- 13 Apr, 2012 38 commits
-
-
Kuninori Morimoto authored
commit 1f99e44c upstream. ak4642 out_tlv is +12.0dB to -115.0 dB, and it supports mute. But current settings didn't care +1 step for mute. This patch adds it Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Guan Xin authored
commit a2daf263 upstream. Added Vendor/Device Id of Motorola Rokr E6 (22b8:6027) so it can be recognized by the "zaurus" USBNet driver. Applies to Linux 3.2.13 and 2.6.39.4. Signed-off-by:
Guan Xin <guanx.bac@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Nishanth Menon authored
commit 3f8349e6 upstream. TWL6030 family of PMIC use a shadow interrupt status register while kernel processes the current interrupt event. However, any write(0 or 1) to register INT_STS_A, INT_STS_B or INT_STS_C clears all 3 interrupt status registers. Since clear of the interrupt is done on 32k clk, depending on I2C bus speed, we could in-adverently clear the status of a interrupt status pending on shadow register in the current implementation. This is due to the fact that multi-byte i2c write operation into three seperate status register could result in multiple load and clear of status and result in lost interrupts. Instead, doing a single byte write to INT_STS_A register with 0x0 will clear all three interrupt status registers without the related risk. Acked-by:
Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
-
Salman Qazi authored
commit 9993bc63 upstream. When a machine boots up, the TSC generally gets reset. However, when kexec is used to boot into a kernel, the TSC value would be carried over from the previous kernel. The computation of cycns_offset in set_cyc2ns_scale is prone to an overflow, if the machine has been up more than 208 days prior to the kexec. The overflow happens when we multiply *scale, even though there is enough room to store the final answer. We fix this issue by decomposing tsc_now into the quotient and remainder of division by CYC2NS_SCALE_FACTOR and then performing the multiplication separately on the two components. Refactor code to share the calculation with the previous fix in __cycles_2_ns(). Signed-off-by:
Salman Qazi <sqazi@google.com> Acked-by:
John Stultz <john.stultz@linaro.org> Acked-by:
Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Turner <pjt@google.com> Cc: john stultz <johnstul@us.ibm.com> Link: http://lkml.kernel.org/r/20120310004027.19291.88460.stgit@dungbeetle.mtv.corp.google.comSigned-off-by:
Ingo Molnar <mingo@elte.hu> Cc: Mike Galbraith <efault@gmx.de> Signed-off-by:
-
Lee, Chun-Yi authored
commit 5719b819 upstream. The wireless rfkill should charged by sony-laptop but not acer-wmi. So, add Sony's SNY5001 acpi device to blacklist in acer-wmi. Tested on Sony Vaio Cc: Carlos Corbacho <carlos@strangeworlds.co.uk> Cc: Matthew Garrett <mjg@redhat.com> Cc: Mattia Dongili <malattia@linux.it> Cc: Dimitris N <ddarlac@gmail.com> Tested-by:
Dimitris N <ddarlac@gmail.com> Signed-off-by:
Lee, Chun-Yi <jlee@suse.com> Signed-off-by:
Matthew Garrett <mjg@redhat.com> Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit c2ec63ed [73d63d03 upstream] It causes problems, so needs to be reverted from 3.2-stable for now. Reported-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Jon Dufresne <jon@jondufresne.org> Cc: Suresh Siddha <suresh.b.siddha@intel.com> Cc: <yinghai@kernel.org> Cc: Josh Boyer <jwboyer@redhat.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Teck Choon Giam <giamteckchoon@gmail.com> Cc: Ben Guthro <ben@guthro.net> Signed-off-by:
-
Jonathan Nieder authored
commit a97f4f5e upstream. Carlos was getting WARNING: at drivers/pci/pci.c:118 pci_ioremap_bar+0x24/0x52() when probing his sound card, and sound did not work. After adding pci=use_crs to the kernel command line, no more trouble. Ok, we can add a quirk. dmidecode output reveals that this is an MSI MS-7253, for which we already have a quirk, but the short-sighted author tied the quirk to a single BIOS version, making it not kick in on Carlos's machine with BIOS V1.2. If a later BIOS update makes it no longer necessary to look at the _CRS info it will still be harmless, so let's stop trying to guess which versions have and don't have accurate _CRS tables. Addresses https://bugtrack.alsa-project.org/alsa-bug/view.php?id=5533 Also see <https://bugzilla.kernel.org/show_bug.cgi?id=42619>. Reported-by:
Carlos Luna <caralu74@gmail.com> Reviewed-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
Jonathan Nieder <jrnieder@gmail.com> Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
-
Jonathan Nieder authored
commit 84113717 upstream. In the spirit of commit 29cf7a30 ("x86/PCI: use host bridge _CRS info on ASUS M2V-MX SE"), this DMI quirk turns on "pci_use_crs" by default on a board that needs it. This fixes boot failures and oopses introduced in 3e3da00c ("x86/pci: AMD one chain system to use pci read out res"). The quirk is quite targetted (to a specific board and BIOS version) for two reasons: (1) to emphasize that this method of tackling the problem one quirk at a time is a little insane (2) to give BIOS vendors an opportunity to use simpler tables and allow us to return to generic behavior (whatever that happens to be) with a later BIOS update In other words, I am not at all happy with having quirks like this. But it is even worse for the kernel not to work out of the box on these machines, so... Reference: https://bugzilla.kernel.org/show_bug.cgi?id=42619Reported-by:
Svante Signell <svante.signell@telia.com> Signed-off-by:
-
Frank Rowand authored
commit 258f7426 upstream. Commit f02e8a65 ("module: Sort exported symbols") sorts symbols placing each of them in its own elf section. This sorting and merging into the canonical sections are done by the linker. Unfortunately modpost to generate Module.symvers file parses vmlinux.o (which is not linked yet) and all modules object files (which aren't linked yet). These aren't sanitized by the linker yet. That breaks modpost that can't detect license properly for modules. This patch makes modpost aware of the new exported symbols structure. [ This above is a slightly corrected version of the explanation of the problem, copied from commit 62a26356 ("modpost: Fix modpost's license checking V3"). That commit fixed the problem for module object files, but not for vmlinux.o. This patch fixes modpost for vmlinux.o. ] Signed-off-by:
Frank Rowand <frank.rowand@am.sony.com> Signed-off-by:
Alessio Igor Bogani <abogani@kernel.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Alessio Igor Bogani authored
commit 62a26356 upstream. The commit f02e8a65 sorts symbols placing each of them in its own elf section. The sorting and merging into the canonical sections are done by the linker. Unfortunately modpost to generate Module.symvers file parses vmlinux (already linked) and all modules object files (which aren't linked yet). These aren't sanitized by the linker yet. That breaks modpost that can't detect license properly for modules. This patch makes modpost aware of the new exported symbols structure. Thanks to Arnaud Lacombe <lacombar@gmail.com> and Anders Kaseorg <andersk@ksplice.com> for providing useful suggestions about code. This work was supported by a hardware donation from the CE Linux Forum. Reported-by:
Jan Beulich <jbeulich@novell.com> Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
-
Kees Cook authored
commit 620f6e8e upstream. Commit bfdc0b49 adds code to restrict access to dmesg_restrict, however, it incorrectly alters kptr_restrict rather than dmesg_restrict. The original patch from Richard Weinberger (https://lkml.org/lkml/2011/3/14/362) alters dmesg_restrict as expected, and so the patch seems to have been misapplied. This adds the CAP_SYS_ADMIN check to both dmesg_restrict and kptr_restrict, since both are sensitive. Reported-by:
Phillip Lougher <plougher@redhat.com> Signed-off-by:
Kees Cook <keescook@chromium.org> Acked-by:
Serge Hallyn <serge.hallyn@canonical.com> Acked-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
James Morris <james.l.morris@oracle.com> Signed-off-by:
-
Ludovic Desroches authored
commit 66292ad9 upstream. The HSMCI operates at a rate of up to Master Clock divided by two. Moreover previous calculation can cause overflows and so wrong timeouts. Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
Chris Ball <cjb@laptop.org> Signed-off-by:
-
Jason Wessel authored
commit 3751d3e8 upstream. There has long been a limitation using software breakpoints with a kernel compiled with CONFIG_DEBUG_RODATA going back to 2.6.26. For this particular patch, it will apply cleanly and has been tested all the way back to 2.6.36. The kprobes code uses the text_poke() function which accommodates writing a breakpoint into a read-only page. The x86 kgdb code can solve the problem similarly by overriding the default breakpoint set/remove routines and using text_poke() directly. The x86 kgdb code will first attempt to use the traditional probe_kernel_write(), and next try using a the text_poke() function. The break point install method is tracked such that the correct break point removal routine will get called later on. Cc: x86@kernel.org Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Inspried-by:
Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by:
Jason Wessel <jason.wessel@windriver.com> Signed-off-by:
-
Jason Wessel authored
commit 23bbd8e3 upstream. The do_fork and sys_open tests have never worked properly on anything other than a UP configuration with the kgdb test suite. This is because the test suite did not fully implement the behavior of a real debugger. A real debugger tracks the state of what thread it asked to single step and can correctly continue other threads of execution or conditionally stop while waiting for the original thread single step request to return. Below is a simple method to cause a fatal kernel oops with the kgdb test suite on a 2 processor ARM system: while [ 1 ] ; do ls > /dev/null 2> /dev/null; done& while [ 1 ] ; do ls > /dev/null 2> /dev/null; done& echo V1I1F100 > /sys/module/kgdbts/parameters/kgdbts Very soon after starting the test the kernel will start warning with messages like: kgdbts: BP mismatch c002487c expected c0024878 ------------[ cut here ]------------ WARNING: at drivers/misc/kgdbts.c:317 check_and_rewind_pc+0x9c/0xc4() [<c01f6520>] (check_and_rewind_pc+0x9c/0xc4) [<c01f595c>] (validate_simple_test+0x3c/0xc4) [<c01f60d4>] (run_simple_test+0x1e8/0x274) The kernel will eventually recovers, but the test suite has completely failed to test anything useful. This patch implements behavior similar to a real debugger that does not rely on hardware single stepping by using only software planted breakpoints. In order to mimic a real debugger, the kgdb test suite now tracks the most recent thread that was continued (cont_thread_id), with the intent to single step just this thread. When the response to the single step request stops in a different thread that hit the original break point that thread will now get continued, while the debugger waits for the thread with the single step pending. Here is a high level description of the sequence of events. cont_instead_of_sstep = 0; 1) set breakpoint at do_fork 2) continue 3) Save the thread id where we stop to cont_thread_id 4) Remove breakpoint at do_fork 5) Reset the PC if needed depending on kernel exception type 6) soft single step 7) Check where we stopped if current thread != cont_thread_id { if (here for more than 2 times for the same thead) { ### must be a really busy system, start test again ### goto step 1 } goto step 5 } else { cont_instead_of_sstep = 0; } 8) clean up and run test again if needed 9) Clear out any threads that were waiting on a break point at the point in time the test is ended with get_cont_catch(). This happens sometimes because breakpoints are used in place of single stepping and some threads could have been in the debugger exception handling queue because breakpoints were hit concurrently on different CPUs. This also means we wait at least one second before unplumbing the debugger connection at the very end, so as respond to any debug threads waiting to be serviced. Signed-off-by:
-
Jason Wessel authored
commit 486c5987 upstream. The do_fork and sys_open tests have never worked properly on anything other than a UP configuration with the kgdb test suite. This is because the test suite did not fully implement the behavior of a real debugger. A real debugger tracks the state of what thread it asked to single step and can correctly continue other threads of execution or conditionally stop while waiting for the original thread single step request to return. Below is a simple method to cause a fatal kernel oops with the kgdb test suite on a 4 processor x86 system: while [ 1 ] ; do ls > /dev/null 2> /dev/null; done& while [ 1 ] ; do ls > /dev/null 2> /dev/null; done& while [ 1 ] ; do ls > /dev/null 2> /dev/null; done& while [ 1 ] ; do ls > /dev/null 2> /dev/null; done& echo V1I1F1000 > /sys/module/kgdbts/parameters/kgdbts Very soon after starting the test the kernel will oops with a message like: kgdbts: BP mismatch 3b7da66480 expected ffffffff8106a590 WARNING: at drivers/misc/kgdbts.c:303 check_and_rewind_pc+0xe0/0x100() Call Trace: [<ffffffff812994a0>] check_and_rewind_pc+0xe0/0x100 [<ffffffff81298945>] validate_simple_test+0x25/0xc0 [<ffffffff81298f77>] run_simple_test+0x107/0x2c0 [<ffffffff81298a18>] kgdbts_put_char+0x18/0x20 The warn will turn to a hard kernel crash shortly after that because the pc will not get properly rewound to the right value after hitting a breakpoint leading to a hard lockup. This change is broken up into 2 pieces because archs that have hw single stepping (2.6.26 and up) need different changes than archs that do not have hw single stepping (3.0 and up). This change implements the correct behavior for an arch that supports hw single stepping. A minor defect was fixed where sys_open should be do_sys_open for the sys_open break point test. This solves the problem of running a 64 bit with a 32 bit user space. The sys_open() never gets called when using the 32 bit file system for the kgdb testsuite because the 32 bit binaries invoke the compat_sys_open() call leading to the test never completing. In order to mimic a real debugger, the kgdb test suite now tracks the most recent thread that was continued (cont_thread_id), with the intent to single step just this thread. When the response to the single step request stops in a different thread that hit the original break point that thread will now get continued, while the debugger waits for the thread with the single step pending. Here is a high level description of the sequence of events. cont_instead_of_sstep = 0; 1) set breakpoint at do_fork 2) continue 3) Save the thread id where we stop to cont_thread_id 4) Remove breakpoint at do_fork 5) Reset the PC if needed depending on kernel exception type 6) if (cont_instead_of_sstep) { continue } else { single step } 7) Check where we stopped if current thread != cont_thread_id { cont_instead_of_sstep = 1; goto step 5 } else { cont_instead_of_sstep = 0; } 8) clean up and run test again if needed Signed-off-by:
-
Jason Wessel authored
commit 456ca7ff upstream. On x86 the kgdb test suite will oops when the kernel is compiled with CONFIG_DEBUG_RODATA and you run the tests after boot time. This is regression has existed since 2.6.26 by commit: b33cb815 (kgdbts: Use HW breakpoints with CONFIG_DEBUG_RODATA). The test suite can use hw breakpoints for all the tests, but it has to execute the hardware breakpoint specific tests first in order to determine that the hw breakpoints actually work. Specifically the very first test causes an oops: # echo V1I1 > /sys/module/kgdbts/parameters/kgdbts kgdb: Registered I/O driver kgdbts. kgdbts:RUN plant and detach test Entering kdb (current=0xffff880017aa9320, pid 1078) on processor 0 due to Keyboard Entry [0]kdb> kgdbts: ERROR PUT: end of test buffer on 'plant_and_detach_test' line 1 expected OK got $E14#aa WARNING: at drivers/misc/kgdbts.c:730 run_simple_test+0x151/0x2c0() [...oops clipped...] This commit re-orders the running of the tests and puts the RODATA check into its own function so as to correctly avoid the kernel oops by detecting and using the hw breakpoints. Signed-off-by:
-
Jason Wessel authored
commit 98b54aa1 upstream. There is extra state information that needs to be exposed in the kgdb_bpt structure for tracking how a breakpoint was installed. The debug_core only uses the the probe_kernel_write() to install breakpoints, but this is not enough for all the archs. Some arch such as x86 need to use text_poke() in order to install a breakpoint into a read only page. Passing the kgdb_bpt structure to kgdb_arch_set_breakpoint() and kgdb_arch_remove_breakpoint() allows other archs to set the type variable which indicates how the breakpoint was installed. Signed-off-by:
-
Daniel Vetter authored
commit 25e341cf upstream. Somehow the BIOS manages to screw things up when copying the VBT around, because the one we scrap from the VBIOS rom actually works. Tested-by:
Markus Heinz <markus.heinz@uni-dortmund.de> Acked-by:
Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
Rodrigo Vivi <rodrigo.vivi@gmail.com> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28812Signed-Off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Sean Paul authored
commit 927a2f11 upstream. i915_drm_thaw was not locking the mode_config lock when calling drm_helper_resume_force_mode. When there were multiple wake sources, this caused FDI training failure on SNB which in turn corrupted the display. Signed-off-by:
Sean Paul <seanpaul@chromium.org> Reviewed-by:
-
Chris Wilson authored
commit f47166d2 upstream. Quoting the BSpec from time immemorial: PIPEACONF, bits 28:27: Frame Start Delay (Debug) Used to delay the frame start signal that is sent to the display planes. Care must be taken to insure that there are enough lines during VBLANK to support this setting. An instance of the BIOS leaving these bits set was found in the wild, where it caused our modesetting to go all squiffy and skewiff. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47271Reported-and-tested-by:
Eva Wang <evawang@linpus.com> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43012Reported-and-tested-by:
Carl Richell <carl@system76.com> Signed-off-by:
-
Anisse Astier authored
commit 97effadb upstream. This hardware doesn't have an LVDS, it's a desktop box. Fix incorrect LVDS detection. Signed-off-by:
Anisse Astier <anisse@astier.eu> Acked-by:
-
Alex Deucher authored
commit 402976fe upstream. On pre-R600 asics, the SpeedFanControl table is not executed as part of ASIC_Init as it is on newer asics. Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=29412Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Reviewed-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Chris Wilson authored
commit 62fb376e upstream. mplayer -vo fbdev tries to create a screen that is twice as tall as the allocated framebuffer for "doublebuffering". By default, and all in-tree users, only sufficient memory is allocated and mapped to satisfy the smallest framebuffer and the virtual size is no larger than the actual. For these users, we should therefore reject any userspace request to create a screen that requires a buffer larger than the framebuffer originally allocated. References: https://bugs.freedesktop.org/show_bug.cgi?id=38138Signed-off-by:
-
Stanislaw Gruszka authored
commit d72308bf upstream. Is possible that we will arm the tid_rx->reorder_timer after del_timer_sync() in ___ieee80211_stop_rx_ba_session(). We need to stop timer after RCU grace period finish, so move it to ieee80211_free_tid_rx(). Timer will not be armed again, as rcu_dereference(sta->ampdu_mlme.tid_rx[tid]) will return NULL. Debug object detected problem with the following warning: ODEBUG: free active (active state 0) object type: timer_list hint: sta_rx_agg_reorder_timer_expired+0x0/0xf0 [mac80211] Bug report (with all warning messages): https://bugzilla.redhat.com/show_bug.cgi?id=804007Reported-by:
"jan p. springer" <jsd@igroup.org> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Geert Uytterhoeven authored
commit 6cfeba53 upstream. On multi-platform kernels, the Mac platform devices should be registered when running on Mac only. Else it may crash later. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Wolfgang Mauerer authored
commit 01de982a upstream. 8 hex characters tell only half the tale for 64 bit CPUs, so use the appropriate length. Link: http://lkml.kernel.org/r/1332411501-8059-2-git-send-email-wolfgang.mauerer@siemens.comSigned-off-by:
Wolfgang Mauerer <wolfgang.mauerer@siemens.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Jiang Liu authored
commit f5cb92ac upstream. irq_move_masked_irq() checks the return code of chip->irq_set_affinity() only for 0, but IRQ_SET_MASK_OK_NOCOPY is also a valid return code, which is there to avoid a redundant copy of the cpumask. But in case of IRQ_SET_MASK_OK_NOCOPY we not only avoid the redundant copy, we also fail to adjust the thread affinity of an eventually threaded interrupt handler. Handle IRQ_SET_MASK_OK (==0) and IRQ_SET_MASK_OK_NOCOPY(==1) return values correctly by checking the valid return values seperately. Signed-off-by:
Jiang Liu <jiang.liu@huawei.com> Cc: Jiang Liu <liuj97@gmail.com> Cc: Keping Chen <chenkeping@huawei.com> Link: http://lkml.kernel.org/r/1333120296-13563-2-git-send-email-jiang.liu@huawei.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Jan Beulich authored
commit 9aaf440f upstream. This was lacking a comma between two supposed to be separate strings. Signed-off-by:
Jan Beulich <jbeulich@suse.com> Signed-off-by:
Michal Marek <mmarek@suse.cz> Signed-off-by:
-
Julian Anastasov authored
commit 3e80acd1 upstream. commit 64b3db22 (2.6.39), "Remove use of unreliable FADT revision field" causes regression for old P4 systems because now cst_control and other fields are not reset to 0. The effect is that acpi_processor_power_init will notice cst_control != 0 and a write to CST_CNT register is performed that should not happen. As result, the system oopses after the "No _CST, giving up" message, sometimes in acpi_ns_internalize_name, sometimes in acpi_ns_get_type, usually at random places. May be during migration to CPU 1 in acpi_processor_get_throttling. Every one of these settings help to avoid this problem: - acpi=off - processor.nocst=1 - maxcpus=1 The fix is to update acpi_gbl_FADT.header.length after the original value is used to check for old revisions. https://bugzilla.kernel.org/show_bug.cgi?id=42700 https://bugzilla.redhat.com/show_bug.cgi?id=727865Signed-off-by:
Julian Anastasov <ja@ssi.bg> Acked-by:
Bob Moore <robert.moore@intel.com> Signed-off-by:
Len Brown <len.brown@intel.com> Cc: Jonathan Nieder <jrnieder@gmail.com> Cc: Josh Boyer <jwboyer@gmail.com> Signed-off-by:
-
Yinghai Lu authored
commit 89e96ada upstream. During testing pci root bus removal, found some root bus bridge is not freed. If booting with pnpacpi=off, those hostbridge could be freed without problem. It turns out that some devices reference are not released during acpi_pnp_match. that match should not hold one device ref during every calling. Add pu_device calling before returning. Signed-off-by:
Yinghai Lu <yinghai@kernel.org> Signed-off-by:
-
Andi Kleen authored
commit 2815ab92 upstream. On Intel CPUs the processor typically uses the highest frequency set by any logical CPU. When the system overheats Linux first forces the frequency to the lowest available one to lower the temperature. However this was done only per logical CPU, which means all logical CPUs in a package would need to go through this before the frequency is actually lowered. Worse this delay actually prevents real throttling, because the real throttle code only proceeds when the lowest frequency is already reached. So when a throttle event happens force the lowest frequency for all CPUs in the package where it happened. The per CPU state is now kept per package, not per logical CPU. An alternative would be to do it per cpufreq unit, but since we want to bring down the temperature of the complete chip it's better to do it for all. In principle it may even make sense to do it for all CPUs, but I kept it on the package for now. With this change the frequency is actually lowered, which in terms also allows real throttling to proceed. I also removed an unnecessary per cpu variable initialization. v2: Fix package mapping Signed-off-by:
Andi Kleen <ak@linux.intel.com> Signed-off-by:
-
Brian Norris authored
commit b54f47c8 upstream. Using UBI on m25p80 can give messages like: UBI error: io_init: bad write buffer size 0 for 1 min. I/O unit We need to initialize writebufsize; I think "page_size" is the correct "bufsize", although I'm not sure. Comments? Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
Artem Bityutskiy authored
commit fcc44a07 upstream. The writebufsize concept was introduce by commit "0e4ca7e5 mtd: add writebufsize field to mtd_info struct" and it represents the maximum amount of data the device writes to the media at a time. This is an important parameter for UBIFS which is used during recovery and which basically defines how big a corruption caused by a power cut can be. Set writebufsize to 4 because this drivers writes at max 4 bytes at a time. Signed-off-by:
-
Artem Bityutskiy authored
commit b6043874 upstream. The writebufsize concept was introduce by commit "0e4ca7e5 mtd: add writebufsize field to mtd_info struct" and it represents the maximum amount of data the device writes to the media at a time. This is an important parameter for UBIFS which is used during recovery and which basically defines how big a corruption caused by a power cut can be. However, we forgot to set this parameter for block2mtd. Set it to PAGE_SIZE because this is actually the amount of data we write at a time. Signed-off-by:
Joern Engel <joern@lazybastard.org> Signed-off-by:
-
Artem Bityutskiy authored
commit c4cc625e upstream. The writebufsize concept was introduce by commit "0e4ca7e5 mtd: add writebufsize field to mtd_info struct" and it represents the maximum amount of data the device writes to the media at a time. This is an important parameter for UBIFS which is used during recovery and which basically defines how big a corruption caused by a power cut can be. Set writebufsize to the flash page size because it is the maximum amount of data it writes at a time. Signed-off-by:
-
Rabin Vincent authored
[ Upstream commit 78fb72f7 ] Make CDC EEM recalculate the hard_mtu after adjusting the hard_header_len. Without this, usbnet adjusts the MTU down to 1494 bytes, and the host is unable to receive standard 1500-byte frames from the device. Tested with the Linux USB Ethernet gadget. Cc: Oliver Neukum <oliver@neukum.name> Signed-off-by:
Rabin Vincent <rabin@rab.in> Signed-off-by:
-
danborkmann@iogearbox.net authored
[ Upstream commit 81213b5e ] If both addresses equal, nothing needs to be done. If the device is down, then we simply copy the new address to dev->dev_addr. If the device is up, then we add another loopback device with the new address, and if that does not fail, we remove the loopback device with the old address. And only then, we update the dev->dev_addr. Signed-off-by:
Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch> Signed-off-by:
-
zhuangfeiran@ict.ac.cn authored
[ Upstream commit 1d24fb36 ] When K >= 0xFFFF0000, AND needs the two least significant bytes of K as its operand, but EMIT2() gives it the least significant byte of K and 0x2. EMIT() should be used here to replace EMIT2(). Signed-off-by:
Feiran Zhuang <zhuangfeiran@ict.ac.cn> Acked-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
- 02 Apr, 2012 2 commits
-
-
Greg Kroah-Hartman authored
-
Matthew Garrett authored
commit c9651e70 upstream. Since 3.2.12 and 3.3, some systems are failing to boot with a BUG_ON. Some other systems using the pata_jmicron driver fail to boot because no disks are detected. Passing pcie_aspm=force on the kernel command line works around it. The cause: commit 4949be16 ("PCI: ignore pre-1.1 ASPM quirking when ASPM is disabled") changed the behaviour of pcie_aspm_sanity_check() to always return 0 if aspm is disabled, in order to avoid cases where we changed ASPM state on pre-PCIe 1.1 devices. This skipped the secondary function of pcie_aspm_sanity_check which was to avoid us enabling ASPM on devices that had non-PCIe children, causing trouble later on. Move the aspm_disabled check so we continue to honour that scenario. Addresses https://bugzilla.kernel.org/show_bug.cgi?id=42979 and http://bugs.debian.org/665420 Reported-by: Romain Francoise <romain@orebokech.com> # kernel panic Reported-by: Chris Holland <bandidoirlandes@gmail.com> # disk detection trouble Signed-off-by:
-
