old and stale interrupts. Needed to get two wireless cards working. Use the newly introduced macro in all places. Signed-off-by:
-
Wolfram Sang authored
QUIRK sounds like there is something wrong, but actually there are just some bits which need to be 1. Rename it to be more clear. Signed-off-by:
-
Wolfram Sang authored
tmio_mmc_sdio_irq() is not used as a seperate irq handler anymore, so we can make it similar to the other irq helper functions, namely: * only give the host as argument function which is what it really needs * prefix function name with __ Signed-off-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
Matt Ranostay authored
Allow power sequencing for the Marvell SD8787 Wifi/BT chip. This can be abstracted to other chipsets if needed in the future. Cc: Tony Lindgren <tony@atomide.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Matt Ranostay <matt@ranostay.consulting> Signed-off-by:
-
Matt Ranostay authored
Cc: Rob Herring <robh@kernel.org> Cc: devicetree@vger.kernel.org Signed-off-by:
-
Wolfram Sang authored
Create a helper function to disable clocks and use it in remove(), too. Now, clk_summary in debugfs reports the clocks as disabled and unprepared after unbinding. Signed-off-by:
-
Ritesh Harjani authored
This provides enhanced_strobe mode feature support in sdhci-msm driver. Signed-off-by:
Jeremy McNicoll <jeremymc@redhat.com> Acked-by:
-
Ritesh Harjani authored
During tuning execution for HS400 mode, HW sequence recommends to select MCLK_SEL/2(0x3) in VENDOR_SPEC & sdhc msm clock at GCC to be 400MHZ (nearest supported clk). Add this change in tuning sequence during HS400 tuning. Signed-off-by:
-
Ritesh Harjani authored
Clear SDHCI_HS400_TUNING flag after platform_execute_tuning so that platform_execute_tuning may use it if needed. Signed-off-by:
-
Subhash Jadavani authored
Program CORE_CSR_CDC_DELAY_CFG for hardware recommended 1.25ns delay. We may see data CRC errors if it's programmed for any other delay value. Signed-off-by:
Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by:
-
Venkat Gopalakrishnan authored
The vendor specific func register doesn't get reset when using the software reset register. The various bootloader's could leave this in an unknown state, hence reset this register to it's power on reset value during probe. Signed-off-by:
Venkat Gopalakrishnan <venkatg@codeaurora.org> Signed-off-by:
-
Ritesh Harjani authored
Factor out sdhci_msm_hs400 used for DLL calibration in HS400 modes. This function will be needed for enhanced_strobe as well. Signed-off-by:
-
Ritesh Harjani authored
Factor out msm_set/get_clock_rate_for_bus_mode for it's later use in changing the tuning sequence for selecting HS400 bus speed mode. Signed-off-by:
-
Ritesh Harjani authored
This factors out sdhci_msm_hc_select_mode to later use it during enhanced_strobe mode select. It also further breaks sdhci_msm_hc_select_mode into separate functions for configuring HS400 mode or other modes. Signed-off-by:
-
Stefan Wahren authored
This patch implements support for multiblock transfers bounded by SET_BLOCK_COUNT (CMD23) on the MXS MMC host driver. Signed-off-by:
-
Alexey Khoroshilov authored
host->dma_addr can store a value that is not returned by the DMA API, so it is safer to check if is a valid DMA address indirectly. Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Zhang Rui authored
With commit 67bf5156 ("gpio / ACPI: fix returned error from acpi_dev_gpio_irq_get()"), mmc_gpiod_request_cd() returns -EPROBE_DEFER if GPIO is not ready when sdhci-acpi driver is probed, and sdhci-acpi driver should be probed again later in this case. This fixes an order issue when both GPIO and sdhci-acpi drivers are built as modules. CC: stable@vger.kernel.org # v4.9 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177101Tested-by:
Jonas Aaberg <cja@gmx.net> Signed-off-by:
Zhang Rui <rui.zhang@intel.com> Acked-by:
-
Ulf Hansson authored
Using extern when declaring functions in the public header, core.h, is redundant. Let's just remove the use of it. Signed-off-by:
-
Ulf Hansson authored
A significant amount of functions are available through the public mmc host.h header file. Let's slim down this public mmc interface, as to prevent users from abusing it, by moving some of the functions to private mmc host.h header file. This change concentrates on moving the functions into private mmc headers, following changes may continue with additional clean-ups. Signed-off-by:
-
Ulf Hansson authored
A significant amount of functions and other definitions are available through the public mmc card.h header file. Let's slim down this public mmc interface, as to prevent users from abusing it, by moving some of the functions/definitions to private mmc header files. This change concentrates on moving the functions into private mmc headers, following changes may continue with additional clean-ups. Signed-off-by:
-
Ulf Hansson authored
The mmc_card_present() function helps the mmc core to track an internal state of the card device. More importantly, it's not intended to be used by mmc host drivers to check for an inserted card. Therefore, let's stop using it and instead rely on checking for a valid pointer to a struct mmc_card, as it should be good enough. Signed-off-by:
-
Ulf Hansson authored
The mmc_card_present() function helps the mmc core to track an internal state of the card device. More importantly, it's not intended to be used by mmc host drivers to check for an inserted card. Therefore, let's stop using it and instead rely on checking for a valid pointer to a struct mmc_card, as it should be good enough. Cc: linux-omap@vger.kernel.org Cc: Tony Lindgren <tony@atomide.com> Cc: Jarkko Nikula <jarkko.nikula@bitmer.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Reviewed-by:
-
