checkpatch.pl complained about the line exceding 80 columns, and the
comment was actually on the same line as the code, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

instead of __attribute__((__aligned(size)__))
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bit 1 is the reset bit of the MAC status machine register, define and
use it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAC_RST bit is already defined, use it instead of 0x1 where applicable.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define more MCR0-register bits and use them in place of the bits values.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the conversion to phylib (3831861b: r6040: implement phylib) some
PHY-related variables and definitions are now useless, remove them.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should use an unique MDIO bus name which does not clash with anything
else in the system like the Fixed MDIO bus. The bus is now named:
r6040-<card number> which is unique in the system.
Reported-by: Vladimir Kolpakov <vova.kolpakov@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently Dave noticed that a test we did in ipv6_add_addr to see if we next hop
route for the interface we're adding an addres to was wrong (see commit
7ffbcecb).  for one, it never triggers, and two,
it was completely wrong to begin with.  This test was meant to cover this
section of RFC 4429:

3.3 Modifications to RFC 2462 Stateless Address Autoconfiguration

   * (modifies section 5.5) A host MAY choose to configure a new address
        as an Optimistic Address.  A host that does not know the SLLAO
        of its router SHOULD NOT configure a new address as Optimistic.
        A router SHOULD NOT configure an Optimistic Address.

This patch should bring us into proper compliance with the above clause.  Since
we only add a SLAAC address after we've received a RA which may or may not
contain a source link layer address option, we can pass a pointer to that option
to addrconf_prefix_rcv (which may be null if the option is not present), and
only set the optimistic flag if the option was found in the RA.

Change notes:
(v2) modified the new parameter to addrconf_prefix_rcv to be a bool rather than
a pointer to make its use more clear as per request from davem.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFQ q->perturbation is used in sfq_hash() as an input to Jenkins hash.

We currently randomize this 32bit value only if a perturbation timer is
setup.

Its much better to always initialize it to defeat attackers, or else
they can predict very well what kind of packets they have to forge to
hit a particular flow.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 817fb15d (net_sched: sfq: allow divisor to be a
parameter), we can leave perturbation timer armed if a memory allocation
error aborts sfq_init().

Memory containing active struct timer_list is freed and kernel can
crash.

Call sfq_destroy() from sfq_init() to properly dismantle qdisc.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All implementations have been converted to implement set_rxnfc
instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These new functions will support an implementation of the ethtool
RX NFC rules API.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Filter IDs are u32 (but never very large) so an ID/error return
value should have type s32.

Filter indices and search depths are never negative, so should
have type unsigned int.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also add note that the efx_filter_spec::priority field has nothing
to do with priority between multiple matching filters.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define special location values for RX NFC that request the driver to
select the actual rule location.  This allows for implementation on
devices that use hash-based filter lookup, whereas currently the API is
more suited to devices with TCAM lookup or linear search.

In ethtool_set_rxnfc() and the compat wrapper ethtool_ioctl(), copy
the structure back to user-space after insertion so that the actual
location is returned.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the driver only uses location values to maintain an ordered
list of filters.  Make it reject location values >= MAX_FILER_IDX
passed to the ETHTOOL_SRXCLSRLINS command, consistent with the range
it reports for the ETHTOOL_GRXCLSRLALL command.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Sebastian Pöhn <sebastian.poehn@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SMSC LAN generation 4 chips integrate an IEEE 802.3 ethernet physical layer.
The PHY driver for this integrated chip enable an energy detect power-down mode.
When the PHY is in a power-down mode, it prevents the MAC portion chip to be
software reseted.

That means that if we compile the kernel with the configuration option SMSC_PHY
enabled and try to bring the network interface up without an cable plug-ed the
PHY will be in a low power mode and the software reset will fail returning -EIO
to user-space:

root@igep00x0:~# ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error

This patch disable the energy detect power-down mode before trying to software
reset the LAN chip and re-enables after it was reseted successfully.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

SMSC generation 4 LAN chips integrate an IEEE 802.3 ethernet physical layer.
The ethernet driver for this family of devices needs to access the SMSC PHY
registers and bit-fields.

So, this patch moves these constants to a place where it can be used for both
the PHY and LAN drivers.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

Conflicts:
	drivers/net/wireless/b43/dma.c
	drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c

drivers/net/ethernet/marvell/skge.c:4046: warning: ‘skge_suspend’ defined but not used
drivers/net/ethernet/marvell/skge.c:4071: warning: ‘skge_resume’ defined but not used
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver uses a shared pool for both rx and tx descriptors.
During open it queues fixed number of 128 descriptors for receive
packets. For each received packet it tries to queue another
descriptor. If this fails the descriptor is lost for rx.
The driver has no limitation on tx descriptors to use, so it
can happen during a nmap / ping -f attack that the driver
allocates all descriptors for tx and looses all rx descriptors.
The driver stops working then.
To fix this limit the number of tx descriptors used to half of
the descriptors available, the rx path uses the other half.

Tested on a custom board using nmap / ping -f to the board from
two different hosts.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When trying to allocate ~32768 qdiscs using autohandle mechanism, we can
fill the space managed by kernel (handles in [8000-FFFF]:0000 range)

But O(N^2) qdisc_alloc_handle() loops 0x10000 times instead of 0x8000

time tc add qdisc add dev eth0 parent 10:7fff pfifo limit 10
RTNETLINK answers: Cannot allocate memory
real    1m54.826s
user    0m0.000s
sys     0m0.004s

INFO: rcu_sched_state detected stall on CPU 0 (t=60000 jiffies)

Half number of loops, and add a cond_resched() call.
We hold rtnl at this point.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can underestimate q->wsum in case of "tc class replace ... qfq"
and/or qdisc_create_dflt() error.

wsum is not really used in fast path, only at qfq qdisc/class setup,
to catch user error.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFQ enqueue algo puts a new flow _behind_ all pre-existing flows in the
circular list. In fact this is probably an old SFQ implementation bug.

100 Mbits = ~8333 full frames per second, or ~8 frames per ms.

With 50 flows, it means your "new flow" will have to wait 50 packets
being sent before its own packet. Thats the ~6ms.

We certainly can change SFQ to give a priority advantage to new flows,
so that next dequeued packet is taken from a new flow, not an old one.
Reported-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Showing which capabilities are not passed to VF
when executing QUERY_PORT
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mtt range was allocated in mtt units but deallocated
in segments. Among the rest, this caused crash during hotplug removal
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If slave device already has a receive handler registered, then the
error unwind of bonding device enslave function is broken.

The following will leave a pointer to freed memory in the slave
device list, causing a later kernel panic.
# modprobe dummy
# ip li add dummy0-1 link dummy0 type macvlan
# modprobe bonding
# echo +dummy0 >/sys/class/net/bond0/bonding/slaves

The fix is to detach the slave (which removes it from the list)
in the unwind path.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rx mode should be reset after resming, so unconditionally updating rx
mode rather than conditionally updating based on the value we
remembered, otherwise unexpected value may be used by the nic after
resuming.

btw. I find and test this when debugging guest hibernation in qemu, as
I did not have a 8139cp card in hand, this patch is untested in a
physical 8139cp card, plase review it carefully.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

delay_eeprom() use long read for Cfg9346 register(offset 0x50) which may read
into the area of reserved register(offset 0x53). Use byte read instead.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This device uses an already existing DevID but since it supports
WoL we need to add the Sub DevID.  It's support of WoL is limited
to the first port.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Support for new 82599 based quad port adapter.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

I2C access is timing critical. Always do a write flush after writing
to the I2CCTL register.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Saw typo in one message, so decided to run spell checker.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix some register reads that had the opcode and register parameters swapped.
Also use define instead of a magic (0x3) number.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Added pause flag for bi-directional flow control advertising to ethtool
settings.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to address possible issues with the IXGBEVF register
defines generating incorrect values when given a complex expression for the
register offset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>