Also remove the code using size-0 OUTPUT buffer to flush.
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Wu-Cheng Li <wuchengli@chromium.org>
Reviewed-by: Kuang-che Wu <kcwu@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

gcc isn't smart enough to realize it can share most of the argument
buildup and the actual function call between the two branches, so help
it a little.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

It takes more .text to initialize these on the stack than they occupy
in .rodata, so just make them static const.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

ibuf and rbuf in lme2510_int_response are always assigned to before they
are read, and their addresses do not escape the function, so they have
no reason to be static.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Using the %ph printf extension for hex dumps like this makes the
generated code quite a bit smaller.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Drivers might try to access and run enable_source and disable_source
handlers when the driver that implements these handlers is clearing
the handlers during its unregister.

Fix the following race condition:

process 1				process 2

request video streaming			unbind au0828
v4l2 checks if tuner is free
...					...

					au0828_unregister_media_device()
...					...
					(doesn't hold graph_mutex)
					mdev->enable_source = NULL;
if (mdev && mdev->enable_source)	mdev->disable_source = NULL;
	mdev->enable_source()
(enable_source holds graph_mutex)

As shown above enable_source check is done without holding the graph_mutex.
If unbind happens to be in progress, au0828 could clear enable_source and
disable_source handlers leading to null pointer de-reference.

Fix it by protecting enable_source and disable_source set and clear and
protecting enable_source and disable_source handler access and the call
itself.

process 1				process 2

request video streaming			unbind au0828
v4l2 checks if tuner is free
...					...

					au0828_unregister_media_device()
...					...
					(hold graph_mutex while clearing)
					mdev->enable_source = NULL;
if (mdev)				mdev->disable_source = NULL;
(hold graph_mutex to check and
 call enable_source)
    if (mdev->enable_source)
	mdev->enable_source()

If graph_mutex is held to just heck for handler being null and needs to be
released before calling the handler, there will be another window for the
handlers to be cleared. Hence, enable_source and disable_source handlers
no longer hold the graph_mutex and expect callers to hold it to avoid
forcing them release the graph_mutex before calling the handlers.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Using sprintf() with a non-literal string makes some compiler complain
when building with -Wformat-security (eg. clang reports "format string
is not a string literal (potentially insecure)").

Here sprintf() format parameter is indirectly a literal string so there
is no security issue.  Nevertheless adding a "%s" format string to
silent the warning helps to detect real bugs in the kernel.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The check assumes that we end on zero but actually we end on -1.  Change
the post-op to a pre-op so that we do end on zero.  Techinically now we
only loop 499 times instead of 500 but that's fine.

Fixes: dc12b124 ("[media] media: ti-vpe: vpdma: Add abort channel desc and cleanup APIs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Fix to avoid possible memory leak if the decoder initialization got failed.
Free the allocated memory for file handle object before return in case
decoder initialization fails.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The FE_SUPPORTED() macro is basically the same as IS_REACHABLE, except
that it causes a warning with gcc-7:

common/b2c2/flexcop-fe-tuner.c:30:1: error: this use of "defined" may not be portable [-Werror=expansion-to-defined]
common/b2c2/flexcop-fe-tuner.c:30:1: error: this use of "defined" may not be portable [-Werror=expansion-to-defined]
common/b2c2/flexcop-fe-tuner.c:30:1: error: this use of "defined" may not be portable [-Werror=expansion-to-defined]

Using IS_REACHABLE() to define it avoids the warning.

Fixes: 3785bc17 ("[media] b2c2: break it into common/pci/usb directories")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

changeset da8ec560 ("[media] ivtv: implement new decoder command
ioctls") implemented proper support for mpeg audio and video control
at V4L2 API. Since then, the usage of the the DVB APIs is deprecated.

However, we never actually marked it as deprecated nor provided any
way to disable it. Let's do it now.

This patch prepares for the removal of this bad usage on a couple
of Kernel versions.

Fixes: da8ec560 ("[media] ivtv: implement new decoder command ioctls")
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Remove unused demod driver. Device that used it never went public.

If someone later decide to add support for a device using this
chipset, it should be easy enough to retrieve it from git
history.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

I saw from ZyDAS ZD1301 sniffs it sets chip sleeping by using
REG_MISC_CTRL. That has very huge effect for power management, around
0.9W. Sleep is still disabled for all the old hardware just to avoid
possible regression as meaning of register bits are unknown.

I tested it also with some other devices and it seems to be working,
but I still consider it to be too risky to change it default.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

DVB USB interface driver for ZyDAS ZD1301 chip.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

ZyDAS ZD1301 is chip having USB interface and DVB-T demodulator
integrated. This driver is for USB interface part.

Device has USB ID 0ace:13a1. Used tuner is MT2060.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

DVB-T demodulator driver for ZyDAS ZD1301 chip.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

ZyDAS ZD1301 is chip having USB interface and DVB-T demodulator
integrated. This driver is for demodulator part.
Driver is very reduced, just basic demodulator functionality, no
statistics at all. It registers as a platform driver to driver core.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add configuration parameter to split long i2c writes as some I2C
adapters cannot write 10 bytes used as a one go.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add proper i2c driver model bindings.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

pr_foo() provides a convenient way for printk's, enforcing
that they'll all prepend the error message with the driver's
name.

Use it inside ivtv.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Move the pr_fmt() macro to ivtv_driver.h and ensure that it
will be the first file to be included on all ivtv files.

While here, put the includes inside ivtv-driver.h on
alphabetic order.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

As reported by gcc:

drivers/media/platform/sti/hva/hva-v4l2.c:227:6: warning: no previous prototype for 'hva_dbg_summary' [-Wmissing-prototypes]
 void hva_dbg_summary(struct hva_ctx *ctx)
      ^~~~~~~~~~~~~~~

This function is used only internally, so make it static.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

This patch creates 4 static debugfs entries to dump:
- the device-related information ("st-hva/device")
- the list of registered encoders ("st-hva/encoders")
- the current values of the hva registers ("st-hva/regs")
- the information about the last closed instance ("st-hva/last")

It also creates dynamically a debugfs entry for each opened instance,
("st-hva/<instance identifier>") to dump:
- the information about the frame (format, resolution)
- the information about the stream (format, profile, level,
  resolution)
- the control parameters (bitrate mode, framerate, GOP size...)
- the potential (system, encoding...) errors
- the performance information about the encoding (HW processing
  duration, average bitrate, average framerate...)
Each time a running instance is closed, its context (including the
debug information) is saved to feed, on demand, the last closed
instance debugfs entry.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

This patch adds a short summary about the encoding operation at each
instance closing, for debug purpose (through dev_dbg()):
- information about the frame (format, resolution)
- information about the stream (format, profile, level, resolution)
- number of encoded frames
- potential (system, encoding...) errors
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 25ms delays here to use msleep() and
reduce the load on the hrtimer subsystem.

Link: http://lkml.org/lkml/2017/1/11/377Reviwed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The gpiod API checks for NULL descriptors, there's no need to duplicate
the check in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Despite checkpatch comments, it seems that ARM doesn't like
to use constified structs.

As reported by kernel build robot:

 In file included from drivers/media/platform/coda/imx-vdoa.c:22:0:
   drivers/media/platform/coda/imx-vdoa.c: In function 'vdoa_driver_init':
>> include/linux/device.h:1461:20: warning: passing argument 1 of '__platform_driver_register' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
     return __register(&(__driver) , ##__VA_ARGS__); \
                       ^
   include/linux/platform_device.h:198:29: note: in definition of macro 'platform_driver_register'
     __platform_driver_register(drv, THIS_MODULE)
                                ^~~
   include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
     module_driver(__platform_driver, platform_driver_register, \
     ^~~~~~~~~~~~~
>> drivers/media/platform/coda/imx-vdoa.c:333:1: note: in expansion of macro 'module_platform_driver'
    module_platform_driver(vdoa_driver);
    ^~~~~~~~~~~~~~~~~~~~~~
   include/linux/platform_device.h:199:12: note: expected 'struct platform_driver *' but argument is of type 'const struct platform_driver *'
    extern int __platform_driver_register(struct platform_driver *,
               ^~~~~~~~~~~~~~~~~~~~~~~~~~
   In file included from drivers/media/platform/coda/imx-vdoa.c:18:0:
   drivers/media/platform/coda/imx-vdoa.c: In function 'vdoa_driver_exit':
>> include/linux/device.h:1466:15: warning: passing argument 1 of 'platform_driver_unregister' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
     __unregister(&(__driver) , ##__VA_ARGS__); \
                  ^
   include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
     module_driver(__platform_driver, platform_driver_register, \
     ^~~~~~~~~~~~~
>> drivers/media/platform/coda/imx-vdoa.c:333:1: note: in expansion of macro 'module_platform_driver'
    module_platform_driver(vdoa_driver);
    ^~~~~~~~~~~~~~~~~~~~~~
   In file included from drivers/media/platform/coda/imx-vdoa.c:22:0:
   include/linux/platform_device.h:201:13: note: expected 'struct platform_driver *' but argument is of type 'const struct platform_driver *'
    extern void platform_driver_unregister(struct platform_driver *);
                ^~~~~~~~~~~~~~~~~~~~~~~~~~

So, let's just remove it.

This reverts commit 126f52b0.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Both functions initialize the file handle with v4l2_fh_init() and thus
need to call clean up with v4l2_fh_exit() as appropriate. Fix it.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Both functions initialize the file handle with v4l2_fh_init() and thus
need to call clean up with v4l2_fh_exit() as appropriate. Fix it.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The device driver should keep going even if debugfs initialization fails.
So, change the return type to void.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Don't mix up UVC_BUF_STATE_* and VB2_BUF_STATE_* codes.

Fixes: 6998b6fb ("[media] uvcvideo: Use videobuf2-vmalloc")

Cc: stable@vger.kernel.org
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Remove a superfluous assignment to a local variable at the end of a
function.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add an inline function to obtain a struct uvc_buffer pointer from a
struct vb2_v4l2_buffer one.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Use formulas for cnr estimates and get rid of old lut-based estimate.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Chip uses so called 8-bit i2c addresses, but on bus there is of
course correct 7-bit addresses with rw bit as lsb - verified
with oscilloscope.

Lets still use correct addresses in driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Driver supports 2 different device versions, AX and BX. Use device
IDs to pass chip version information to driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

it913x tuner driver is changed to platform model so we need bind it
using platform_device_register_data().

Also remove hacks from I2C adapter where fake tuner driver address
(addr >> 1) were used as those are no longer needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

That tuner is integrated to demodulator and communicates via
demodulators address space. We cannot register both demodulator
and tuner having same address to same I2C bus, so better to change
it platform driver in order to implement I2C adapter correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

IT9130 series contains integrated tuner driver, which uses that
demodulator address space. Return regmap in order to allow it913x
driver communication.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Fix coding style and other small issues.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>