If a qdisc is installed on a bonding device, its possible to get
following lockdep splat under stress :

 =============================================
 [ INFO: possible recursive locking detected ]
 3.6.0+ #211 Not tainted
 ---------------------------------------------
 ping/4876 is trying to acquire lock:
  (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830

 but task is already holding lock:
  (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830

 other info that might help us debug this:
  Possible unsafe locking scenario:

        CPU0
        ----
   lock(dev->qdisc_tx_busylock ?: &qdisc_tx_busylock);
   lock(dev->qdisc_tx_busylock ?: &qdisc_tx_busylock);

  *** DEADLOCK ***

  May be due to missing lock nesting notation

 6 locks held by ping/4876:
  #0:  (sk_lock-AF_INET){+.+.+.}, at: [<ffffffff815e5030>] raw_sendmsg+0x600/0xc30
  #1:  (rcu_read_lock_bh){.+....}, at: [<ffffffff815ba4bd>] ip_finish_output+0x12d/0x870
  #2:  (rcu_read_lock_bh){.+....}, at: [<ffffffff8157a0b0>] dev_queue_xmit+0x0/0x830
  #3:  (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830
  #4:  (&bond->lock){++.?..}, at: [<ffffffffa02128c1>] bond_start_xmit+0x31/0x4b0 [bonding]
  #5:  (rcu_read_lock_bh){.+....}, at: [<ffffffff8157a0b0>] dev_queue_xmit+0x0/0x830

 stack backtrace:
 Pid: 4876, comm: ping Not tainted 3.6.0+ #211
 Call Trace:
  [<ffffffff810a0145>] __lock_acquire+0x715/0x1b80
  [<ffffffff810a256b>] ? mark_held_locks+0x9b/0x100
  [<ffffffff810a1bf2>] lock_acquire+0x92/0x1d0
  [<ffffffff8157a191>] ? dev_queue_xmit+0xe1/0x830
  [<ffffffff81726b7c>] _raw_spin_lock+0x3c/0x50
  [<ffffffff8157a191>] ? dev_queue_xmit+0xe1/0x830
  [<ffffffff8106264d>] ? rcu_read_lock_bh_held+0x5d/0x90
  [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830
  [<ffffffff8157a0b0>] ? netdev_pick_tx+0x570/0x570
  [<ffffffffa0212a6a>] bond_start_xmit+0x1da/0x4b0 [bonding]
  [<ffffffff815796d0>] dev_hard_start_xmit+0x240/0x6b0
  [<ffffffff81597c6e>] sch_direct_xmit+0xfe/0x2a0
  [<ffffffff8157a249>] dev_queue_xmit+0x199/0x830
  [<ffffffff8157a0b0>] ? netdev_pick_tx+0x570/0x570
  [<ffffffff815ba96f>] ip_finish_output+0x5df/0x870
  [<ffffffff815ba4bd>] ? ip_finish_output+0x12d/0x870
  [<ffffffff815bb964>] ip_output+0x54/0xf0
  [<ffffffff815bad48>] ip_local_out+0x28/0x90
  [<ffffffff815bc444>] ip_send_skb+0x14/0x50
  [<ffffffff815bc4b2>] ip_push_pending_frames+0x32/0x40
  [<ffffffff815e536a>] raw_sendmsg+0x93a/0xc30
  [<ffffffff8128d570>] ? selinux_file_send_sigiotask+0x1f0/0x1f0
  [<ffffffff8109ddb4>] ? __lock_is_held+0x54/0x80
  [<ffffffff815f6730>] ? inet_recvmsg+0x220/0x220
  [<ffffffff8109ddb4>] ? __lock_is_held+0x54/0x80
  [<ffffffff815f6855>] inet_sendmsg+0x125/0x240
  [<ffffffff815f6730>] ? inet_recvmsg+0x220/0x220
  [<ffffffff8155cddb>] sock_sendmsg+0xab/0xe0
  [<ffffffff810a1650>] ? lock_release_non_nested+0xa0/0x2e0
  [<ffffffff810a1650>] ? lock_release_non_nested+0xa0/0x2e0
  [<ffffffff8155d18c>] __sys_sendmsg+0x37c/0x390
  [<ffffffff81195b2a>] ? fsnotify+0x2ca/0x7e0
  [<ffffffff811958e8>] ? fsnotify+0x88/0x7e0
  [<ffffffff81361f36>] ? put_ldisc+0x56/0xd0
  [<ffffffff8116f98a>] ? fget_light+0x3da/0x510
  [<ffffffff8155f6c4>] sys_sendmsg+0x44/0x80
  [<ffffffff8172fc22>] system_call_fastpath+0x16/0x1b

Avoid this problem using a distinct lock_class_key for bonding
devices.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suppose we have an SCTP connection with two paths. After connection is
established, path1 is not available, thus this path is marked as inactive. Then
traffic goes through path2, but for some reasons packets are delayed (after
rto.max). Because packets are delayed, the retransmit mechanism will switch
again to path1. At this time, we receive a delayed SACK from path2. When we
update the state of the path in sctp_check_transmitted(), we do not take into
account the source address of the SACK, hence we update the wrong path.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just to avoid confusion when people only reads this prototype.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains fixes/updates to ixgbe only.  There are three
PTP fixes, polling loop fix and the addition of a device id (X540-AT1).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

commit d2d68ba9 (ipv4: Cache input routes in fib_info nexthops.)
introduced a regression for forwarding.

This was hard to reproduce but the symptom was that packets were
delivered to local host instead of being forwarded.

David suggested to add fib_type to fib_info so that we dont
inadvertently share same fib_info for different purposes.

With help from Julian Anastasov who provided very helpful
hints, reproduced here :

<quote>
        Can it be a problem related to fib_info reuse
from different routes. For example, when local IP address
is created for subnet we have:

broadcast 192.168.0.255 dev DEV  proto kernel  scope link  src
192.168.0.1
192.168.0.0/24 dev DEV  proto kernel  scope link  src 192.168.0.1
local 192.168.0.1 dev DEV  proto kernel  scope host  src 192.168.0.1

        The "dev DEV  proto kernel  scope link  src 192.168.0.1" is
a reused fib_info structure where we put cached routes.
The result can be same fib_info for 192.168.0.255 and
192.168.0.0/24. RTN_BROADCAST is cached only for input
routes. Incoming broadcast to 192.168.0.255 can be cached
and can cause problems for traffic forwarded to 192.168.0.0/24.
So, this patch should solve the problem because it
separates the broadcast from unicast traffic.

        And the ip_route_input_slow caching will work for
local and broadcast input routes (above routes 1 and 3) just
because they differ in scope and use different fib_info.

</quote>

Many thanks to Chris Clayton for his patience and help.
Reported-by: Chris Clayton <chris2553@googlemail.com>
Bisected-by: Chris Clayton <chris2553@googlemail.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit d760fc37 caused
1G functions to allocate rx rings which were 1/10 of the
size of 10G functions' rx rings.

However, it also caused 10G functions on 5771x boards to
allocate small rings, which limits their possible (default)
rx throughput. This patch causes all 10G functions to use
rings of intended length by default.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes memory allocation to reduce stack footprint
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds device support for Ethernet Controller X540-AT1.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The loop in ixgbe_reinit_fdir_tables_82599() only polls for up to 100us
resulting in failures to update the FDIR filter table at 1Gbps and 10Gbps
when under load.

The poll times for FDIRCTRL.INIT_DONE are 55us, 550us and 5.5ms for 10Gbps,
1Gbps and 100Mbps respectively.

This patch sets the wait time to be the same as in ixgbe_fdir_enable_82599()
Reported-by: Bhushan <shashi-sm@users.sf.net>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a development issue that occurred due to invalid modes reported
in the ethtool get_ts_info function. The issue is resolved by removing
unsupported modes from the Rx supported list.

CC: stable <stable@vger.kernel.org> [3.5]
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver was enabling PPS interrupt even when user wasn't enabling it via the
ptp core. This patch fixes the PPS so that it is only enabled explicitly, and
moves the interrupt enabling code into the correct location in the driver
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stable <stable@vger.kernel.org> [3.5]
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a bug in the method used for calculating the trigger
alignment for SDP0 when enabling a PPS output on the X540. The alignment math
wasn't properly taking into account the overflow cyclecounter, and was
misaligning the pin triggers so that two X540 devices synced properly had
mis-aligned SDP pins. This patch fixes the math to calculate the correct
seconds alignment for the PPS signal.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ethernet/broadcom/tg3.c:8121:8: warning: symbol 'i' shadows an earlier one
drivers/net/ethernet/broadcom/tg3.c:8003:6: originally declared here
drivers/net/ethernet/broadcom/tg3.c:785:5: warning: symbol 'tg3_ape_scratchpad_read' was not declared. Should it be static?
drivers/net/ethernet/broadcom/tg3.c:7781:19: warning: Using plain integer as NULL pointer
drivers/net/ethernet/broadcom/tg3.c:10231:31: error: bad constant expression
Reported-by: Fengguang Wu <fenguang.wu@intel.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_reset_mac_len() relies on the value of the skb->network_header pointer,
therefore we must wait for such pointer to be recalculated before computing
the new mac_len value.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

DRV_MODULE_VERSION is smaller than the ->version buffer so the memcpy()
copies 1 byte past the end of the string.  It's not super harmful, but
it makes the static checkers complain.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an address is added on loopback (ip -6 a a 2002::1/128 dev lo), a route
to fe80::/64 is added in the main table:
  unreachable fe80::/64 dev lo  proto kernel  metric 256  error -101

This route does not match any prefix (no fe80:: address on lo). In fact,
addrconf_dev_config() will not add link local address because this function
filters interfaces by type. If the link local address is added manually, the
route to the link local prefix will be automatically added by
addrconf_add_linklocal().
Note also, that this route is not deleted when the address is removed.

After looking at the code, it seems that addrconf_add_lroute() is redundant with
addrconf_add_linklocal(), because this function will add the link local route
when the link local address is configured.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

chan->count is used by rx channel. If the desc count is not updated by
the clean up loop in cpdma_chan_stop, the value written to the rxfree
register in cpdma_chan_start will be incorrect.
Signed-off-by: Tao Hou <hotforest@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The config combination:

        CONFIG_PCH_GBE=y
        CONFIG_PCH_PTP=y
        CONFIG_PTP_1588_CLOCK=m

doesn't work, because then you have a built-in kernel
object (the PCH_PTP code) referring to symbols in a
module (PTP_1588_CLOCK).

Fix this like IXGBE, by using "select PTP_1588_CLOCK"
instead of a "depends on".
Reported-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull spi updates from Mark Brown:
 "No framework work here, only a bunch of driver updates of varying
  sizes:

   - Factoring out of the core hardware support from the MXS MMC driver
     by Marek Vasut to allow the hardware to also be used for SPI.
   - Lots of error handling cleanups from Guenter Roeck
   - Removal of the existing Tegra driver which is quite comprehensively
     broken as detailed in the changelog for the removal.
   - DT suppport for the PL022 and GPIO drivers.
   - pinctrl support for OMAP and PL022."

Pulling from Mark Brown as Grant Likely is still busy moving.

* tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (53 commits)
  spi: remove completely broken Tegra driver
  spi/imx: set the inactive state of the clock according to the clock polarity
  spi/pl022: get/put resources on suspend/resume
  spi/pl022: use more managed resources
  spi/pl022: Devicetree support w/o platform data
  spi/s3c64xx: Don't free controller_data on non-dt platforms
  spi: omap2-mcspi: add pinctrl support
  spi/pl022: adopt pinctrl support
  spi: omap2-mcspi: Cleanup the omap2_mcspi_txrx_dma function
  spi/gpio: Fix stub for spi_gpio_probe_dt()
  spi/mxs: Make the SPI block clock speed configurable via DT
  spi: spi-sh-hspi: drop frees of devm_ alloc'd data
  spi/pl022: Fix chipselects pointer computation
  spi: spi-tle62x0: Use module_spi_driver macro
  mxs/spi: Rework the mxs_ssp_timeout to be more readable
  mxs/spi: Decrement the DMA/PIO border
  mxs/spi: Increment the transfer length only if transfer succeeded
  mxs/spi: Fix issues when doing long continuous transfer
  spi: spi-gpio: Add DT bindings
  spi: spi-gpio: store chipselect information in private structure
  ...

Pull infiniband updates from Roland Dreier:
 "First batch of InfiniBand/RDMA changes for the 3.7 merge window:
   - mlx4 IB support for SR-IOV
   - A couple of SRP initiator fixes
   - Batch of nes hardware driver fixes
   - Fix for long-standing use-after-free crash in IPoIB
   - Other miscellaneous fixes"

This merge also removes a new use of __cancel_delayed_work(), and
replaces it with the regular cancel_delayed_work() that is now irq-safe
thanks to the workqueue updates.

That said, I suspect the sequence in question should probably use
"mod_delayed_work()".  I just did the minimal "don't use deprecated
functions" fixup, though.

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (45 commits)
  IB/qib: Fix local access validation for user MRs
  mlx4_core: Disable SENSE_PORT for multifunction devices
  mlx4_core: Clean up enabling of SENSE_PORT for older (ConnectX-1/-2) HCAs
  mlx4_core: Stash PCI ID driver_data in mlx4_priv structure
  IB/srp: Avoid having aborted requests hang
  IB/srp: Fix use-after-free in srp_reset_req()
  IB/qib: Add a qib driver version
  RDMA/nes: Fix compilation error when nes_debug is enabled
  RDMA/nes: Print hardware resource type
  RDMA/nes: Fix for crash when TX checksum offload is off
  RDMA/nes: Cosmetic changes
  RDMA/nes: Fix for incorrect MSS when TSO is on
  RDMA/nes: Fix incorrect resolving of the loopback MAC address
  mlx4_core: Fix crash on uninitialized priv->cmd.slave_sem
  mlx4_core: Trivial cleanups to driver log messages
  mlx4_core: Trivial readability fix: "0X30" -> "0x30"
  IB/mlx4: Create paravirt contexts for VFs when master IB driver initializes
  mlx4: Modify proxy/tunnel QP mechanism so that guests do no calculations
  mlx4: Paravirtualize Node Guids for slaves
  mlx4: Activate SR-IOV mode for IB
  ...

Pull input updates from Dmitry Torokhov:
 "A few drivers were updated with device tree bindings and others got a
  few small cleanups and fixes."

Fix trivial conflict in drivers/input/keyboard/omap-keypad.c due to
changes clashing with a whitespace cleanup.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (28 commits)
  Input: wacom - mark Intuos5 pad as in-prox when touching buttons
  Input: synaptics - adjust threshold for treating position values as negative
  Input: hgpk - use %*ph to dump small buffer
  Input: gpio_keys_polled - fix dt pdata->nbuttons
  Input: Add KD[GS]KBDIACRUC ioctls to the compatible list
  Input: omap-keypad - fixed formatting
  Input: tegra - move platform data header
  Input: wacom - add support for EMR on Cintiq 24HD touch
  Input: s3c2410_ts - make s3c_ts_pmops const
  Input: samsung-keypad - use of_get_child_count() helper
  Input: samsung-keypad - use of_match_ptr()
  Input: uinput - fix formatting
  Input: uinput - specify exact bit sizes on userspace APIs
  Input: uinput - mark failed submission requests as free
  Input: uinput - fix race that can block nonblocking read
  Input: uinput - return -EINVAL when read buffer size is too small
  Input: uinput - take event lock when fetching events from buffer
  Input: get rid of MATCH_BIT() macro
  Input: rotary-encoder - add DT bindings
  Input: rotary-encoder - constify platform data pointers
  ...

Pull pinctrl changes from Linus Walleij:
 "Some of this stuff is hitting arch/arm/* and have been ACKed by the
  ARM SoC folks, or it's device tree bindings pertaining to the specific
  driver.

  These are the bulk pinctrl changes for kernel v3.7:
   - Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
     provide platform config for the Nomadik.
   - Add a driver for the i.MX35.
   - Add a driver for the BCM2835, an advanced GPIO expander.
   - Various fixes and clean-ups and minor improvements for the core,
     Nomadik, pinctr-single, sirf drivers.
   - Some platform config for the ux500."

* tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (27 commits)
  pinctrl: add bcm2835 driver
  pinctrl: clarify idle vs sleep states
  pinctrl/nomadik: use irq_find_mapping()
  pinctrl: sirf: add lost chained_irq_enter and exit in sirfsoc_gpio_handle_irq
  pinctrl: sirf: initialize the irq_chip pointer of pinctrl_gpio_range
  pinctrl: sirf: fix spinlock deadlock in sirfsoc_gpio_set_input
  pinctrl: sirf: add missing pins to pinctrl list
  pinctrl: sirf: fix a typo in sirfsoc_gpio_probe
  pinctrl: pinctrl-single: add debugfs pin h/w state info
  ARM: ux500: 8500: update I2C sleep states pinctrl
  pinctrl: Fix potential memory leak in pinctrl_register_one_pin()
  ARM: ux500: tidy up pin sleep modes
  ARM: ux500: fix spi2 pin group
  pinctrl: imx: remove duplicated const
  pinctrl: document semantics vs GPIO
  ARM: ux500: 8500: use hsit_a_2 group for HSI
  pinctrl: use kasprintf() in pinmux_request_gpio()
  pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux
  pinctrl/nomadik : add MC1_a_2 pin MC1 function group list
  pinctrl: pinctrl-single: Make sure we do not change bits outside of mask
  ...

Pull GPIO changes from Linus Walleij:
 "So this is the LW GPIO patch stack for v3.7:
   - refactoring from Thierry Redding at Arnd Bergmann's request to use
     the seq_file iterator interface in gpiolib.
   - A new driver for Avionic Design's N-bit GPIO expander.
   - Two instances of mutexes replaced by spinlocks from Axel Lin to
     code that is supposed to be fastpath compliant.
   - IRQ demuxer and gpio_to_irq() support for pcf857x by Kuninori
     Morimoto.
   - Dynamic GPIO numbers, device tree support, daisy chaining and some
     other fixes for the 74x164 driver by Maxime Ripard.
   - IRQ domain and device tree support for the tc3589x driver by Lee
     Jones.
   - Some conversion to use managed resources devm_* code.
   - Some instances of clk_prepare() or clk_prepare_enable() added to
     support the new, stricter common clock framework.
   - Some for_each_set_bit() simplifications.
   - Then a lot of fixes as we fixed up all of the above tripping over
     our own shoelaces and that kind of thing."

* tag 'gpio-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (34 commits)
  gpio: pcf857x: select IRQ_DOMAIN
  gpio: Document device_node's det_debounce
  gpio-lpc32xx: Add GPI_28
  gpio: adnp: dt: Reference generic interrupt binding
  gpio: Add Avionic Design N-bit GPIO expander support
  gpio: pxa: using for_each_set_bit to simplify the code
  gpio_msm: using for_each_set_bit to simplify the code
  gpio: Enable the tc3298x GPIO expander driver for Device Tree
  gpio: Provide the tc3589x GPIO expander driver with an IRQ domain
  ARM: shmobile: kzm9g: use gpio-keys instead of gpio-keys-polled
  gpio: pcf857x: fixup smatch WARNING
  gpio: 74x164: Add support for the daisy-chaining
  gpio: 74x164: dts: Add documentation for the dt binding
  dt: Fix incorrect reference in gpio-led documentation
  gpio: 74x164: Add device tree support
  gpio: 74x164: Use dynamic gpio number assignment if no pdata is present
  gpio: 74x164: Use devm_kzalloc
  gpio: 74x164: Use module_spi_driver boiler plate function
  gpio: sx150x: Use irq_data_get_irq_chip_data() at appropriate places
  gpio: em: Use irq_data_get_irq_chip_data() at appropriate places
  ...

The network merge brought in a few users of functions that got
deprecated by the workqueue cleanups: the 'system_nrt_wq' is now the
same as the regular system_wq, since all workqueues are now non-
reentrant.

Similarly, remove one use of flush_work_sync() - the regular
flush_work() has become synchronous, and the "_sync()" version is thus
deprecated as being superfluous.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking changes from David Miller:

 1) GRE now works over ipv6, from Dmitry Kozlov.

 2) Make SCTP more network namespace aware, from Eric Biederman.

 3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.

 4) Make openvswitch network namespace aware, from Pravin B Shelar.

 5) IPV6 NAT implementation, from Patrick McHardy.

 6) Server side support for TCP Fast Open, from Jerry Chu and others.

 7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
    Borkmann.

 8) Increate the loopback default MTU to 64K, from Eric Dumazet.

 9) Use a per-task rather than per-socket page fragment allocator for
    outgoing networking traffic.  This benefits processes that have very
    many mostly idle sockets, which is quite common.

    From Eric Dumazet.

10) Use up to 32K for page fragment allocations, with fallbacks to
    smaller sizes when higher order page allocations fail.  Benefits are
    a) less segments for driver to process b) less calls to page
    allocator c) less waste of space.

    From Eric Dumazet.

11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.

12) VXLAN device driver, one way to handle VLAN issues such as the
    limitation of 4096 VLAN IDs yet still have some level of isolation.
    From Stephen Hemminger.

13) As usual there is a large boatload of driver changes, with the scale
    perhaps tilted towards the wireless side this time around.

Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
  hyperv: Add buffer for extended info after the RNDIS response message.
  hyperv: Report actual status in receive completion packet
  hyperv: Remove extra allocated space for recv_pkt_list elements
  hyperv: Fix page buffer handling in rndis_filter_send_request()
  hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
  hyperv: Fix the max_xfer_size in RNDIS initialization
  vxlan: put UDP socket in correct namespace
  vxlan: Depend on CONFIG_INET
  sfc: Fix the reported priorities of different filter types
  sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
  sfc: Fix loopback self-test with separate_tx_channels=1
  sfc: Fix MCDI structure field lookup
  sfc: Add parentheses around use of bitfield macro arguments
  sfc: Fix null function pointer in efx_sriov_channel_type
  vxlan: virtual extensible lan
  igmp: export symbol ip_mc_leave_group
  netlink: add attributes to fdb interface
  tg3: unconditionally select HWMON support when tg3 is enabled.
  Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
  gre: fix sparse warning
  ...

Pull sparc updates from David Miller:
 "Largely this is simply adding support for the Niagara 4 cpu.

  Major areas are perf events (chip now supports 4 counters and can
  monitor any event on each counter), crypto (opcodes are availble for
  sha1, sha256, sha512, md5, crc32c, AES, DES, CAMELLIA, and Kasumi
  although the last is unsupported since we lack a generic crypto layer
  Kasumi implementation), and an optimized memcpy.

  Finally some cleanups by Peter Senna Tschudin."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next: (47 commits)
  sparc64: Fix trailing whitespace in NG4 memcpy.
  sparc64: Fix comment type in NG4 copy from user.
  sparc64: Add SPARC-T4 optimized memcpy.
  drivers/sbus/char: removes unnecessary semicolon
  arch/sparc/kernel/pci_sun4v.c: removes unnecessary semicolon
  sparc64: Fix function argument comment in camellia_sparc64_key_expand asm.
  sparc64: Fix IV handling bug in des_sparc64_cbc_decrypt
  sparc64: Add auto-loading mechanism to crypto-opcode drivers.
  sparc64: Add missing pr_fmt define to crypto opcode drivers.
  sparc64: Adjust crypto priorities.
  sparc64: Use cpu_pgsz_mask for linear kernel mapping config.
  sparc64: Probe cpu page size support more portably.
  sparc64: Support 2GB and 16GB page sizes for kernel linear mappings.
  sparc64: Fix bugs in unrolled 256-bit loops.
  sparc64: Avoid code duplication in crypto assembler.
  sparc64: Unroll CTR crypt loops in AES driver.
  sparc64: Unroll ECB decryption loops in AES driver.
  sparc64: Unroll ECB encryption loops in AES driver.
  sparc64: Add ctr mode support to AES driver.
  sparc64: Move AES driver over to a methods based implementation.
  ...

In some response messages, there may be some extended info after the
message.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existing code always reports NVSP_STAT_SUCCESS. This patch adds the
mechanism to report failure when it happens.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The receive code path doesn't use the page buffer, so remove the
extra allocated space here.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To prevent possible data corruption in RNDIS requests, add another
page buffer if the request message crossed page boundary.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return ETIMEDOUT when the reply message is not received in time.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to RNDIS specs, Windows sets this size to
0x4000. I use the same value here.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move vxlan UDP socket to correct network namespace
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull user namespace changes from Eric Biederman:
 "This is a mostly modest set of changes to enable basic user namespace
  support.  This allows the code to code to compile with user namespaces
  enabled and removes the assumption there is only the initial user
  namespace.  Everything is converted except for the most complex of the
  filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
  nfs, ocfs2 and xfs as those patches need a bit more review.

  The strategy is to push kuid_t and kgid_t values are far down into
  subsystems and filesystems as reasonable.  Leaving the make_kuid and
  from_kuid operations to happen at the edge of userspace, as the values
  come off the disk, and as the values come in from the network.
  Letting compile type incompatible compile errors (present when user
  namespaces are enabled) guide me to find the issues.

  The most tricky areas have been the places where we had an implicit
  union of uid and gid values and were storing them in an unsigned int.
  Those places were converted into explicit unions.  I made certain to
  handle those places with simple trivial patches.

  Out of that work I discovered we have generic interfaces for storing
  quota by projid.  I had never heard of the project identifiers before.
  Adding full user namespace support for project identifiers accounts
  for most of the code size growth in my git tree.

  Ultimately there will be work to relax privlige checks from
  "capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
  root in a user names to do those things that today we only forbid to
  non-root users because it will confuse suid root applications.

  While I was pushing kuid_t and kgid_t changes deep into the audit code
  I made a few other cleanups.  I capitalized on the fact we process
  netlink messages in the context of the message sender.  I removed
  usage of NETLINK_CRED, and started directly using current->tty.

  Some of these patches have also made it into maintainer trees, with no
  problems from identical code from different trees showing up in
  linux-next.

  After reading through all of this code I feel like I might be able to
  win a game of kernel trivial pursuit."

Fix up some fairly trivial conflicts in netfilter uid/git logging code.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
  userns: Convert the ufs filesystem to use kuid/kgid where appropriate
  userns: Convert the udf filesystem to use kuid/kgid where appropriate
  userns: Convert ubifs to use kuid/kgid
  userns: Convert squashfs to use kuid/kgid where appropriate
  userns: Convert reiserfs to use kuid and kgid where appropriate
  userns: Convert jfs to use kuid/kgid where appropriate
  userns: Convert jffs2 to use kuid and kgid where appropriate
  userns: Convert hpfs to use kuid and kgid where appropriate
  userns: Convert btrfs to use kuid/kgid where appropriate
  userns: Convert bfs to use kuid/kgid where appropriate
  userns: Convert affs to use kuid/kgid wherwe appropriate
  userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
  userns: On ia64 deal with current_uid and current_gid being kuid and kgid
  userns: On ppc convert current_uid from a kuid before printing.
  userns: Convert s390 getting uid and gid system calls to use kuid and kgid
  userns: Convert s390 hypfs to use kuid and kgid where appropriate
  userns: Convert binder ipc to use kuids
  userns: Teach security_path_chown to take kuids and kgids
  userns: Add user namespace support to IMA
  userns: Convert EVM to deal with kuids and kgids in it's hmac computation
  ...

Pull cgroup hierarchy update from Tejun Heo:
 "Currently, different cgroup subsystems handle nested cgroups
  completely differently.  There's no consistency among subsystems and
  the behaviors often are outright broken.

  People at least seem to agree that the broken hierarhcy behaviors need
  to be weeded out if any progress is gonna be made on this front and
  that the fallouts from deprecating the broken behaviors should be
  acceptable especially given that the current behaviors don't make much
  sense when nested.

  This patch makes cgroup emit warning messages if cgroups for
  subsystems with broken hierarchy behavior are nested to prepare for
  fixing them in the future.  This was put in a separate branch because
  more related changes were expected (didn't make it this round) and the
  memory cgroup wanted to pull in this and make changes on top."

* 'for-3.7-hierarchy' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: mark subsystems with broken hierarchy support and whine if cgroups are nested for them

Pull cgroup updates from Tejun Heo:

 - xattr support added.  The implementation is shared with tmpfs.  The
   usage is restricted and intended to be used to manage per-cgroup
   metadata by system software.  tmpfs changes are routed through this
   branch with Hugh's permission.

 - cgroup subsystem ID handling simplified.

* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: Define CGROUP_SUBSYS_COUNT according the configuration
  cgroup: Assign subsystem IDs during compile time
  cgroup: Do not depend on a given order when populating the subsys array
  cgroup: Wrap subsystem selection macro
  cgroup: Remove CGROUP_BUILTIN_SUBSYS_COUNT
  cgroup: net_prio: Do not define task_netpioidx() when not selected
  cgroup: net_cls: Do not define task_cls_classid() when not selected
  cgroup: net_cls: Move sock_update_classid() declaration to cls_cgroup.h
  cgroup: trivial fixes for Documentation/cgroups/cgroups.txt
  xattr: mark variable as uninitialized to make both gcc and smatch happy
  fs: add missing documentation to simple_xattr functions
  cgroup: add documentation on extended attributes usage
  cgroup: rename subsys_bits to subsys_mask
  cgroup: add xattr support
  cgroup: revise how we re-populate root directory
  xattr: extract simple_xattr code from tmpfs

Pull workqueue changes from Tejun Heo:
 "This is workqueue updates for v3.7-rc1.  A lot of activities this
  round including considerable API and behavior cleanups.

   * delayed_work combines a timer and a work item.  The handling of the
     timer part has always been a bit clunky leading to confusing
     cancelation API with weird corner-case behaviors.  delayed_work is
     updated to use new IRQ safe timer and cancelation now works as
     expected.

   * Another deficiency of delayed_work was lack of the counterpart of
     mod_timer() which led to cancel+queue combinations or open-coded
     timer+work usages.  mod_delayed_work[_on]() are added.

     These two delayed_work changes make delayed_work provide interface
     and behave like timer which is executed with process context.

   * A work item could be executed concurrently on multiple CPUs, which
     is rather unintuitive and made flush_work() behavior confusing and
     half-broken under certain circumstances.  This problem doesn't
     exist for non-reentrant workqueues.  While non-reentrancy check
     isn't free, the overhead is incurred only when a work item bounces
     across different CPUs and even in simulated pathological scenario
     the overhead isn't too high.

     All workqueues are made non-reentrant.  This removes the
     distinction between flush_[delayed_]work() and
     flush_[delayed_]_work_sync().  The former is now as strong as the
     latter and the specified work item is guaranteed to have finished
     execution of any previous queueing on return.

   * In addition to the various bug fixes, Lai redid and simplified CPU
     hotplug handling significantly.

   * Joonsoo introduced system_highpri_wq and used it during CPU
     hotplug.

  There are two merge commits - one to pull in IRQ safe timer from
  tip/timers/core and the other to pull in CPU hotplug fixes from
  wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."

Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.

Tejun pointed out a few of them, I fixed a couple more.

* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
  workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
  workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
  workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
  workqueue: remove @delayed from cwq_dec_nr_in_flight()
  workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
  workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
  workqueue: use __cpuinit instead of __devinit for cpu callbacks
  workqueue: rename manager_mutex to assoc_mutex
  workqueue: WORKER_REBIND is no longer necessary for idle rebinding
  workqueue: WORKER_REBIND is no longer necessary for busy rebinding
  workqueue: reimplement idle worker rebinding
  workqueue: deprecate __cancel_delayed_work()
  workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
  workqueue: use mod_delayed_work() instead of __cancel + queue
  workqueue: use irqsafe timer for delayed_work
  workqueue: clean up delayed_work initializers and add missing one
  workqueue: make deferrable delayed_work initializer names consistent
  workqueue: cosmetic whitespace updates for macro definitions
  workqueue: deprecate system_nrt[_freezable]_wq
  workqueue: deprecate flush[_delayed]_work_sync()
  ...