With the system coprocessor managing the range allocation of the
inputs to Interrupt Aggregator, it is difficult to represent
the device IRQs from DT.

The suggestion is to use MSI in such cases where devices wants
to allocate and group interrupts dynamically.

Create a MSI domain bus layer that allocates and frees MSIs for
a device.

APIs that are implemented:
- ti_sci_inta_msi_create_irq_domain() that creates a MSI domain
- ti_sci_inta_msi_domain_alloc_irqs() that creates MSIs for the
  specified device and resource.
- ti_sci_inta_msi_domain_free_irqs() frees the irqs attached to the device.
- ti_sci_inta_msi_get_virq() for getting the virq attached to a specific event.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Texas Instruments' K3 generation SoCs has an IP Interrupt Aggregator
which is an interrupt controller that does the following:
- Converts events to interrupts that can be understood by
  an interrupt router.
- Allows for multiplexing of events to interrupts.

Configuration of the interrupt aggregator registers can only be done by
a system co-processor and the driver needs to send a message to this
co processor over TISCI protocol. Add the required infrastructure to
allow the allocation and routing of these events.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Add the DT binding documentation for Interrupt Aggregator driver.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Texas Instruments' K3 generation SoCs has an IP Interrupt Router
that does allows for redirection of input interrupts to host
interrupt controller. Interrupt Router inputs are either from a
peripheral or from an Interrupt Aggregator which is another
interrupt controller.

Configuration of the interrupt router registers can only be done by
a system co-processor and the driver needs to send a message to this
co processor over TISCI protocol.

Add support for Interrupt Router driver over TISCI protocol.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Add the DT binding documentation for Interrupt router driver.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

thunderx_gpio_irq_{request,release}_resources apis are trying to
{request,release} resources on parent interrupt. There are default
apis doing the same. Use the default parent apis instead of writing
the same code snippet.

Cc: linux-gpio@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Introduce irq_chip_{request,release}_resource_parent() apis so
that these can be used in hierarchical irqchips.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Each resource with in the device can be uniquely identified as defined
by TISCI. Since this is generic across the devices, resource allocation
also can be made generic instead of each client driver handling the
resource. So add helper apis to manage the resource.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Add the resource mapping table for AM654 SoC as defined in
http://downloads.ti.com/tisci/esd/latest/5_soc_doc/am6x/resasg_types.html
Introduce a new compatible for AM654 "ti,am654-sci" for using
this resource map table.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

TISCI abstracts the handling of IRQ routes where interrupt sources
are not directly connected to host interrupt controller. Add support
for the set of TISCI commands for requesting and releasing IRQs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

TISCI provides support for getting the resources(IRQ, RING etc..)
assigned to a specific device. These resources can be handled by
the client and in turn sends TISCI cmd to configure the resources.

It is very important that client should keep track on usage of these
resources.

Add support for TISCI commands to get resource ranges.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

TISCI has been updated to have support for Resource management(like
interrupts etc..). And there can be multiple device instances of a
resource type in a SoC. So every driver corresponding to a resource type
should get a TISCI handle so that it can make TISCI calls. And each
DT node corresponding to a device should exist under its corresponding
bus node as per the SoC architecture.

But existing apis in TISCI library assumes that all TISCI users are
child nodes of TISCI. Which is not true in the above case. So introduce
(devm_)ti_sci_get_by_phandle() apis that can be used by TISCI users
to get TISCI handle using of phandle property.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

There is no need to print a message if devm_kzalloc() fails, as the
memory allocation core already takes care of that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

IRQ_DOMAIN_HIERARCHY selects IRQ_DOMAIN, hence there is no need for
drivers to select both.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Using list_add + list_sort to insert an element and keeping the list
sorted is a somewhat blunt instrument; one can find the right place to
insert in fewer lines of code than the cmp callback uses. Moreover,
walking the entire list afterwards to merge adjacent ranges is
overkill, since we know that only the just-inserted element may be
merged with its neighbours.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

There's no reason to ask kmalloc() to zero the allocation, since all
the fields get initialized immediately afterwards. Except that there's
also not any reason to initialize the ->entry member, since the
element gets added to the lpi_range_list immediately.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

There's no reason to do the allocation of the new lpi_range inside the
lpi_range_lock. One could change the code to avoid the allocation
altogether in case the freed range can be merged with one or two
existing ranges (in which case the allocation would naturally be done
under the lock), but it's probably not worth complicating the code for
that.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

This irqchip driver uses the hwspinlock framework (coprocessor HW regs
access concurrency) for the stm32mp1-exti device.
Hence, this driver needs to handle the hwspinlock driver dependency
using the deferred probe mechanism which requires to move this driver
into a platform one with a probe() ops.
This applies only for the device which is "st,stm32mp1-exti" compatible,
the management of the other devices (st,stm32h7-exti / st,stm32-exti) is
kept unchanged (use IRQCHIP_DECLARE)
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

If interrupts are enabled for a non-root GIC device that uses the
gic-pm driver, when system suspend occurs, the current interrupt
state is not saved and restored correctly and so interrupts do not
work again on resuming the system. Add a late suspend handler to
save and restore the state for these devices.
Suggested-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

gic-pm driver is using pm-clk framework to manage clock resources, where
clocks remain always ON. This happens on Tegra devices which use BPMP
co-processor to manage the clocks. Calls to BPMP are always blocking and
hence it is necessary to enable/disable clocks during prepare/unprepare
phase respectively. When pm-clk is used, prepare count of clock is not
balanced until pm_clk_remove() happens. Clock is prepared in the driver
probe() and thus prepare count of clock remains non-zero, which in turn
keeps clock ON always.

Please note that above mentioned behavior is specific to Tegra devices
using BPMP for clock management and this should not be seen on other
devices. Though this patch uses clk_bulk APIs to address the mentioned
behavior, this works fine for all devices.

To simplify gic_get_clocks() API is removed and instead probe can do
necessary setup.
Suggested-by: Mohan Kumar D <mkumard@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

The word 'number' has been misspelt in the comment on top of
_irq_domain_alloc_irqs().
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

The word 'entirely' has been misspelt in a comment in its_msi_prepare().
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Some definitions of Inner Cacheability attibutes need to be corrected.

Fixes: 8c828a53 ("irqchip/gicv3-its: Restore all cacheability attributes")
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

It is useful to print which interrupt controllers are registered in the
system and which parent IRQ they use, especially given that L2 interrupt
controllers do not call request_irq() on their parent interrupt and do
not appear under /proc/interrupts for that reason.

We used to print the base register address virtual address which had
little value, use %pOF to print the path to the Device Tree node which
maps to the physical address more easily and is what people need to
troubleshoot systems.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Merge page ref overflow branch.

Jann Horn reported that he can overflow the page ref count with
sufficient memory (and a filesystem that is intentionally extremely
slow).

Admittedly it's not exactly easy.  To have more than four billion
references to a page requires a minimum of 32GB of kernel memory just
for the pointers to the pages, much less any metadata to keep track of
those pointers.  Jann needed a total of 140GB of memory and a specially
crafted filesystem that leaves all reads pending (in order to not ever
free the page references and just keep adding more).

Still, we have a fairly straightforward way to limit the two obvious
user-controllable sources of page references: direct-IO like page
references gotten through get_user_pages(), and the splice pipe page
duplication.  So let's just do that.

* branch page-refs:
  fs: prevent page refcount overflow in pipe_buf_get
  mm: prevent get_user_pages() from overflowing page refcount
  mm: add 'try_get_page()' helper function
  mm: make page ref count overflow check tighter and more explicit

Change pipe_buf_get() to return a bool indicating whether it succeeded
in raising the refcount of the page (if the thing in the pipe is a page).
This removes another mechanism for overflowing the page refcount.  All
callers converted to handle a failure.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If the page refcount wraps around past zero, it will be freed while
there are still four billion references to it.  One of the possible
avenues for an attacker to try to make this happen is by doing direct IO
on a page multiple times.  This patch makes get_user_pages() refuse to
take a new page reference if there are already more than two billion
references to the page.
Reported-by: Jann Horn <jannh@google.com>
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is the same as the traditional 'get_page()' function, but instead
of unconditionally incrementing the reference count of the page, it only
does so if the count was "safe".  It returns whether the reference count
was incremented (and is marked __must_check, since the caller obviously
has to be aware of it).

Also like 'get_page()', you can't use this function unless you already
had a reference to the page.  The intent is that you can use this
exactly like get_page(), but in situations where you want to limit the
maximum reference count.

The code currently does an unconditional WARN_ON_ONCE() if we ever hit
the reference count issues (either zero or negative), as a notification
that the conditional non-increment actually happened.

NOTE! The count access for the "safety" check is inherently racy, but
that doesn't matter since the buffer we use is basically half the range
of the reference count (ie we look at the sign of the count).
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We have a VM_BUG_ON() to check that the page reference count doesn't
underflow (or get close to overflow) by checking the sign of the count.

That's all fine, but we actually want to allow people to use a "get page
ref unless it's already very high" helper function, and we want that one
to use the sign of the page ref (without triggering this VM_BUG_ON).

Change the VM_BUG_ON to only check for small underflows (or _very_ close
to overflowing), and ignore overflows which have strayed into negative
territory.
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull block fixes from Jens Axboe:
 "Set of fixes that should go into this round. This pull is larger than
  I'd like at this time, but there's really no specific reason for that.
  Some are fixes for issues that went into this merge window, others are
  not. Anyway, this contains:

   - Hardware queue limiting for virtio-blk/scsi (Dongli)

   - Multi-page bvec fixes for lightnvm pblk

   - Multi-bio dio error fix (Jason)

   - Remove the cache hint from the io_uring tool side, since we didn't
     move forward with that (me)

   - Make io_uring SETUP_SQPOLL root restricted (me)

   - Fix leak of page in error handling for pc requests (Jérôme)

   - Fix BFQ regression introduced in this merge window (Paolo)

   - Fix break logic for bio segment iteration (Ming)

   - Fix NVMe cancel request error handling (Ming)

   - NVMe pull request with two fixes (Christoph):
       - fix the initial CSN for nvme-fc (James)
       - handle log page offsets properly in the target (Keith)"

* tag 'for-linus-20190412' of git://git.kernel.dk/linux-block:
  block: fix the return errno for direct IO
  nvmet: fix discover log page when offsets are used
  nvme-fc: correct csn initialization and increments on error
  block: do not leak memory in bio_copy_user_iov()
  lightnvm: pblk: fix crash in pblk_end_partial_read due to multipage bvecs
  nvme: cancel request synchronously
  blk-mq: introduce blk_mq_complete_request_sync()
  scsi: virtio_scsi: limit number of hw queues by nr_cpu_ids
  virtio-blk: limit number of hw queues by nr_cpu_ids
  block, bfq: fix use after free in bfq_bfqq_expire
  io_uring: restrict IORING_SETUP_SQPOLL to root
  tools/io_uring: remove IOCQE_FLAG_CACHEHIT
  block: don't use for-inside-for in bio_for_each_segment_all

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Stable fix:

   - Fix a deadlock in close() due to incorrect draining of RDMA queues

  Bugfixes:

   - Revert "SUNRPC: Micro-optimise when the task is known not to be
     sleeping" as it is causing stack overflows

   - Fix a regression where NFSv4 getacl and fs_locations stopped
     working

   - Forbid setting AF_INET6 to "struct sockaddr_in"->sin_family.

   - Fix xfstests failures due to incorrect copy_file_range() return
     values"

* tag 'nfs-for-5.1-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  Revert "SUNRPC: Micro-optimise when the task is known not to be sleeping"
  NFSv4.1 fix incorrect return value in copy_file_range
  xprtrdma: Fix helper that drains the transport
  NFS: Fix handling of reply page vector
  NFS: Forbid setting AF_INET6 to "struct sockaddr_in"->sin_family.

Pull SCSI fix from James Bottomley:
 "One obvious fix for a ciostor data corruption on error bug"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: csiostor: fix missing data copy in csio_scsi_err_handler()

Pull clk fixes from Stephen Boyd:
 "Here's more than a handful of clk driver fixes for changes that came
  in during the merge window:

   - Fix the AT91 sama5d2 programmable clk prescaler formula

   - A bunch of Amlogic meson clk driver fixes for the VPU clks

   - A DMI quirk for Intel's Bay Trail SoC's driver to properly mark pmc
     clks as critical only when really needed

   - Stop overwriting CLK_SET_RATE_PARENT flag in mediatek's clk gate
     implementation

   - Use the right structure to test for a frequency table in i.MX's
     PLL_1416x driver"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: imx: Fix PLL_1416X not rounding rates
  clk: mediatek: fix clk-gate flag setting
  platform/x86: pmc_atom: Drop __initconst on dmi table
  clk: x86: Add system specific quirk to mark clocks as critical
  clk: meson: vid-pll-div: remove warning and return 0 on invalid config
  clk: meson: pll: fix rounding and setting a rate that matches precisely
  clk: meson-g12a: fix VPU clock parents
  clk: meson: g12a: fix VPU clock muxes mask
  clk: meson-gxbb: round the vdec dividers to closest
  clk: at91: fix programmable clock for sama5d2

Pull PCI fixes from Bjorn Helgaas:

 - Add a DMA alias quirk for another Marvell SATA device (Andre
   Przywara)

 - Fix a pciehp regression that broke safe removal of devices (Sergey
   Miroshnichenko)

* tag 'pci-v5.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: pciehp: Ignore Link State Changes after powering off a slot
  PCI: Add function 1 DMA alias quirk for Marvell 9170 SATA controller

Pull powerpc fixes from Michael Ellerman:
 "A minor build fix for 64-bit FLATMEM configs.

  A fix for a boot failure on 32-bit powermacs.

  My commit to fix CLOCK_MONOTONIC across Y2038 broke the 32-bit VDSO on
  64-bit kernels, ie. compat mode, which is only used on big endian.

  The rewrite of the SLB code we merged in 4.20 missed the fact that the
  0x380 exception is also used with the Radix MMU to report out of range
  accesses. This could lead to an oops if userspace tried to read from
  addresses outside the user or kernel range.

  Thanks to: Aneesh Kumar K.V, Christophe Leroy, Larry Finger, Nicholas
  Piggin"

* tag 'powerpc-5.1-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/mm: Define MAX_PHYSMEM_BITS for all 64-bit configs
  powerpc/64s/radix: Fix radix segment exception handling
  powerpc/vdso32: fix CLOCK_MONOTONIC on PPC64
  powerpc/32: Fix early boot failure with RTAS built-in

Pull arm64 fixes from Will Deacon:
 "The main thing is a fix to our FUTEX_WAKE_OP implementation which was
  unbelievably broken, but did actually work for the one scenario that
  GLIBC used to use.

  Summary:

   - Fix stack unwinding so we ignore user stacks

   - Fix ftrace module PLT trampoline initialisation checks

   - Fix terminally broken implementation of FUTEX_WAKE_OP atomics"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: futex: Fix FUTEX_WAKE_OP atomic ops with non-zero result value
  arm64: backtrace: Don't bother trying to unwind the userspace stack
  arm64/ftrace: fix inadvertent BUG() in trampoline check

Pull x86 fixes from Ingo Molnar:
 "Fix typos in user-visible resctrl parameters, and also fix assembly
  constraint bugs that might result in miscompilation"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm: Use stricter assembly constraints in bitops
  x86/resctrl: Fix typos in the mba_sc mount option

Pull timer fix from Ingo Molnar:
 "Fix the alarm_timer_remaining() return value"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  alarmtimer: Return correct remaining time