- 29 Jun, 2017 27 commits
-
-
Lendacky, Thomas authored
When I2C communication fails, it tends to always fail. Rather than continuously issue an error message (once per second in most cases), change the message to be issued just once. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
The driver has some missing functionality when operating in the mode that supports 2.5GbE. Fix the driver to fully recognize and support this speed. Signed-off-by:
-
Lendacky, Thomas authored
Currently the function that performs a software reset of the hardware provides a return code. During driver probe check this return code and exit with an error if the software reset fails. Signed-off-by:
-
Lendacky, Thomas authored
Just to be on the safe side, should the update of the timestamp registers not complete, issue a warning rather than looping forever waiting for the update to complete. Signed-off-by:
-
Lendacky, Thomas authored
Spurious Tx timestamp interrupts can cause an oops in the Tx timestamp processing function if a Tx timestamp skb is NULL. Add a check to insure a Tx timestamp skb is present before attempting to use it. Signed-off-by:
-
Lendacky, Thomas authored
During PTP initialization, the Timestamp Control register should be cleared and not the Tx Configuration register. While this typo causes the wrong register to be cleared, the default value of each register and and the fact that the Tx Configuration register is programmed afterwards doesn't result in a bug, hence only fixing in net-next. Signed-off-by:
-
Lendacky, Thomas authored
When using SFPs, the supported and advertised settings should be initially based on the SFP that has been detected. The code currently indicates the overall support of the device as opposed to what the SFP is capable of. Update the code to change the supported link modes, auto-negotiation, etc. to be based on the installed SFP. Signed-off-by:
-
Lendacky, Thomas authored
Simplify and centralize the mailbox command rate change interface by having a single function perform the writes to the mailbox registers to issue the request. Signed-off-by:
-
David S. Miller authored
Martin KaFai Lau says: ==================== bpf: Add syscall lookup support for fd array and htab This patchset adds BPF_MAP_LOOKUP_ELEM syscall support for BPF_MAP_TYPE_PROG_ARRAY, BPF_MAP_TYPE_ARRAY_OF_MAPS and BPF_MAP_TYPE_HASH_OF_MAPS ==================== Reviewed-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
-
Martin KaFai Lau authored
Checks are added to the existing sockex3 and test_map_in_map test. Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Martin KaFai Lau authored
This patch allows userspace to do BPF_MAP_LOOKUP_ELEM on BPF_MAP_TYPE_PROG_ARRAY, BPF_MAP_TYPE_ARRAY_OF_MAPS and BPF_MAP_TYPE_HASH_OF_MAPS. The lookup returns a prog-id or map-id to the userspace. The userspace can then use the BPF_PROG_GET_FD_BY_ID or BPF_MAP_GET_FD_BY_ID to get a fd. Signed-off-by:
-
Thor Thayer authored
Version 3.70a of the Designware has additional DMA registers so add those to the ethtool DMA Register dump. Offset 9 - Receive Interrupt Watchdog Timer Register Offset 10 - AXI Bus Mode Register Offset 11 - AHB or AXI Status Register Offset 22 - HW Feature Register Signed-off-by:
Thor Thayer <thor.thayer@linux.intel.com> Acked-by:
Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5-updates-2017-06-27 (Innova IPsec offload support) This patchset adds support for Innova IPSec network interface card. About Innova device: -------------------- Innova is a network card with a ConnectX chip and an FPGA chip as a bump-on-the-wire. Internal +----------+ Link +-----------------+ | +--------------+ FPGA | +------+ | ConnectX | | Shell +--+ QSFP | | +--------------+ +-------+ | | Port | +----------+ I2C | | SBU | | +------+ | +-------+ | +--+----------+---+ | | +--+--+ +---+---+ | DDR | | Flash | +-----+ +-------+ The FPGA synthesized logic is loaded from dedicated flash storage and has access to its own dedicated DDR RAM. The ConnectX chip firmware programs the FPGA by accessing its configuration space over either the slow internal I2C link or the high-speed internal link. The FPGA logic is divided into a "Shell" and a "Sandbox Unit" (SBU). mlx5_core driver (with CONFIG_MLX5_FPGA) handles all shell functionality, while other components may handle the various SBU functionalities. The driver opens high-speed reliable communication channels with the shell and the SBU over the internal link. These channels may be used for high-bandwidth configuration or for SBU-specific out-of-band data paths. About Innova IPSec device: -------------------------- Innova IPSec is a network card that allows offloading IPSec cryptography operations from the host CPU to the NIC. It is an Innova card with an IPSec SBU. The hardware keeps the database of IPSec Security Associations (SADB) in the FPGA's DDR memory. Internal +----------+ Link +-----------------+ | +--------------+ FPGA | +------+ | ConnectX | | Shell +--+ QSFP | | +--------------+ +-------+ | | Port | +----------+ Internal I2C | | IPSec | | +------+ | | SBU | | | +-------+ | +--+----------+---+ | | +--+--+ +---+---+ | DDR | | | | | | Flash | |SADB | | | +-----+ +-------+ Modes and ciphers: Currently the following modes and ciphers are supported: IPv4 and IPv6 ESP tunnel and transport modes AES 128 and 256 bit encryption, with GCM authentication (RFC4106) IV is generated using seqiv, in sync with Linux's geniv. More modes and ciphers may be added later. Notes: In the future similar functionality will be included in a single-chip NIC. About the driver: ----------------- Patches 1-4 prepare some existing driver code for the new feature: * Add support for reserved GIDs in the hardware GID table * Allow multiple modules to enable hardware RoCE support independently Patches 5-6 define structs and helper functions for QP work-queues. Patches 7-11 add various FPGA-related features required for Innova. IPSec. Patch 12 adds abstraction layer for Mellanox IPSec-offload capable devices. atches 13-16 add IPSec offload support to the mlx5 netdevice. This driver services the new IPSec offload API introduced in commit d77e38e6 ("xfrm: Add an IPsec hardware offloading API") Configuration Path: If Innova IPSec device is detected, the mlx5e netdevice gets the new NETIF_F_HW_ESP feature and the xdo callbacks, indicating ESP offload capabilities, and also the matching TX checksum and GSO features. The driver configures offloaded Security Associations (SAs) by sending an ADD_SA or DEL_SA message to the IPSec SBU, which updates the SADB in DDR. These messages and their responses are sent over a high-speed channel. Counters for ethtool are retrieved by the driver from the SBU. Data path: On receive path, the SBU decrypts ESP packets which match the offloaded SADB, but keeps them encapsulated. The SBU injects metadata (Mellanox owned ethertype) indicating that crypto-offload has taken place, the SA with which it was done, and the authentication result. The ConnectX chip performs RX checksum offload on the packet, and RSS using the ESP SPI value. The driver detects the special ethertype, and attaches a struct secpath to the RX SKB, including flags to indicate that crypto offload took place, the authentication result, and which xfrm_state was used for decryption, in the olen and ovec members. The RX SKB may have useful CHECKSUM_COMPLETE. A separate patchset will add support for that in the xfrm stack. On transmit path, the stack encapsulates the packet but does not encrypt it, and indicates in the SKB's secpath that crypto offload is to be performed and the SA to use to do so. The driver avoids performing crypto-offload for ESP fragments, and packets with IP options, as the SBU cannot currently do that. For eligible packets, the driver prepends a special ethertype with metadata instructing the hardware to perform crypto offload. The stack builds regular (non-GSO) SKBs so that they contain a placeholder for the ESP trailer. The driver trims it off, because the SBU automatically appends the trailer for offloaded packets. The ConnectX chip performs TX checksum offload on inner UDP or TCP packets, and GSO for TCP packets (duplicating the prepended metadata). The segmented packets then undergo encryption in the SBU before going on the wire. Performance: We measure single stream of TCP on Intel(R) Xeon(R) CPU E5-2643 v2 @3.50GHz Using AES-NI with ESP GSO we get constant 4.1 Gbps. Using crypto offload we get constant 18 Gbps. Note that these numbers require CHECKSUM_COMPLETE support in XFRM, which we submit separately. - Ilan Tayari ==================== Signed-off-by: -
David S. Miller authored
Ivan Khoronzhuk says: ==================== net: fix sw timestamping for non PTP packets This series contains several corrections connected with timestamping for cpsw and netcp drivers based on same cpts module. Based on net/next ==================== Reviewed-by:
-
Ivan Khoronzhuk authored
There is cpts function to check if packet can be timstamped with cpts. Seems that ptp_classify_raw cover all cases listed with "case". Signed-off-by:
Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by:
-
Ivan Khoronzhuk authored
The cpts can timestmap only ptp packets at this moment, so driver cannot mark every packet as though it's going to be timestamped, only because h/w timestamping for given skb is enabled with SKBTX_HW_TSTAMP. It doesn't allow to use sw timestamping, as result outgoing packet is not timestamped at all if it's not PTP and h/w timestamping is enabled. So, fix it by setting SKBTX_IN_PROGRESS only for PTP packets. Signed-off-by:
-
Ivan Khoronzhuk authored
Move sw timestamp function close to channel submit function. Signed-off-by:
-
Joe Perches authored
Using netdev_<level>(netdev, "%s: ...", netdev->name) duplicates the name in the output. Remove those uses. Miscellanea: o Use the netif_<level> convenience macros at the same time Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in mlx4_dbg debug message Signed-off-by:
Colin Ian King <colin.king@canonical.com> Acked-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in netif_info message Signed-off-by:
-
LABBE Corentin authored
Since the PHY used is internal, simply set phy-mode as internal. Signed-off-by:
Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by:
-
LABBE Corentin authored
Since the PHY used is internal, simply set phy-mode as internal. Signed-off-by:
-
LABBE Corentin authored
Since the PHY used is internal, simply set phy-mode as internal. Signed-off-by:
-
LABBE Corentin authored
Since the PHY used is internal, simply set phy-mode as internal. Signed-off-by:
-
LABBE Corentin authored
Since the PHY used is internal, simply set phy-mode as internal. Signed-off-by:
-
LABBE Corentin authored
The current way to find if the phy is internal is to compare DT phy-mode and emac_variant/internal_phy. But it will negate a possible future SoC where an external PHY use the same phy mode than the internal one. By using phy-mode = "internal" we permit to have an external PHY with the same mode than the internal one. Reported-by:
André Przywara <andre.przywara@arm.com> Signed-off-by:
-
Michael Dilmore authored
The bond_options.c file contains multiple netdev_info statements that clutter kernel output. This patch replaces all netdev_info with netdev_dbg and adds a netdev_dbg statement for the packets per slave parameter. Also fixes misalignment at line 467. Suggested-by:
Michael J Dilmore <michael.j.dilmore@gmail.com> Signed-off-by:
-
- 27 Jun, 2017 13 commits
-
-
David S. Miller authored
Jakub Kicinski says: ==================== nfp: get_phys_port_name for representors and SR-IOV reorder This series starts by making the error message if FW cannot be located easier to understand. Then I move some functions from PCI probe files into library code (nfpcore) where they belong, and remove one function which is never used. Next few patches equip representors with nfp_port structure and make their NDOs fully shared (not defined in apps), thanks to which we can easily determine which netdevs are NFP's by comparing the NDO pointers. 10th patch makes use of the shared NDOs and nfp_ports to deliver netdev-type independent .ndo_get_phys_port_name() implementation. Patches 11 and 12 reorder the nfp_app SR-IOV callbacks with enabling SR-IOV VFs. Unfortunately due to how PCI subsystem works we can't guarantee being able to disable SR-IOV at exit or that it will be disabled when we first probe... We must therefore make sure FW is able to deal with being loaded while SR-IOV is already on. Patch 13 fixes potential deadlock when enabling SR-IOV happens at the same time as port state refresh. Note that this can't happen at this point, since Flower doesn't refresh ports... but lockdep doesn't know about such details and we will have to deal with this sooner or later anyway. Last but not least a new Kconfig is added to make sure those who don't care about flower offloads have a way of not including the code in their kernels. Thanks to nfp_app separation this costs us a single ifdef and excluding flower files from the build. ==================== Signed-off-by: -
Jakub Kicinski authored
Give users an option not to build the flower-offload related code. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
Jakub Kicinski authored
Since we grab pf->lock around pci_enable_sriov() we can no longer safely queue work which may also grab that lock onto system workqueue. pci_enable_sriov() will flush system workqueue as part to wait for VF probing. Signed-off-by:
-
Jakub Kicinski authored
We previously assumed that app callback can be guaranteed to be executed before SR-IOV is actually enabled. Given that we can't guarantee that SR-IOV will be disabled during probe or that we will be able to disable it on remove, we should reorder the callbacks. We should also call the app's sriov_enable if SR-IOV was enabled during probe. Application FW must be able to disable VFs internally and not depend on them being removed at PCIe level. Signed-off-by:
-
Jakub Kicinski authored
We assumed that when we probe number of enabled VFs will be at 0. This doesn't have to be the case for example if previous driver left SR-IOV enabled due to some VFs being assigned. Read the number of VFs enabled. Fail probe if it's above current FWs limit. Signed-off-by:
-
Jakub Kicinski authored
Make nfp_port_get_phys_port_name() support new port types and wire it up to representors' struct net_device_ops. Signed-off-by:
-
Jakub Kicinski authored
Based on struct net_device_ops figure out if netdev is a nfp_repr. Use this knowledge to convert netdev directly to nfp_port. Signed-off-by:
-
Jakub Kicinski authored
Apps shouldn't declare their own struct net_device_ops for representors, this makes sharing code harder. Add necessary nfp_app callbacks and move the definition of representors' struct net_device_ops to common code. Signed-off-by:
-
Jakub Kicinski authored
Thanks to the fact that all representors will now have an nfp_port, we can depend on information there to provide a app-independent .ndo_get_stats64(). Signed-off-by:
-
Jakub Kicinski authored
nfp_port is an abstraction which is supposed to allow us sharing code between different netdev types (vNIC vs repr). Spawn ports for PFs and VFs to enable this sharing. Signed-off-by:
-
Jakub Kicinski authored
Add a cleanup callback for undoing what app init callback did. Make flower allocate its private structure on init and free it from the new callback. While at it remember to set the app pointer to NULL on the error path to avoid any races while probe path unwinds. Signed-off-by:
-
Jakub Kicinski authored
Remove unused nfp_cpp_area_check_range() function. Signed-off-by:
-
Jakub Kicinski authored
Move most of the helper for mapping RTsyms from nfp_net_main.c to nfpcore. Use the new helper directly for mapping MAC statistics, since they don't need to include the PCIe interface ID in the symbol name. Signed-off-by:
-
