- 12 Feb, 2019 18 commits
-
-
Nir Dotan authored
The LAG port collecting (receive) function was mistakenly set when the port was registered as a LAG member, while it should be set only when the port collection state is set to true. Set LAG port to collecting when it is set to distributing, as described in the IEEE link aggregation standard coupled control mux machine state diagram. Signed-off-by: Nir Dotan <nird@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Ursula Braun says: ==================== net/smc: patches 2019-02-12 here are patches for SMC: * patches 1 and 3 optimize SMC-R tx logic * patch 2 is a cleanup without functional change * patch 4 optimizes rx logic * patches 5 and 6 improve robustness in link group and IB event handling * patch 7 establishes Karsten Graul as another SMC maintainer ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ursula Braun authored
Add Karsten as additional maintainer for Shared Memory Communications (SMC) Sockets. Acked-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Karsten Graul authored
For robustness protect of higher port numbers than expected to avoid setting bits behind our port_event_mask. In case of an DEVICE_FATAL event all ports must be checked. The IB_EVENT_GID_CHANGE event is provided in the global event handler, so handle it there. And handle a QP_FATAL event instead of an DEVICE_FATAL event in the qp handler. Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Karsten Graul authored
Remove the shortcut that smc_lgr_free() would skip the check for existing connections when the link group is not in the link group list. Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Karsten Graul authored
In smc_cdc_msg_recv_action() the received cdc message is evaluated. To reduce the number of messaged triggered by this evaluation the logic is streamlined. For the write_blocked condition we do not need to send a response immediately. The remaining conditions can be put together into one if clause. Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Karsten Graul authored
When no free transfer buffers are available then a work to call smc_tx_work() is scheduled. Set the schedule delay to zero, because for the out-of-buffers condition the work can start immediately and will block in the called function smc_wr_tx_get_free_slot(), waiting for free buffers. Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Karsten Graul authored
Move the call to smc_close_wake_tx_prepared() (which wakes up a possibly waiting close processing that might wait for 'all data sent') to smc_tx_sndbuf_nonempty() (which is the main function to send data). Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Karsten Graul authored
When an updated rx_cursor_confirmed field was sent to the peer then reset the cons_curs_upd_req flag. And remove the duplicate reset and cursor update in smc_tx_consumer_update(). Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
Recent cls_flower offload rewrite added a double new line. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eli Britstein authored
Implementation of macro "flow_action_for_each" introduced in commit e3ab786b ("flow_offload: add flow action infrastructure") and used in commit 73867881 ("drivers: net: use flow action infrastructure") iterated the first item twice and did not reach the last one. Fix it. Fixes: e3ab786b ("flow_offload: add flow action infrastructure") Fixes: 73867881 ("drivers: net: use flow action infrastructure") Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Randy Dunlap authored
Fix markup warnings for one list by using correct list syntax. Fix markup warnings for another list by using blank lines before the list. Documentation/networking/device_drivers/freescale/dpaa2/dpio-driver.rst:30: WARNING: Unexpected indentation. Documentation/networking/device_drivers/freescale/dpaa2/dpio-driver.rst:143: WARNING: Unexpected indentation. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Stuart Yoder <stuyoder@gmail.com> Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com> Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com> Cc: netdev@vger.kernel.org Cc: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Jakub Kicinski says: ==================== devlink: minor tweaks to reported device info This series contains two minor touch ups for devlink code. First || is corrected to && in the ethtool compat code. Next patch decreases the stack allocation size. On the nfp side after further discussions with the manufacturing team we decided to realign the serial number contents slightly and rename one of the other fields from "vendor" to "mfr", short for "manufacture". v2: - add patch 3 - move board maker as a generic attribute. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
The manufacturing team requests we include vendor and product in the serial number field, as the serial number itself is not unique across manufacturing facilities and products. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
Vendor may sound ambiguous, let's rename the fab string to "board.manufacture" (which was just added as a generic identifier). Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
At Jiri's suggestion add a generic "board.manufacture" version identifier. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
Number of devlink attributes has grown over 128, causing the following warning: ../net/core/devlink.c: In function ‘devlink_nl_cmd_region_read_dumpit’: ../net/core/devlink.c:3740:1: warning: the frame size of 1064 bytes is larger than 1024 bytes [-Wframe-larger-than=] } ^ Since the number of attributes is only going to grow allocate the array dynamically. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
We need the port to be both ethernet and have the rigth netdev, not one or the other. Fixes: ddb6e99e ("ethtool: add compat for devlink info") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 11 Feb, 2019 2 commits
-
-
Parav Pandit authored
Add WARN_ON to make sure that all sub objects of a devlink device are cleanedup before freeing the devlink device. This helps to catch any driver bugs. Signed-off-by: Parav Pandit <parav@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Tristram Ha authored
The flag offload_fwd_mark is set as the switch can forward frames by itself. This can be considered a fix to a problem introduced in commit c2e86691 where the port membership are not set in sync. The flag offload_fwd_mark just needs to be set in tag_ksz.c to prevent the software bridge from forwarding duplicate multicast frames. Fixes: c2e86691 ("microchip: break KSZ9477 DSA driver into two files") Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 10 Feb, 2019 10 commits
-
-
David S. Miller authored
Heiner Kallweit says: ==================== net: phy: add and use register modifying helpers returning 1 on change Add and use register modifying helpers returning 1 on change. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Use phy_modify_changed() to simplify the code. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
When replacing mv3310_modify() with phy_modify_mmd() we missed that they behave differently, mv3310_modify() returns 1 on a changed register value whilst phy_modify_mmd() returns 0. Fix this by replacing phy_modify_mmd() with phy_modify_mmd_changed() where needed. Fixes: b52c018d ("net: phy: make use of new MMD accessors") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
When modifying registers there are scenarios where we need to know whether the register content actually changed. This patch adds new helpers to not break users of the current ones, phy_modify() etc. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Eli Cohen says: ==================== Change tc action identifiers to be more consistent This two patch series modifies TC actions identifiers to be more consistent and also puts them in one place so new identifiers numbers can be chosen more easily. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eli Cohen authored
Modify the kernel users of the TCA_ACT_* macros to use TCA_ID_*. For example, use TCA_ID_GACT instead of TCA_ACT_GACT. This will align with TCA_ID_POLICE and also differentiates these identifier, used in struct tc_action_ops type field, from other macros starting with TCA_ACT_. To make things clearer, we name the enum defining the TCA_ID_* identifiers and also change the "type" field of struct tc_action to id. Signed-off-by: Eli Cohen <eli@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eli Cohen authored
Move all the TC identifiers to one place, to the same enum that defines the identifier of police action. This makes it easier choose numbers for new actions since they are now defined in one place. We preserve the original values for binary compatibility. New IDs should be added inside the enum. Signed-off-by: Eli Cohen <eli@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nikita Yushchenko authored
Add support for the AQCS109. From software point of view, it should be almost equivalent to AQR107. v2: - make Nikita the author - document what I changed Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> [hkallweit1@gmail.com: use PHY_ID_MATCH_MODEL mascro] Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
By using an external PHY, ports 9 and 10 can support 2500BaseT. So set this link mode in the mask when validating. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
yupeng authored
add document for tcp retransmission, tcp fast open, syn cookies, challenge ack, prune and several general counters Signed-off-by: yupeng <yupeng0921@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 09 Feb, 2019 10 commits
-
-
Russell King authored
When mvpp2 configures the flow control modes in mvpp2_xlg_config() for 10G mode, it only ever set the flow control enable bits. There is no mechanism to clear these bits, which means that userspace is unable to use standard APIs to disable flow control (the only way is to poke the register directly.) Fix the missing bit clearance to allow flow control to be disabled. This means that, by default, as there is no negotiation in 10G modes with mvpp2, flow control is now disabled rather than being rx-only. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
Add support for runtime determination of what the PHY supports, by adding a new function to the phy driver. The get_features call should set the phydev->supported member with the features the PHY supports. It is only called if phydrv->features is NULL. This requires minor changes to pause. The PHY driver should not set pause abilities, except for when it has odd cause capabilities, e.g. pause cannot be disabled. With this change, phydev->supported already contains the drivers abilities, including pause. So rather than considering phydrv->features, look at the phydev->supported, and enable pause if neither of the pause bits are already set. Signed-off-by: Andrew Lunn <andrew@lunn.ch> [hkallweit1@gmail.com: fixed small checkpatch complaint in one comment] Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
We will soon support asking the PHY at runtime to determine what features it supports, rather than forcing it to be compile time. But we should probe the PHY first. So probe the phy driver earlier. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
PHY registers are only 16 bits wide, therefore, if the read was successful, there's no need to mask out the higher 16 bits. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vakul Garg authored
Function tls_sw_recvmsg() dequeues multiple records from stream parser and decrypts them. In case the decryption is done by async accelerator, the records may get submitted for decryption while the previous ones may not have been decryted yet. For tls1.3, the record type is known only after decryption. Therefore, for tls1.3, tls_sw_recvmsg() may submit records for decryption even if it gets 'handshake' records after 'data' records. These intermediate 'handshake' records may do a key updation. By the time new keys are given to ktls by userspace, it is possible that ktls has already submitted some records i(which are encrypted with new keys) for decryption using old keys. This would lead to decrypt failure. Therefore, async decryption of records should be disabled for tls1.3. Fixes: 130b392c ("net: tls: Add tls 1.3 support") Signed-off-by: Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Bit 0 in register 1.5 doesn't represent a device but is a flag that Clause 22 registers are present. Therefore disregard this bit when populating the device list. If code needs this information it should read register 1.5 directly instead of accessing the device list. Because this bit doesn't represent a device don't define a MDIO_MMD_XYZ constant, just define a MDIO_DEVS_XYZ constant for the flag in the device list bitmap. v2: - make masking of bit 0 more explicit - improve commit message Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Russell King says: ==================== mvpp2 phylink fixes Having spent a while debugging issues with Sven Auhagen, it appears that the mvpp2 network driver's phylink support isn't quite correct. This series fixes that up, but, despite being tested locally, by Sven, and by Antoine, I would prefer it to be applied to net-next so that there is time for more people to test before it hits -rc or stable backports. The symptoms were that although PHYs would come up, the GMAC never reported that the link was up, or in some cases it did report link up but packets would not flow. Various approaches were tried to work around that, such as switching to in-band negotiation from PHY mode, but ultimately the problem was in the way mvpp2 was being programmed. This series addresses that by, essentially, making mvpp2 follow the same implementation pattern as mvneta: we configure the GMAC in three stages: 1) the PHY interface mode 2) the negotiation advert 3) the negotiation style Another issue is that mvpp2 was always taking the link down each time its mac_config method was called: this is disruptive when the link is already up, and we're just updating settings such as flow control. There are some circumstances where we make the call despite there being no changes (eg, when phylink is polling a GPIO or using a custom link state function.) This series depends on two previous patches already sent for net-next: net: marvell: mvpp2: fix lack of link interrupts net: marvell: mvpp2: use phy_interface_mode_is_8023z() helper There is one last patch which deals with link status interrupts, which I'll send separately because I think there's other considerations, but that should not hold up this series of patches. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Russell King authored
phylink already limits which interface modes are able to call the MACs AN restart function, but in any case, the commentry seems incorrect: the AN restart bit does not automatically clear when set. This has been found via manual setting using devmem2, and we can observe that the AN does indeed restart and complete, yet the AN restart bit remains set. Explicitly clear the AN restart bit. Tested-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Russell King authored
When reading the pause bits in mac_link_state, mvpp2 was reporting the state of the "active pause" bits, which are set when the MAC is in pause mode. This is not what phylink wants - we want the negotiated pause state. Fix the definition so we read the correct bits. Tested-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Russell King authored
mac_config() can be called at any point, and the expected behaviour from MAC drivers is to only reprogram when necessary - and certainly avoid taking the link down on every call. Unfortunately, mvpp2 does exactly that - it takes the link down, and reprograms everything, and then releases the forced-link down. This is bad, it can cause the link to bounce: - SFP detects signal, disables LOS indication. - SFP code calls into phylink, calling phylink_sfp_link_up() which triggers a resolve. - phylink_resolve() calls phylink_get_mac_state() and finds the MAC reporting link up. - phylink wants to configure the pause mode on the MAC, so calls phylink_mac_config() - mvpp2 takes the link down temporarily, generating a MAC link down event followed by another MAC link event. - phylink calls mac_link_up() and then processes the MAC link down event. - phylink_resolve() gets called again, registers the link down, and calls mach_link_down() before re-running itself. - phylink_resolve() starts again at step 3 above. This sequence repeats. GMAC versions prior to mvpp2 do not require the link to be taken down except when certain link properties (eg, switching between SGMII and 1000base-X mode, or enabling/disabling in-band negotiation) are changed. Implement this for mvpp2. Tested-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
-