This patch enables quirk handling for Silicon Wave based devices and
fixes kernel bug with id 42985.

T:  Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#=  6 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0c10 ProdID=0000 Rev=15.00
S:  Manufacturer=SiW
S:  Product=SiW
S:  SerialNumber=340A05F61100
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr= 50mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Peter Poklop <peter.poklop@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

debugfs_create_bool is asking to put u32 type pointer instead of bool
so that passing bool type with u32* cast will cause memory corruption
to read that value since it is handled by 4 bytes instead of 1 byte
inside.
Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The kbuild test robot reported implicit declaration of function
'acpi_dev_get_resources'.

Surround ACPI function by CONFIG_ACPI test.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

devm_gpiod_get currently has an optional parameter to set initial
direction and value for the requested gpio. Make use of this to simplify
the driver and make it not fail to build when this parameter is made
mandatory (which is scheduled for 4.3-rc1).

Moreover use the _optional variant of devm_gpiod_get to simplify error
handling (which also gets more strict for free).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds a 6lowpan.txt into the networking documentation
directory. Currently this documentation describes how the lowpan
private data of net devices will be handled.

Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Suggested-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch moves module_init of 6lowpan module into core functionality
of 6lowpan module. To load the ipv6 module at probing of the 6lowpan
module should be core functionality. Loading next header compression
modules is iphc specific. Nevertheless we only support IPHC for the
generic 6LoWPAN branch right now so we can put it into the core
functionality. If possible new compression formats are introduced nhc
should load only when iphc is build.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch introduced the 6lowpan netdev private data struct. We name it
lowpan_priv and it's placed at the beginning of netdev private data. All
lowpan interfaces should allocate this room at first of netdev private
data. 6LoWPAN LL private data can be allocate by additional netdev private
data, e.g. dev->priv_size should be "sizeof(struct lowpan_priv) +
sizeof(LL_LOWPAN_PRIVATE_DATA)".
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The usually way to get the btle lowpan private data is to use the
introduced lowpan_dev inline function. This patch will cleanup by using
lowpan_dev consequently.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Add reference to hci_uart structure to bcm_device.
This allows suspend/resume callbacks to manage UART flow control.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Parse platform_device's ACPI to retrieve UART init speed.
When BCM device is open, check if its TTY has same parent as one of the
platform devices saved. If yes, use platform_device's init speed.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Power management support for BCM2E39 is now performed in Bluetooth
BCM UART driver.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Retrieve "shutdown" and "device_wakeup" GPIOs from ACPI.
Set device off during platform device enumeration.
Set device on only when attached.
As driver can be unbound we need to check if the bcm_device still exists
before calling GPIO's functions, this is protected using device_list_lock.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When the device tree support is disabled, the fifo_pin is uninitialized,
this patch will set the fifo_pin value based on platform data
Signed-off-by: Yong Li <sdliyong@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

QCA61x4 chips have supported sleep feature using In-Band-Sleep commands
to enable sleep feature based on H4 protocol. After sending
patch/nvm configuration is done, IBS mode will be up and running
Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This is for supporting BT for QCA ROME with vendor specific
HCI commands and initialization on the chip. This will have
USB/UART implementation both, but for now, adding UART vendor
specific commands to patch downloading and set Bluetooth device
address using vendor specific command.
Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.

This patch enables new connection establishment procedure. Instead of just
sending HCI_OP_LE_CREATE_CONN to controller, "connect" will add device to
kernel whitelist and start scan. If advertisement is received, it'll be
compared against whitelist and then trigger connection if it matches.
That fixes mentioned reconnect issue for  already paired devices. It also
make whole connection procedure more robust. We can try to connect to
multiple devices at same time now, even though controller allow only one.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.

This patch makes sure that when new procedure is in use, and we're stuck
in scan phase because no advertisement was received and timeout happened,
or app decided to close socket, scan whitelist gets properly cleaned up.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.

This path makes sure that after advertisement is received from device that
we try to connect to, it is properly handled in check_pending_le_conn and
trigger connect attempt.

It also modifies hci_le_connect to make sure that connect attempt will be
properly continued.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.

This patch adds hci_connect_le_scan with dependencies, new method that
will be used to connect to remote LE devices. Instead of just sending
connect request, it adds a device to whitelist. Later patches will make
use of this whitelist to send conenct request when advertisement is
received, and properly handle timeouts.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds hci_lookup_le_connect method, that will be used to check
wether outgoing le connection attempt is in progress.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.

This patch adds some fields to hci_conn_params, in preparation to new
connect procedure.

explicit_connect will be used to override any current auto_connect action,
and connect to device when ad is received.

HCI_AUTO_CONN_EXPLICIT was added to auto_connect enum. When this value
will be used, explicit connect is the only action, and params can be
removed after successful connection.

HCI_CONN_SCANNING is added to hci_conn flags. When it's set, connect is
scan phase. It gets cleared when advertisement is received, and
HCI_OP_LE_CREATE_CONN is sent.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch fixes the error handling for lowpan_xmit_fragment by replace
"-PTR_ERR" to "PTR_ERR". PTR_ERR returns already a negative errno code.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch introduce a new mib entry which isn't part of 802.15.4 but
useful as default behaviour to set the ack request bit or not if we
don't know if the ack request bit should set. This is currently used for
stacks like IEEE 802.15.4 6LoWPAN.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch changes the state change behaviour of at86rf230 to always
TX_ARET mode. According the at86rf2xx datasheets TX_ARET mode doesn't
mean to be always waiting for ack frames after transmit. The transceiver
will automatically wait for ack frames or not if the acknowledge request
bit is set. See section "TX_ARET_ON – Transmit with Automatic Frame
Retransmission and CSMA-CA Retry".
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch changes the default minimum value of frame_retries to 0 and
changes the frame_retries default value to 3 which is also 802.15.4
default.

We don't use the frame_retries "-1" value as indicator for no-aret mode
anymore, instead we checking on the ack request bit inside the 802.15.4
frame control field. This allows a acknowledge handling per frame. This
checking is done by transceiver or inside xmit callback of driver layer.

If a transceiver doesn't support ARET handling the transmit
functionality ignores ack frames then, which isn't well but should not
effect anything of current functionality.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes several checks if a value is really changed. This
makes only sense if we have another layer call e.g. calling the
driver_ops which is done by callbacks like "set_channel".

For MAC settings which need to be set by phy registers (if the phy
supports that handling) this is set by doing an interface up currently
and are not direct driver_ops calls, so we remove the checks from these
configuration callbacks.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Suggested-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If we currently change the mac address inside the wpan interface while
we have a lowpan interface on top of the wpan interface, the mac address
setting doesn't reach the lowpan interface. The effect would be that the
IPv6 lowpan interface has the old SLAAC address and isn't working
anymore because the lowpan interface use in internal mechanism sometimes
dev->addr which is the old mac address of the wpan interface.

This patch checks if a wpan interface belongs to lowpan interface, if
yes then we need to check if the lowpan interface is down and change the
mac address also at the lowpan interface. When the lowpan interface will
be set up afterwards, it will use the correct SLAAC address which based
on the updated mac address setting.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Tested-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We currently supports multiple lowpan interfaces per wpan interface. I
never saw any use case into such functionality. We drop this feature now
because it's much easier do deal with address changes inside the under
laying wpan interface.

This patch removes the multiple lowpan interface and adds a lowpan_dev
netdev pointer into the wpan_dev, if this pointer isn't null the wpan
interface belongs to the assigned lowpan interface.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Tested-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The lowpan_fetch_skb function is used to fetch the first byte,
which also increments the data pointer in skb structure,
making subsequent array lookup of byte 0 actually being byte 1.

To decompress the first byte of the Flow Label when the TF flag is
set to 0x01, the second half of the first byte is needed.

The patch fixes the extraction of the Flow Label field.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Lukasz Duda <lukasz.duda@nordicsemi.no>
Signed-off-by: Glenn Ruben Bakke <glenn.ruben.bakke@nordicsemi.no>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We will not release sdio bus until firmware is completely
downloaded and becomes ready. Our 8887 A2 chip can have
separate firmware images for WLAN and bluetooth. This
patch fixes an issue observed when both drivers
simultaneously try to download respective firmwares.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We should be passing the pointer itself instead of the address of the
pointer.

This was a copy and paste bug when we replaced the calls to
hci_send_cmd().  Originally, the arguments were "len, cp" but we
overwrote them with "sizeof(cp), &cp" by mistake.

Fixes: b3d39140 ('Bluetooth: Move amp assoc read/write completed callback to amp.c')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Jiri Pirko says:

====================
mlxsw: Couple of fixes/adjustments

Ido Schimmel (5):
  mlxsw: Call free_netdev when removing port
  mlxsw: Make system port to local port mapping explicit
  mlxsw: Simplify mlxsw_sx_port_xmit function
  mlxsw: Use correct skb length when dumping payload
  mlxsw: Fix use-after-free bug in mlxsw_sx_port_xmit

Jiri Pirko (2):
  mlxsw: Make pci module dependent on HAS_DMA and HAS_IOMEM
  mlxsw: Strip FCS from incoming packets
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Store the length of the skb before transmitting it and use it for stats
instead of skb->len, since skb might have been freed already.

This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not use the length of the transmitted skb (which was freed), but
that of the response skb.

This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously we only checked if the transmission queue is not full in the
middle of the xmit function. This lead to complex logic due to the fact
that sometimes we need to reallocate the headroom for our Tx header.

Allow the switch driver to know if the transmission queue is not full
before sending the packet and remove this complex logic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FCS of incoming packets is already checked by HW. Just strip it out.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This resolves compile errors on um-allyesconfig.

Note that there are many other drivers which have the same issue.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

System ports are unique identifiers in a multi-ASIC environment that
represent all the available ports in the system. Local ports on the
other hand, are unique only within the local ASIC.

Since system port to local port mapping is not part of the HW-SW
contract and since only single-ASIC configurations are currently
supported, set an explicit 1:1 mapping by configuring the Switch System
Port Record (SSPR) register.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When removing a port's netdevice we should also free the memory
allocated by alloc_etherdev(). Do this by calling free_netdev() at the
end of the teardown sequence.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fix double word "the the" in
Documentation/DocBook/networking/API-eth-get-headlen.html
Documentation/DocBook/networking/netdev.html
Documentation/DocBook/networking.xml

These files are generated from comment in source,
so I have to fix comment in net/ethernet/eth.c.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>