* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  sky2: version 1.18
  sky2: receive FIFO checking
  sky2: fe+ chip support
  sky2: reorganize chip revision features
  sky2: ethtool speed report bug
  sky2: fix VLAN receive processing (resend)
  phy: export phy_mii_ioctl
  myri10ge: Add support for PCI device id 9

Update version number
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

A driver writer from another operating system hinted that
the versions of Yukon 2 chip with rambuffer (EC and XL) have
a hardware bug that if the FIFO ever gets completely full it
will hang. Sounds like a classic ring full vs ring empty wrap around
bug.

As a workaround, use the existing watchdog timer to check for
ring full lockup.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add support for newest Marvell chips.
The Yukon FE plus chip is found in some not yet released laptops.
Tested on hardware evaluation boards.

This version of the patch is for 2.6.23. It supersedes
the two previous patches that are sitting in netdev-2.6 (upstream branch).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch should cause no functional changes in driver behaviour.
There are (too) many revisions of the Yukon 2 chip now. Instead of
adding more conditionals based on chip revision; rerganize into a
set of feature flags so adding new versions is less problematic.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

On 100mbit versions, the driver always reports gigabit speed
available. The correct modes are already computed, then overwritten.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The length check for truncated frames was not correctly handling
the case where VLAN acceleration had already read the tag.
Also, the Yukon EX has some features that use high bit of status
as security tag.
Signed-off-by: Pierre-Yves Ritschard <pyr@spootnik.org>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Initialization of ohci1394 was broken according to one reporter if the
driver was statically linked, i.e. not built as loadable module.  Dmesg:

  PCI: Device 0000:02:07.0 not available because of resource collisions
  ohci1394: Failed to enable OHCI hardware.

This was reported for a Toshiba Satellite 5100-503.  The cause is commit
8df4083c in Linux 2.6.19-rc1 which only
served purposes of early remote debugging via FireWire.  This
functionality is better provided by the currently out-of-tree driver
ohci1394_earlyinit.  Reversal of the commit was OK'd by Andi Kleen.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Emil Medve points out that this documentation file uses CRLF line
endings, which means that if you use

	[core]
		autocrlf=input

(which makes sense if you ever develop under Windows, for example, or if
you use other broken tools) in your git config, git will always complain
about the file being dirty.

This removes the bogus DOS line endings, and removes whitespace at the
end of line.

Cc: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There's an obvious typo in arch/i386/boot/header.S (in your
linux-2.6-x86setup.git) that I noticed by just studying the code.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

wakeup.S looks at the video mode number from the setup header and
looks to see if it is a VESA mode.  Unfortunately, the decoding is
done incorrectly and it will attempt to frob the VESA BIOS for any
mode number 0x0200 or larger.  Correct this, and remove a bunch of #if
0'd code.

Massive thanks to Jeff Chua for reporting the bug, and suffering
though a large number of experiments in order to track this problem
down.

Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Canonicalize the video mode number as presented to the kernel.  The
video mode number may be user-entered (e.g. ASK_VGA), an alias
(e.g. NORMAL_VGA), or a size specification, and that confuses the
suspend wakeup code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Export phy_mii_ioctl, so network drivers can use it when built
as modules too.
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: fix invalid sched_class use
  sched: add /proc/sys/kernel/sched_compat_yield

Given an illegal selinux option it was possible for match_token to work in
random memory at the end of the match_table_t array.

Note that privilege is required to perform a context mount, so this issue is
effectively limited to root only.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>

When using rt_mutex, a NULL pointer dereference is occurred at
enqueue_task_rt. Here is a scenario;
1) there are two threads, the thread A is fair_sched_class and
   thread B is rt_sched_class.
2) Thread A is boosted up to rt_sched_class, because the thread A
   has a rt_mutex lock and the thread B is waiting the lock.
3) At this time, when thread A create a new thread C, the thread
   C has a rt_sched_class.
4) When doing wake_up_new_task() for the thread C, the priority
   of the thread C is out of the RT priority range, because the
   normal priority of thread A is not the RT priority. It makes
   data corruption by overflowing the rt_prio_array.
The new thread C should be fair_sched_class.

The new thread should be valid scheduler class before queuing.
This patch fixes to set the suitable scheduler class.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>

add /proc/sys/kernel/sched_compat_yield to make sys_sched_yield()
more agressive, by moving the yielding task to the last position
in the rbtree.

with sched_compat_yield=0:

   PID USER      PR  NI  VIRT  RES  SHR S %CPU %MEM    TIME+  COMMAND
  2539 mingo     20   0  1576  252  204 R   50  0.0   0:02.03 loop_yield
  2541 mingo     20   0  1576  244  196 R   50  0.0   0:02.05 loop

with sched_compat_yield=1:

   PID USER      PR  NI  VIRT  RES  SHR S %CPU %MEM    TIME+  COMMAND
  2584 mingo     20   0  1576  248  196 R   99  0.0   0:52.45 loop
  2582 mingo     20   0  1576  256  204 R    0  0.0   0:00.00 loop_yield
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>

Add support for new Myri-10G boards with PCI device id 9.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] cpu-bugs64.c: GCC 3.3 constraint workaround
  [MIPS] DEC: Initialise ioasic_ssr_lock

* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (6173a): Documentation: Remove reference to dead "cpia_pp=" boot-time option
  Revert "V4L/DVB (6173a): Documentation: Remove reference to dead "cpia_pp=" boot-time option"

* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
  [XFS] Avoid replaying inode buffer initialisation log items if on-disk version is newer.
  [XFS] Ensure file size updates have been completed before writing inode to disk.
  [XFS] On-demand reaping of the MRU cache

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SUNSAB]: Fix several bugs.

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: remove unused variables from drivers/ide/ppc/pmac.c
  ide: ST320413A has the same problem as ST340823A

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Fix timekeeping on PowerPC 601
  [POWERPC] Don't expose clock vDSO functions when CPU has no timebase
  [POWERPC] spusched: Fix null pointer dereference in find_victim

Randy Dunlap noticed an interesting "crashme" behaviour on his dual
Prescott Xeon setup, where he gets page faults with the error code
having a zero "user" bit, but the register state points back to user
mode.

This may be a CPU microcode buglet triggered by some strange instruction
pattern that crashme generates, and loading a microcode update seems to
possibly have fixed it.

Regardless, we really should trust the register state more than the
error code, since it's really the register state that determines whether
we can actually send a signal, or whether we're in kernel mode and need
to oops/kill the process in the case of a page fault.

Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add a workaround to address warnings generated on the "n" constraint by
GCC 3.3 and below.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Fix the definition of the ioasic_ssr_lock spinlock to include a proper 
initialisation.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Nested class devices used to have 'device' symlink point to a real
(physical) device instead of a parent class device.  When converting
subsystems to struct device we need to keep doing what class devices did if
CONFIG_SYSFS_DEPRECATED is Y, otherwise parts of udev break.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Greg KH <greg@kroah.com>
Tested-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixes a crash caused by an interrupt coming in when an IRQ stack
is being torn down.  When this happens, handle_signal will loop, setting up
the IRQ stack again because the tearing down had finished, and handling
whatever signals had come in.

However, to_irq_stack returns a mask of pending signals to be handled, plus
bit zero is set if the IRQ stack was already active, and thus shouldn't be
torn down.  This causes a problem because when handle_signal goes around
the loop, sig will be zero, and to_irq_stack will duly set bit zero in the
returned mask, faking handle_signal into believing that it shouldn't tear
down the IRQ stack and return thread_info pointers back to their original
values.

This will eventually cause a crash, as the IRQ stack thread_info will
continue pointing to the original task_struct and an interrupt will look
into it after it has been freed.

The fix is to stop passing a signal number into to_irq_stack.  Rather, the
pending signals mask is initialized beforehand with the bit for sig already
set.  References to sig in to_irq_stack can be replaced with references to
the mask.

[akpm@linux-foundation.org: use UL]
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch proposes fixes to the reference counting of memory policy in the
page allocation paths and in show_numa_map().  Extracted from my "Memory
Policy Cleanups and Enhancements" series as stand-alone.

Shared policy lookup [shmem] has always added a reference to the policy,
but this was never unrefed after page allocation or after formatting the
numa map data.

Default system policy should not require additional ref counting, nor
should the current task's task policy.  However, show_numa_map() calls
get_vma_policy() to examine what may be [likely is] another task's policy.
The latter case needs protection against freeing of the policy.

This patch adds a reference count to a mempolicy returned by
get_vma_policy() when the policy is a vma policy or another task's
mempolicy.  Again, shared policy is already reference counted on lookup.  A
matching "unref" [__mpol_free()] is performed in alloc_page_vma() for
shared and vma policies, and in show_numa_map() for shared and another
task's mempolicy.  We can call __mpol_free() directly, saving an admittedly
inexpensive inline NULL test, because we know we have a non-NULL policy.

Handling policy ref counts for hugepages is a bit trickier.
huge_zonelist() returns a zone list that might come from a shared or vma
'BIND policy.  In this case, we should hold the reference until after the
huge page allocation in dequeue_hugepage().  The patch modifies
huge_zonelist() to return a pointer to the mempolicy if it needs to be
unref'd after allocation.

Kernel Build [16cpu, 32GB, ia64] - average of 10 runs:

		w/o patch	w/ refcount patch
	    Avg	  Std Devn	   Avg	  Std Devn
Real:	 100.59	    0.38	 100.63	    0.43
User:	1209.60	    0.37	1209.91	    0.31
System:   81.52	    0.42	  81.64	    0.34
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It turned out, that the user namespace is released during the do_exit() in
exit_task_namespaces(), but the struct user_struct is released only during the
put_task_struct(), i.e.  MUCH later.

On debug kernels with poisoned slabs this will cause the oops in
uid_hash_remove() because the head of the chain, which resides inside the
struct user_namespace, will be already freed and poisoned.

Since the uid hash itself is required only when someone can search it, i.e.
when the namespace is alive, we can safely unhash all the user_struct-s from
it during the namespace exiting.  The subsequent free_uid() will complete the
user_struct destruction.

For example simple program

   #include <sched.h>

   char stack[2 * 1024 * 1024];

   int f(void *foo)
   {
   	return 0;
   }

   int main(void)
   {
   	clone(f, stack + 1 * 1024 * 1024, 0x10000000, 0);
   	return 0;
   }

run on kernel with CONFIG_USER_NS turned on will oops the
kernel immediately.

This was spotted during OpenVZ kernel testing.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Acked-by: "Serge E. Hallyn" <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Surprisingly, but (spotted by Alexey Dobriyan) the uid hash still uses
list_heads, thus occupying twice as much place as it could.  Convert it to
hlist_heads.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/user.c: Convert list_for_each to list_for_each_entry in
uid_hash_find()
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The do_split() function for htree dir blocks is intended to split a leaf
block to make room for a new entry.  It sorts the entries in the original
block by hash value, then moves the last half of the entries to the new
block - without accounting for how much space this actually moves.  (IOW,
it moves half of the entry *count* not half of the entry *space*).  If by
chance we have both large & small entries, and we move only the smallest
entries, and we have a large new entry to insert, we may not have created
enough space for it.

The patch below stores each record size when calculating the dx_map, and
then walks the hash-sorted dx_map, calculating how many entries must be
moved to more evenly split the existing entries between the old block and
the new block, guaranteeing enough space for the new entry.

The dx_map "offs" member is reduced to u16 so that the overall map size
does not change - it is temporarily stored at the end of the new block, and
if it grows too large it may be overwritten.  By making offs and size both
u16, we won't grow the map size.

Also add a few comments to the functions involved.

This fixes the testcase reported by hooanon05@yahoo.co.jp on the
linux-ext4 list, "ext3 dir_index causes an error"

Thanks to Andreas Dilger for discussing the problem & solution with me.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Tested-by: Junjiro Okajima <hooanon05@yahoo.co.jp>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: <linux-ext4@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There is still some confusion and disagreement over what this interface should
actually do.  So it is best that we disable it in 2.6.23 until we get that
fully sorted out.

(sys_timerfd() was present in 2.6.22 but it was apparently broken, so here we
assume that nobody is using it yet).

Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Davide Libenzi <davidel@xmailserver.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

NFS unregisters sysctls only if V4 support is compiled in.  However, sysctl
table is not V4 specific, so unregister it always.

Steps to reproduce:

	[build nfs.ko with CONFIG_NFS_V4=n]
	modrobe nfs
	rmmod nfs
	ls /proc/sys

Unable to handle kernel paging request at ffffffff880661c0 RIP:
 [<ffffffff802af8e3>] proc_sys_readdir+0xd3/0x350
PGD 203067 PUD 207063 PMD 7e216067 PTE 0
Oops: 0000 [1] SMP
CPU 1
Modules linked in: lockd nfs_acl sunrpc
Pid: 3335, comm: ls Not tainted 2.6.23-rc3-bloat #2
RIP: 0010:[<ffffffff802af8e3>]  [<ffffffff802af8e3>] proc_sys_readdir+0xd3/0x350
RSP: 0018:ffff81007fd93e78  EFLAGS: 00010286
RAX: ffffffff880661c0 RBX: ffffffff80466370 RCX: ffffffff880661c0
RDX: 00000000000014c0 RSI: ffff81007f3ad020 RDI: ffff81007efd8b40
RBP: 0000000000000018 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: ffffffff802a8570 R12: ffffffff880661c0
R13: ffff81007e219640 R14: ffff81007efd8b40 R15: ffff81007ded7280
FS:  00002ba25ef03060(0000) GS:ffff81007ff81258(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffffffff880661c0 CR3: 000000007dfaf000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process ls (pid: 3335, threadinfo ffff81007fd92000, task ffff81007d8a0000)
Stack:  ffff81007f3ad150 ffffffff80283f30 ffff81007fd93f48 ffff81007efd8b40
 ffff81007ee00440 0000000422222222 0000000200035593 ffffffff88037e9a
 2222222222222222 ffffffff80466500 ffff81007e416400 ffff81007e219640
Call Trace:
 [<ffffffff80283f30>] filldir+0x0/0xf0
 [<ffffffff80283f30>] filldir+0x0/0xf0
 [<ffffffff802840c7>] vfs_readdir+0xa7/0xc0
 [<ffffffff80284376>] sys_getdents+0x96/0xe0
 [<ffffffff8020bb3e>] system_call+0x7e/0x83

Code: 41 8b 14 24 85 d2 74 dc 49 8b 44 24 08 48 85 c0 74 e7 49 3b
RIP  [<ffffffff802af8e3>] proc_sys_readdir+0xd3/0x350
 RSP <ffff81007fd93e78>
CR2: ffffffff880661c0
Kernel panic - not syncing: Fatal exception
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Convert asserts (BUGs) in dx_probe from bad on-disk data to recoverable
errors with helpful warnings.  With help catching other asserts from Duane
Griffin <duaneg@dghda.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Duane Griffin <duaneg@dghda.com>
Acked-by: Theodore Ts'o <tytso@mit.edu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The mask on i830 should be 0x70 always, later chips 0xF0 should be okay.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Acked-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Cc: Michael Haas <laga@laga.ath.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Reported in Kernel Bugzilla 9006

Fix an obvious bug in DPLL disable.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>