Report REG00.IINLIM value as INPUT_CURRENT_LIMIT property.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Report configured precharge current.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Report charging type based on recently read state.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Edge interrupts from the charger may be lost or stuck in fault mode
since probe(). Check if something changed everytime userspace wants
some data.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Datasheet describes two modes for reading ADC measurements:
1. continuous, 1 Hz - enabled and started by CONV_RATE bit
2. one-shot - triggered by CONV_START bit

In continuous mode, CONV_START is read-only and signifies an ongoing
conversion.

Change the code to follow the datasheet and really disable continuous
mode for power saving.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Charge Current is more apropriately reflected by CURRENT_NOW property
(measured current) than CONSTANT_CURRENT_VOLTAGE (configured CC-phase
current limit). Fix the reference and make the sign reflect direction
of the current.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

According to the datasheet available at (1), the bottom four
bits are always zero and the actual voltage is 1.25x this value
in mV.  Since the kernel API specifies that voltages should be in
uV, it should report 1250x the shifted value.

1) https://datasheets.maximintegrated.com/en/ds/MAX17040-MAX17041.pdfSigned-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The framework is unhappy about them, because it uses the names in sysfs
attributes:

  power_supply olpc-ac: hwmon: 'olpc-ac' is not a valid name attribute, please fix
  power_supply olpc-battery: hwmon: 'olpc-battery' is not a valid name attribute, please fix

See also commit 648cd48c ("hwmon: Do not accept invalid name
attributes") and commit 74d3b641 ("hwmon: Relax name attribute
validation for new APIs").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

This delay-fix is picked up from downstream driver,
we measured that 25 - 35 ms delay ensure that we get required data.

Tested on SMB347 on Nexus 7 2012. Otherwise IRQSTAT_E fails to provide
correct information.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Fix failure when USB cable is connected:
smb347 2-006a: reading IRQSTAT_D failed

Fixes: 1502cfe1 ("smb347-charger: Fix battery status reporting logic for charger faults")
Tested-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The "default n" is not needed as it is, well, default. Clean
the KConfig by removing "default n".
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Indent the help text as explained in
Documentation/process/coding-style.rst
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The ROHM BD99954 is a Battery Management LSI for 1-4 cell Lithium-Ion
secondary battery intended to be used in space-constraint equipment such
as Low profile Notebook PC, Tablets and other applications. BD99954
provides a Dual-source Battery Charger, two port BC1.2 detection and a
Battery Monitor.

Support ROHM BD99954 Charger IC.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The ROHM BD99954 is a Battery Management LSI for 1-4 cell Lithium-Ion
secondary battery. Intended to be used in space-constraint equipment such
as Low profile Notebook PC, Tablets and other applications. BD99954
provides a Dual-source Battery Charger, two port BC1.2 detection and a
Battery Monitor.

Document the DT bindings for BD99954
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add parsing of new device-tree battery bindings.

     - trickle-charge-current-microamp
     - precharge-upper-limit-microvolt
     - re-charge-voltage-microvolt
     - over-voltage-threshold-microvolt
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add:

 - trickle-charge-current-microamp:

Some chargers have 3 charging stages. First one when battery is almost
empty is often called as trickle-charge. Last state when battery has been
"woken up" is usually called as fast-charge. In addition to this some
chargers have a 'middle state' which ROHM BD99954 data-sheet describes as
pre-charge. Some batteries can benefit from this 3-phase charging
[citation needed].

Introduce trickle-charge-current-microamp so that batteries can give
charging current limit for all three states.

 - precharge-upper-limit-microvolt:

When battery voltage has reached certain limit we change from
trickle-charge to next charging state (pre-charge for BD99954). Allow
battery to specify this limit.

 - re-charge-voltage-microvolt:

Allow giving a battery specific voltage limit for chargers which can
automatically re-start charging when battery has discharghed down to
this limit.

- over-voltage-threshold-microvolt

Allow specifying voltage threshold after which the battery is assumed to
be faulty.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Change the bd70528 to use common linear_range code instead of
implementing a copy of it in this driver.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

lib: Add linear ranges helper library and start using it

Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Fix gcc '-Wunused-but-set-variable' warning:
drivers/power/reset/ltc2952-poweroff.c:97:16: warning: variable
‘overruns’ set but not used [-Wunused-but-set-variable]
  unsigned long overruns;
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

In the probe function, in case of error, resources allocated in
'lp8788_setup_adc_channel()' must be released.

This can be achieved easily by using the devm_ variant of
'iio_channel_get()'.
This has the extra benefit to simplify the remove function and to axe the
'lp8788_release_adc_channel()' function which is now useless.

Fixes: 98a27664 ("power_supply: Add new lp8788 charger driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Modern device tree bindings are supposed to be created as YAML-files
in accordance with dt-schema. This commit replaces SYSCON reboot-mode
legacy bare text bindings with YAML file. As before the bindings file
states that the corresponding dts node is supposed to be compatible
"syscon-reboot-mode" device and necessarily have an offset property
to determine which register from the regmap is supposed to keep the
mode on reboot.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Fix the following warning:

drivers/power/supply/cw2015_battery.c:96:5: warning:
'cw_update_profile' was not declared. Should it be static?
drivers/power/supply/cw2015_battery.c:712:1: warning:
'cw_bat_pm_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ChenTao <chentao107@huawei.com>
Acked-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

We introduced some new locking here, but need to update the error
paths so they unlock before returning.

Fixes: 72d9cd9c ("power: bq25890: protect view of the chip's state")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Change the regulator helpers to use common linear_ranges code.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/64f01d5e381b8631a271616b7790f9d5640974fb.1588944082.git.matti.vaittinen@fi.rohmeurope.comSigned-off-by: Mark Brown <broonie@kernel.org>

Follow-up patches in this series will add a generic struct
linear_range. Rename bd70528 internal struct to avoid collision.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/286b1ae0adc1c08e7b644cbdc1a43eb2e0644647.1588944082.git.matti.vaittinen@fi.rohmeurope.comSigned-off-by: Mark Brown <broonie@kernel.org>

    Add a KUnit test for the linear_ranges helper.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Link: https://lore.kernel.org/r/311fea741bafdcd33804d3187c1642e24275e3e5.1588944082.git.matti.vaittinen@fi.rohmeurope.comSigned-off-by: Mark Brown <broonie@kernel.org>

Many devices have control registers which control some measurable
property. Often a register contains control field so that change in
this field causes linear change in the controlled property. It is not
a rare case that user wants to give 'meaningful' control values and
driver needs to convert them to register field values. Even more
often user wants to 'see' the currently set value - again in
meaningful units - and driver needs to convert the values it reads
from register to these meaningful units. Examples of this include:

- regulators, voltage/current configurations
- power, voltage/current configurations
- clk(?) NCOs

and maybe others I can't think of right now.

Provide a linear_range helper which can do conversion from user value
to register value 'selector'.

The idea here is stolen from regulator framework and patches refactoring
the regulator helpers to use this are following.

Current implementation does not support inversely proportional ranges
but it might be useful if we could support also inversely proportional
ranges?
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/59259bc475e0c800eb4bb163f02528c7c01f7b3a.1588944082.git.matti.vaittinen@fi.rohmeurope.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add POWER_SUPPLY_TYPE to the uevent env for power supply. Type is a
property of all power supplies and there is a sysfs entry for it but it
is not included in the properties array of the power supply so
explicitly add it to the udev env.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Reduce the number of touch points to add a new enum property to the
power_supply class by mapping the array of text values to the device
attribute descriptor. A new enum property can now added by creating an
array with the text values named POWER_SUPPLY_${PROPNAME}_TEXT and
adding POWER_SUPPLY_ENUM_ATTR(${PROPNAME}) to the power_supply_attrs
array.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Use designated initializers for the sysfs power supply text values. This
will help ensure that the text values are kept in sync with the enum
values from power_supply.h.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Make the device attribute list used to create sysfs attributes more
robust by decoupling the list order from order of the enum defined in
power_supply.h. This is done by using a designated initializer in the
POWER_SUPPLY_ATTR macro.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Extend bq->lock over whole updating of the chip's state. Might get
useful later for switching ADC modes correctly.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

regmap initialization will check I2C adapter functionality.
Remove redundant check in the driver.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Property list should not change, so mark it const.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Driver rejects unknown chips early in the probe(), so when
bq25890_power_supply_get_property() is made reachable, bq->chip_version
will already be set to correct value - there is no need to check
it again.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Pull more btrfs fixes from David Sterba:
 "A few more stability fixes, minor build warning fixes and git url
  fixup:

   - fix partial loss of prealloc extent past i_size after fsync

   - fix potential deadlock due to wrong transaction handle passing via
     journal_info

   - fix gcc 4.8 struct intialization warning

   - update git URL in MAINTAINERS entry"

* tag 'for-5.7-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  MAINTAINERS: btrfs: fix git repo URL
  btrfs: fix gcc-4.8 build warning for struct initializer
  btrfs: transaction: Avoid deadlock due to bad initialization timing of fs_info::journal_info
  btrfs: fix partial loss of prealloc extent past i_size after fsync

Pull IOMMU fixes from Joerg Roedel:

 - Fix a memory leak when dev_iommu gets freed and a sub-pointer does
   not

 - Build dependency fixes for Mediatek, spapr_tce, and Intel IOMMU
   driver

 - Export iommu_group_get_for_dev() only for GPLed modules

 - Fix AMD IOMMU interrupt remapping when x2apic is enabled

 - Fix error path in the QCOM IOMMU driver probe function

* tag 'iommu-fixes-v5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/qcom: Fix local_base status check
  iommu: Properly export iommu_group_get_for_dev()
  iommu/vt-d: Use right Kconfig option name
  iommu/amd: Fix legacy interrupt remapping for x2APIC-enabled system
  iommu: spapr_tce: Disable compile testing to fix build on book3s_32 config
  iommu/mediatek: Fix MTK_IOMMU dependencies
  iommu: Fix the memory leak in dev_iommu_free()

The git repo listed for btrfs hasn't been updated in over a year.
List the current one instead.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

This patch adds a driver for the CellWise cw2015 fuel gauge.

The CellWise cw2015 is a shuntless, single-cell Li-Ion fuel gauge used
in the pine64 Pinebook Pro laptop and some Raspberry Pi UPS HATs.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>