- 21 Jun, 2021 23 commits
-
-
Joel Stanley authored
This allows microwatt's kernel to be built with an embedded device tree. Load to arch/powerpc/boot/dtbImage.microwatt to 0x500000: mw_debug -b fpga stop load arch/powerpc/boot/dtbImage.microwatt 500000 start Signed-off-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Reviewed-by:
Segher Boessenkool <segher@kernel.crashing.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/YMwX19wym3kQ7guu@thinks.paulus.ozlabs.org
-
Benjamin Herrenschmidt authored
This fixes the core devtree.c functions and the ns16550 UART backend. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Nicholas Piggin <npiggin@gmail.com> Signed-off-by:
-
Paul Mackerras authored
Signed-off-by:
-
Paul Mackerras authored
Microwatt's hardware RNG is accessed using the DARN instruction. Signed-off-by:
-
Benjamin Herrenschmidt authored
This adds support to the Microwatt platform to use the standard 16550-style UART which available in the standalone Microwatt FPGA. Signed-off-by:
-
Benjamin Herrenschmidt authored
This is a simple native ICS backend that matches the layout of the Microwatt implementation of ICS. Signed-off-by:
-
Benjamin Herrenschmidt authored
Just like any other embedded platform. Add an empty soc node. Signed-off-by:
-
Paul Mackerras authored
Microwatt currently runs with MSR[HV] = 0, hence the usable-privilege properties don't have bit 2 (for HV support) set, and we need the /chosen/ibm,architecture-vec-5 property. Signed-off-by:
-
Paul Mackerras authored
Microwatt is a FPGA-based implementation of the Power ISA. It currently only implements little-endian 64-bit mode, and does not (yet) support SMP, VMX, VSX or transactional memory. It has an optional FPU, and an optional MMU (required for running Linux, obviously) which implements a configurable radix tree but not hypervisor mode or nested radix translation. This adds a new machine type to support FPGA-based SoCs with a Microwatt core. CONFIG_MATH_EMULATION can be selected for Microwatt SOCs which don't have the FPU. Signed-off-by:
-
Christophe Leroy authored
Use set_memory_attr() instead of the PPC32 specific change_page_attr() change_page_attr() was checking that the address was not mapped by blocks and was handling highmem, but that's unneeded because the affected pages can't be in highmem and block mapping verification is already done by the callers. Signed-off-by:
Christophe Leroy <christophe.leroy@csgroup.eu> [ruscur: rebase on powerpc/merge with Christophe's new patches] Signed-off-by:
Russell Currey <ruscur@russell.cc> Signed-off-by:
Jordan Niethe <jniethe5@gmail.com> Signed-off-by:
-
Christophe Leroy authored
In addition to the set_memory_xx() functions which allows to change the memory attributes of not (yet) used memory regions, implement a set_memory_attr() function to: - set the final memory protection after init on currently used kernel regions. - enable/disable kernel memory regions in the scope of DEBUG_PAGEALLOC. Unlike the set_memory_xx() which can act in three step as the regions are unused, this function must modify 'on the fly' as the kernel is executing from them. At the moment only PPC32 will use it and changing page attributes on the fly is not an issue. Reported-by:
kbuild test robot <lkp@intel.com> [ruscur: cast "data" to unsigned long instead of int] Signed-off-by:
-
Russell Currey authored
To enable strict module RWX on powerpc, set: CONFIG_STRICT_MODULE_RWX=y You should also have CONFIG_STRICT_KERNEL_RWX=y set to have any real security benefit. ARCH_HAS_STRICT_MODULE_RWX is set to require ARCH_HAS_STRICT_KERNEL_RWX. This is due to a quirk in arch/Kconfig and arch/powerpc/Kconfig that makes STRICT_MODULE_RWX *on by default* in configurations where STRICT_KERNEL_RWX is *unavailable*. Since this doesn't make much sense, and module RWX without kernel RWX doesn't make much sense, having the same dependencies as kernel RWX works around this problem. Book3s/32 603 and 604 core processors are not able to write protect kernel pages so do not set ARCH_HAS_STRICT_MODULE_RWX for Book3s/32. [jpn: - predicate on !PPC_BOOK3S_604 - make module_alloc() use PAGE_KERNEL protection] Signed-off-by: -
Jordan Niethe authored
Add the necessary call to bpf_jit_binary_lock_ro() to remove write and add exec permissions to the JIT image after it has finished being written. Without CONFIG_STRICT_MODULE_RWX the image will be writable and executable until the call to bpf_jit_binary_lock_ro(). Signed-off-by:
-
Jordan Niethe authored
Commit 74451e66 ("bpf: make jited programs visible in traces") added a default bpf_jit_free() implementation. Powerpc did not use the default bpf_jit_free() as powerpc did not set the images read-only. The default bpf_jit_free() called bpf_jit_binary_unlock_ro() is why it could not be used for powerpc. Commit d53d2f78 ("bpf: Use vmalloc special flag") moved keeping track of read-only memory to vmalloc. This included removing bpf_jit_binary_unlock_ro(). Therefore there is no reason powerpc needs its own bpf_jit_free(). Remove it. Signed-off-by:
-
Russell Currey authored
Add the arch specific insn page allocator for powerpc. This allocates ROX pages if STRICT_KERNEL_RWX is enabled. These pages are only written to with patch_instruction() which is able to write RO pages. Signed-off-by:
Daniel Axtens <dja@axtens.net> Signed-off-by:
-
Jordan Niethe authored
Make module_alloc() use PAGE_KERNEL protections instead of PAGE_KERNEL_EXEX if Strict Module RWX is enabled. Signed-off-by:
-
Jordan Niethe authored
setup_text_poke_area() is a late init call so it runs before mark_rodata_ro() and after the init calls. This lets all the init code patching simply write to their locations. In the future, kprobes is going to allocate its instruction pages RO which means they will need setup_text__poke_area() to have been already called for their code patching. However, init_kprobes() (which allocates and patches some instruction pages) is an early init call so it happens before setup_text__poke_area(). start_kernel() calls poking_init() before any of the init calls. On powerpc, poking_init() is currently a nop. setup_text_poke_area() relies on kernel virtual memory, cpu hotplug and per_cpu_areas being setup. setup_per_cpu_areas(), boot_cpu_hotplug_init() and mm_init() are called before poking_init(). Turn setup_text_poke_area() into poking_init(). Signed-off-by:
-
Russell Currey authored
The set_memory_{ro/rw/nx/x}() functions are required for STRICT_MODULE_RWX, and are generally useful primitives to have. This implementation is designed to be generic across powerpc's many MMUs. It's possible that this could be optimised to be faster for specific MMUs. This implementation does not handle cases where the caller is attempting to change the mapping of the page it is executing from, or if another CPU is concurrently using the page being altered. These cases likely shouldn't happen, but a more complex implementation with MMU-specific code could safely handle them. On hash, the linear mapping is not kept in the linux pagetable, so this will not change the protection if used on that range. Currently these functions are not used on the linear map so just WARN for now. apply_to_existing_page_range() does not work on huge pages so for now disallow changing the protection of huge pages. [jpn: - Allow set memory functions to be used without Strict RWX - Hash: Disallow certain regions - Have change_page_attr() take function pointers to manipulate ptes - Radix: Add ptesync after set_pte_at()] Signed-off-by: -
Nicholas Piggin authored
This allows the hypervisor / firmware to describe this workarounds to the guest. Signed-off-by:
-
Nicholas Piggin authored
Rather than tying this mitigation to RFI L1D flush requirement, add a new bit for it. Signed-off-by:
-
Nicholas Piggin authored
This allows the hypervisor / firmware to describe these workarounds to the guest. Signed-off-by:
-
Nicholas Piggin authored
This prevents spurious rebuilds of the lds and then wrappers. Signed-off-by:
-
Nicholas Piggin authored
POWER9 and POWER10 asynchronous machine checks due to stores have their cause reported in SRR1 but SRR1[42] is set, which in other cases indicates DSISR cause. Check for these cases and clear SRR1[42], so the cause matching uses the i-side (SRR1) table. Fixes: 7b9f71f9 ("powerpc/64s: POWER9 machine check handler") Fixes: 201220bb ("powerpc/powernv: Machine check handler for POWER10") Signed-off-by:
-
- 20 Jun, 2021 17 commits
-
-
Haren Myneni authored
The user space uses /dev/crypto/nx-gzip interface to setup VAS windows, create paste mapping and close windows. This patch adds changes to create/remove this interface with VAS register/unregister functions on PowerVM platform. Signed-off-by:
Haren Myneni <haren@linux.ibm.com> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Acked-by:
-
Haren Myneni authored
Export NX-GZIP capabilities to usrespace in sysfs /sys/devices/vio/ibm,compression-v1/nx_gzip_caps directory. These are queried by userspace accelerator libraries to set minimum length heuristics and maximum limits on request sizes. NX-GZIP capabilities: min_compress_len /*Recommended minimum compress length in bytes*/ min_decompress_len /*Recommended minimum decompress length in bytes*/ req_max_processed_len /* Maximum number of bytes processed in one request */ NX will return RMA_Reject if the request buffer size is greater than req_max_processed_len. Signed-off-by:
-
Haren Myneni authored
The hypervisor provides different NX capabilities that it supports. These capabilities such as recommended minimum compression / decompression lengths and the maximum request buffer size in bytes are used to define the user space NX request. NX will reject the request if the buffer size is more than the maximum buffer size. Whereas compression / decompression lengths are recommended values for better performance. Changes to get NX overall capabilities which points to the specific features that the hypervisor supports. Then retrieve the capabilities for the specific feature (available only for NXGZIP). Signed-off-by:
-
Haren Myneni authored
Rename nx-842-pseries.c to nx-common-pseries.c to add code for new GZIP compression type. The actual functionality is not changed in this patch. Signed-off-by:
-
Haren Myneni authored
NX generates an interrupt when sees a fault on the user space buffer and the hypervisor forwards that interrupt to OS. Then the kernel handles the interrupt by issuing H_GET_NX_FAULT hcall to retrieve the fault CRB information. This patch also adds changes to setup and free IRQ per each window and also handles the fault by updating the CSB. Signed-off-by:
-
Haren Myneni authored
This patch adds VAS window allocatioa/close with the corresponding hcalls. Also changes to integrate with the existing user space VAS API and provide register/unregister functions to NX pseries driver. The driver register function is used to create the user space interface (/dev/crypto/nx-gzip) and unregister to remove this entry. The user space process opens this device node and makes an ioctl to allocate VAS window. The close interface is used to deallocate window. Signed-off-by:
-
Haren Myneni authored
The hypervisor provides VAS capabilities for GZIP default and QoS features. These capabilities gives information for the specific features such as total number of credits available in LPAR, maximum credits allowed per window, maximum credits allowed in LPAR, whether usermode copy/paste is supported, and etc. This patch adds the following: - Retrieve all features that are provided by hypervisor using H_QUERY_VAS_CAPABILITIES hcall with 0 as feature type. - Retrieve capabilities for the specific feature using the same hcall and the feature type (1 for QoS and 2 for default type). Signed-off-by:
-
Haren Myneni authored
This patch adds the following hcall wrapper functions to allocate, modify and deallocate VAS windows, and retrieve VAS capabilities. H_ALLOCATE_VAS_WINDOW: Allocate VAS window H_DEALLOCATE_VAS_WINDOW: Close VAS window H_MODIFY_VAS_WINDOW: Setup window before using H_QUERY_VAS_CAPABILITIES: Get VAS capabilities Signed-off-by:
-
Haren Myneni authored
PowerVM introduces two different type of credits: Default and Quality of service (QoS). The total number of default credits available on each LPAR depends on CPU resources configured. But these credits can be shared or over-committed across LPARs in shared mode which can result in paste command failure (RMA_busy). To avoid NX HW contention, the hypervisor ntroduces QoS credit type which makes sure guaranteed access to NX esources. The system admins can assign QoS credits or each LPAR via HMC. Default credit type is used to allocate a VAS window by default as on PowerVM implementation. But the process can pass VAS_TX_WIN_FLAG_QOS_CREDIT flag with VAS_TX_WIN_OPEN ioctl to open QoS type window. Signed-off-by:
-
Haren Myneni authored
This patch adds hcalls and other definitions. Also define structs that are used in VAS implementation on PowerVM. Signed-off-by:
-
Haren Myneni authored
Many elements in vas_struct are used on PowerNV and PowerVM platforms. vas_window is used for both TX and RX windows on PowerNV and for TX windows on PowerVM. So some elements are specific to these platforms. So this patch defines common vas_window and platform specific window structs (pnv_vas_window on PowerNV). Also adds the corresponding changes in PowerNV vas code. Signed-off-by:
-
Haren Myneni authored
If a coprocessor encounters an error translating an address, the VAS will cause an interrupt in the host. The kernel processes the fault by updating CSB. This functionality is same for both powerNV and pseries. So this patch moves these functions to common vas-api.c and the actual functionality is not changed. Signed-off-by:
-
Haren Myneni authored
Take pid and mm references when each window opens and drops during close. This functionality is needed for powerNV and pseries. So this patch defines the existing code as functions in common book3s platform vas-api.c Signed-off-by:
-
Haren Myneni authored
PowerNV uses registers to open/close VAS windows, and getting the paste address. Whereas the hypervisor calls are used on PowerVM. This patch adds the platform specific user space window operations and register with the common VAS user space interface. Signed-off-by:
-
Haren Myneni authored
powerNV and pseries drivers register / unregister to the corresponding platform specific VAS separately. Then these VAS functions call the common API with the specific window operations. So rename powerNV VAS API register/unregister functions. Signed-off-by:
-
Haren Myneni authored
The pseries platform will share vas and nx code and interfaces with the PowerNV platform, so create the arch/powerpc/platforms/book3s/ directory and move VAS API code there. Functionality is not changed. Signed-off-by:
-
Haren Myneni authored
The kernel handles the NX fault by updating CSB or sending signal to process. In multithread applications, children can open VAS windows and can exit without closing them. But the parent can continue to send NX requests with these windows. To prevent pid reuse, reference will be taken on pid and tgid when the window is opened and release them during window close. The current code is not releasing the tgid reference which can cause pid leak and this patch fixes the issue. Fixes: db1c08a7 ("powerpc/vas: Take reference to PID and mm for user space windows") Cc: stable@vger.kernel.org # 5.8+ Reported-by:
-
