When the bound device of a tunnel device is down, encapsulated packets
are not egressed anymore, but tunnel decap still works. Extend
mlxsw_sp_nexthop_rif_update() to take IFF_UP into consideration when
deciding whether a given next hop should be offloaded.

Because the new logic was added to mlxsw_sp_nexthop_rif_update(), this
fixes the case where a newly-added tunnel has a down bound device, which
would previously be fully offloaded. Now the down state of the bound
device is noted and next hops forwarding to such tunnel are not
offloaded.

In addition to that, notice NETDEV_UP and NETDEV_DOWN of a bound device
to force refresh of tunnel encap route offloads.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a bound device of an IP-in-IP tunnel changes, such as through
'ip tunnel change name $name dev $dev', the loopback backing the tunnel
needs to be recreated.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes to L3 tunnel netdevices (through `ip tunnel change' as well as
`ip link set') lead to NETDEV_CHANGE being generated on the tunnel
device. Because what is relevant for the tunnel in question depends on
the tunnel type, handling of the event is dispatched to the IPIP module
through a newly-added interface mlxsw_sp_ipip_ops.ol_netdev_change().

IPIP tunnels now remember the last set of tunnel parameters in struct
mlxsw_sp_ipip_entry.parms, and use it to figure out what exactly has
changed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a bound device of a tunnel netdevice changes VRF, the loopback RIF
that backs the tunnel needs to be updated and existing encapsulating
routes need to be refreshed.

Note that several tunnels can share the same bound device, in which case
all the impacted tunnels need to be updated.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The approach for offloading IP tunnels implemented currently by mlxsw
doesn't allow two tunnels that have the same local IP address in the
same (underlay) VRF. Previously, offloads were introduced on demand as
encap routes were formed. When such a route was created that would cause
offload of a conflicting tunnel, mlxsw_sp_ipip_entry_create() would
detect it and return -EEXIST, which would propagate up and cause FIB
abort.

Now however IPIP entries are created as soon as an offloadable netdevice
is created, and the failure prevents creation of such device.
Furthermore, if the driver is installed at the point where such
conflicting tunnels exist, the failure actually prevents successful
modprobe.

Furthermore, follow-up patches implement handling of NETDEV_CHANGE due
to the local address change. However, NETDEV_CHANGE can't be vetoed. The
failure merely means that the offloads weren't updated, but the change
in Linux configuration is not rolled back. It is thus desirable to have
a robust way of handling these conflicts, which can later be reused for
handling NETDEV_CHANGE as well.

To fix this, when a conflicting tunnel is created, instead of failing,
simply pull the old tunnel to slow path and reject offloading the
new one.

Introduce two functions: mlxsw_sp_ipip_entry_demote_tunnel() and
mlxsw_sp_ipip_demote_tunnel_by_saddr() to handle this. Make them both
public, because they will be useful later on in this patchset.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When trying to determine whether there are other offloaded tunnels with
the same local address, mlxsw_sp_ipip_entry_create() should look for a
tunnel with matching UL protocol, matching saddr, in the same VRF.
However instead of taking into account the UL protocol of the tunnel
netdevice (which mlxsw_sp_ipip_entry_saddr_matches() then compares to
the UL protocol of inspected IPIP entry), it deduces the UL protocol
from the inspected IPIP entry (and that's compared to itself).

This is currently immaterial, because only one tunnel type is offloaded,
and therefore the UL protocol always matches, but introducing support
for a tunnel with IPv6 underlay would uncover this error.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The work that needs to be done to update HW configuration in response to
changes is similar to what __mlxsw_sp_ipip_entry_update_tunnel() already
does, but with a number of twists: each change requires a different
subset of things to happen. Extend the function to support all these
uses, and allow finely-grained configuration of what should happen at
each call through a suite of function arguments.

Publish the updated function to allow use from the spectrum_ipip module.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The work that's done by mlxsw_sp_netdevice_ipip_ol_vrf_event() is a good
basis for a more versatile function that would take care of all sorts of
tunnel updates requests: __mlxsw_sp_ipip_entry_update_tunnel(). Extract
that function. Factor out a helper mlxsw_sp_ipip_entry_ol_lb_update() as
well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function mlxsw_sp_rif_create() takes an extack parameter. So far,
for creation of loopback interfaces, NULL was passed. For some events
however the extack can be extracted and passed along. So do that for
NETDEV_CHANGEUPPER handler.

Use the opportunity to update the type of info argument that
mlxsw_sp_netdevice_ipip_ol_event() takes. Follow-up patches will
introduce handling of more changes, and some of them carry an extack as
well, but in an info structure of a different type. Though not strictly
erroneous (the pointer could be cast whichever way), it makes no sense
to pretend the value is always of a certain type, when in fact it isn't.
So change the prototype of the above-mentioned function as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The piece of logic to promote decap route, if any, is useful for generic
tunnel updates, not just for handling of NETDEV_UP events on tunnel
interfaces. Extract it to a separate function.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function only ever returns 0, so don't pretend it returns anything
useful and just make it void.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To implement NETDEV_CHANGE notifications on IP-in-IP tunnels, the
handler needs to figure out what actually changed, to understand how
exactly to update the offloads. It will do so by storing struct
ip_tunnel_parm with previous configuration, and comparing that to the
new version.

To facilitate these comparisons, extract the code that operates on
struct ip_tunnel_parm from the existing accessor functions, and make
those a thin wrapper that extracts tunnel parameters and dispatches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These functions ideologically belong to the IPIP module, and some
follow-up work will benefit from their presence there.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of the code down the road needs this logic as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To distinguish between events related to tunnel device itself and its
bound device, rename a number of functions related to handling tunneling
netdevice events to include _ol_ (for "overlay") in the name. That
leaves room in the namespace for underlay-related functions, which would
have _ul_ in the name.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
net: core: introduce mini_Qdisc and eliminate usage of tp->q for clsact fastpath

This patchset's main patch is patch number 2. It carries the
description. Patch 1 is just a dependency.

---
v3->v4:
- rebased to be applicable on top of the current net-next
v2->v3:
- Using head change callback to replace miniq pointer every time tp head
  changes. This eliminates one rcu dereference and makes the claim "without
  added overhead" valid.
v1->v2:
- Use dev instead of skb->dev in sch_handle_egress as pointed out by Daniel
- Fixed synchronize_rcu_bh() in mini_qdisc_disable and commented
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In sch_handle_egress and sch_handle_ingress tp->q is used only in order
to update stats. So stats and filter list are the only things that are
needed in clsact qdisc fastpath processing. Introduce new mini_Qdisc
struct to hold those items. Also, introduce a helper to swap the
mini_Qdisc structures in case filter list head changes.

This removes need for tp->q usage without added overhead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a callback that is to be called whenever head of the chain changes.
Also provide a callback for the default case when the caller gets a
block using non-extended getter.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lipeng says:

====================
net: hns3: support set_link_ksettings and for nway_reset ethtool command

This patch-set adds support for set_link_ksettings && for nway_resets
ethtool command and fixes some related ethtool bugs.
1, patch[4/6] adds support for ethtool_ops.set_link_ksettings.
2, patch[5/6] adds support ethtool_ops.for nway_reset.
3, patch[1/6,2/6,3/6,6/6] fix some bugs for getting port information by
   ethtool command(ethtool ethx).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a bug for phy supported feature initialization.
Currently, the value of phydev->supported is initialized by kernel.
So it includes many features that we do not support, such as
SUPPORTED_FIBRE and SUPPORTED_BNC. This patch fixes it.

Fixes: 256727da (net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds nway_reset support for ethtool cmd.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds set_link_ksettings support for ethtool cmd.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The value of link_modes.advertising and the value of link_modes.supported
is initialized to zero every time in for loop in hns3_driv_to_eth_caps().
But we just want to set specified bit for them. Initialization is
unnecessary. This patch fixes it.

Fixes: 496d03e9 (net: hns3: Add Ethtool support to HNS3 driver)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a bug for ethtool's get_link_ksettings().
The advertising for autoneg is always added to advertised_caps
whether autoneg is enable or disable. This patch fixes it.

Fixes: 496d03e9 (net: hns3: Add Ethtool support to HNS3 driver)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a bug for ethtool's get_link_ksettings().
When phy exists, we should get autoneg from phy rather than from mac.
Because the value of mac.autoneg is invalid when phy exists.

Fixes: 496d03e9 (net: hns3: Add Ethtool support to HNS3 driver)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Fix IRQ coalescing regressions.

There was a typo and missing guard-rail against illegal values in the
recent code clean up.  All reported by Andy Gospodarek.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent IRQ coalescing clean up has removed a guard-rail for the max DMA
buffer coalescing value.  This is a 6-bit value and must not be 0.  We
already have a check for 0 but 64 is equivalent to 0 and will cause
non-stop interrupts.  Fix it by adding the proper check.

Fixes: f8503969 ("bnxt_en: Refactor and simplify coalescing code.")
Reported-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent refactoring of coalesce settings contained a typo that prevents
receive settings from being set properly.

Fixes: 18775aa8 ("bnxt_en: Reorganize the coalescing parameters.")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Callers of tcf_block_put() could pass NULL so
we can't use block->q before checking if block is
NULL or not.

tcf_block_put_ext() callers are fine, it is always
non-NULL.

Fixes: 8c4083b3 ("net: sched: add block bind/unbind notif. and extended block_get/put")
Reported-by: Dave Taht <dave.taht@gmail.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While stress testing MTU probing, we had crashes in list_del() that we root-caused
to the fact that tcp_fragment() is unconditionally inserting the freshly allocated
skb into tsorted_sent_queue list.

But this list is supposed to contain skbs that were sent.
This was mostly harmless until MTU probing was enabled.

Fortunately we can use the tcp_queue enum added later (but in same linux version)
for rtx-rb-tree to fix the bug.

Fixes: e2080072 ("tcp: new list for sent but unacked skbs for RACK recovery")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Priyaranjan Jha <priyarjha@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Geliang Tang <geliangtang@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 114780
Addresses-Coverity-ID: 114781
Addresses-Coverity-ID: 114782
Addresses-Coverity-ID: 114783
Addresses-Coverity-ID: 114784
Addresses-Coverity-ID: 114785
Addresses-Coverity-ID: 114786
Addresses-Coverity-ID: 114787
Addresses-Coverity-ID: 114788
Addresses-Coverity-ID: 114789
Addresses-Coverity-ID: 114790
Addresses-Coverity-ID: 114791
Addresses-Coverity-ID: 114792
Addresses-Coverity-ID: 114793
Addresses-Coverity-ID: 114794
Addresses-Coverity-ID: 114795
Addresses-Coverity-ID: 200521
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently gen_flags is being operated on by a logical && operator rather
than a bitwise & operator. This looks incorrect as these should be bit
flag operations. Fix this.

Detected by CoverityScan, CID#1460305 ("Logical vs. bitwise operator")

Fixes: 3f7889c4 ("net: sched: cls_bpf: call block callbacks for offload)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

icsk_accept_queue.fastopenq.lock is only fully initialized at listen()
time.

LOCKDEP is not happy if we attempt a spin_lock_bh() on it, because
of missing annotation. (Although kernel runs just fine)

Lets use net->ipv4.tcp_fastopen_ctx_lock to protect ctx access.

Fixes: 1fba70e5 ("tcp: socket option to set TCP fast open key")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

do_check() can fail early without allocating env->cur_state under
memory pressure.  Syzkaller found the stack below on the linux-next
tree because of this.

  kasan: CONFIG_KASAN_INLINE enabled
  kasan: GPF could be caused by NULL-ptr deref or user memory access
  general protection fault: 0000 [#1] SMP KASAN
  Dumping ftrace buffer:
     (ftrace buffer empty)
  Modules linked in:
  CPU: 1 PID: 27062 Comm: syz-executor5 Not tainted 4.14.0-rc7+ #106
  Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
  task: ffff8801c2c74700 task.stack: ffff8801c3e28000
  RIP: 0010:free_verifier_state kernel/bpf/verifier.c:347 [inline]
  RIP: 0010:bpf_check+0xcf4/0x19c0 kernel/bpf/verifier.c:4533
  RSP: 0018:ffff8801c3e2f5c8 EFLAGS: 00010202
  RAX: dffffc0000000000 RBX: 00000000fffffff4 RCX: 0000000000000000
  RDX: 0000000000000070 RSI: ffffffff817d5aa9 RDI: 0000000000000380
  RBP: ffff8801c3e2f668 R08: 0000000000000000 R09: 1ffff100387c5d9f
  R10: 00000000218c4e80 R11: ffffffff85b34380 R12: ffff8801c4dc6a28
  R13: 0000000000000000 R14: ffff8801c4dc6a00 R15: ffff8801c4dc6a20
  FS:  00007f311079b700(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00000000004d4a24 CR3: 00000001cbcd0000 CR4: 00000000001406e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   bpf_prog_load+0xcbb/0x18e0 kernel/bpf/syscall.c:1166
   SYSC_bpf kernel/bpf/syscall.c:1690 [inline]
   SyS_bpf+0xae9/0x4620 kernel/bpf/syscall.c:1652
   entry_SYSCALL_64_fastpath+0x1f/0xbe
  RIP: 0033:0x452869
  RSP: 002b:00007f311079abe8 EFLAGS: 00000212 ORIG_RAX: 0000000000000141
  RAX: ffffffffffffffda RBX: 0000000000758020 RCX: 0000000000452869
  RDX: 0000000000000030 RSI: 0000000020168000 RDI: 0000000000000005
  RBP: 00007f311079aa20 R08: 0000000000000000 R09: 0000000000000000
  R10: 0000000000000000 R11: 0000000000000212 R12: 00000000004b7550
  R13: 00007f311079ab58 R14: 00000000004b7560 R15: 0000000000000000
  Code: df 48 c1 ea 03 80 3c 02 00 0f 85 e6 0b 00 00 4d 8b 6e 20 48 b8 00 00 00 00 00 fc ff df 49 8d bd 80 03 00 00 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 b6 0b 00 00 49 8b bd 80 03 00 00 e8 d6 0c 26
  RIP: free_verifier_state kernel/bpf/verifier.c:347 [inline] RSP: ffff8801c3e2f5c8
  RIP: bpf_check+0xcf4/0x19c0 kernel/bpf/verifier.c:4533 RSP: ffff8801c3e2f5c8
  ---[ end trace c8d37f339dc64004 ]---

Fixes: 638f5b90 ("bpf: reduce verifier memory consumption")
Fixes: 1969db47 ("bpf: fix verifier memory leaks")
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The neighbor monitor employs a threshold, default set to 32 peer nodes,
where it activates the "Overlapping Neighbor Monitoring" algorithm.
Below that threshold, monitoring is full-mesh, and no "domain records"
are passed between the nodes.

Because of this, a node never received a peer's ack that it has received
the most recent update of the own domain. Hence, the field 'acked_gen'
in struct tipc_monitor_state remains permamently at zero, whereas the
own domain generation is incremented for each added or removed peer.

This has the effect that the function tipc_mon_get_state() always sets
the field 'probing' in struct tipc_monitor_state true, again leading the
tipc_link_timeout() of the link in question to always send out a probe,
even when link->silent_intv_count is zero.

This is functionally harmless, but leads to some unncessary probing,
which can easily be eliminated by setting the 'probing' field of the
said struct correctly in such cases.

At the same time, we explictly invalidate the sent domain records when
the algorithm is not activated. This will eliminate any risk that an
invalid domain record might be inadverently accepted by the peer.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the offload unbind is done before the chains are flushed.
That causes driver to unregister block callback before it can get all
the callback calls done during flush, leaving the offloaded tps inside
the HW. So fix the order to prevent this situation and restore the
original behaviour.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Reported-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to new ethtool operation get_fecparam to
fetch FEC parameters.

Original Work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 0x6086 T6 device id.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>