The current pin muxing scheme muxes GPIO_1 pad for USB_OTG_ID
because of which when card is inserted, usb otg is enumerated
and the card is never detected.

[   64.492645] cfg80211: failed to load regulatory.db
[   64.492657] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[   76.343711] ci_hdrc ci_hdrc.0: EHCI Host Controller
[   76.349742] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2
[   76.388862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[   76.396650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[   76.405412] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   76.412763] usb usb2: Product: EHCI Host Controller
[   76.417666] usb usb2: Manufacturer: Linux 5.8.0-rc1-next-20200618 ehci_hcd
[   76.424623] usb usb2: SerialNumber: ci_hdrc.0
[   76.431755] hub 2-0:1.0: USB hub found
[   76.435862] hub 2-0:1.0: 1 port detected

The TRM mentions GPIO_1 pad should be muxed/assigned for card detect
and ENET_RX_ER pad for USB_OTG_ID for proper operation.

This patch fixes pin muxing as per TRM and is tested on a
i.Core 1.5 MX6 DL SOM.

[   22.449165] mmc0: host does not support reading read-only switch, assuming write-enable
[   22.459992] mmc0: new high speed SDHC card at address 0001
[   22.469725] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
[   22.478856]  mmcblk0: p1 p2

Fixes: 6df11287 ("ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual initial support")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Commit 0672d22a ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the
phy-mode for fec1, but missed to fix it for the fec2 node.

Fix fec2 to also use "rgmii-id" as the phy-mode.

Cc: <stable@vger.kernel.org>
Fixes: 0672d22a ("ARM: dts: imx: Fix the AR803X phy-mode")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Commit 0672d22a ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the
phy-mode for fec1, but missed to fix it for the fec2 node.

Fix fec2 to also use "rgmii-id" as the phy-mode.

Cc: <stable@vger.kernel.org>
Fixes: 0672d22a ("ARM: dts: imx: Fix the AR803X phy-mode")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

fsl,ls1021a is a mach under arch/arm/mach-imx/, however it could
not use the soc driver which will break caam on ls1021a platform.

So directly return if it is compatible with fsl,ls1021a.

Fixes: 52102a3b ("soc: imx: move cpu code to drivers/soc/imx")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

No callers of imx_add_imx_dma() need an error IRQ, so they supply 0 as
"irq_err", which means we register a resource of IRQ 0, which is invalid
and causes a warning if used.

Remove the "irq_err" argument altogether so there's no chance of trying to
use the invalid IRQ 0.

Fixes: a85a6c86 ("driver core: platform: Clarify that IRQ 0 is invalid")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: kernel@pengutronix.de
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since commit a85a6c86 ("driver core: platform: Clarify that IRQ 0 is
invalid"), the kernel is a bit touchy when it encounters interrupt 0.
As a result, there are lots of warnings such as the following when booting
systems such as 'kzm'.

WARNING: CPU: 0 PID: 1 at drivers/base/platform.c:224 platform_get_irq_optional+0x118/0x128
0 is an invalid IRQ number
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.8.0-rc3 #1
Hardware name: Kyoto Microcomputer Co., Ltd. KZM-ARM11-01
[<c01127d4>] (unwind_backtrace) from [<c010c620>] (show_stack+0x10/0x14)
[<c010c620>] (show_stack) from [<c06f5f54>] (dump_stack+0xe8/0x120)
[<c06f5f54>] (dump_stack) from [<c0128878>] (__warn+0xe4/0x108)
[<c0128878>] (__warn) from [<c0128910>] (warn_slowpath_fmt+0x74/0xbc)
[<c0128910>] (warn_slowpath_fmt) from [<c08b8e84>] (platform_get_irq_optional+0x118/0x128)
[<c08b8e84>] (platform_get_irq_optional) from [<c08b8eb4>] (platform_irq_count+0x20/0x3c)
[<c08b8eb4>] (platform_irq_count) from [<c0728660>] (mxc_gpio_probe+0x8c/0x494)
[<c0728660>] (mxc_gpio_probe) from [<c08b93cc>] (platform_drv_probe+0x48/0x98)
[<c08b93cc>] (platform_drv_probe) from [<c08b703c>] (really_probe+0x214/0x344)
[<c08b703c>] (really_probe) from [<c08b7274>] (driver_probe_device+0x58/0xb4)
[<c08b7274>] (driver_probe_device) from [<c08b7478>] (device_driver_attach+0x58/0x60)
[<c08b7478>] (device_driver_attach) from [<c08b7504>] (__driver_attach+0x84/0xc0)
[<c08b7504>] (__driver_attach) from [<c08b50f8>] (bus_for_each_dev+0x78/0xb8)
[<c08b50f8>] (bus_for_each_dev) from [<c08b62cc>] (bus_add_driver+0x154/0x1e0)
[<c08b62cc>] (bus_add_driver) from [<c08b82b8>] (driver_register+0x74/0x108)
[<c08b82b8>] (driver_register) from [<c0102320>] (do_one_initcall+0x80/0x3b4)
[<c0102320>] (do_one_initcall) from [<c1501008>] (kernel_init_freeable+0x170/0x208)
[<c1501008>] (kernel_init_freeable) from [<c0e178d4>] (kernel_init+0x8/0x11c)
[<c0e178d4>] (kernel_init) from [<c0100134>] (ret_from_fork+0x14/0x20)

As it turns out, mxc_register_gpio() is a bit lax when setting the
number of resources: it registers a resource with interrupt 0 when in
reality there is no such interrupt. Fix the problem by not declaring
the second interrupt resource if there is no second interrupt.

Fixes: a85a6c86 ("driver core: platform: Clarify that IRQ 0 is invalid")
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The audio codec on the GW551x routes to ssi1.  It fixes audio capture on
the device.

Cc: stable@vger.kernel.org
Fixes: 3117e851 ("ARM: dts: imx: Add TDA19971 HDMI Receiver to GW551x")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix the build warning with x86_64-randconfig
>> drivers/soc/imx/soc-imx8m.c:150:34: warning: unused variable
>> 'imx8_soc_match' [-Wunused-const-variable]
static const struct of_device_id imx8_soc_match[] = { ^

Fixes: fc40200e ("soc: imx: increase build coverage for imx8m soc driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

if of_find_device_by_node() succeed, imx6q_suspend_init() doesn't have a
corresponding put_device(). Thus add a jump target to fix the exception
handling for this function implementation.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

if of_find_device_by_node() succeed, imx_suspend_alloc_ocram() doesn't
have a corresponding put_device(). Thus add a jump target to fix the
exception handling for this function implementation.

Fixes: 1579c7b9 ("ARM: imx53: Set DDR pins to high impedance when in suspend to RAM.")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Correct i.MX8MP UID fuse offset according to fuse map:

UID_LOW: 0x420
UID_HIGH: 0x430

Fixes: fc40200e ("soc: imx: increase build coverage for imx8m soc driver")
Fixes: 18f662a7 ("soc: imx: Add i.MX8MP SoC driver support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The WDOG_ANY signal is connected to the RESET_IN signal of the SoM
and baseboard. It is currently configured as push-pull, which means
that if some external device like a programmer wants to assert the
RESET_IN signal by pulling it to ground, it drives against the high
level WDOG_ANY output of the SoC.

To fix this we set the WDOG_ANY signal to open-drain configuration.
That way we make sure that the RESET_IN can be asserted by the
watchdog as well as by external devices.

Fixes: 1ea4b76c ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The watchdog's WDOG_ANY signal is used to trigger a POR of the SoC,
if a soft reset is issued. As the SoM hardware connects the WDOG_ANY
and the POR signals, the watchdog node itself and the pin
configuration should be part of the common SoM devicetree.
Let's move it from the baseboard's devicetree to its proper place.

Fixes: 1ea4b76c ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

LDO1 and LDO2 settings are wrong and case the voltage to go above the
maximum level of 2.15V permitted by the SoC to 3.0V.

This patch is based on work done on the i.MX8M Mini-EVK which utilizes
the same fix.

Fixes: 593816fa ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Correct ldo1 voltage range from wrong high group(3.0V~3.3V) to low group
(1.6V~1.9V) because the ldo1 should be 1.8V. Actually, two voltage groups
have been supported at bd718x7-regulator driver, hence, just corrrect the
voltage range to 1.6V~3.3V. For ldo2@0.8V, correct voltage range too.
Otherwise, ldo1 would be kept @3.0V and ldo2@0.9V which violate i.mx8mn
datasheet as the below warning log in kernel:

[    0.995524] LDO1: Bringing 1800000uV into 3000000-3000000uV
[    0.999196] LDO2: Bringing 800000uV into 900000-900000uV

Fixes: 3e44dd09 ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support")
Cc: stable@vger.kernel.org
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Correct ldo1 voltage range from wrong high group(3.0V~3.3V) to low group
(1.6V~1.9V) because the ldo1 should be 1.8V. Actually, two voltage groups
have been supported at bd718x7-regulator driver, hence, just corrrect the
voltage range to 1.6V~3.3V. For ldo2@0.8V, correct voltage range too.
Otherwise, ldo1 would be kept @3.0V and ldo2@0.9V which violate i.mx8mm
datasheet as the below warning log in kernel:

[    0.995524] LDO1: Bringing 1800000uV into 3000000-3000000uV
[    0.999196] LDO2: Bringing 800000uV into 900000-900000uV

Fixes: 78cc25fa ("arm64: dts: imx8mm-evk: Add BD71847 PMIC")
Cc: stable@vger.kernel.org
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull SafeSetID update from Micah Morton:
 "Add additional LSM hooks for SafeSetID

  SafeSetID is capable of making allow/deny decisions for set*uid calls
  on a system, and we want to add similar functionality for set*gid
  calls.

  The work to do that is not yet complete, so probably won't make it in
  for v5.8, but we are looking to get this simple patch in for v5.8
  since we have it ready.

  We are planning on the rest of the work for extending the SafeSetID
  LSM being merged during the v5.9 merge window"

* tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux:
  security: Add LSM hooks to set*gid syscalls

The SafeSetID LSM uses the security_task_fix_setuid hook to filter
set*uid() syscalls according to its configured security policy. In
preparation for adding analagous support in the LSM for set*gid()
syscalls, we add the requisite hook here. Tested by putting print
statements in the security_task_fix_setgid hook and seeing them get hit
during kernel boot.
Signed-off-by: Thomas Cedeno <thomascedeno@google.com>
Signed-off-by: Micah Morton <mortonm@chromium.org>

Pull btrfs updates from David Sterba:
 "This reverts the direct io port to iomap infrastructure of btrfs
  merged in the first pull request. We found problems in invalidate page
  that don't seem to be fixable as regressions or without changing iomap
  code that would not affect other filesystems.

  There are four reverts in total, but three of them are followup
  cleanups needed to revert a43a67a2 cleanly. The result is the
  buffer head based implementation of direct io.

  Reverts are not great, but under current circumstances I don't see
  better options"

* tag 'for-5.8-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Revert "btrfs: switch to iomap_dio_rw() for dio"
  Revert "fs: remove dio_end_io()"
  Revert "btrfs: remove BTRFS_INODE_READDIO_NEED_LOCK"
  Revert "btrfs: split btrfs_direct_IO to read and write part"

Pull networking fixes from David Miller:

 1) Fix cfg80211 deadlock, from Johannes Berg.

 2) RXRPC fails to send norigications, from David Howells.

 3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
    Geliang Tang.

 4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.

 5) The ucc_geth driver needs __netdev_watchdog_up exported, from
    Valentin Longchamp.

 6) Fix hashtable memory leak in dccp, from Wang Hai.

 7) Fix how nexthops are marked as FDB nexthops, from David Ahern.

 8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.

 9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.

10) Fix link speed reporting in iavf driver, from Brett Creeley.

11) When a channel is used for XSK and then reused again later for XSK,
    we forget to clear out the relevant data structures in mlx5 which
    causes all kinds of problems. Fix from Maxim Mikityanskiy.

12) Fix memory leak in genetlink, from Cong Wang.

13) Disallow sockmap attachments to UDP sockets, it simply won't work.
    From Lorenz Bauer.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
  net: ethernet: ti: ale: fix allmulti for nu type ale
  net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
  net: atm: Remove the error message according to the atomic context
  bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
  libbpf: Support pre-initializing .bss global variables
  tools/bpftool: Fix skeleton codegen
  bpf: Fix memlock accounting for sock_hash
  bpf: sockmap: Don't attach programs to UDP sockets
  bpf: tcp: Recv() should return 0 when the peer socket is closed
  ibmvnic: Flush existing work items before device removal
  genetlink: clean up family attributes allocations
  net: ipa: header pad field only valid for AP->modem endpoint
  net: ipa: program upper nibbles of sequencer type
  net: ipa: fix modem LAN RX endpoint id
  net: ipa: program metadata mask differently
  ionic: add pcie_print_link_status
  rxrpc: Fix race between incoming ACK parser and retransmitter
  net/mlx5: E-Switch, Fix some error pointer dereferences
  net/mlx5: Don't fail driver on failure to create debugfs
  net/mlx5e: CT: Fix ipv6 nat header rewrite actions
  ...

This reverts commit a43a67a2.

This patch reverts the main part of switching direct io implementation
to iomap infrastructure. There's a problem in invalidate page that
couldn't be solved as regression in this development cycle.

The problem occurs when buffered and direct io are mixed, and the ranges
overlap. Although this is not recommended, filesystems implement
measures or fallbacks to make it somehow work. In this case, fallback to
buffered IO would be an option for btrfs (this already happens when
direct io is done on compressed data), but the change would be needed in
the iomap code, bringing new semantics to other filesystems.

Another problem arises when again the buffered and direct ios are mixed,
invalidation fails, then -EIO is set on the mapping and fsync will fail,
though there's no real error.

There have been discussions how to fix that, but revert seems to be the
least intrusive option.

Link: https://lore.kernel.org/linux-btrfs/20200528192103.xm45qoxqmkw7i5yl@fiona/Signed-off-by: David Sterba <dsterba@suse.com>

On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS allmulti setting does not allow
unregistered mcast packets to pass.

This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
This path was missed by commit 9d1f6447 ("net: ethernet: ti: ale: fix
seeing unreg mcast packets with promisc and allmulti disabled").

Hence, fix it by taking into account ALE type in cpsw_ale_set_allmulti().

Fixes: 9d1f6447 ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ALE parameters structure is created on stack, so it has to be reset
before passing to cpsw_ale_create() to avoid garbage values.

Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2020-06-12

The following pull-request contains BPF updates for your *net* tree.

We've added 26 non-merge commits during the last 10 day(s) which contain
a total of 27 files changed, 348 insertions(+), 93 deletions(-).

The main changes are:

1) sock_hash accounting fix, from Andrey.

2) libbpf fix and probe_mem sanitizing, from Andrii.

3) sock_hash fixes, from Jakub.

4) devmap_val fix, from Jesper.

5) load_bytes_relative fix, from YiFei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Looking into the context (atomic!) and the error message should be dropped.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull more cifs updates from Steve French:
 "12 cifs/smb3 fixes, 2 for stable.

   - add support for idsfromsid on create and chgrp/chown allowing
     ability to save owner information more naturally for some workloads

   - improve query info (getattr) when SMB3.1.1 posix extensions are
     negotiated by using new query info level"

* tag '5.8-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add debug message for new file creation with idsfromsid mount option
  cifs: fix chown and chgrp when idsfromsid mount option enabled
  smb3: allow uid and gid owners to be set on create with idsfromsid mount option
  smb311: Add tracepoints for new compound posix query info
  smb311: add support for using info level for posix extensions query
  smb311: Add support for lookup with posix extensions query info
  smb311: Add support for SMB311 query info (non-compounded)
  SMB311: Add support for query info using posix extensions (level 100)
  smb3: add indatalen that can be a non-zero value to calculation of credit charge in smb2 ioctl
  smb3: fix typo in mount options displayed in /proc/mounts
  cifs: Add get_security_type_str function to return sec type.
  smb3: extend fscache mount volume coherency check

Let's keep "git status" happy and quiet.

Fixes: 9762dc14 ("samples: add binderfs sample program
Fixes: fca5e949 ("samples: binderfs: really compile this sample and fix build issues")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I'm not convinced the script makes useful automaed help lines anyway,
but since we're trying to deprecate the use of "---help---" in Kconfig
files, let's fix the doc example code too.

See commit a7f7f624 ("treewide: replace '---help---' in Kconfig
files with 'help'")

Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more Kbuild updates from Masahiro Yamada:

 - fix build rules in binderfs sample

 - fix build errors when Kbuild recurses to the top Makefile

 - covert '---help---' in Kconfig to 'help'

* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  treewide: replace '---help---' in Kconfig files with 'help'
  kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
  samples: binderfs: really compile this sample and fix build issues

Pull more SCSI updates from James Bottomley:
 "This is the set of changes collected since just before the merge
  window opened. It's mostly minor fixes in drivers.

  The one non-driver set is the three optical disk (sr) changes where
  two are error path fixes and one is a helper conversion.

  The big driver change is the hpsa compat_alloc_userspace rework by Al
  so he can kill the remaining user. This has been tested and acked by
  the maintainer"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
  scsi: acornscsi: Fix an error handling path in acornscsi_probe()
  scsi: storvsc: Remove memset before memory freeing in storvsc_suspend()
  scsi: cxlflash: Remove an unnecessary NULL check
  scsi: ibmvscsi: Don't send host info in adapter info MAD after LPM
  scsi: sr: Fix sr_probe() missing deallocate of device minor
  scsi: sr: Fix sr_probe() missing mutex_destroy
  scsi: st: Convert convert get_user_pages() --> pin_user_pages()
  scsi: target: Rename target_setup_cmd_from_cdb() to target_cmd_parse_cdb()
  scsi: target: Fix NULL pointer dereference
  scsi: target: Initialize LUN in transport_init_se_cmd()
  scsi: target: Factor out a new helper, target_cmd_init_cdb()
  scsi: hpsa: hpsa_ioctl(): Tidy up a bit
  scsi: hpsa: Get rid of compat_alloc_user_space()
  scsi: hpsa: Don't bother with vmalloc for BIG_IOCTL_Command_struct
  scsi: hpsa: Lift {BIG_,}IOCTL_Command_struct copy{in,out} into hpsa_ioctl()
  scsi: ufs: Remove redundant urgent_bkop_lvl initialization
  scsi: ufs: Don't update urgent bkops level when toggling auto bkops
  scsi: qedf: Remove redundant initialization of variable rc
  scsi: mpt3sas: Fix memset() in non-RDPQ mode
  scsi: iscsi: Fix reference count leak in iscsi_boot_create_kobj
  ...

Pull i2c updates from Wolfram Sang:
 "I2C has quite some patches for you this time. I hope it is the move to
  per-driver-maintainers which is now showing results. We will see.

  The big news is two new drivers (Nuvoton NPCM and Qualcomm CCI),
  larger refactoring of the Designware, Tegra, and PXA drivers, the
  Cadence driver supports being a slave now, and there is support to
  instanciate SPD eeproms for well-known cases (which will be
  user-visible because the i801 driver supports it), and some
  devm_platform_ioremap_resource() conversions which blow up the
  diffstat.

  Note that I applied the Nuvoton driver quite late, so some minor fixup
  patches arrived during the merge window. I chose to apply them right
  away because they were trivial"

* 'i2c/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (109 commits)
  i2c: Drop stray comma in MODULE_AUTHOR statements
  i2c: npcm7xx: npcm_i2caddr[] can be static
  MAINTAINERS: npcm7xx: Add maintainer for Nuvoton NPCM BMC
  i2c: npcm7xx: Fix a couple of error codes in probe
  i2c: icy: Fix build with CONFIG_AMIGA_PCMCIA=n
  i2c: npcm7xx: Remove unnecessary parentheses
  i2c: npcm7xx: Add support for slave mode for Nuvoton
  i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver
  dt-bindings: i2c: npcm7xx: add NPCM I2C controller
  i2c: pxa: don't error out if there's no pinctrl
  i2c: add 'single-master' property to generic bindings
  i2c: designware: Add Baikal-T1 System I2C support
  i2c: designware: Move reg-space remapping into a dedicated function
  i2c: designware: Retrieve quirk flags as early as possible
  i2c: designware: Convert driver to using regmap API
  i2c: designware: Discard Cherry Trail model flag
  i2c: designware: Add Baytrail sem config DW I2C platform dependency
  i2c: designware: slave: Set DW I2C core module dependency
  i2c: designware: Use `-y` to build multi-object modules
  dt-bindings: i2c: dw: Add Baikal-T1 SoC I2C controller
  ...

Pull more media updates from Mauro Carvalho Chehab:

 - a set of atomisp patches. They remove several abstraction layers, and
   fixes clang and gcc warnings (that were hidden via some macros that
   were disabling 4 or 5 types of warnings there). There are also some
   important fixes and sensor auto-detection on newer BIOSes via ACPI
   _DCM tables.

 - some fixes

* tag 'media/v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (95 commits)
  media: rkvdec: Fix H264 scaling list order
  media: v4l2-ctrls: Unset correct HEVC loop filter flag
  media: videobuf2-dma-contig: fix bad kfree in vb2_dma_contig_clear_max_seg_size
  media: v4l2-subdev.rst: correct information about v4l2 events
  media: s5p-mfc: Properly handle dma_parms for the allocated devices
  media: medium: cec: Make MEDIA_CEC_SUPPORT default to n if !MEDIA_SUPPORT
  media: cedrus: Implement runtime PM
  media: cedrus: Program output format during each run
  media: atomisp: improve ACPI/DMI detection logs
  media: Revert "media: atomisp: add Asus Transform T101HA ACPI vars"
  media: Revert "media: atomisp: Add some ACPI detection info"
  media: atomisp: improve sensor detection code to use _DSM table
  media: atomisp: get rid of an iomem abstraction layer
  media: atomisp: get rid of a string_support.h abstraction layer
  media: atomisp: use strscpy() instead of less secure variants
  media: atomisp: set DFS to MAX if sensor doesn't report fps
  media: atomisp: use different dfs failed messages
  media: atomisp: change the detection of ISP2401 at runtime
  media: atomisp: use macros from intel-family.h
  media: atomisp: don't set hpll_freq twice with different values
  ...

Pull libnvdimm updates from Dan Williams:
 "Small collection of cleanups to rework usage of ->queuedata and the
  GUID api"

* tag 'libnvdimm-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nvdimm/pmem: stop using ->queuedata
  nvdimm/btt: stop using ->queuedata
  nvdimm/blk: stop using ->queuedata
  libnvdimm: Replace guid_copy() with import_guid() where it makes sense

Let's keep "git status" happy and quiet.

Fixes: f5b5a164 ("Add sample notification program")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull iomap fix from Darrick Wong:
 "A single iomap bug fix for a variable type mistake on 32-bit
  architectures, fixing an integer overflow problem in the unshare
  actor"

* tag 'iomap-5.8-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: Fix unsharing of an extent >2GB on a 32-bit machine

Pull xfs fix from Darrick Wong:
 "We've settled down into the bugfix phase; this one fixes a resource
  leak on an error bailout path"

* tag 'xfs-5.8-merge-9' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: Add the missed xfs_perag_put() for xfs_ifree_cluster()

Pull 9p update from Dominique Martinet:
 "Another very quiet cycle... Only one commit: increase the size of the
  ring used for xen transport"

* tag '9p-for-5.8' of git://github.com/martinetd/linux:
  9p/xen: increase XEN_9PFS_RING_ORDER

Pull powerpc fix from Michael Ellerman:
 "One fix for a recent change which broke nested KVM guests on Power9.

  Thanks to Alexey Kardashevskiy"

* tag 'powerpc-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  KVM: PPC: Fix nested guest RC bits update

Pull ARM fixes from Russell King:

 - fix for "hex" Kconfig default to use 0x0 rather than 0 to allow these
   to be removed from defconfigs

 - fix from Ard Biesheuvel for EFI HYP mode booting

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8985/1: efi/decompressor: deal with HYP mode boot gracefully
  ARM: 8984/1: Kconfig: set default ZBOOT_ROM_TEXT/BSS value to 0x0