into ppc970.osdl.org:/home/torvalds/v2.6/linux

OK, let's make it the same as IPv4.  This is still broken
as the calculation is wrong.  However, to fix it properly
we need to store the MTUs inside the dst's.  I'll get
around to that sooner or later.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Patch from Ben Dooks

S3C2410/S3C2440 new serial driver

this patch includes the following

- clock selection using clock core
- handling for both 2410 and 2440 uarts
- uart suspend/resume support
- Dimitry Andric's fix for un-initialised spinlocks
- Herbert Poetzl's fixes for the following
-> break character recognition
-> Magic-SYSRQ handling
-> Uart software flow control (IrDA console)

Updated to include rmk's comments from Patch #2234/1
and fix a few checks for serial clocks, as well as
merging fixes from rmk that had taken time to go
through the biteepr to release.

Signed-off-by: Ben Dooks
Signed-off-by: Russell King

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Patch from Ben Dooks

Move the configuration for the UART to use for the low-level
messages generated by the uncompressor out of the kernel debug
section, which means the system builds properly without having
kernel debug enabled.

Also remove the use of including <config/xxx.h> headers,
and the default configuration updates

Signed-off-by: Ben Dooks
Signed-off-by: Russell King

Patch from Ben Dooks

Ensure the i2c platform device has the correct name if the
system is an s3c2440.

Signed-off-by: Ben Dooks
Signed-off-by: Russell King

Patch from Ben Dooks

Move the pm code to use the machine's init_machine
code, instead of an late_initcall(). This change is
as-per the documentation, and means we do not need to
check for machine type in the init code.

Thanks to Dimitry Andric for pointing this out

Signed-off-by: Ben Dooks
Signed-off-by: Russell King

Patch from Ben Dooks

Updates for the Simtec BAST (EB2410ITX) default configuration
to fix the following:

- add mtd support for NAND and NOR
- remove PC style parallel port (does not build)
- use S3C2410 core RTC for time
- remove non-bast S3C2410 machines

Signed-off-by: Ben Dooks
Signed-off-by: Russell King

Patch from Ben Dooks

updates to the default configuration to change the
following:

- use S3C2410 internal rtc instead of PC style rtc
- add mtd support for nand
- add mtd support for nor (and bast nor mapping)

Signed-off-by: Ben Dooks
Signed-off-by: Russell King

Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for 5753 chips which is mostly just adding
in the appropriate PCI ids and recognizing that these
chips do not use GPIO2 for Vaux switching.

Also do not set DMA read water mark on PCI Express.
In such configurations these bits are reserved.
Signed-off-by: David S. Miller <davem@davemloft.net>

Just tried the new toy. It works.

into nuts.davemloft.net:/disk1/BK/net-2.6

Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>

into coreworks.de:/home/kaber/src/nf/nf-2.6

into coreworks.de:/home/kaber/src/nf/nf-2.6

into coreworks.de:/home/kaber/src/nf/nf-2.6

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Found running netfilter code under valgrind: we return some
uninitialized stack to userspace (needs root).  Almost certainly
harmless, but this suppressed the valgrind complaint, and
doesn't hurt.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fix to find_appropriate_src left a stupid test, which has no
effect but is incoherent at best.  It covers a corner case: if a
previous connection from this source was mapped onto a different IP
address (because it was explicitly told to), should the next one be
mapped that was as well, if no explicit rule says to remap the src IP?

I think the answer is yes: unless the user explicitly tells us to map
into a particular range, we should follow the Kegel draft.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

into ppc970.osdl.org:/home/torvalds/v2.6/linux

While doing the 2.4 version of the netlink patch, I noticed a bug
in my mc_list code.  First of all it wasn't holding the table lock
when adding nodes to the list.  It also didn't take the node off
the list when multicast is switched off.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure loopback_dev, if up, has the ipv6 bits
for it setup before the addrconf netdev notifier
is registered.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

The patch to change traps and interrupts to the fastcall convention
missed the machine check handlers.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

asked for it.

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Patch from Ben Dooks

Update the s3c2410 machines for the new serial handling,
as well as add the clock sources the bast and vr1000
rely on.

Signed-off-by: Ben Dooks
Signed-off-by: Russell King

Patch from Ben Dooks

Update the arch/arm/mach-s3c2410 core files for the
new serial port bits, and fix the bugs with s3c2440
handling.

Signed-off-by: Ben Dooks
Signed-off-by: Russell King

Patch from Ben Dooks

Clock code now uses the supplied device to check for
the id of the clock, so uart clocks are now simply
"uart" instead of "uart0", "uart1" and "uart2"

Signed-off-by: Ben Dooks
Signed-off-by: Russell King

Move ColdFire 5282 based senTec board startup code to the common
528x directory.
Signed-off-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Include the 527x and 528x family SIM module hardware definitions in the
generic SIM include. All ColdFire specific code just includes the generic
sim include without regard to which actuall ColdFire family member we
are compiling for.
Signed-off-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Add ColdFire 528x specific CPU reset code.
Signed-off-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Kernel startup code specific to the ColdFire 5272 based Feith
SACLES board.
Signed-off-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>