GitLab

MSI doesn't work properly on resume on many platforms because the
BIOS goes and changes it back to INTx mode after the sky2 driver has
restored in resume.

It is really a bug in the base power management resume code, and
this workaround is temporary until the change to PM code works it's way
through the release process.  The PM fix is non-trivial since it needs
to change when non-boot CPU's are enabled.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Shutting down port 0 disables the NAPI poll used by both ports.
The long term fix will be to separate NAPI object from net device
until then just reenable if needed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

via-velocity doesn't build when CONFIG_INET=n:

drivers/built-in.o: In function `velocity_unregister_notifier':
via-velocity.c:(.text+0xe9b46): undefined reference to `unregister_inetaddr_notifier'
drivers/built-in.o: In function `velocity_init_module':
via-velocity.c:(.init.text+0xa027): undefined reference to `register_inetaddr_notifier'

I wanted to make this change in drivers/net/Kconfig, but
this isn't legal kconfig language:

 config VIA_VELOCITY
        tristate "VIA Velocity support"
        depends on NET_PCI && PCI
+       depends on INET if PM
        select CRC32
        select CRC_CCITT
        select MII

so fix it in via-velocity.c instead.
Builds with all 4 combinations of CONFIG_NET & CONFIG_PM.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The e1000 driver has a workaround for 82544 on PCI-X where if the
terminating byte of a buffer is at addresses 0-3 mod 8, then 4 bytes
are shaved off it and defered to a new segment.  This is due to an
erratum that could otherwise cause TX hangs.

Unfortunately this breaks TSO because it may cause the TCP header to
be split over two segments which itself causes TX hangs.  The solution
is to pull 4 bytes of data up from the next segment rather than pushing
4 bytes off.  This ensures the TCP header remains in one piece and
works around the PCI-X hang.

This patch is based on one from Jesse Brandeburg.

This bug has been trigered by both CONFIG_DEBUG_SLAB as well as Xen.

Note that the only reason we don't see this normally is because the
TCP stack starts writing from the end, i.e., it writes the TCP header
first then slaps on the IP header, etc.  So the end of the TCP header
(skb->tail - 1 here) is always aligned correctly.

Had we made the start of the IP header (e.g., IPv6) 8-byte aligned
instead, this would happen for normal TCP traffic as well.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
--
Visit Openswan at http://www.openswan.org/
Email: Herbert Xu ~{PmV>HI~} <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt


--
Signed-off-by: Jeff Garzik <jeff@garzik.org>

On suspend, handle pci_set_power_state errors, and on resume
handle failures in pci_resume_state().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The PCI MSI and express state are already saved and restored by the
current versions of pci_save_state/pci_restore_state.
Therefore it is no longer necessary for the driver to do it.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Now that IRQ are requested is called on open() and freed on close(),
we can safely switch from/to MSI without unloading the module.

We are guaranteed to correctly free IRQ even if the sysfs file got
written in the meantime since the MSI initialization is stored in
mgp->msi_enabled.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Request IRQ in myri10ge_open() and free in close() instead of probe()
and remove() to eliminate potential race between the watchdog and the
interrupt handler. Additionaly, the interrupt handler won't get called
on shared irq anymore when the interface is down.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Since pci_save_state() pushes MSI and PCIe states on a kind of stack,
myri10ge saving the state in advance for parity recovery will push the
state again on the stack on suspend. This leads to some memory leak.
We add a couple additional calls to save_state and restore_state so
that we don't leak anymore.

For the future, we are thinking of a better way to recover from parity
error without using pci_save_state().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The former option is removed and platform code can now specify the
expected behavior.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

net/core/netpoll.c::netpoll_send_skb() calls the poll handler when
it is available. As netconsole can be used from almost any context,
IRQ must not be enabled blindly in the NAPI handler of a driver which
supports netpoll.

b57bd066

 fixed the issue for the
8139too.c driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Currently after an interface up, the link state is detected 2 seconds later
when the first watchdog timer runs. This patch changes that by triggering
the hardware to generate a link-change interrupt from the up() function
instead. This has the result that the link state gets detected immediately
and without races. This has the potential to speed up booting since a normal
distribution boot process waits for a link before DHCP is attempted.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add 3 extra packet redirect counters for tracking purposes to make sure
we can test that all packets arrive properly.

Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>,
rewritten to use feature flags by me.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Allow the user to vary the size that copybreak works. Currently cb is enabled
for packets < 256 bytes, but various tests indicate that this should be
configurable for specific use cases. In addition, this parameter allows us
to force never/always during testing to get full and predictable coverage of
both code paths.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Assign the PBA to be large enough to contain at least 2 jumbo frames on
all adapters. This dramatically increases performance on several adapters
and fixes TX performance degradation issues where the PBA was misallocated
in the old algorithm.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

the driver has (ancient) code for messing with TIPG from the 82542 days.
Unfortunately this code was running on our current adapters and setting
TIPG for fiber to be +1 over the copper value.  This caused 1.45Mpps
to be sent instead of 1.487Mpps.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

For older adapters we know that they are of the PCI bus type, so we can
just set this.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This bugfix makes sure that the driver data reflects the full new situation
before the adapter is reinitialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

In rare occasions, ESB2 systems would end up started without the RX
unit being turned on. Add a check that runs post-init to work around
this issue.

Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>,
rewritten to use feature flags by me.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

CONFIG_DEBUG_SLAB changes alignments of the data structures the slab
allocators return. These break certain workarounds for TSO on the 82544.
Since DEBUG_SLAB is relatively rare and not used for performance sensitive
cases, the simplest fix is to disable TSO in this special situation.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

If the user has forced gigabit speed, phy power management must be disabled;
otherwise the NIC would try to negotiate to a linkspeed of 10/100 mbit on
shutdown, which would lead to a total loss of link. This loss of link breaks
Wake-on-Lan and IPMI.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Several bugs existed in how we handle manageability issues all
over the driver.  This patch consolidates all the managability
release and init code in two single functions and call them from
appropriate locations. This fixes several BMC packet redirect issues
and powerup/down hiccups.

Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>, rewritten
to use feature flags by me.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The 82543 chip does not count tx_carrier_errors properly in FD mode;
report zeros instead of garbage.

Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>, rewritten
to use feature flags by me.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Makes future changes a bit more readable.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The dynamic interrupt rate control patches omitted proper counting
for jumbo's and TSO resulting in suboptimal interrupt mitigation strategies.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The lower 2 bits of a user-supplied itr setting (via ethtool) need to be
masked off: These lower two bits are used as control bits.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This also adds he required page "writeback" flag handling, that cifs
hasn't been doing and that the page dirty flag changes made obvious.
Acked-by: Steve French <smfltc@us.ibm.com>
Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

We use the fixmap for accessing pci config space in pci_mmcfg_read/write().
The problem is in pci_exp_set_dev_base(). It is caching a last
accessed address to avoid calling set_fixmap_nocache() whenever
pci_mmcfg_read/write() is used.

  static inline void pci_exp_set_dev_base(int bus, int devfn)
  {
	u32 dev_base = base | (bus << 20) | (devfn << 12);
	if (dev_base != mmcfg_last_accessed_device) {
		mmcfg_last_accessed_device = dev_base;
		set_fixmap_nocache(FIX_PCIE_MCFG, dev_base);
	}
  }

            cpu0                                        cpu1
  ---------------------------------------------------------------------------
    pci_mmcfg_read("device-A")
        pci_exp_set_dev_base()
            set_fixmap_nocache()
                                              pci_mmcfg_read("device-B")
                                                  pci_exp_set_dev_base()
                                                      set_fixmap_nocache()
    pci_mmcfg_read("d...

Clark Williams reported that suspend doesnt work on his laptop on
2.6.20-rc1-rt kernels. The bug was introduced by the following cleanup
commit:

 commit 112cecb2


 Author: Siddha, Suresh B <suresh.b.siddha@intel.com>
 Date:   Wed Dec 6 20:34:31 2006 -0800

    [PATCH] suspend: don't change cpus_allowed for task initiating the suspend

because with this change 'error' is not initialized to 0 anymore, if
there are no other online CPUs. (i.e. if the system is single-CPU).

the fix is the initialize it to 0. The really weird thing is that my
version of gcc does not warn about this non-initialized variable
situation ...

(also fix the kernel printk in the error branch, it was missing a
 newline)
Reported-by: Clark Williams <williams@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Thanks to Len Brown for testing this fix, since while they have in the
past, none of my machines run reiserfs at the moment.

Cc: Vladimir V. Saveliev <vs@namesys.com>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Make cancel_dirty_page() act more like all the other dirty and writeback
accounting functions: test for "mapping" being NULL, and do the
NR_FILE_DIRY accounting purely based on mapping_cap_account_dirty()).

Also, add it to the exports, so that modular filesystems can use it.
Acked-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (68 commits)
  ACPI: replace kmalloc+memset with kzalloc
  ACPI: Add support for acpi_load_table/acpi_unload_table_id
  fbdev: update after backlight argument change
  ACPI: video: Add dev argument for backlight_device_register
  ACPI: Implement acpi_video_get_next_level()
  ACPI: Kconfig - depend on PM rather than selecting it
  ACPI: fix NULL check in drivers/acpi/osl.c
  ACPI: make drivers/acpi/ec.c:ec_ecdt static
  ACPI: prevent processor module from loading on failures
  ACPI: fix single linked list manipulation
  ACPI: ibm_acpi: allow clean removal
  ACPI: fix git automerge failure
  ACPI: ibm_acpi: respond to workqueue update
  ACPI: dock: add uevent to indicate change in device status
  ACPI: ec: Lindent once again
  ACPI: ec: Change #define to enums there possible.
  ACPI: ec: Style changes.
  ACPI: ec: Acquire Global Lock under EC mutex.
  ACPI: ec: Drop udelay() from poll mode. Loop by reading status field instead.
  ACPI: ec: Rename gpe_bit to gpe
  ...

The function isdn_ppp_ccp_reset_alloc_state() sets ->timer.function
and ->timer.data and later on calls add_timer() with no init_timer()
ever done.

Noted by Al Viro.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [UDP]: Fix reversed logic in udp_get_port().
  [IPV6]: Dumb typo in generic csum_ipv6_magic()
  [SCTP]: make 2 functions static
  [SCTP]: Fix typo adaption -> adaptation as per the latest API draft.
  [SCTP]: Don't export include/linux/sctp.h to userspace.
  [TCP]: Fix ambiguity in the `before' relation.
  [ATM] drivers/atm/fore200e.c: Cleanups.
  [ATM]: Remove dead ATM_TNETA1570 option.
  NetLabel: correctly fill in unused CIPSOv4 level and category mappings
  NetLabel: perform input validation earlier on CIPSOv4 DOI add ops

The logic in cfq_allow_merge() wasn't clear enough - basically allow
merging for the same queues only.  Do a fast check for 'rq and bio both
sync/async' before doing the cfqq hash lookup.

This is verified to work with the fixed elv_try_merge() from commit
bb4067e3

.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

When this code was converted to use sk_for_each() the
logic for the "best hash chain length" code was reversed,
breaking everything.

The original code was of the form:

			size = 0;
			do {
				if (++size >= best_size_so_far)
					goto next;
			} while ((sk = sk->next) != NULL);
			best_size_so_far = size;
			best = result;
		next:;

and this got converted into:

			sk_for_each(sk2, node, head)
				if (++size < best_size_so_far) {
					best_size_so_far = size;
					best = result;
				}

Which does something very very different from the original.
Signed-off-by: David S. Miller <davem@davemloft.net>

... duh
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes the following needlessly global functions static:
- ipv6.c: sctp_inet6addr_event()
- protocol.c: sctp_inetaddr_event()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ivan Skytte Jorgensen <isj-sctp@i1.dk>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>