Skip to content

L
linux
Switch branch/tag
  1. 28 Nov, 2010 6 commits
  3. 25 Nov, 2010 1 commit
  5. 24 Nov, 2010 7 commits
  7. 23 Nov, 2010 1 commit
  9. 22 Nov, 2010 8 commits
    • Christian Lamparter's avatar
      carl9170: fix virtual interface setup crash · b397492a
      Christian Lamparter authored 
      This patch fixes a faulty bound check which caused a
crash when too many virtual interface were brought up.

BUG: unable to handle kernel NULL pointer dereference at 00000004
IP: [<f8125f67>] carl9170_op_add_interface+0x1d7/0x2c0 [carl9170]
*pde = 00000000
Oops: 0002 [#1] PREEMPT
Modules linked in: carl9170 [...]
Pid: 4720, comm: wpa_supplicant Not tainted 2.6.37-rc2-wl+
EIP: 0060:[<f8125f67>] EFLAGS: 00210206 CPU: 0
EIP is at carl9170_op_add_interface+0x1d7/0x2c0 [carl9170]
EAX: 00000000 ...
Process wpa_supplicant
Stack:
 f4f88f34 fffffff4 ..
Call Trace:
 [<f8f4e666>] ? ieee80211_do_open+0x406/0x5c0 [mac80211]
 [...]
Code: <89> 42 04 ...
EIP: [<f8125f67>] carl9170_op_add_interface+0x1d7/0x2c0 [carl9170]
CR2: 0000000000000004
Signed-off-by: default avatarChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      b397492a
    • Daniel Klaffenbach's avatar
      ssb: b43-pci-bridge: Add new vendor for BCM4318 · 1d8638d4
      Daniel Klaffenbach authored 
      Add new vendor for Broadcom 4318.
Signed-off-by: default avatarDaniel Klaffenbach <danielklaffenbach@gmail.com>
Signed-off-by: default avatarLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      1d8638d4
    • Felix Fietkau's avatar
      ath9k: fix timeout on stopping rx dma · d47844a0
      Felix Fietkau authored 
      It seems that using ath9k_hw_stoppcurecv to stop rx dma is not enough.
When it's time to stop DMA, the PCU is still busy, so the rx enable
bit never clears.
Using ath9k_hw_abortpcurecv helps with getting rx stopped much faster,
with this change, I cannot reproduce the rx stop related WARN_ON anymore.
Signed-off-by: default avatarFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      d47844a0
    • David Daney's avatar
      of/phylib: Use device tree properties to initialize Marvell PHYs. · cf41a51d
      David Daney authored 
      Some aspects of PHY initialization are board dependent, things like
indicator LED connections and some clocking modes cannot be determined
by probing.  The dev_flags element of struct phy_device can be used to
control these things if an appropriate value can be passed from the
Ethernet driver.  We run into problems however if the PHY connections
are specified by the device tree.  There is no way for the Ethernet
driver to know what flags it should pass.

If we are using the device tree, the struct phy_device will be
populated with the device tree node corresponding to the PHY, and we
can extract extra configuration information from there.

The next question is what should the format of that information be?
It is highly device specific, and the device tree representation
should not be tied to any arbitrary kernel defined constants.  A
straight forward representation is just to specify the exact bits that
should be set using the "marvell,reg-init" property:

      phy5: ethernet-phy@5 {
        reg = <5>;
        compatible = "marvell,88e1149r";
        marvell,reg-init =
                /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */
                <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */
                /* mix %:0, led[0123]:drive low off hiZ */
                <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */
                /* default blink periods. */
                <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */
                /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */
                <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */
      };

      phy6: ethernet-phy@6 {
        reg = <6>;
        compatible = "marvell,88e1118";
        marvell,reg-init =
                /* Fix rx and tx clock transition timing */
                <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
                /* Adjust LED drive. */
                <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
                /* irq, blink-activity, blink-link */
                <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
      };

The Marvell PHYs have a page select register at register 22 (0x16), we
can specify any register by its page and register number.  These are
the first and second word.  The third word contains a mask to be ANDed
with the existing register value, and the fourth word is ORed with the
result to yield the new register value.  The new marvell_of_reg_init
function leaves the page select register unchanged, so a call to it
can be dropped into the .config_init functions without unduly
affecting the state of the PHY.

If CONFIG_OF_MDIO is not set, there is no of_node, or no
"marvell,reg-init" property, the PHY initialization is unchanged.
Signed-off-by: default avatarDavid Daney <ddaney@caviumnetworks.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: default avatarGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      cf41a51d
    • David Daney's avatar
      phylib: Add support for Marvell 88E1149R devices. · 90600732
      David Daney authored 
      The 88E1149R is 10/100/1000 quad-gigabit Ethernet PHY.  The
.config_aneg function can be shared with 88E1118, but it needs its own
.config_init.
Signed-off-by: default avatarDavid Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      90600732
    • David Daney's avatar
      phylib: Use common page register definition for Marvell PHYs. · 27d916d6
      David Daney authored 
      The definition of the Marvell PHY page register is not specific to
88E1121, so rename the macro to MII_MARVELL_PHY_PAGE, and use it
throughout.
Suggested-by: default avatarCyril Chemparathy <cyril@ti.com>
Signed-off-by: default avatarDavid Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      27d916d6
    • Sonny Rao's avatar
      qlge: Fix incorrect usage of module parameters and netdev msg level · 84cf7029
      Sonny Rao authored 
      Driver appears to be mistaking the permission field with default value
in the case of debug and qlge_irq_type.

Driver is also passing debug as a bitmask into netif_msg_init()
which wants a number of bits.  Ron Mercer suggests we should
change this to pass in -1 so the defaults get used instead,
which makes the default much less verbose.
Signed-off-by: default avatarMilton Miller <miltonm@bga.com>
Signed-off-by: default avatarSonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      84cf7029
    • John Fastabend's avatar
      ipv6: fix missing in6_ifa_put in addrconf · 88b2a9a3
      John Fastabend authored 
      Fix ref count bug introduced by

commit 2de79570
Author: Lorenzo Colitti <lorenzo@google.com>
Date:   Wed Oct 27 18:16:49 2010 +0000

ipv6: addrconf: don't remove address state on ifdown if the address
is being kept

Fix logic so that addrconf_ifdown() decrements the inet6_ifaddr
refcnt correctly with in6_ifa_put().
Reported-by: default avatarStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: default avatarJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: default avatarEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      88b2a9a3
  11. 21 Nov, 2010 5 commits
  13. 19 Nov, 2010 2 commits
  15. 18 Nov, 2010 10 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7