In case of line card implementation, the core has to have a way to
remove relevant ports manually. Extend the Spectrum driver ops by an op
that implements port removal of selected ports upon request.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow to process events generated upon line card getting "ready" and
"active".

When DSDSC event with "ready" bit set is delivered, that means the
line card is powered up. Use MDDC register to push the line card to
active state. Once FW is done with that, the DSDSC event with "active"
bit set is delivered.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce objects for line cards and an infrastructure around that.
Use devlink_linecard_create/destroy() to register the line card with
devlink core. Implement provisioning ops with a list of supported
line cards.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MBCT register allows to transfer binary INI codes from the host to
the management FW by transferring it by chunks of maximum 1KB.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MDDC register allows to control downstream devices and line cards.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MDDQ register allows to query the DownStream device properties.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Register PMLPE trap and process the port mapping changes delivered
by it by creating related ports. Note that this happens after
provisioning. The INI of the linecard is processed and merged by FW.
PMLPE is generated for each port. Process this mapping change.

Layout of PMLPE is the same as layout of PMLP.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to hold the lock for alloc and freecpu. So narrow the critical
section. Follow-up patch is going to benefit from this by adding more
code to the functions which will be out of the critical as well.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PMECR register is used to enable/disable event triggering
in case of local port mapping change.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of array of pointers to port mapping structures, allocate the
array of structures directly.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far, the lane index always started from zero. That is not true for
modular systems with gearbox-equipped linecards. Loose the check so the
lanes can start from non-zero index.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to properly inform user about relationship between port and
line card, introduce a driver API to set line card for a port. Use this
information to extend port devlink netlink message by line card index
and also include the line card index into phys_port_name and by that
into a netdevice name.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow driver to mark a line card as active. Expose this state to the
userspace over devlink netlink interface with proper notifications.
'active' state means that line card was plugged in after
being provisioned.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to be able to configure all needed stuff on a port/netdevice
of a line card without the line card being present, introduce line card
provisioning. Basically by setting a type, provisioning process will
start and driver is supposed to create a placeholder for instances
(ports/netdevices) for a line card type.

Allow the user to query the supported line card types over line card
get command. Then implement two netlink command SET to allow user to
set/unset the card type.

On the driver API side, add provision/unprovision ops and supported
types array to be advertised. Upon provision op call, the driver should
take care of creating the instances for the particular line card type.
Introduce provision_set/clear() functions to be called by the driver
once the provisioning/unprovisioning is done on its side. These helpers
are not to be called directly due to the async nature of provisioning.

Example:
$ devlink port # No ports are listed
$ devlink lc
pci/0000:01:00.0:
  lc 1 state unprovisioned
    supported_types:
       16x100G
  lc 2 state unprovisioned
    supported_types:
       16x100G
  lc 3 state unprovisioned
    supported_types:
       16x100G
  lc 4 state unprovisioned
    supported_types:
       16x100G
  lc 5 state unprovisioned
    supported_types:
       16x100G
  lc 6 state unprovisioned
    supported_types:
       16x100G
  lc 7 state unprovisioned
    supported_types:
       16x100G
  lc 8 state unprovisioned
    supported_types:
       16x100G

$ devlink lc set pci/0000:01:00.0 lc 8 type 16x100G
$ devlink lc show pci/0000:01:00.0 lc 8
pci/0000:01:00.0:
  lc 8 state active type 16x100G
    supported_types:
       16x100G
$ devlink port
pci/0000:01:00.0/0: type notset flavour cpu port 0 splittable false
pci/0000:01:00.0/53: type eth netdev enp1s0nl8p1 flavour physical lc 8 port 1 splittable true lanes 4
pci/0000:01:00.0/54: type eth netdev enp1s0nl8p2 flavour physical lc 8 port 2 splittable true lanes 4
pci/0000:01:00.0/55: type eth netdev enp1s0nl8p3 flavour physical lc 8 port 3 splittable true lanes 4
pci/0000:01:00.0/56: type eth netdev enp1s0nl8p4 flavour physical lc 8 port 4 splittable true lanes 4
pci/0000:01:00.0/57: type eth netdev enp1s0nl8p5 flavour physical lc 8 port 5 splittable true lanes 4
pci/0000:01:00.0/58: type eth netdev enp1s0nl8p6 flavour physical lc 8 port 6 splittable true lanes 4
pci/0000:01:00.0/59: type eth netdev enp1s0nl8p7 flavour physical lc 8 port 7 splittable true lanes 4
pci/0000:01:00.0/60: type eth netdev enp1s0nl8p8 flavour physical lc 8 port 8 splittable true lanes 4
pci/0000:01:00.0/61: type eth netdev enp1s0nl8p9 flavour physical lc 8 port 9 splittable true lanes 4
pci/0000:01:00.0/62: type eth netdev enp1s0nl8p10 flavour physical lc 8 port 10 splittable true lanes 4
pci/0000:01:00.0/63: type eth netdev enp1s0nl8p11 flavour physical lc 8 port 11 splittable true lanes 4
pci/0000:01:00.0/64: type eth netdev enp1s0nl8p12 flavour physical lc 8 port 12 splittable true lanes 4
pci/0000:01:00.0/125: type eth netdev enp1s0nl8p13 flavour physical lc 8 port 13 splittable true lanes 4
pci/0000:01:00.0/126: type eth netdev enp1s0nl8p14 flavour physical lc 8 port 14 splittable true lanes 4
pci/0000:01:00.0/127: type eth netdev enp1s0nl8p15 flavour physical lc 8 port 15 splittable true lanes 4
pci/0000:01:00.0/128: type eth netdev enp1s0nl8p16 flavour physical lc 8 port 16 splittable true lanes 4

$ devlink lc set pci/0000:01:00.0 lc 8 notype
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the devlink API so the driver is going to be able to create and
destroy linecard instances. There can be multiple line cards per devlink
device. Expose this new type of object over devlink netlink API to the
userspace, with notifications.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kernel test robot reported:

smatch warnings:
net/ipv4/tcp_input.c:5966 tcp_rcv_established() warn: unsigned 'reason' is never less than zero.

I actually had one packetdrill failing because of this bug,
and was about to send the fix :)

v2: Andreas Schwab also pointed out that @reason needs to be negated
    before we reach tcp_drop_reason()

Fixes: 4b506af9 ("tcp: add two drop reasons for tcp_ack()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
tcp: drop reason additions

Currently, TCP is either missing drop reasons,
or pretending that some useful packets are dropped.

This patch series makes "perf record -a -e skb:kfree_skb"
much more usable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

packets in OFO queue might be redundant, and dropped.

tcp_drop() is no longer needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Re-use existing reasons.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) A valid RST packet should be consumed, to not confuse drop monitor.

2) Same remark for packet validating cross syn setup,
   even if we might ignore part of it.

3) When third packet of 3WHS is delayed, do not pretend
   the SYNACK was dropped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add one reason for packets dropped from OFO queue because
of memory pressure.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add TCP_TOO_OLD_ACK and TCP_ACK_UNSENT_DATA drop
reasons so that tcp_rcv_established() can report
them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add basic support for drop reasons in tcp_rcv_state_process()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_rcv_state_process() incorrectly drops packets
instead of consuming it, making drop monitor very noisy,
if not unusable.

Calling tcp_time_wait() or tcp_done() is part
of standard behavior, packets triggering these actions
were not dropped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Creates four new drop reasons for the following cases:

1) packet being rejected by RFC 7323 PAWS check
2) packet being rejected by SEQUENCE check
3) Invalid RST packet
4) Invalid SYN packet
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Small cleanup in tcp_validate_incoming(), no need for rst_seq_match
setting and testing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Whenever tcp_validate_incoming() handles a valid RST packet,
we should not pretend the packet was dropped.

Create a special section at the end of tcp_validate_incoming()
to handle this case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ansuel Smith says:

====================
net: Reduce qca8k_priv space usage

These 6 patch is a first attempt at reducting qca8k_priv space.
The code changed a lot during times and we have many old logic
that can be replaced with new implementation

The first patch drop the tracking of MTU. We mimic what was done
for mtk and we change MTU only when CPU port is changed.

The second patch finally drop a piece of story of this driver.
The ar8xxx_port_status struct was used by the first implementation
of this driver to put all sort of status data for the port...
With the evolution of DSA all that stuff got dropped till only
the enabled state was the only part of the that struct.
Since it's overkill to keep an array of int, we convert the variable
to a simple u8 where we store the status of each port. This is needed
to don't reanable ports on system resume.

The third patch is a preparation for patch 4. As Vladimir explained
in another patch, we waste a tons of space by keeping a duplicate of
the switch dsa ops in qca8k_priv. The only reason for this is to
dynamically set the correct mdiobus configuration (a legacy dsa one,
or a custom dedicated one)
To solve this problem, we just drop the phy_read/phy_write and we
declare a custom mdiobus in any case.
This way we can use a static dsa switch ops struct and we can drop it
from qca8k_priv

Patch 4 drop the duplicated dsa_switch_ops.

Patch 5 is a fixup for mdio read error.

Patch 6 is an effort to standardize how bus name are done.

This series is just a start of more cleanup.

The idea is to move this driver to the qca dir and split common code
from specific code. Also the mgmt eth code still requires some love
and can totally be optimized by recycling the same skb over time.

Also while working on the MTU it was notice some problem with
the stmmac driver and with the reloading phase that cause all
sort of problems with qca8k.

I'm sending this here just to try to keep small series instead of
proposing monster series hard to review.

v2:
- Rework MTU patch
v3:
- Drop unrealated changes from patch 3
- Add fixup patch for mdio read
- Unify bus name for legacy and OF mdio bus
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for multiple switch with OF mdio bus declaration.
Unify the bus id naming and use the same logic for both legacy and OF
mdio bus.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Restore original way to handle mdio read error by returning 0xffff.
This was wrongly changed when the internal_mdio_read was introduced,
now that both legacy and internal use the same function, make sure that
they behave the same way.

Fixes: ce062a0a ("net: dsa: qca8k: fix kernel panic with legacy mdio mapping")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that dsa_switch_ops is not switch specific anymore, we can drop it
from qca8k_priv and use the static ops directly for the dsa_switch
pointer.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In an attempt to reduce qca8k_priv space, rework and simplify mdiobus
logic.
We now declare a mdiobus instead of relying on DSA phy_read/write even
if a mdio node is not present. This is all to make the qca8k ops static
and not switch specific. With a legacy implementation where port doesn't
have a phy map declared in the dts with a mdio node, we declare a
'qca8k-legacy' mdiobus. The conversion logic is used as legacy read and
write ops are used instead of the internal one.
Also drop the legacy_phy_port_mapping as we now declare mdiobus with ops
that already address the workaround.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Port_sts is a thing of the past for this driver. It was something
present on the initial implementation of this driver and parts of the
original struct were dropped over time. Using an array of int to store if
a port is enabled or not to handle PM operation seems overkill. Switch
and use a simple u8 to store the port status where each bit correspond
to a port. (bit is set port is enabled, bit is not set, port is disabled)
Also add some comments to better describe why we need to track port
status.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DSA set the CPU port based on the largest MTU of all the slave ports.
Based on this we can drop the MTU array from qca8k_priv and set the
port_change_mtu logic on DSA changing MTU of the CPU port as the switch
have a global MTU settingfor each port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new neighbour cache entry in STALE state for routers on receiving
an unsolicited (gratuitous) neighbour advertisement with
target link-layer-address option specified.
This is similar to the arp_accept configuration for IPv4.
A new sysctl endpoint is created to turn on this behaviour:
/proc/sys/net/ipv6/conf/interface/accept_unsolicited_na.
Signed-off-by: Arun Ajith S <aajith@arista.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

idev can be NULL, as the surrounding code suggests.

Fixes: 4daf841a ("net: ipv6: add skb drop reasons to ip6_rcv_core()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Menglong Dong <imagedong@tencent.com>
Cc: Jiang Biao <benbjiang@tencent.com>
Cc: Hao Peng <flyingpeng@tencent.com>
Link: https://lore.kernel.org/r/20220413205653.1178458-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

For some unknown reason qdisc_reset() is using
a convoluted way of freeing two lists of skbs.

Use __skb_queue_purge() instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20220414011004.2378350-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In review comment [1] was pointed that new code is not supposed
to set driver version and should rely on kernel version instead.

As an outcome of that comment all the dance around setting such
driver version to FW should be removed too, because in upstream
kernel whole driver will have same version so read/write from/to
FW will give same result.

[1] https://lore.kernel.org/all/YladGTmon1x3dfxI@unreal

Fixes: 862cd659 ("octeon_ep: Add driver framework and device initialization")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/5d76f3116ee795071ec044eabb815d6c2bdc7dbd.1649922731.git.leonro@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Sukadev Bhattiprolu says:

====================
ibmvnic: Use a set of LTBs per pool

ibmvnic uses a single large long term buffer (LTB) per rx or tx
pool (queue). This has two limitations.

First, if we need to free/allocate an LTB (eg during a reset), under
low memory conditions, the allocation can fail.

Second, the kernel limits the size of single LTB (DMA buffer) to 16MB
(based on MAX_ORDER). With jumbo frames (mtu = 9000) we can only have
about 1763 buffers per LTB (16MB / 9588 bytes per frame) even though
the max supported buffers is 4096. (The 9588 instead of 9088 comes from
IBMVNIC_BUFFER_HLEN.)

To overcome these limitations, allow creating a set of LTBs per queue.
====================

Link: https://lore.kernel.org/r/20220413171026.1264294-1-drt@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Allow multiple LTBs in the txpool's ltb_set. i.e rather than using
a single large LTB, use several smaller LTBs.

The first n-1 LTBs will all be of the same size. The size of the last
LTB in the set depends on the number of buffers and buffer (mtu) size.
This strategy hopefully allows more reuse of the initial LTBs and also
reduces the chances of an allocation failure (of the large LTB) when
system is low in memory.
Suggested-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>