We need to reset the chip in teardown path so that it can work
next time when driver is loaded. This patch adds support for
this reset configuration for SDIO.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

card reset is not working with recent kernels. Using
host->card->ocr instead of host->ocr_avail solved the problem.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

EEPROM read frame is sent during device initialization to read mac address.
The format of the frame is modified in firmware to include eeprom length
and offset. This frame does not return firmware version now. Also same
frame is sent again to read rf type and band information.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Whenever new fsm_state enum element is added, fsm_state array
also needs to be updated. If this change is missed, we may end
up doing invalid access in array. BUILD_BUG_ON check will help
to avoid this problem.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath.git patches for 4.14. Major changes:

ath10k

* preparation for wcn3990 support

This fixes the following kernel warning:

  [ 5668.771453] BUG: spinlock bad magic on CPU#0, kworker/u2:3/9745
  [ 5668.771850]  lock: 0xce63ef20, .magic: 00000000, .owner: <none>/-1,
  .owner_cpu: 0
  [ 5668.772277] CPU: 0 PID: 9745 Comm: kworker/u2:3 Tainted: G        W
  4.12.0-03002-gec979a4-dirty #40
  [ 5668.772796] Hardware name: Nokia RX-51 board
  [ 5668.773071] Workqueue: phy1 wl1251_irq_work
  [ 5668.773345] [<c010c9e4>] (unwind_backtrace) from [<c010a274>]
  (show_stack+0x10/0x14)
  [ 5668.773803] [<c010a274>] (show_stack) from [<c01545a4>]
  (do_raw_spin_lock+0x6c/0xa0)
  [ 5668.774230] [<c01545a4>] (do_raw_spin_lock) from [<c06ca578>]
  (_raw_spin_lock_irqsave+0x10/0x18)
  [ 5668.774658] [<c06ca578>] (_raw_spin_lock_irqsave) from [<c048c010>]
  (wl1251_op_tx+0x38/0x5c)
  [ 5668.775115] [<c048c010>] (wl1251_op_tx) from [<c06a12e8>]
  (ieee80211_tx_frags+0x188/0x1c0)
  [ 5668.775543] [<c06a12e8>] (ieee80211_tx_frags) from [<c06a138c>]
  (__ieee80211_tx+0x6c/0x130)
  [ 5668.775970] [<c06a138c>] (__ieee80211_tx) from [<c06a3dbc>]
  (ieee80211_tx+0xdc/0x104)
  [ 5668.776367] [<c06a3dbc>] (ieee80211_tx) from [<c06a4af0>]
  (__ieee80211_subif_start_xmit+0x454/0x8c8)
  [ 5668.776824] [<c06a4af0>] (__ieee80211_subif_start_xmit) from
  [<c06a4f94>] (ieee80211_subif_start_xmit+0x30/0x2fc)
  [ 5668.777343] [<c06a4f94>] (ieee80211_subif_start_xmit) from
  [<c0578848>] (dev_hard_start_xmit+0x80/0x118)
  ...

by adding the missing spin_lock_init().
Reported-by: Pavel Machek <pavel@ucw.cz>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Broadcom BCM53573 SoCs actually have 32 GPIOs, and not 16.

Fixes: 3f37ec79 ("bcma: support BCM53573 series of wireless SoCs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The current code kfree's entry and then dereferences it by accessing
entry->bssid.  Avoid the dereference-after-free by moving the kfree
after the access to entry->bssid.

Detected by CoverityScan, CID#1448600 ("Read from pointer after free")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex records information about various channels as it receives scan
information. It does this by appending to a buffer that was sized
to the max number of supported channels on any band, but there are
numerous problems:

(a) scans can return info from more than one band (e.g., both 2.4 and 5
    GHz), so the determined "max" is not large enough
(b) some firmware appears to return multiple results for a given
    channel, so the max *really* isn't large enough
(c) there is no bounds checking when stashing these stats, so problems
    (a) and (b) can easily lead to buffer overflows

Let's patch this by setting a slightly-more-correct max (that accounts
for a combination of both 2.4G and 5G bands) and adding a bounds check
when writing to our statistics buffer.

Due to problem (b), we still might not properly report all known survey
information (e.g., with "iw <dev> survey dump"), since duplicate results
(or otherwise "larger than expected" results) will cause some
truncation. But that's a problem for a future bugfix.

(And because of this known deficiency, only log the excess at the WARN
level, since that isn't visible by default in this driver and would
otherwise be a bit too noisy.)

Fixes: bf354433 ("mwifiex: channel statistics support for mwifiex")
Cc: <stable@vger.kernel.org>
Cc: Avinash Patil <patila@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Manish Chopra says:

====================
qed/qede: Enhancements

This patch series adds these below features support in qed/qede

1) Ntuple filter configuration [via ethtool -n/N]
2) EEE (energy efficient ethernet) support [ethtool --set-eee/show-eee]
3) Coalescing configuration support for VFs [via ethtool -c/C]

Please consider applying this to "net-next"

V1->V2:
* Fixes below Kbuild test robot warning.

drivers/net//ethernet/qlogic/qed/qed_l2.c:
In function 'qed_get_queue_coalesce':
drivers/net//ethernet/qlogic/qed/qed_l2.c:2137:8: error:
implicit declaration of function 'qed_vf_pf_get_coalesce'
[-Werror=implicit-function-declaration]
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Maximum coalesce per Rx/Tx queue is extended from
255 to 511.
Signed-off-by: Rahul Verma <rahul.verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Retrieve the actual coalesce value from hardware for every Rx/Tx
queue, instead of Rx/Tx coalesce value cached during set coalesce.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add the ethtool support to set RX/Tx coalesce
value to the VF associated Rx/Tx queues.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds ethtool callback implementations for querying/configuring
the Energy Efficient Ethernet (EEE) parameters.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds required driver support for reading/configuring the
Energy Efficient Ethernet (EEE) parameters.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for adding and deleting rx flow
classification rules. Using this user can classify RX flow
constituting of TCP/UDP 4-tuples [src_ip/dst_ip and src_port/dst_port]
to be steered on a given RX queue
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for ethtool getter APIs to query
RX flow classification rules.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2017-07-25

This series contains updates to i40e and i40evf only.

Gustavo Silva fixes a variable assignment, where the incorrect variable
was being used to store the error parameter.

Carolyn provides a fix for a problem found in systems when entering S4
state, by ensuring that the misc vector's IRQ is disabled as well.

Jake removes the single-threaded restriction on the module workqueue,
which was causing issues with events such as CORER.  Does some future
proofing, by changing how the driver displays the UDP tunnel type.

Paul adds a retry in releasing resources if the admin queue times out
during the first attempt to release the resources.

Jesse fixes up references to 32bit timspec, since there are a small set
of errors on 32 bit, so we need to be using the right calls for dealing
with timespec64 variables.  Cleaned up code indentation and corrected
an "if" conditional check, as well as making the code flow more clear.
Cast or changed the types to remove warnings for comparing signed and
unsigned types.  Adds missing includes in i40evf, which were being used
but were not being directly included.

Daniel Borkmann fixes i40e to fill the XDP prog_id with the id just like
other XDP enabled drivers, so that on dump we can retrieve the attached
program based on the id and dump BPF insns, opcodes, etc back to user
space.

Tushar Dave adds le32_to_cpu while evaluating the hardware descriptor
fields, since they are in little-endian format.  Also removed
unnecessary "__packed" to a couple of i40evf structures.

Stefan Assmann fixes an issue when an administratively set MAC was set
and should now be switched back to 00:00:00:00:00:00, the pf_set_mac
flag is not being toggled back to false.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2017-07-25

This series contains updates to ixgbe only.

Tony provides all of the changes in the series, starting with adding a
check to ensure that adding a MAC filter was successful, before setting the
MACVLAN.  In order to receive notifications of link configurations of the
external PHY and support the configuration of the internal iXFI link on
X552 devices, Tony enables LASI interrupts.  Update the iXFI driver code
flow, since the MAC register NW_MNG_IF_SEL fields have been redefined for
X553 devices, so add MAC checks for iXFI flows.  Added additional checks
for flow control autonegotiation, since it is not support for X553 fiber
 and XFI devices.

v2: removed unnecessary parens noticed by David Miller in patch 6 of the
    series.
v3: dropped patch 6 of the original series, while we work out a more
    generic solution for malicious driver detection (MDD) support.
v4: updated patch 1 of the series with the comments from Joe Perches which
    were:
      - switched logic to return on error
      - return 0 on success
      - declare retval as an integer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new target to install the bpf.h header to $(prefix)/include/bpf/
directory.  This is necessary to build standalone applications using
libbpf, without the need to clone the kernel sources and point to them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

gcc warns that the device name might overflow:

drivers/net/hamradio/dmascc.c: In function 'dmascc_init':
drivers/net/hamradio/dmascc.c:584:22: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=]
   sprintf(dev->name, "dmascc%i", 2 * n + i);
drivers/net/hamradio/dmascc.c:584:3: note: 'sprintf' output between 8 and 17 bytes into a destination of size 16
   sprintf(dev->name, "dmascc%i", 2 * n + i);

>From the static data in this file, I can tell that the index is
strictly limited to 16, so it won't overflow. This simply changes
the sprintf() to snprintf(), which is a good idea in general,
and shuts up this warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an administratively set MAC was previously set and should now be
switched back to 00:00:00:00:00:00 the pf_set_mac flag did not get
toggled back to false.
As a result VFs were still treated as if an administratively set MAC was
present.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This is similar to 'commit 9588397d ("i40e: remove unnecessary
__packed")' to avoid unaligned access.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e hardware descriptor fields are in little-endian format. Driver
must use le32_to_cpu while evaluating these fields otherwise on
big-endian arch we end up evaluating incorrect values, cause errors
like:
i40evf 0000:03:0a.0: Expected response 24 from PF, received 402653184
i40evf 0000:03:0a.1: Expected response 7 from PF, received 117440512
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fill the XDP prog_id with the id just like we do in other XDP enabled
drivers such as ixgbe. This is needed so that on dump we can retrieve
the attached program based on the id, and dump BPF insns, opcodes, etc
back to user space. Only XDP driver missing this is currently i40e.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

These includes were all being used in the driver, but weren't
being directly included.

Since the current advised method is to directly include anything
that you need, this implements that.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e driver attempts to display the UDP tunnel name by doing a check
against the type, where for non-zero types we use "vxlan" and for zero
type we use "geneve". This is not future proof, because if new tunnel
types get added, we'll incorrectly label them. It also depends on the
value of UDP_TUNNEL_TYPE_GENEVE == 0, which is brittle.

Instead, replace this with a function that can return a constant string
depending on the type. For now we'll use "unknown" for types we don't
know about, and we can expand this in the future if new types get added.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Compiler reported several places where driver compared
signed and unsigned types.  Cast or change the types to remove
the warnings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This just reorders some local vars and makes the code flow
clearer.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The compiler warned on an oddly indented bit of code, and when
investigating that, noted that the functions themselves had
an odd flow. The if condition was checked, and would exclude
a call to AQ, but then the aq_ret would be checked unconditionally
which just looks really weird, and is likely to cause objections.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

As it turns out there was only a small set of errors
on 32 bit, and we just needed to be using the right calls
for dealing with timespec64 variables.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There are some rare cases where the release resource call will return an
admin Q timeout. In these cases the code needs to try to release the
resource again until it succeeds or it times out.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

During certain events such as a CORER, multiple devices will run a work
task to handle some cleanup. This can cause issues due to
a single-threaded workqueue which can mean that a device doesn't cleanup
in time. Prevent this by removing the single-threaded restriction on the
module workqueue. This avoids the need to add more complex yielding
logic in our service task routine. This is also similar to what other
drivers such as fm10k do.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem found in systems when entering
S4 state.  This patch fixes the problem by ensuring that
the misc vector's IRQ is disabled as well.  Without this
patch a stack trace can be seen upon entering S4 state.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix incorrect variable assignment.
Based on line 1511: aq_ret = I40_ERR_PARAM; the correct variable to be
used in this instance is aq_ret instead of ret. Also, variable ret is
updated at line 1602 just before return, so assigning a value to this
variable in this code block is useless.

Addresses-Coverity-ID: 1397693
Signed-off-by: Gustavo A R Silva <garsilva@embeddedor.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

After removing the reset function, the freeze and restore functions
are now unused when CONFIG_PM_SLEEP is disabled:

drivers/net/virtio_net.c:1881:12: error: 'virtnet_restore_up' defined but not used [-Werror=unused-function]
 static int virtnet_restore_up(struct virtio_device *vdev)
drivers/net/virtio_net.c:1859:13: error: 'virtnet_freeze_down' defined but not used [-Werror=unused-function]
 static void virtnet_freeze_down(struct virtio_device *vdev)

A more robust way to do this is to remove the #ifdef around the callers
and instead mark them as __maybe_unused. The compiler will now just
silently drop the unused code.

Fixes: 4941d472 ("virtio-net: do not reset during XDP set")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flow control autonegotiation is not supported for XFI.  Make sure that
ixgbe_device_supports_autoneg_fc() returns false and
hw->fc.disable_fc_autoneg is set to true to avoid running the fc_autoneg
function for that device.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Flow control autonegotiation is not supported for fiber on X553.  Add
device ID checks in ixgbe_device_supports_autoneg_fc() to return the
appropriate value.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The MAC register NW_MNG_IF_SEL fields have been redefined for
X553. These changes impact the iXFI driver code flow. Since iXFI is
only supported in X552, add MAC checks for iXFI flows.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable LASI interrupts on X552 devices in order to receive notifications of
link configurations of the external PHY and support the configuration of
the internal iXFI link since iXFI does not support auto-negotiation.  This
is not required for X553 devices; add a check to avoid enabling LASI
interrupts for X553 devices.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>