The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230724205456.767430-1-robh@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Property "trickle-resistor-ohms" allows us to set trickle charger
resistor. However there is no possibility to disable it afterwards.

Add support for "aux-voltage-chargeable" property which can be used to
enable/disable the trickle charger circuit explicitly. The default
behavior of the code is kept as it is!

Additionally, lets make sure we only update internal EEPROM in case of a
change. This prevents wear due to excessive EEPROM writes on each probe.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Link: https://lore.kernel.org/r/20230623081533.76334-1-andrej.picej@norik.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The added HAS_IOPORT dependency might not actually be necessary as Geert
points out, but the driver is also only used on one architecture. Sparc
is also a special case here since it converts port numbers into virtual
addresses rather than having them mapped into a particular part of the
__iomem address space, so the difference is actually not important here.

Add a dependency on sparc, but allow compile-testing otherwise, to
make this clearer without anyone having to spend much time modernizing
the driver beyond that.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/all/CAMuHMdWEx0F=fNei4Bz_JPkuvoaN-+zk08h0i8KnSi_VjO615g@mail.gmail.com/Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230719192835.1025406-1-arnd@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Drop enum pcf85063_type and split the array pcf85063_cfg[] as individual
variables, and make lines shorter by referring to e.g. &pcf85063_cfg
instead of &pcf85063_cfg[PCF85063].
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230717124059.196244-3-biju.das.jz@bp.renesas.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The pcf85063_ids[].driver_data could store a pointer to the config,
like for DT-based matching, making I2C and DT-based matching
more similar.

After that, we can simplify the probe() by replacing of_device_get_
match_data() and i2c_match_id() by i2c_get_match_data() as we have
similar I2C and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230717124059.196244-2-biju.das.jz@bp.renesas.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Simplify the probe() by replacing of_device_get_match_data() and
i2c_match_id() by i2c_get_match_data() as we have similar I2C
and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230710114747.106496-1-biju.das.jz@bp.renesas.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Fix a few style issues reported by checkpatch.pl:
- Unnecessary parentheses
- Lines should not end with a '('
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-8-valentin.caron@foss.st.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

stm32_rtc_valid_alrm function has some issues :
- arithmetical operations are impossible on BCD values
- "cur_mon + 1" can overflow
- the use case with the next month, the same day/hour/minutes went wrong

To solve that, we prefer to use timestamp comparison.
e.g. : On 5 Dec. 2021, the alarm limit is 5 Jan. 2022 (+31 days)
       On 31 Jan 2021, the alarm limit is 28 Feb. 2022 (+28 days)
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-7-valentin.caron@foss.st.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The RTC driver stops the RTCAPB clock during suspend, but the
irq handler from RTC is called before starting clock. Then we are
blocked while accessing RTC registers.

We changes PM callbacks to '_no_irq()' to disable irq during
resume callback and so irq handler will be called after the enable
of RTCAPB clock.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-6-valentin.caron@foss.st.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Change stm32-rtc driver to not generate an error message when
device probe operation is deferred for a clock.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-5-valentin.caron@foss.st.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The rtc is used to update the stgen counter on wake up from
low power modes, so it needs to be as much accurate as possible.

The maximization of asynchronous divider leads to a 4ms rtc
precision clock.
By decreasing pred_a to 0, it will have pred_s=32767 (when
need_accuracy is true), so stgen clock becomes more accurate
with 30us precision.
Nevertheless this will leads to an increase of power consumption.
Signed-off-by: Christophe Guibout <christophe.guibout@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-4-valentin.caron@foss.st.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

RTC counters are stopped when INIT bit in ISR register is set and
start counting from the (eventual) new value when INIT is reset.

In stm32_rtc_init(), called during probe, the INIT bit is set to
program the prescaler and the 24h mode. This halts the RTC counter
at each probe tentative causing the RTC time to loose from 0.3s to
0.8s at each kernel boot.
If the RTC is battery powered, both prescaler value and 24h mode
are kept during power cycle and there is no need to program them
again.

Check if the desired prescaler value and the 24h mode are already
programmed, then skip reprogramming them to avoid halting the time
counter.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-3-valentin.caron@foss.st.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Date and time are read from two separate RTC registers.
To ensure consistency between the two registers, reading the time
register locks the values in the shadow date register until the
date register is read.
Thus, the whole date/time read requires reading the time register
first, followed by reading the date register.
If the reads are done in reversed order, the shadow date register
will remain locked until a future read operation. The future read
will read the former date value that could be already invalid.

Fix the read order of date/time registers in stm32_rtc_valid_alrm()
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-2-valentin.caron@foss.st.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Add support for new NXP RTC PCF2131.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230622145800.2442116-18-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The PCF2127/29 do NOT support alarms with a 1 second resolution, but
the PCF2131 does.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-17-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The watchdog value register cannot be read on the PCF2131 after being
set.

Add a new flag to identify which variant has read access to this
register, and use this flag to selectively test if watchdog timer was
started by bootloader.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-16-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Introduce in the configuration structure two new values to hold the
watchdog clock source and the min_hw_heartbeat_ms value.

The minimum and maximum timeout values are automatically computed from
the watchdog clock source value for each variant.

The PCF2131 has no 1Hz watchdog clock source, as is the case for
PCF2127/29.

The next best choice is using a 1/4Hz clock, giving a watchdog timeout
range between 4 and 1016s. By using the same register configuration as
for the PCF2127/29, the 1/4Hz clock source is selected.

Note: the PCF2127 datasheet gives a min/max range between 1 and 255s,
but it should be between 2 and 254s, because the watchdog is triggered
when the timer value reaches 1, not 0.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-15-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The sequence for updating the time/date registers is slightly
different between PCF2127/29 and PCF2131.

For PCF2127/29, during write operations, the time counting
circuits (memory locations 03h through 09h) are automatically blocked.

For PCF2131, time/date registers write access requires setting the
STOP bit and sending the clear prescaler instruction (CPR). STOP then
needs to be released once write operation is completed.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-14-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The PCF2127 and PCF2129 have one output interrupt pin. The PCF2131 has
two, named INT_A and INT_B. The hardware support that any interrupt
source can be routed to either one or both of them.

Force all interrupt sources to go to the INT A pin.

Support to route any interrupt source to INT A/B pins is not supported
by this driver at the moment.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-13-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

This RTC is very similar in functionality to the PCF2127/29.

Basically it:
  -supports two new control registers at offsets 4 and 5
  -supports a new reset register (not implemented in this driver)
  -supports 4 tamper detection functions instead of 1
  -has no nvmem (like the PCF2129)
  -has two output interrupt pins

Because of that, most of the register addresses are very different,
although they still follow the same layout. For example, the tamper
registers have a different base address, but the offsets are all the same.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-12-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

This will simplify the implementation of new variants into this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-11-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

This will simplify the implementation of new variants into this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-10-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

This will simplify the implementation of new variants into this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Tested-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-9-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

This will simplify the implementation of new variants into this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-8-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

This will simplify the implementation of new variants into this driver.

Some variants (PCF2131) have a 100th seconds register. This register is
currently not supported in this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-7-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Create variant-specific configuration structures to simplify the
implementation of new variants into this driver. It will also avoid
to have too many tests for a specific variant, or a list of variants
for new devices, inside the code itself.

Add configuration options for the support of the NVMEM, bit CD0 in
register WD_CTL as well as the maximum number of registers for each
variant, instead of hardcoding the variant (PCF2127) inside the
i2c_device_id and spi_device_id structures.

Also specify a different maximum number of registers (max_register)
for the PCF2129.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-6-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Noted while reviewing new PCF2131 driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-5-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Noted while reviewing new PCF2131 driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-4-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Reading the 7 timetamp registers currently involves reading 25 registers
solely to be able to print the content of the three control registers,
in addition to the 7 timestamp registers. This print never occurs,
unless the user enables dynamic debug in this driver or set
CONFIG_RTC_DEBUG.

Reading the timestamp registers should consist of reading 7
consecutive timestamp registers.

This patch optimize the performance of reading the timestamp registers
by reading 7 consecutive registers instead of 25, and dropping the
print of the control registers.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-3-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Improve performance and readability of rtc_read_time() by reading only
the 7 time registers, instead of reading 8 registers (additional CTRL3
register).

We drop reading of CTRL3 to monitor the low battery flag, as this
check is already available in the ioctl. Anyway, this check only
display an info message and has no other impacts.

The code readability also improves as we do not have to fiddle with
buffer pointer and size arithmetic.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-2-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.

The answer is "No. No we cannot".

I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street.  And at the yearly
maintainer summit, we will all sing the alphabet song together.

I doubt I will keep doing this.  At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.

Repeats: 80e62bc8 ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull dma-mapping fixes from Christoph Hellwig:

 - swiotlb area sizing fixes (Petr Tesarik)

* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: reduce the number of areas to match actual memory pool size
  swiotlb: always set the number of areas before allocating the pool

Pull irq update from Borislav Petkov:

 - Optimize IRQ domain's name assignment

* tag 'irq_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqdomain: Use return value of strreplace()

Pull x86 fpu fix from Borislav Petkov:

 - Do FPU AP initialization on Xen PV too which got missed by the recent
   boot reordering work

* tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/xen: Fix secondary processors' FPU initialization

Pull x86 fix from Thomas Gleixner:
 "A single fix for the mechanism to park CPUs with an INIT IPI.

  On shutdown or kexec, the kernel tries to park the non-boot CPUs with
  an INIT IPI. But the same code path is also used by the crash utility.
  If the CPU which panics is not the boot CPU then it sends an INIT IPI
  to the boot CPU which resets the machine.

  Prevent this by validating that the CPU which runs the stop mechanism
  is the boot CPU. If not, leave the other CPUs in HLT"

* tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smp: Don't send INIT to boot CPU

Pull MIPS fixes from Thomas Bogendoerfer:

 - fixes for KVM

 - fix for loongson build and cpu probing

 - DT fixes

* tag 'mips_6.5_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled
  MIPS: dts: add missing space before {
  MIPS: Loongson: Fix build error when make modules_install
  MIPS: KVM: Fix NULL pointer dereference
  MIPS: Loongson: Fix cpu_probe_loongson() again

Pull xfs fix from Darrick Wong:
 "Nothing exciting here, just getting rid of a gcc warning that I got
  tired of seeing when I turn on gcov"

* tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix uninit warning in xfs_growfs_data

Pull more smb client updates from Steve French:

 - fix potential use after free in unmount

 - minor cleanup

 - add worker to cleanup stale directory leases

* tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Add a laundromat thread for cached directories
  smb: client: remove redundant pointer 'server'
  cifs: fix session state transition to avoid use-after-free issue

Pull NTB updates from Jon Mason:
 "Fixes for pci_clean_master, error handling in driver inits, and
  various other issues/bugs"

* tag 'ntb-6.5' of https://github.com/jonmason/ntb:
  ntb: hw: amd: Fix debugfs_create_dir error checking
  ntb.rst: Fix copy and paste error
  ntb_netdev: Fix module_init problem
  ntb: intel: Remove redundant pci_clear_master
  ntb: epf: Remove redundant pci_clear_master
  ntb_hw_amd: Remove redundant pci_clear_master
  ntb: idt: drop redundant pci_enable_pcie_error_reporting()
  MAINTAINERS: git://github -> https://github.com for jonmason
  NTB: EPF: fix possible memory leak in pci_vntb_probe()
  NTB: ntb_tool: Add check for devm_kcalloc
  NTB: ntb_transport: fix possible memory leak while device_register() fails
  ntb: intel: Fix error handling in intel_ntb_pci_driver_init()
  NTB: amd: Fix error handling in amd_ntb_pci_driver_init()
  ntb: idt: Fix error handling in idt_pci_driver_init()