The ssbi driver's read/write entry points are protected with wrappers
in the case when the driver isn't enabled.  These wrappers don't make
any sense, since a client of the SSBI bus won't work without it.  Make
these just regular functions, so that the SSBI driver can be built as
a module.
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

msm_ssbi_remove is referenced with __exit_p, but not declared with
__exit.  This causes a warning when the driver is not built as a
module:

drivers/ssbi/ssbi.c:341:23: warning: 'msm_ssbi_remove' defined but not used [-Wunused-function]

The remove is needed for unbinding to work, even if not compiled as a
module, so just remove it.
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SSBI is the Qualcomm single-wire serial bus interface used to connect
the MSM devices to the PMIC and other devices.

Since SSBI only supports a single slave, the driver gets the name of the
slave device passed in from the board file through the master device's
platform data.

SSBI registers pretty early (postcore), so that the PMIC can come up
before the board init. This is useful if the board init requires the
use of gpios that are connected through the PMIC.

Based on a patch by Dima Zavin <dima@android.com> that can be found at:
http://android.git.kernel.org/?p=kernel/msm.git;a=commitdiff;h=eb060bac4

This patch adds PMIC Arbiter support for the MSM8660. The PMIC Arbiter
is a hardware wrapper around the SSBI 2.0 controller that is designed to
overcome concurrency issues and security limitations.  A controller_type
field is added to the platform data to specify the type of the SSBI
controller (1.0, 2.0, or PMIC Arbiter).

[davidb@codeaurora.org:
 I've moved this driver into drivers/ssbi/ and added an include for
 linux/module.h so that it will compile]
Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce the module_pcmcia_driver() macro which is a convenience macro
for pcmcia driver modules. It is intended to be used by pcmcia drivers
with init/exit sections that do nothing but register/unregister the
pcmcia driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: linux-pcmcia@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch converts the drivers to use the
module_platform_driver_probe() macro which makes the code smaller and
a bit simpler.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We're iterating through abps[] printing information, but here we
use the wrong array index.  IndexCard comes from the user and in
this case it was specifically not range checked because we didn't
expect to use it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

One function is ipack_device_init(). If it fails, the caller should execute
ipack_put_device().

The second function is ipack_device_add that only adds the device. If
it fails, the caller should execute ipack_put_device().

Then the device is removed with refcount = 0, as device_register() kernel
documentation says.

ipack_device_del() is added to remove the device.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare everything for later use.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

De-activating this reading back will effectively half the time required
for a write to the output register.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver supports host initiated backup of the guest. On Windows guests,
the host can generate application consistent backups using the Windows VSS
framework. On Linux, we ensure that the backup will be file system consistent.
This driver allows the host to initiate a  "Freeze" operation on all the mounted
file systems in the guest. Once the mounted file systems in the guest are frozen,
the host snapshots the guest's file systems. Once this is done, the guest's file
systems are "thawed".

This driver has a user-level component (daemon) that invokes the appropriate
operation on all the mounted file systems in response to the requests from
the host. The duration for which the guest is frozen is very short - a few seconds.
During this interval, the diff disk is comitted.

In this version of the patch I have addressed the feedback from Olaf Herring.
Also, some of the connector related issues have been fixed.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Properly cleanup the channel state on receipt of the "offer rescind" message.
Starting with ws2012, the host requires that the channel "relid" be properly
cleaned up when the offer is rescinded.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Implement the memory hot-add functionality. With this, Linux guests can fully
participate in the Dynamic Memory protocol implemented in the Windows hosts.

In this version of the patch, based Olaf Herring's feedback, I have gotten
rid of the module level dependency on MEMORY_HOTPLUG. Instead the code within
the driver that depends on MEMORY_HOTPLUG has the appropriate compilation
switches. This would allow this driver to support pure ballooning in cases
where the kernel does not support memory hotplug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The balloon driver is stateful. For instance, it needs to keep track of pages
that have been ballooned out to properly post pressure reports. This state cannot
be re-constructed if the driver were to be unloaded and subsequently loaded.
Furthermore, as we support memory hot-add as part of this driver, this driver becomes
even more stateful and this state cannot be re-created. Make the balloon driver
unloadable to deal with this issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Execute the hot-add operation in a separate work context.
This allows us to decouple the pressure reporting activity from the
"hot-add" activity. Testing has shown that this makes the guest more
responsive to hot add requests.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Execute the balloon inflation operation in a separate work context.
This allows us to decouple the pressure reporting activity from the
ballooning activity. Testing has shown that this decoupling makes the
guest more reponsive.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no need to request completion notification; get rid of it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HyperV KVP daemon should check nlmsg_type in received netlink message
header. If message type is NLMSG_DONE daemon can proceed with processing
otherwise it should wait for next message.
Signed-off-by: Tomas Hozza <thozza@redhat.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HyperV daemon should use macros for option values when calling setsockopt.
Using specific numeric values instead of macros is confusing.
Signed-off-by: Tomas Hozza <thozza@redhat.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Previously HyperV daemon set sockaddr_nl.nl_groups to CN_KVP_IDX.
Netlink documentation says: "nl_groups is a bit mask with every bit
representing a netlink group number". Since CN_KVP_IDX value is "9"
HyperV daemon was receiving Netlink messages also from group number
"1" which is used by CGroup Rules Engine Daemon. This caused the
daemon to segfault (at least on 2.6.32 kernel).

HyperV daemon should set nl_groups to zero and specify multicast
group CN_KVP_IDX only by using socket options.
Signed-off-by: Tomas Hozza <thozza@redhat.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

remove cast for kmalloc return value.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch converts the drivers to use the
module_platform_driver_probe() macro which makes the code smaller and
a bit simpler.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Aneesh V <aneesh@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 20259849 ("VMCI: Some header and
config files.") readded this Makefile line. Remove it again.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

  APDS_RANGE is 65535, chip->lux_calib is u16 (never more than APDS_RANGE).
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Building the vmw_vmci driver with CONFIG_NET undefined results in:

drivers/built-in.o: In function `__qp_memcpy_from_queue.isra.13':
vmci_queue_pair.c:(.text+0x1671a8): undefined reference to `memcpy_toiovec'
drivers/built-in.o: In function `__qp_memcpy_to_queue.isra.14':
vmci_queue_pair.c:(.text+0x167341): undefined reference to `memcpy_fromiovec'
make[1]: [vmlinux] Error 1 (ignored)

since memcpy_toiovec and memcpy_fromiovec are defined in the networking code.
Add the missing dependency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>