callid_sock array is referenced via rcu_dereference and
sparse rcu checks complains about address space mismatch.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit cda5f98e.

As per Vlad's request.
Signed-off-by: David S. Miller <davem@davemloft.net>

With the restructuring of the lksctp.org site, we only allow bug
reports through the SCTP mailing list linux-sctp@vger.kernel.org,
not via SF, as SF is only used for web hosting and nothing more.
While at it, also remove the obvious statement that bugs will be
fixed and incooperated into the kernel.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Get rid of the last module parameter for SCTP and make this
configurable via sysctl for SCTP like all the rest of SCTP's
configuration knobs.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds the new procfs knobs:

    /proc/sys/net/ipv4/conf/*/igmpv2_unsolicited_report_interval
    /proc/sys/net/ipv4/conf/*/igmpv3_unsolicited_report_interval

Which will allow userspace configuration of the IGMP unsolicited report
interval (see below) in milliseconds.  The defaults are 10000ms for IGMPv2
and 1000ms for IGMPv3 in accordance with RFC2236 and RFC3376.

Background:

If an IGMP join packet is lost you will not receive data sent to the
multicast group so if no data arrives from that multicast group in a
period of time after the IGMP join a second IGMP join will be sent.  The
delay between joins is the "IGMP Unsolicited Report Interval".

Prior to this patch this value was hard coded in the kernel to 10s for
IGMPv2 and 1s for IGMPv3.  10s is unsuitable for some use-cases, such as
IPTV as it can cause channel change to be slow in the presence of packet
loss.

This patch allows the value to be overridden from userspace for both
IGMPv2 and IGMPv3 such that it can be tuned accoding to the network.

Tested with Wireshark and a simple program to join a (non-existent)
multicast group.  The distribution of timings for the second join differ
based upon setting the procfs knobs.

igmpvX_unsolicited_report_interval is intended to follow the pattern
established by force_igmp_version, and while a procfs entry has been added
a corresponding sysctl knob has not as it is my understanding that sysctl
is deprecated[1].

[1]: http://lwn.net/Articles/247243/Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The procfs knob /proc/sys/net/ipv4/conf/*/force_igmp_version allows the
IGMP protocol version to use to be explicitly set.  As a side effect this
caused the routing cache to be flushed as it was declared as a
DEVINET_SYSCTL_FLUSHING_ENTRY.  Flushing is unnecessary and this patch
makes it so flushing does not occur.

Requested by Hannes Frederic Sowa as he was reviewing other patches
adding procfs entries.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If an IGMP join packet is lost you will not receive data sent to the
multicast group so if no data arrives from that multicast group in a
period of time after the IGMP join a second IGMP join will be sent.  The
delay between joins is the "IGMP Unsolicited Report Interval".

Previously this value was hard coded to be chosen randomly between 0-10s.
This can be too long for some use-cases, such as IPTV as it can cause
channel change to be slow in the presence of packet loss.

The value 10s has come from IGMPv2 RFC2236, which was reduced to 1s in
IGMPv3 RFC3376.  This patch makes the kernel use the 1s value from the
later RFC if we are operating in IGMPv3 mode.  IGMPv2 behaviour is
unaffected.

Tested with Wireshark and a simple program to join a (non-existent)
multicast group.  The distribution of timings for the second join differ
based upon setting /proc/sys/net/ipv4/conf/eth0/force_igmp_version.
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of bond_add_vlan() failure currently we'll have the vlan's
refcnt bumped up in all slaves, but it will never go down because it
failed to get added to the bond, so properly unwind the added vlan if
bond_add_vlan fails.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now we have vlan_vids_add/del_by_dev() which serve the same purpose as
bond's bond_add/del_vlans_on_slave() with the good side effect of
reverting the changes if one of the additions fails.
There's only 1 change in the behaviour of enslave: if adding of the
vlans to the slave fails, we'll fail the enslaving because otherwise we
might delete some vlan that wasn't added by the bonding.
The only way this may happen is with ENOMEM currently, so we're in trouble
anyway.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With GRO/LRO processing, there is a problem because Ip[6]InReceives SNMP
counters do not count the number of frames, but number of aggregated
segments.

Its probably too late to change this now.

This patch adds four new counters, tracking number of frames, regardless
of LRO/GRO, and on a per ECN status basis, for IPv4 and IPv6.

Ip[6]NoECTPkts : Number of packets received with NOECT
Ip[6]ECT1Pkts  : Number of packets received with ECT(1)
Ip[6]ECT0Pkts  : Number of packets received with ECT(0)
Ip[6]CEPkts    : Number of packets received with Congestion Experienced

lph37:~# nstat | egrep "Pkts|InReceive"
IpInReceives                    1634137            0.0
Ip6InReceives                   3714107            0.0
Ip6InNoECTPkts                  19205              0.0
Ip6InECT0Pkts                   52651828           0.0
IpExtInNoECTPkts                33630              0.0
IpExtInECT0Pkts                 15581379           0.0
IpExtInCEPkts                   6                  0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commits:

0f75b09c
cbd89acb
c483e026

Amongst other things, it's modifies the SKB header
to pull the ethernet headers off via eth_type_trans()
on the output path which is bogus.

It's causing serious regressions for people.
Signed-off-by: David S. Miller <davem@davemloft.net>

Added missing __iomem annotation in order to fix the following
sparse warnings:

drivers/net/phy/mdio-mux-mmioreg.c:51:27: warning: incorrect type in initializer (different address spaces)
drivers/net/phy/mdio-mux-mmioreg.c:51:27:    expected void *p
drivers/net/phy/mdio-mux-mmioreg.c:51:27:    got void [noderef] <asn:2>*
drivers/net/phy/mdio-mux-mmioreg.c:57:21: warning: incorrect type in argument 1 (different address spaces)
drivers/net/phy/mdio-mux-mmioreg.c:57:21:    expected void const volatile [noderef] <asn:2>*addr
drivers/net/phy/mdio-mux-mmioreg.c:57:21:    got void *p
drivers/net/phy/mdio-mux-mmioreg.c:60:25: warning: incorrect type in argument 2 (different address spaces)
drivers/net/phy/mdio-mux-mmioreg.c:60:25:    expected void volatile [noderef] <asn:2>*addr
drivers/net/phy/mdio-mux-mmioreg.c:60:25:    got void *p
drivers/net/phy/mdio-mux-mmioreg.c:64:25: warning: incorrect type in argument 1 (different address spaces)
drivers/net/phy/mdio-mux-mmioreg.c:64:25:    expected void volatile [noderef] <asn:2>*addr
drivers/net/phy/mdio-mux-mmioreg.c:64:25:    got void *p
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ksz8873mll_read_status() is used only in this file.
Fix the following sparse warning:

drivers/net/phy/micrel.c:147:5: warning: symbol 'ksz8873mll_read_status' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use skb_copy_datagram_from_iovec() to avoid code duplication and make it easy to
be read. Also we can do the skipping inside the zero-copy loop.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To reduce the duplicated codes.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To let it be reused and reduce code duplication. Also document this function.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To let it be reused and reduce code duplication.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IP tunnel hash heads can be embedded in the per-net structure
since it is a fixed size. Reduce the size so that the total structure
fits in a page size. The original size was overly large, even NETDEV_HASHBITS
is only 8 bits!

Also, add some white space for readability.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>

and update copyright year.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

WoL and power state changes will now be done in the shutdown handler.
open/close/ethtool will no longer change the power state.  NVRAM
operations can now be permitted whether the device is up or down.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This simplifies the suspend/resume code.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Separate MAC and PHY WoL setup code into a separate function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simple API changes with no functional changes.
Signed-off-by: Michael Chan <mchan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

by closing the device if necessary.  Otherwise, since NAPI state is
already disabled, a subsequent close will hang the system.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Uninitialized value was being returned in the non-failure case.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Log the event type for unknown async events
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The BE2 FW GET_PHY_DETAILS cmd does not return fixed speeds supported.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For SH-R and Lancer-R, use the FW supported values for Max unicast MACs,
Max VLANs and Max multicast MACs.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a chip wide value and the PFs already report it.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new speeds are supported by variants of the Skyhawk-R chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>