These were accidentally undersized by a factor of 2, which limited
performance.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to support all three modes of macvlan at
runtime, extend the existing netlink protocol
to allow choosing the mode per macvlan slave
interface.

This depends on a matching patch to iproute2
in order to become accessible in user land.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows each macvlan slave device to be in one
of three modes, depending on the use case:

MACVLAN_PRIVATE:
  The device never communicates with any other device
  on the same upper_dev. This even includes frames
  coming back from a reflective relay, where supported
  by the adjacent bridge.

MACVLAN_VEPA:
  The new Virtual Ethernet Port Aggregator (VEPA) mode,
  we assume that the adjacent bridge returns all frames
  where both source and destination are local to the
  macvlan port, i.e. the bridge is set up as a reflective
  relay.
  Broadcast frames coming in from the upper_dev get
  flooded to all macvlan interfaces in VEPA mode.
  We never deliver any frames locally.

MACVLAN_BRIDGE:
  We provide the behavior of a simple bridge between
  different macvlan interfaces on the same port. Frames
  from one interface to another one get delivered directly
  and are not sent out externally. Broadcast frames get
  flooded to all other bridge ports and to the external
  interface, but when they come back from a reflective
  relay, we don't deliver them again.
  Since we know all the MAC addresses, the macvlan bridge
  mode does not require learning or STP like the bridge
  module does.

Based on an earlier patch "macvlan: Reflect macvlan packets
meant for other macvlan devices" by Eric Biederman.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have very similar code for rx statistics in
two places in the macvlan driver, with a third
one being added in the next patch.

Consolidate them into one function to improve
overall readability of the driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The veth driver contains code to forward an skb
from the start_xmit function of one network
device into the receive path of another device.

Moving that code into a common location lets us
reuse the code for direct forwarding of data
between macvlan ports, and possibly in other
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Defaults to on (as before).
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The velocity hardware can handle up to 7 memory segments. This can be
turned on and off via ethtool. The support was removed in commit

  83c98a8c

but is re-enabled and cleaned up here. It's off by default.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VIA driver has changed the default for the DMA_LENGTH_DEF parameter.
Together with adaptive interrupt supression and NAPI support, this
improves performance quite a bit
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds NAPI support for VIA velocity. The new velocity_poll
function also pairs tx/rx handling twice which improves perforamance on
some workloads (e.g., netperf UDP_STREAM) significantly (that part is
from the VIA driver).
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

(Partially from the upstream VIA driver). Tweaking the number of
frames-per-interrupt and timer-until-interrupt can reduce the amount of
CPU work quite a lot.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

(From the VIA driver). The current code does not guarantee 64-byte
alignment since it simply does

        int add = skb->data & 63;

        skb->data += add;

(via skb_reserve). So for example, if the skb->data address would be
0x10, this would result in 32-byte alignment (0x10 + 0x10).

Correct by adding

        64 - (skb->data & 63)

instead.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

As side effect, consume less stack.

	-rtl8169_get_mac_version [vmlinux]:	432
	-rtl8169_init_one [vmlinux]:		376
	+rtl8169_init_one [vmlinux]:		136
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These algorithms use a truncation of 192/256 bits, as specified
in RFC4868.
Signed-off-by: Martin Willi <martin@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of using the hardcoded truncation for authentication
algorithms, use the truncation length specified on xfrm_state.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding a xfrm_state requires an authentication algorithm specified
either as xfrm_algo or as xfrm_algo_auth with a specific truncation
length. For compatibility, both attributes are dumped to userspace,
and we also accept both attributes, but prefer the new syntax.

If no truncation length is specified, or the authentication algorithm
is specified using xfrm_algo, the truncation length from the algorithm
description in the kernel is used.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new XFRMA_ALG_AUTH_TRUNC attribute taking a xfrm_algo_auth as
argument allows the installation of authentication algorithms with
a truncation length specified in userspace, i.e. SHA256 with 128 bit
instead of 96 bit truncation.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rewrite statistics accumulation to be in terms of structure fields,
not raw u32 additions. Keep them in same order, though.

This is the last user of create_proc_read_entry() in net/,
please NAK all new ones as well as all new ->write_proc, ->read_proc and
create_proc_entry() users. Cc me if there are problems. :-)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Generated with the following semantic patch

@@
struct net *n1;
struct net *n2;
@@
- n1 == n2
+ net_eq(n1, n2)

@@
struct net *n1;
struct net *n2;
@@
- n1 != n2
+ !net_eq(n1, n2)

applied over {include,net,drivers/net}.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define name tables for these enumerations in a similar way as for
loopback.  Move the loopback name table together with them.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All files that include ethtool.h, rx.h or tx.h are also including
efx.h, and there is no good reason to separate out the few
declarations they contain.  Therefore fold them into efx.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At some point these casts were used to remove const qualification, but
they are now unneeded.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is preparation for moving Falcon-specific state required by other
Falcon-specific code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename struct efx_board to struct falcon_board.

Introduce and use inline function to look up board info from struct
efx_nic, in preparation for moving it.

Move board init and fini calls into NIC probe and remove functions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

efx_board::init_leds was introduced as a second stage of
initialisation because of the inter-dependency between the board and
PHY.  We want to move board initialisation into NIC probing, which is
too early to use MDIO, so SFN4111T initialisation also needs to be
split.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only some PHYs have firmware support for a LED blink mode, so we
currently blink the others in a timer function.  Since all PHYs have
simple on and off modes, we don't gain anything by using multiple
blink implementations.  Also, since we have a process context there
is no need to use a timer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes the need to use a label and goto, and makes the two
branches mirror each other more closely.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function no longer has any common cleanup code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Finish the job by removing the structure member.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Copied from original one-line patch here:

	http://bugzilla.kernel.org/show_bug.cgi?id=14267#c26

(This is for 2.6.33 and beyond, where the bool was changed to a flag by
"cfg80211: convert bools into flags". -- JWL)
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The range check in the sprom image parser hex2sprom() is broken.
One sprom word is 4 hex characters.
This fixes the check and also adds much better sanity checks to the code.
We better make sure the image is OK by doing some sanity checks to avoid
bricking the device by accident.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>