- 12 Apr, 2017 12 commits
-
-
David Hildenbrand authored
Let's just move it to the place where it is actually needed. Signed-off-by:
David Hildenbrand <david@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com>
-
David Hildenbrand authored
I don't see any reason any more for this lock, seemed to be used to protect removal of kvm->arch.vpic / kvm->arch.vioapic when already partially inititalized, now access is properly protected using kvm->arch.irqchip_mode and this shouldn't be necessary anymore. Signed-off-by:
-
David Hildenbrand authored
Signed-off-by:
-
David Hildenbrand authored
When handling KVM_GET_IRQCHIP, we already check irqchip_kernel(), which implies a fully inititalized ioapic. Signed-off-by:
-
David Hildenbrand authored
Signed-off-by:
-
David Hildenbrand authored
Let's just use kvm->arch.vioapic directly. Signed-off-by:
-
David Hildenbrand authored
It seemed like a nice idea to encapsulate access to kvm->arch.vpic. But as the usage is already mixed, internal locks are taken outside of i8259.c and grepping for "vpic" only is much easier, let's just get rid of pic_irqchip(). Signed-off-by:
-
David Hildenbrand authored
KVM_IRQCHIP_KERNEL implies a fully inititalized ioapic, while kvm->arch.vioapic might temporarily be set but invalidated again if e.g. setting of default routing fails when setting KVM_CREATE_IRQCHIP. Signed-off-by:
-
David Hildenbrand authored
Let's avoid checking against kvm->arch.vpic. We have kvm->arch.irqchip_mode for that now. KVM_IRQCHIP_KERNEL implies a fully inititalized pic, while kvm->arch.vpic might temporarily be set but invalidated again if e.g. kvm_ioapic_init() fails when setting KVM_CREATE_IRQCHIP. Although current users seem to be fine, this avoids future bugs. Signed-off-by:
-
David Hildenbrand authored
Let's replace the checks for pic_in_kernel() and ioapic_in_kernel() by checks against irqchip_mode. Also make sure that creation of any route is only possible if we have an lapic in kernel (irqchip_in_kernel()) or if we are currently inititalizing the irqchip. This is necessary to switch pic_in_kernel() and ioapic_in_kernel() to irqchip_mode, too. Signed-off-by:
-
David Hildenbrand authored
Let's add a new mode and set it while we create the irqchip via KVM_CREATE_IRQCHIP and KVM_CAP_SPLIT_IRQCHIP. This mode will be used later to test if adding routes (in kvm_set_routing_entry()) is already allowed. Signed-off-by:
-
David Hildenbrand authored
Avoid races between KVM_SET_GSI_ROUTING and KVM_CREATE_IRQCHIP by taking the kvm->lock when setting up routes. If KVM_CREATE_IRQCHIP fails, KVM_SET_GSI_ROUTING could have already set up routes pointing at pic/ioapic, being silently removed already. Also, as a side effect, this patch makes sure that KVM_SET_GSI_ROUTING and KVM_CAP_SPLIT_IRQCHIP cannot run in parallel. Signed-off-by:
-
- 11 Apr, 2017 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linuxRadim Krčmář authored
From: Christian Borntraeger <borntraeger@de.ibm.com> KVM: s390: features for 4.12 1. guarded storage support for guests This contains an s390 base Linux feature branch that is necessary to implement the KVM part 2. Provide an interface to implement adapter interruption suppression which is necessary for proper zPCI support 3. Use more defines instead of numbers 4. Provide logging for lazy enablement of runtime instrumentation
-
- 07 Apr, 2017 16 commits
-
-
Jim Mattson authored
The userspace exception injection API and code path are entirely unprepared for exceptions that might cause a VM-exit from L2 to L1, so the best course of action may be to simply disallow this for now. 1. The API provides no mechanism for userspace to specify the new DR6 bits for a #DB exception or the new CR2 value for a #PF exception. Presumably, userspace is expected to modify these registers directly with KVM_SET_SREGS before the next KVM_RUN ioctl. However, in the event that L1 intercepts the exception, these registers should not be changed. Instead, the new values should be provided in the exit_qualification field of vmcs12 (Intel SDM vol 3, section 27.1). 2. In the case of a userspace-injected #DB, inject_pending_event() clears DR7.GD before calling vmx_queue_exception(). However, in the event that L1 intercepts the exception, this is too early, because DR7.GD should not be modified by a #DB that causes a VM-exit directly (Intel SDM vol 3, section 27.1). 3. If the injected exception is a #PF, nested_vmx_check_exception() doesn't properly check whether or not L1 is interested in the associated error code (using the #PF error code mask and match fields from vmcs12). It may either return 0 when it should call nested_vmx_vmexit() or vice versa. 4. nested_vmx_check_exception() assumes that it is dealing with a hardware-generated exception intercept from L2, with some of the relevant details (the VM-exit interruption-information and the exit qualification) live in vmcs02. For userspace-injected exceptions, this is not the case. 5. prepare_vmcs12() assumes that when its exit_intr_info argument specifies valid information with a valid error code that it can VMREAD the VM-exit interruption error code from vmcs02. For userspace-injected exceptions, this is not the case. Signed-off-by:
Jim Mattson <jmattson@google.com> Signed-off-by:
-
David Hildenbrand authored
If we already entered/are about to enter SMM, don't allow switching to INIT/SIPI_RECEIVED, otherwise the next call to kvm_apic_accept_events() will report a warning. Same applies if we are already in MP state INIT_RECEIVED and SMM is requested to be turned on. Refuse to set the VCPU events in this case. Fixes: cd7764fe ("KVM: x86: latch INITs while in system management mode") Cc: stable@vger.kernel.org # 4.2+ Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Paolo Bonzini authored
Its value has never changed; we might as well make it part of the ABI instead of using the return value of KVM_CHECK_EXTENSION(KVM_CAP_COALESCED_MMIO). Because PPC does not always make MMIO available, the code has to be made dependent on CONFIG_KVM_MMIO rather than KVM_COALESCED_MMIO_PAGE_OFFSET. Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Paolo Bonzini authored
Remove code from architecture files that can be moved to virt/kvm, since there is already common code for coalesced MMIO. Signed-off-by:
-
Paolo Bonzini authored
Signed-off-by:
-
Paolo Bonzini authored
In order to simplify adding exit reasons in the future, the array of exit reason names is now also sorted by exit reason code. Reviewed-by:
-
Paolo Bonzini authored
Now use bit 6 of EPTP to optionally enable A/D bits for EPTP. Another thing to change is that, when EPT accessed and dirty bits are not in use, VMX treats accesses to guest paging structures as data reads. When they are in use (bit 6 of EPTP is set), they are treated as writes and the corresponding EPT dirty bit is set. The MMU didn't know this detail, so this patch adds it. We also have to fix up the exit qualification. It may be wrong because KVM sets bit 6 but the guest might not. L1 emulates EPT A/D bits using write permissions, so in principle it may be possible for EPT A/D bits to be used by L1 even though not available in hardware. The problem is that guest page-table walks will be treated as reads rather than writes, so they would not cause an EPT violation. Signed-off-by:
-
Paolo Bonzini authored
This prepares the MMU paging code for EPT accessed and dirty bits, which can be enabled optionally at runtime. Code that updates the accessed and dirty bits will need a pointer to the struct kvm_mmu. Signed-off-by:
-
Paolo Bonzini authored
handle_ept_violation is checking for "guest-linear-address invalid" + "not a paging-structure walk". However, _all_ EPT violations without a valid guest linear address are paging structure walks, because those EPT violations happen when loading the guest PDPTEs. Therefore, the check can never be true, and even if it were, KVM doesn't care about the guest linear address; it only uses the guest *physical* address VMCS field. So, remove the check altogether. Signed-off-by:
-
Paolo Bonzini authored
Large pages at the PDPE level can be emulated by the MMU, so the bit can be set unconditionally in the EPT capabilities MSR. The same is true of 2MB EPT pages, though all Intel processors with EPT in practice support those. Reviewed-by:
-
Paolo Bonzini authored
Legacy device assignment has been deprecated since 4.2 (released 1.5 years ago). VFIO is better and everyone should have switched to it. If they haven't, this should convince them. :) Reviewed-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Paolo Bonzini authored
Virtual NMIs are only missing in Prescott and Yonah chips. Both are obsolete for virtualization usage---Yonah is 32-bit only even---so drop vNMI emulation. Signed-off-by: -
Borislav Petkov authored
MCG_CAP[63:9] bits are reserved on AMD. However, on an AMD guest, this MSR returns 0x100010a. More specifically, bit 24 is set, which is simply wrong. That bit is MCG_SER_P and is present only on Intel. Thus, clean up the reserved bits in order not to confuse guests. Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: Joerg Roedel <joro@8bytes.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
David Hildenbrand authored
Let's combine it in a single function vmx_switch_vmcs(). Signed-off-by:
-
Jim Mattson authored
According to the Intel SDM, volume 3, section 28.3.2: Creating and Using Cached Translation Information, "No linear mappings are used while EPT is in use." INVEPT will invalidate both the guest-physical mappings and the combined mappings in the TLBs and paging-structure caches, so an INVVPID is superfluous. Signed-off-by:
-
Yi Min Zhao authored
Introduce a cap to enable AIS facility bit, and add documentation for this capability. Signed-off-by:
Yi Min Zhao <zyimin@linux.vnet.ibm.com> Signed-off-by:
Fei Li <sherrylf@linux.vnet.ibm.com> Reviewed-by:
Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com>
-
- 06 Apr, 2017 4 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/kvm-mipsRadim Krčmář authored
From: James Hogan <james.hogan@imgtec.com> KVM: MIPS: VZ support, Octeon III, and TLBR Add basic support for the MIPS Virtualization Module (generally known as MIPS VZ) in KVM. We primarily support the ImgTec P5600, P6600, I6400, and Cavium Octeon III cores so far. Support is included for the following VZ / guest hardware features: - MIPS32 and MIPS64, r5 (VZ requires r5 or later) and r6 - TLBs with GuestID (IMG cores) or Root ASID Dealias (Octeon III) - Shared physical root/guest TLB (IMG cores) - FPU / MSA - Cop0 timer (up to 1GHz for now due to soft timer limit) - Segmentation control (EVA) - Hardware page table walker (HTW) both for root and guest TLB Also included is a proper implementation of the TLBR instruction for the trap & emulate MIPS KVM implementation. Preliminary MIPS architecture changes are applied directly with Ralf's ack.
-
Yi Min Zhao authored
Inject adapter interrupts on a specified adapter which allows to retrieve the adapter flags, e.g. if the adapter is subject to AIS facility or not. And add documentation for this interface. For adapters subject to AIS, handle the airq injection suppression for a given ISC according to the interruption mode: - before injection, if NO-Interruptions Mode, just return 0 and suppress, otherwise, allow the injection. - after injection, if SINGLE-Interruption Mode, change it to NO-Interruptions Mode to suppress the following interrupts. Besides, add tracepoint for suppressed airq and AIS mode transitions. Signed-off-by:
-
Fei Li authored
Provide an interface for userspace to modify AIS (adapter-interruption-suppression) mode state, and add documentation for the interface. Allowed target modes are ALL-Interruptions mode and SINGLE-Interruption mode. We introduce the 'simm' and 'nimm' fields in kvm_s390_float_interrupt to store interruption modes for each ISC. Each bit in 'simm' and 'nimm' targets to one ISC, and collaboratively indicate three modes: ALL-Interruptions, SINGLE-Interruption and NO-Interruptions. This interface can initiate most transitions between the states; transition from SINGLE-Interruption to NO-Interruptions via adapter interrupt injection will be introduced in a following patch. The meaningful combinations are as follows: interruption mode | simm bit | nimm bit ------------------|----------|---------- ALL | 0 | 0 SINGLE | 1 | 0 NO | 1 | 1 Besides, add tracepoint to track AIS mode transitions. Co-Authored-By: -
Fei Li authored
In order to properly implement adapter-interruption suppression, we need a way for userspace to specify which adapters are subject to suppression. Let's convert the existing (and unused) 'pad' field into a 'flags' field and define a flag value for suppressible adapters. Besides, add documentation for the interface. Signed-off-by:
-
- 29 Mar, 2017 7 commits
-
-
Stefan Raspl authored
Add column '%Total' next to 'Total' for easier comparison of numbers between hosts. Signed-off-by:
Stefan Raspl <raspl@linux.vnet.ibm.com> Marc Hartmayer <mhartmay@linux.vnet.ibm.com> Signed-off-by:
-
Stefan Raspl authored
Provide an interactive command to reset the tracepoint statistics. Requires some extra work for debugfs, as the counters cannot be reset. On the up side, this offers us the opportunity to have debugfs values reset on startup and whenever a filter is modified, becoming consistent with the tracepoint provider. As a bonus, 'kvmstat -dt' will now provide useful output, instead of mixing values in totally different orders of magnitude. Furthermore, we avoid unnecessary resets when any of the filters is "changed" interactively to the previous value. Signed-off-by:
Janosch Frank <frankja@linux.vnet.ibm.com> Signed-off-by:
-
Stefan Raspl authored
Provide a real simple way to erase any active filter. Signed-off-by:
Marc Hartmayer <mhartmay@linux.vnet.ibm.com> Signed-off-by:
-
Stefan Raspl authored
Add a new option '-g'/'--guest' to select a particular process by providing the QEMU guest name. Notes: - The logic to figure out the pid corresponding to the guest name might look scary, but works pretty reliably in practice; in the unlikely event that it returns add'l flukes, it will bail out and hint at using '-p' instead, no harm done. - Mixing '-g' and '-p' is possible, and the final instance specified on the command line is the significant one. This is consistent with current behavior for '-p' which, if specified multiple times, also regards the final instance as the significant one. Signed-off-by:
-
Stefan Raspl authored
Behavior on empty/0 input for regex and pid filtering was inconsistent, as the former would keep the current filter, while the latter would (naturally) remove any pid filtering. Make things consistent by falling back to the default filter on empty input for the regex filter dialogue. Signed-off-by:
-
Stefan Raspl authored
If a user defines a regex filter through the interactive command, display the active regex in the header's second line. Signed-off-by:
-
Stefan Raspl authored
Print helpful messages in case users enter invalid input or invalid pids in the interactive pid filter dialogue. Signed-off-by:
-
